* [PATCH v2 1/9] ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 2/9] ARM: dra72-evm: Fix modelling of regulators Lokesh Vutla
` (8 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
Pinmuxing for DRA7x/AM57x family of processors need to be done in IO
isolation as part of initial bootloader executed from SRAM. This is
done as part of iodelay configuration sequence and is required due
to the limitations introduced by erratum ID: i869[1] (IO Glitches
can occur when changing IO settings) and elaborated in the Technical
Reference Manual[2] 18.4.6.1.7 Isolation Requirements.
Only peripheral that is permitted for dynamic pin mux configuration
is MMC and DCAN. MMC is permitted to change to accommodate the
requirements for varied speeds (which require IO-delay support in
kernel as well). DCAN is a result of i893[1] (DCAN initialization
sequence). With the exception of DCAN and MMC, all other pin mux
configurations are removed from the dts.
[1] http://www.ti.com/lit/er/sprz436a/sprz436a.pdf
[2] http://www.ti.com/lit/ug/spruhz7c/spruhz7c.pdf
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/boot/dts/dra72-evm-common.dtsi | 192 --------------------------------
1 file changed, 192 deletions(-)
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index c94d8d64..3c02612 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -69,9 +69,6 @@
tpd12s015: encoder {
compatible = "ti,tpd12s015";
- pinctrl-names = "default";
- pinctrl-0 = <&tpd12s015_pins>;
-
gpios = <&pcf_hdmi 4 GPIO_ACTIVE_HIGH>, /* P4, CT CP HPD */
<&pcf_hdmi 5 GPIO_ACTIVE_HIGH>, /* P5, LS OE */
<&gpio7 12 GPIO_ACTIVE_HIGH>; /* gpio7_12/sp1_cs2, HPD */
@@ -134,72 +131,6 @@
};
&dra7_pmx_core {
- i2c1_pins: pinmux_i2c1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3800, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
- DRA7XX_CORE_IOPAD(0x3804, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
- >;
- };
-
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
- DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
- >;
- };
-
- i2c5_pins: pinmux_i2c5_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x36b4, PIN_INPUT | MUX_MODE10) /* mcasp1_axr0.i2c5_sda */
- DRA7XX_CORE_IOPAD(0x36b8, PIN_INPUT | MUX_MODE10) /* mcasp1_axr1.i2c5_scl */
- >;
- };
-
- nand_default: nand_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3400, PIN_INPUT | MUX_MODE0) /* gpmc_ad0 */
- DRA7XX_CORE_IOPAD(0x3404, PIN_INPUT | MUX_MODE0) /* gpmc_ad1 */
- DRA7XX_CORE_IOPAD(0x3408, PIN_INPUT | MUX_MODE0) /* gpmc_ad2 */
- DRA7XX_CORE_IOPAD(0x340c, PIN_INPUT | MUX_MODE0) /* gpmc_ad3 */
- DRA7XX_CORE_IOPAD(0x3410, PIN_INPUT | MUX_MODE0) /* gpmc_ad4 */
- DRA7XX_CORE_IOPAD(0x3414, PIN_INPUT | MUX_MODE0) /* gpmc_ad5 */
- DRA7XX_CORE_IOPAD(0x3418, PIN_INPUT | MUX_MODE0) /* gpmc_ad6 */
- DRA7XX_CORE_IOPAD(0x341c, PIN_INPUT | MUX_MODE0) /* gpmc_ad7 */
- DRA7XX_CORE_IOPAD(0x3420, PIN_INPUT | MUX_MODE0) /* gpmc_ad8 */
- DRA7XX_CORE_IOPAD(0x3424, PIN_INPUT | MUX_MODE0) /* gpmc_ad9 */
- DRA7XX_CORE_IOPAD(0x3428, PIN_INPUT | MUX_MODE0) /* gpmc_ad10 */
- DRA7XX_CORE_IOPAD(0x342c, PIN_INPUT | MUX_MODE0) /* gpmc_ad11 */
- DRA7XX_CORE_IOPAD(0x3430, PIN_INPUT | MUX_MODE0) /* gpmc_ad12 */
- DRA7XX_CORE_IOPAD(0x3434, PIN_INPUT | MUX_MODE0) /* gpmc_ad13 */
