* [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058
@ 2016-11-03 9:13 Linus Walleij
2016-11-03 9:13 ` [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent Linus Walleij
` (2 more replies)
0 siblings, 3 replies; 6+ messages in thread
From: Linus Walleij @ 2016-11-03 9:13 UTC (permalink / raw)
To: linux-arm-kernel
The name "pmicintc" is ambiguous: there is a second power
management IC named PM8901 on these systems, and it is also
an interrupt controller. To make things clear, just name the
node alias "pm8058", this in unambigous and has all information
we need.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 2 +-
arch/arm/boot/dts/qcom-msm8660-surf.dts | 2 +-
arch/arm/boot/dts/qcom-msm8660.dtsi | 12 ++++++------
3 files changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 4b8872cc8bf9..4a532ddab53a 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -412,7 +412,7 @@
* The second interrupt is the PME interrupt
* for network wakeup, connected to the TLMM.
*/
- interrupts-extended = <&pmicintc 198 IRQ_TYPE_EDGE_FALLING>,
+ interrupts-extended = <&pm8058 198 IRQ_TYPE_EDGE_FALLING>,
<&tlmm 29 IRQ_TYPE_EDGE_RISING>;
reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
vdd33a-supply = <&dragon_veth>;
diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
index 23de764558ab..1adc04978a47 100644
--- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
+++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
@@ -48,7 +48,7 @@
};
};
-&pmicintc {
+&pm8058 {
keypad at 148 {
linux,keymap = <
MATRIX_KEY(0, 0, KEY_FN_F1)
diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
index 4d828f810746..91c9a62ae725 100644
--- a/arch/arm/boot/dts/qcom-msm8660.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
@@ -163,7 +163,7 @@
reg = <0x500000 0x1000>;
qcom,controller-type = "pmic-arbiter";
- pmicintc: pmic at 0 {
+ pm8058: pmic at 0 {
compatible = "qcom,pm8058";
interrupt-parent = <&tlmm>;
interrupts = <88 8>;
@@ -176,7 +176,7 @@
compatible = "qcom,pm8058-gpio",
"qcom,ssbi-gpio";
reg = <0x150>;
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8058>;
interrupts = <192 IRQ_TYPE_NONE>,
<193 IRQ_TYPE_NONE>,
<194 IRQ_TYPE_NONE>,
@@ -232,7 +232,7 @@
reg = <0x50>;
gpio-controller;
#gpio-cells = <2>;
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8058>;
interrupts =
<128 IRQ_TYPE_NONE>,
<129 IRQ_TYPE_NONE>,
@@ -251,7 +251,7 @@
pwrkey at 1c {
compatible = "qcom,pm8058-pwrkey";
reg = <0x1c>;
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8058>;
interrupts = <50 1>, <51 1>;
debounce = <15625>;
pull-up;
@@ -260,7 +260,7 @@
keypad at 148 {
compatible = "qcom,pm8058-keypad";
reg = <0x148>;
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8058>;
interrupts = <74 1>, <75 1>;
debounce = <15>;
scan-delay = <32>;
@@ -270,7 +270,7 @@
rtc at 1e8 {
compatible = "qcom,pm8058-rtc";
reg = <0x1e8>;
- interrupt-parent = <&pmicintc>;
+ interrupt-parent = <&pm8058>;
interrupts = <39 1>;
allow-set-time;
};
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent
2016-11-03 9:13 [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Linus Walleij
@ 2016-11-03 9:13 ` Linus Walleij
2016-11-03 21:53 ` Bjorn Andersson
2016-11-03 9:13 ` [PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard Linus Walleij
2016-11-03 21:50 ` [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Bjorn Andersson
2 siblings, 1 reply; 6+ messages in thread
From: Linus Walleij @ 2016-11-03 9:13 UTC (permalink / raw)
To: linux-arm-kernel
Some nodes are referencing the pm8058_gpio as IRQ parent, but
the HW IRQ offset they are supplying is actually that for the
parent to that controller: the PM8058 itself. Since that is the
proper parent, reference it directly.
