[PATCH v2 1/6] binding-doc: power: pwrseq-generic: add binding doc for generic power sequence library

[hzpeterchen@gmail.com (Peter Chen)]

On Sat, Jul 16, 2016 at 05:30:57PM -0500, Rob Herring wrote:
> On Wed, Jul 13, 2016 at 10:06:45AM +0800, Peter Chen wrote:
> > Add binding doc for generic power sequence library.
> 
> I'd written a review on last version, but forgot to send it out. Anyway, 
> I mostly had the same comments as Philipp and Joshua. A couple of things 
> they missed...
> 
> > 
> > Signed-off-by: Peter Chen <peter.chen@nxp.com>
> > ---
> >  .../bindings/power/pwrseq/pwrseq-generic.txt       | 53 ++++++++++++++++++++++
> >  1 file changed, 53 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> > 
> > diff --git a/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> > new file mode 100644
> > index 0000000..186c58c
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/power/pwrseq/pwrseq-generic.txt
> > @@ -0,0 +1,53 @@
> > +The generic power sequence library
> > +
> > +Some hard-wired USB/MMC devices need to do power sequence to let the
> > +device work normally, the typical power sequence like: enable USB
> > +PHY clock, toggle reset pin, etc. But current Linux USB driver
> > +lacks of such code to do it, it may cause some hard-wired USB devices
> > +works abnormal or can't be recognized by controller at all. The
> > +power sequence will be done before this device can be found at USB
> > +bus.
> > +
> > +The power sequence properties is under the device node.
> > +
> > +Required properties:
> > +- power-sequence: this device needs to do power sequence before enumeration
> > +
> > +Optional properties:
> > +- clocks: the input clock for device.
> > +- reset-gpios: Should specify the GPIO for reset.
> > +- reset-duration-us: the duration in microsecond for assert reset signal.
> > +
> > +Below is the example of USB power sequence properties on USB device
> > +nodes which have two level USB hubs.
> > +
> > +&usbotg1 {
> > +	vbus-supply = <&reg_usb_otg1_vbus>;
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&pinctrl_usb_otg1_id>;
> > +	status = "okay";
> > +
> > +	#address-cells = <1>;
> > +	#size-cells = <0>;
> > +	hub: genesys at 1 {
> 
> genesys: hub at 1
> 
> > +		compatible = "usb5e3,608";
> > +		reg = <1>;
> > +
> > +		power-sequence;
> > +		clocks = <&clks IMX6SX_CLK_CKO>;
> > +		reset-gpios = <&gpio4 5 GPIO_ACTIVE_LOW>; /* hub reset pin */
> > +		reset-duration-us = <10>;
> > +
> > +		#address-cells = <1>;
> > +		#size-cells = <0>;
> > +		ethernet: asix at 1 {
> 
> asix: ethernet at 1
> 
> > +			compatible = "usbb95,1708";
> > +			reg = <1>;
> > +
> > +			power-sequence;
> > +			clocks = <&clks IMX6SX_CLK_IPG>;
> > +			reset-gpios = <&gpio4 6 GPIO_ACTIVE_LOW>; /* ethernet_rst */
> > +			reset-duration-us = <15>;
> > +		};
> > +	};
> > +};

Will change, thanks.

-- 

Best Regards,
Peter Chen