- DRA7XX_CORE_IOPAD(0x3438, PIN_INPUT | MUX_MODE0) /* gpmc_ad14 */
- DRA7XX_CORE_IOPAD(0x343c, PIN_INPUT | MUX_MODE0) /* gpmc_ad15 */
- DRA7XX_CORE_IOPAD(0x34b4, PIN_OUTPUT | MUX_MODE0) /* gpmc_cs0 */
- DRA7XX_CORE_IOPAD(0x34c4, PIN_OUTPUT | MUX_MODE0) /* gpmc_advn_ale */
- DRA7XX_CORE_IOPAD(0x34cc, PIN_OUTPUT | MUX_MODE0) /* gpmc_wen */
- DRA7XX_CORE_IOPAD(0x34c8, PIN_OUTPUT | MUX_MODE0) /* gpmc_oen_ren */
- DRA7XX_CORE_IOPAD(0x34d0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ben0 */
- DRA7XX_CORE_IOPAD(0x34d8, PIN_INPUT | MUX_MODE0) /* gpmc_wait0 */
- >;
- };
-
- usb1_pins: pinmux_usb1_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3680, PIN_INPUT_SLEW | MUX_MODE0) /* usb1_drvvbus */
- >;
- };
-
- usb2_pins: pinmux_usb2_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3684, PIN_INPUT_SLEW | MUX_MODE0) /* usb2_drvvbus */
- >;
- };
-
- tps65917_pins_default: tps65917_pins_default {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3824, PIN_INPUT_PULLUP | MUX_MODE1) /* wakeup3.sys_nirq1 */
- >;
- };
-
mmc1_pins_default: mmc1_pins_default {
pinctrl-single,pins = <
DRA7XX_CORE_IOPAD(0x376c, PIN_INPUT | MUX_MODE14) /* mmc1sdcd.gpio219 */
@@ -240,59 +171,16 @@
DRA7XX_CORE_IOPAD(0x3818, MUX_MODE15 | PULL_UP) /* wakeup0.off */
>;
};
-
- hdmi_pins: pinmux_hdmi_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3808, PIN_INPUT | MUX_MODE1) /* i2c2_sda.hdmi1_ddc_scl */
- DRA7XX_CORE_IOPAD(0x380c, PIN_INPUT | MUX_MODE1) /* i2c2_scl.hdmi1_ddc_sda */
- >;
- };
-
- tpd12s015_pins: pinmux_tpd12s015_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x37b8, PIN_INPUT_PULLDOWN | MUX_MODE14) /* gpio7_12 HPD */
- >;
- };
-
- atl_pins: pinmux_atl_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3698, PIN_OUTPUT | MUX_MODE5) /* xref_clk1.atl_clk1 */
- DRA7XX_CORE_IOPAD(0x369c, PIN_OUTPUT | MUX_MODE5) /* xref_clk2.atl_clk2 */
- >;
- };
-
- mcasp3_pins: pinmux_mcasp3_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_aclkx */
- DRA7XX_CORE_IOPAD(0x3728, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_fsx */
- DRA7XX_CORE_IOPAD(0x372c, PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr0 */
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE0) /* mcasp3_axr1 */
- >;
- };
-
- mcasp3_sleep_pins: pinmux_mcasp3_sleep_pins {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x3724, PIN_INPUT_PULLDOWN | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3728, PIN_INPUT_PULLDOWN | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x372c, PIN_INPUT_PULLDOWN | MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3730, PIN_INPUT_PULLDOWN | MUX_MODE15)
- >;
- };
};
&i2c1 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
clock-frequency = <400000>;
tps65917: tps65917 at 58 {
compatible = "ti,tps65917";
reg = <0x58>;
- pinctrl-names = "default";
- pinctrl-0 = <&tps65917_pins_default>;
-
interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
interrupt-controller;
#interrupt-cells = <2>;
@@ -423,8 +311,6 @@
&i2c5 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&i2c5_pins>;
clock-frequency = <400000>;
pcf_hdmi: pcf8575 at 26 {
@@ -462,8 +348,6 @@
&gpmc {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&nand_default>;