We can switch this to the pm8058_gpio and the proper offset
once we have fixed the SSBI GPIO driver to properly deal with
the hierarchical IRQ domain and get proper local offset
translation.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index 4a532ddab53a..ea660ffa03ea 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -369,8 +369,8 @@
ak8975 at 0c {
compatible = "asahi-kasei,ak8975";
reg = <0x0c>;
- /* GPIO33 has interrupt 224 on the PM8058 */
- interrupt-parent = <&pm8058_gpio>;
+ /* FIXME: GPIO33 has interrupt 224 on the PM8058 */
+ interrupt-parent = <&pm8058>;
interrupts = <224 IRQ_TYPE_EDGE_RISING>;
pinctrl-names = "default";
pinctrl-0 = <&dragon_ak8975_gpios>;
@@ -380,8 +380,8 @@
bmp085 at 77 {
compatible = "bosch,bmp085";
reg = <0x77>;
- /* GPIO16 has interrupt 207 on the PM8058 */
- interrupt-parent = <&pm8058_gpio>;
+ /* FIXME: GPIO16 has interrupt 207 on the PM8058 */
+ interrupt-parent = <&pm8058>;
interrupts = <207 IRQ_TYPE_EDGE_RISING>;
reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard
2016-11-03 9:13 [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Linus Walleij
2016-11-03 9:13 ` [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent Linus Walleij
@ 2016-11-03 9:13 ` Linus Walleij
2016-11-03 21:54 ` Bjorn Andersson
2016-11-03 21:50 ` [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Bjorn Andersson
2 siblings, 1 reply; 6+ messages in thread
From: Linus Walleij @ 2016-11-03 9:13 UTC (permalink / raw)
To: linux-arm-kernel
This adds the MPU-3050 gyroscope and the KXSD9 accelerometer to
the Qualcomm APQ8060 Dragonboard. The KXSD9 is mounted beyond the
MPU-3050 and appear as a subdevice beyond it. We set up the
required GPIO and interrupt lines to make the devices work.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ChangeLog v2->v3:
- Move the interrupt to the pm8058 alias to reflect the two patches
properly specifying the PMIC as interrupt parent.
ChangeLog v1->v2:
- Use the new I2C mux gate bindings from Peter Rosin (merged to
the I2C subsystem)
---
arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 53 ++++++++++++++++++++++++++
1 file changed, 53 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
index ea660ffa03ea..c1b99c9cb318 100644
--- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
+++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
@@ -220,6 +220,14 @@
function = "ebi2";
};
};
+
+ /* Interrupt line for the KXSD9 accelerometer */
+ dragon_kxsd9_gpios: kxsd9 {
+ irq {
+ pins = "gpio57"; /* IRQ line */
+ bias-pull-up;
+ };
+ };
};
qcom,ssbi at 500000 {
@@ -272,6 +280,15 @@
power-source = <PM8058_GPIO_S3>;
};
};
+ dragon_mpu3050_gpios: mpu3050-gpios {
+ pinconf {
+ pins = "gpio17";
+ function = "normal";
+ input-enable;
+ bias-disable;
+ power-source = <PM8058_GPIO_S3>;
+ };
+ };
dragon_sdcc3_gpios: sdcc3-gpios {
pinconf {
pins = "gpio22";
@@ -389,6 +406,42 @@
vddd-supply = <&pm8058_lvs0>; // 1.8V
vdda-supply = <&pm8058_l14>; // 2.85V
};
+ mpu3050 at 68 {
+ compatible = "invensense,mpu3050";
+ reg = <0x68>;
+ /*
+ * GPIO17 has interrupt 208 on the
+ * PM8058, it is pulled high by a 10k
+ * resistor to VLOGIC so needs to be
+ * active low/falling edge.
+ */
+ interrupt-parent = <&pm8058>;
+ interrupts = <208 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_mpu3050_gpios>;
+ vlogic-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
+
+ /*
+ * The MPU-3050 acts as a hub for the
+ * accelerometer.
+ */
+ i2c-gate {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ kxsd9 at 18 {
+ compatible = "kionix,kxsd9";
+ reg = <0x18>;
+ interrupt-parent = <&tlmm>;
+ interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&dragon_kxsd9_gpios>;
+ iovdd-supply = <&pm8058_lvs0>; // 1.8V
+ vdd-supply = <&pm8058_l14>; // 2.85V
+ };
+ };
+ };
};
};
--
2.7.4
^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058
2016-11-03 9:13 [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Linus Walleij
2016-11-03 9:13 ` [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent Linus Walleij
2016-11-03 9:13 ` [PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard Linus Walleij
@ 2016-11-03 21:50 ` Bjorn Andersson
2 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2016-11-03 21:50 UTC (permalink / raw)
To: linux-arm-kernel
On Thu 03 Nov 02:13 PDT 2016, Linus Walleij wrote:
> The name "pmicintc" is ambiguous: there is a second power
> management IC named PM8901 on these systems, and it is also
> an interrupt controller. To make things clear, just name the
> node alias "pm8058", this in unambigous and has all information
> we need.
>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
> arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 2 +-
> arch/arm/boot/dts/qcom-msm8660-surf.dts | 2 +-
> arch/arm/boot/dts/qcom-msm8660.dtsi | 12 ++++++------
> 3 files changed, 8 insertions(+), 8 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> index 4b8872cc8bf9..4a532ddab53a 100644
> --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> @@ -412,7 +412,7 @@
> * The second interrupt is the PME interrupt
> * for network wakeup, connected to the TLMM.