ranges = <0 0 0x08000000 0x01000000>; /* minimum GPMC partition = 16MB */
nand at 0,0 {
/* To use NAND, DIP switch SW5 must be set like so:
@@ -566,14 +450,10 @@
&usb1 {
dr_mode = "peripheral";
- pinctrl-names = "default";
- pinctrl-0 = <&usb1_pins>;
};
&usb2 {
dr_mode = "host";
- pinctrl-names = "default";
- pinctrl-0 = <&usb2_pins>;
};
&mmc1 {
@@ -603,71 +483,8 @@
max-frequency = <192000000>;
};
-&dra7_pmx_core {
- cpsw_default: cpsw_default {
- pinctrl-single,pins = <
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, PIN_OUTPUT | MUX_MODE3) /* vin2a_d12.rgmii1_txc */
- DRA7XX_CORE_IOPAD(0x359c, PIN_OUTPUT | MUX_MODE3) /* vin2a_d13.rgmii1_tctl */
- DRA7XX_CORE_IOPAD(0x35a0, PIN_OUTPUT | MUX_MODE3) /* vin2a_d14.rgmii1_td3 */
- DRA7XX_CORE_IOPAD(0x35a4, PIN_OUTPUT | MUX_MODE3) /* vin2a_d15.rgmii1_td2 */
- DRA7XX_CORE_IOPAD(0x35a8, PIN_OUTPUT | MUX_MODE3) /* vin2a_d16.rgmii1_td1 */
- DRA7XX_CORE_IOPAD(0x35ac, PIN_OUTPUT | MUX_MODE3) /* vin2a_d17.rgmii1_td0 */
- DRA7XX_CORE_IOPAD(0x35b0, PIN_INPUT | MUX_MODE3) /* vin2a_d18.rgmii1_rclk */
- DRA7XX_CORE_IOPAD(0x35b4, PIN_INPUT | MUX_MODE3) /* vin2a_d19.rgmii1_rctl */
- DRA7XX_CORE_IOPAD(0x35b8, PIN_INPUT | MUX_MODE3) /* vin2a_d20.rgmii1_rd3 */
- DRA7XX_CORE_IOPAD(0x35bc, PIN_INPUT | MUX_MODE3) /* vin2a_d21.rgmii1_rd2 */
- DRA7XX_CORE_IOPAD(0x35c0, PIN_INPUT | MUX_MODE3) /* vin2a_d22.rgmii1_rd1 */
- DRA7XX_CORE_IOPAD(0x35c4, PIN_INPUT | MUX_MODE3) /* vin2a_d23.rgmii1_rd0 */
- >;
-
- };
-
- cpsw_sleep: cpsw_sleep {
- pinctrl-single,pins = <
- /* Slave 2 */
- DRA7XX_CORE_IOPAD(0x3598, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x359c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a4, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35a8, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35ac, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b4, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35b8, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35bc, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c0, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x35c4, MUX_MODE15)
- >;
- };
-
- davinci_mdio_default: davinci_mdio_default {
- pinctrl-single,pins = <
- /* MDIO */
- DRA7XX_CORE_IOPAD(0x363c, PIN_OUTPUT_PULLUP | MUX_MODE0) /* mdio_d.mdio_d */
- DRA7XX_CORE_IOPAD(0x3640, PIN_INPUT_PULLUP | MUX_MODE0) /* mdio_clk.mdio_clk */
- >;
- };
-
- davinci_mdio_sleep: davinci_mdio_sleep {
- pinctrl-single,pins = <
- DRA7XX_CORE_IOPAD(0x363c, MUX_MODE15)
- DRA7XX_CORE_IOPAD(0x3640, MUX_MODE15)
- >;
- };
-};
-
&mac {
status = "okay";
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&cpsw_default>;
- pinctrl-1 = <&cpsw_sleep>;
-};
-
-&davinci_mdio {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&davinci_mdio_default>;
- pinctrl-1 = <&davinci_mdio_sleep>;
};
&dcan1 {
@@ -748,9 +565,6 @@
&hdmi {
status = "ok";
- pinctrl-names = "default";
- pinctrl-0 = <&hdmi_pins>;
-
port {
hdmi_out: endpoint {
remote-endpoint = <&tpd12s015_in>;
@@ -759,9 +573,6 @@
};
&atl {
- pinctrl-names = "default";
- pinctrl-0 = <&atl_pins>;
-
assigned-clocks = <&abe_dpll_sys_clk_mux>,
<&atl_gfclk_mux>,
<&dpll_abe_ck>,
@@ -780,9 +591,6 @@
&mcasp3 {
#sound-dai-cells = <0>;