> */
> - interrupts-extended = <&pmicintc 198 IRQ_TYPE_EDGE_FALLING>,
> + interrupts-extended = <&pm8058 198 IRQ_TYPE_EDGE_FALLING>,
> <&tlmm 29 IRQ_TYPE_EDGE_RISING>;
> reset-gpios = <&tlmm 30 GPIO_ACTIVE_LOW>;
> vdd33a-supply = <&dragon_veth>;
> diff --git a/arch/arm/boot/dts/qcom-msm8660-surf.dts b/arch/arm/boot/dts/qcom-msm8660-surf.dts
> index 23de764558ab..1adc04978a47 100644
> --- a/arch/arm/boot/dts/qcom-msm8660-surf.dts
> +++ b/arch/arm/boot/dts/qcom-msm8660-surf.dts
> @@ -48,7 +48,7 @@
> };
> };
>
> -&pmicintc {
> +&pm8058 {
> keypad at 148 {
> linux,keymap = <
> MATRIX_KEY(0, 0, KEY_FN_F1)
> diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
> index 4d828f810746..91c9a62ae725 100644
> --- a/arch/arm/boot/dts/qcom-msm8660.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
> @@ -163,7 +163,7 @@
> reg = <0x500000 0x1000>;
> qcom,controller-type = "pmic-arbiter";
>
> - pmicintc: pmic at 0 {
> + pm8058: pmic at 0 {
> compatible = "qcom,pm8058";
> interrupt-parent = <&tlmm>;
> interrupts = <88 8>;
> @@ -176,7 +176,7 @@
> compatible = "qcom,pm8058-gpio",
> "qcom,ssbi-gpio";
> reg = <0x150>;
> - interrupt-parent = <&pmicintc>;
> + interrupt-parent = <&pm8058>;
> interrupts = <192 IRQ_TYPE_NONE>,
> <193 IRQ_TYPE_NONE>,
> <194 IRQ_TYPE_NONE>,
> @@ -232,7 +232,7 @@
> reg = <0x50>;
> gpio-controller;
> #gpio-cells = <2>;
> - interrupt-parent = <&pmicintc>;
> + interrupt-parent = <&pm8058>;
> interrupts =
> <128 IRQ_TYPE_NONE>,
> <129 IRQ_TYPE_NONE>,
> @@ -251,7 +251,7 @@
> pwrkey at 1c {
> compatible = "qcom,pm8058-pwrkey";
> reg = <0x1c>;
> - interrupt-parent = <&pmicintc>;
> + interrupt-parent = <&pm8058>;
> interrupts = <50 1>, <51 1>;
> debounce = <15625>;
> pull-up;
> @@ -260,7 +260,7 @@
> keypad at 148 {
> compatible = "qcom,pm8058-keypad";
> reg = <0x148>;
> - interrupt-parent = <&pmicintc>;
> + interrupt-parent = <&pm8058>;
> interrupts = <74 1>, <75 1>;
> debounce = <15>;
> scan-delay = <32>;
> @@ -270,7 +270,7 @@
> rtc at 1e8 {
> compatible = "qcom,pm8058-rtc";
> reg = <0x1e8>;
> - interrupt-parent = <&pmicintc>;
> + interrupt-parent = <&pm8058>;
> interrupts = <39 1>;
> allow-set-time;
> };
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent
2016-11-03 9:13 ` [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent Linus Walleij
@ 2016-11-03 21:53 ` Bjorn Andersson
0 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2016-11-03 21:53 UTC (permalink / raw)
To: linux-arm-kernel
On Thu 03 Nov 02:13 PDT 2016, Linus Walleij wrote:
> Some nodes are referencing the pm8058_gpio as IRQ parent, but
> the HW IRQ offset they are supplying is actually that for the
> parent to that controller: the PM8058 itself. Since that is the
> proper parent, reference it directly.
>
> We can switch this to the pm8058_gpio and the proper offset
> once we have fixed the SSBI GPIO driver to properly deal with
> the hierarchical IRQ domain and get proper local offset
> translation.