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&mcasp3_pins>;
- pinctrl-1 = <&mcasp3_sleep_pins>;
assigned-clocks = <&mcasp3_ahclkx_mux>;
assigned-clock-parents = <&atl_clkin2_ck>;
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 2/9] ARM: dra72-evm: Fix modelling of regulators
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 1/9] ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869 Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917 Lokesh Vutla
` (7 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
Add proper description of input voltage regulators and update the voltage
rail map for all the regulators.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/boot/dts/dra72-evm-common.dtsi | 48 +++++++++++++++++++++++++++++++++
1 file changed, 48 insertions(+)
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index 3c02612..8537b6a 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -18,11 +18,47 @@
display0 = &hdmi0;
};
+ evm_12v0: fixedregulator-evm12v0 {
+ /* main supply */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_12v0";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ evm_5v0: fixedregulator-evm5v0 {
+ /* Output 1 of TPS43351QDAPRQ1 */
+ compatible = "regulator-fixed";
+ regulator-name = "evm_5v0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vsys_3v3: fixedregulator-vsys3v3 {
+ /* Output 2 of TPS43351QDAPRQ1 */
+ compatible = "regulator-fixed";
+ regulator-name = "vsys_3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&evm_12v0>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
evm_3v3_sw: fixedregulator-evm_3v3 {
+ /* TPS22965DSG */
compatible = "regulator-fixed";
regulator-name = "evm_3v3";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ vin-supply = <&vsys_3v3>;
+ regulator-always-on;
+ regulator-boot-on;
};
aic_dvdd: fixedregulator-aic_dvdd {
@@ -39,6 +75,7 @@
regulator-name = "evm_3v3_sd";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+ vin-supply = <&evm_3v3_sw>;
enable-active-high;
gpio = <&pcf_gpio_21 5 GPIO_ACTIVE_HIGH>;
};
@@ -190,6 +227,17 @@
tps65917_pmic {
compatible = "ti,tps65917-pmic";
+ smps1-in-supply = <&vsys_3v3>;
+ smps2-in-supply = <&vsys_3v3>;
+ smps3-in-supply = <&vsys_3v3>;
+ smps4-in-supply = <&vsys_3v3>;
+ smps5-in-supply = <&vsys_3v3>;
+ ldo1-in-supply = <&vsys_3v3>;
+ ldo2-in-supply = <&vsys_3v3>;
+ ldo3-in-supply = <&vsys_3v3>;
+ ldo4-in-supply = <&evm_5v0>;
+ ldo5-in-supply = <&vsys_3v3>;
+
tps65917_regulators: regulators {
smps1_reg: smps1 {
/* VDD_MPU */
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 1/9] ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869 Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 2/9] ARM: dra72-evm: Fix modelling of regulators Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-12-13 12:40 ` Roger Quadros
2016-10-21 10:38 ` [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply Lokesh Vutla
` (6 subsequent siblings)
9 siblings, 1 reply; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
dra72-evm-common.dtsi consolidates dra72-evm.dts and dra72-evm-revc.dts
which also include tps65917 pmic support as both the evms uses the same
pmic. But, dra71-evm has mostly similar features with a different pmic.