>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
> arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 8 ++++----
> 1 file changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> index 4a532ddab53a..ea660ffa03ea 100644
> --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> @@ -369,8 +369,8 @@
> ak8975 at 0c {
> compatible = "asahi-kasei,ak8975";
> reg = <0x0c>;
> - /* GPIO33 has interrupt 224 on the PM8058 */
> - interrupt-parent = <&pm8058_gpio>;
> + /* FIXME: GPIO33 has interrupt 224 on the PM8058 */
> + interrupt-parent = <&pm8058>;
> interrupts = <224 IRQ_TYPE_EDGE_RISING>;
> pinctrl-names = "default";
> pinctrl-0 = <&dragon_ak8975_gpios>;
> @@ -380,8 +380,8 @@
> bmp085 at 77 {
> compatible = "bosch,bmp085";
> reg = <0x77>;
> - /* GPIO16 has interrupt 207 on the PM8058 */
> - interrupt-parent = <&pm8058_gpio>;
> + /* FIXME: GPIO16 has interrupt 207 on the PM8058 */
> + interrupt-parent = <&pm8058>;
> interrupts = <207 IRQ_TYPE_EDGE_RISING>;
> reset-gpios = <&tlmm 86 GPIO_ACTIVE_LOW>;
> pinctrl-names = "default";
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard
2016-11-03 9:13 ` [PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard Linus Walleij
@ 2016-11-03 21:54 ` Bjorn Andersson
0 siblings, 0 replies; 6+ messages in thread
From: Bjorn Andersson @ 2016-11-03 21:54 UTC (permalink / raw)
To: linux-arm-kernel
On Thu 03 Nov 02:13 PDT 2016, Linus Walleij wrote:
> This adds the MPU-3050 gyroscope and the KXSD9 accelerometer to
> the Qualcomm APQ8060 Dragonboard. The KXSD9 is mounted beyond the
> MPU-3050 and appear as a subdevice beyond it. We set up the
> required GPIO and interrupt lines to make the devices work.
>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I still would have preferred you using interrupts-extended when you're
specifying both parent and irq specifier anyways, but I'm ok with this.
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
> ChangeLog v2->v3:
> - Move the interrupt to the pm8058 alias to reflect the two patches
> properly specifying the PMIC as interrupt parent.
> ChangeLog v1->v2:
> - Use the new I2C mux gate bindings from Peter Rosin (merged to
> the I2C subsystem)
> ---
> arch/arm/boot/dts/qcom-apq8060-dragonboard.dts | 53 ++++++++++++++++++++++++++
> 1 file changed, 53 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> index ea660ffa03ea..c1b99c9cb318 100644
> --- a/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> +++ b/arch/arm/boot/dts/qcom-apq8060-dragonboard.dts
> @@ -220,6 +220,14 @@
> function = "ebi2";
> };
> };
> +
> + /* Interrupt line for the KXSD9 accelerometer */
> + dragon_kxsd9_gpios: kxsd9 {
> + irq {
> + pins = "gpio57"; /* IRQ line */
> + bias-pull-up;
> + };
> + };
> };
>
> qcom,ssbi at 500000 {
> @@ -272,6 +280,15 @@
> power-source = <PM8058_GPIO_S3>;
> };
> };
> + dragon_mpu3050_gpios: mpu3050-gpios {
> + pinconf {
> + pins = "gpio17";
> + function = "normal";
> + input-enable;
> + bias-disable;
> + power-source = <PM8058_GPIO_S3>;
> + };
> + };
> dragon_sdcc3_gpios: sdcc3-gpios {
> pinconf {
> pins = "gpio22";
> @@ -389,6 +406,42 @@
> vddd-supply = <&pm8058_lvs0>; // 1.8V
> vdda-supply = <&pm8058_l14>; // 2.85V
> };
> + mpu3050 at 68 {
> + compatible = "invensense,mpu3050";
> + reg = <0x68>;
> + /*
> + * GPIO17 has interrupt 208 on the
> + * PM8058, it is pulled high by a 10k
> + * resistor to VLOGIC so needs to be
> + * active low/falling edge.
> + */
> + interrupt-parent = <&pm8058>;
> + interrupts = <208 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&dragon_mpu3050_gpios>;
> + vlogic-supply = <&pm8058_lvs0>; // 1.8V
> + vdd-supply = <&pm8058_l14>; // 2.85V
> +
> + /*
> + * The MPU-3050 acts as a hub for the
> + * accelerometer.
> + */
> + i2c-gate {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + kxsd9 at 18 {
> + compatible = "kionix,kxsd9";
> + reg = <0x18>;
> + interrupt-parent = <&tlmm>;
> + interrupts = <57 IRQ_TYPE_EDGE_FALLING>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&dragon_kxsd9_gpios>;
> + iovdd-supply = <&pm8058_lvs0>; // 1.8V
> + vdd-supply = <&pm8058_l14>; // 2.85V
> + };
> + };
> + };
> };
> };
>
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-11-03 21:54 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-11-03 9:13 [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Linus Walleij
2016-11-03 9:13 ` [PATCH 2/3] ARM: dts: reference PM8058 as IRQ parent Linus Walleij
2016-11-03 21:53 ` Bjorn Andersson
2016-11-03 9:13 ` [PATCH 3/3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard Linus Walleij
2016-11-03 21:54 ` Bjorn Andersson
2016-11-03 21:50 ` [PATCH 1/3] ARM: dts: rename MSM8660/APQ8060 pmicintc to pm8058 Bjorn Andersson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).