In order to exploit dra72-evm-common.dtsi, creating a separate dtsi
for tps65915 support and including it in respective board files.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/boot/dts/dra72-evm-common.dtsi | 128 ----------------------------
arch/arm/boot/dts/dra72-evm-revc.dts | 21 +++--
arch/arm/boot/dts/dra72-evm-tps65917.dtsi | 134 ++++++++++++++++++++++++++++++
arch/arm/boot/dts/dra72-evm.dts | 14 ++--
4 files changed, 154 insertions(+), 143 deletions(-)
create mode 100644 arch/arm/boot/dts/dra72-evm-tps65917.dtsi
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index 8537b6a..9903ac7 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -214,123 +214,6 @@
status = "okay";
clock-frequency = <400000>;
- tps65917: tps65917 at 58 {
- compatible = "ti,tps65917";
- reg = <0x58>;
-
- interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
- interrupt-controller;
- #interrupt-cells = <2>;
-
- ti,system-power-controller;
-
- tps65917_pmic {
- compatible = "ti,tps65917-pmic";
-
- smps1-in-supply = <&vsys_3v3>;
- smps2-in-supply = <&vsys_3v3>;
- smps3-in-supply = <&vsys_3v3>;
- smps4-in-supply = <&vsys_3v3>;
- smps5-in-supply = <&vsys_3v3>;
- ldo1-in-supply = <&vsys_3v3>;
- ldo2-in-supply = <&vsys_3v3>;
- ldo3-in-supply = <&vsys_3v3>;
- ldo4-in-supply = <&evm_5v0>;
- ldo5-in-supply = <&vsys_3v3>;
-
- tps65917_regulators: regulators {
- smps1_reg: smps1 {
- /* VDD_MPU */
- regulator-name = "smps1";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps2_reg: smps2 {
- /* VDD_CORE */
- regulator-name = "smps2";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1150000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- smps3_reg: smps3 {
- /* VDD_GPU IVA DSPEVE */
- regulator-name = "smps3";
- regulator-min-microvolt = <850000>;
- regulator-max-microvolt = <1250000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- smps4_reg: smps4 {
- /* VDDS1V8 */
- regulator-name = "smps4";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- smps5_reg: smps5 {
- /* VDD_DDR */
- regulator-name = "smps5";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo1_reg: ldo1 {
- /* LDO1_OUT --> SDIO */
- regulator-name = "ldo1";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-boot-on;
- regulator-allow-bypass;
- };
-
- ldo3_reg: ldo3 {
- /* VDDA_1V8_PHY */
- regulator-name = "ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-boot-on;
- regulator-always-on;
- };
-
- ldo5_reg: ldo5 {
- /* VDDA_1V8_PLL */
- regulator-name = "ldo5";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
- };
-
- ldo4_reg: ldo4 {
- /* VDDA_3V_USB: VDDA_USBHS33 */
- regulator-name = "ldo4";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-boot-on;
- };
- };
- };
-
- tps65917_power_button {
- compatible = "ti,palmas-pwrbutton";
- interrupt-parent = <&tps65917>;
- interrupts = <1 IRQ_TYPE_NONE>;
- wakeup-source;
- ti,palmas-long-press-seconds = <6>;
- };
- };
-
pcf_gpio_21: gpio at 21 {
compatible = "ti,pcf8575", "nxp,pcf8575";
reg = <0x21>;
@@ -480,14 +363,6 @@
};
};
-&usb2_phy1 {
- phy-supply = <&ldo4_reg>;
-};
-
-&usb2_phy2 {
- phy-supply = <&ldo4_reg>;
-};
-
&omap_dwc3_1 {
extcon = <&extcon_usb1>;
};
@@ -509,7 +384,6 @@
pinctrl-names = "default";
pinctrl-0 = <&mmc1_pins_default>;
vmmc-supply = <&evm_3v3_sd>;
- vmmc_aux-supply = <&ldo1_reg>;
bus-width = <4>;
/*
* SDCD signal is not being used here - using the fact that GPIO mode
@@ -606,8 +480,6 @@
&dss {
status = "ok";
-
- vdda_video-supply = <&ldo5_reg>;
};
&hdmi {
diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts
index 064b322..4ea2a0c 100644
--- a/arch/arm/boot/dts/dra72-evm-revc.dts
+++ b/arch/arm/boot/dts/dra72-evm-revc.dts
@@ -17,17 +17,22 @@
};
};
-&tps65917_regulators {
- ldo2_reg: ldo2 {
- /* LDO2_OUT --> VDDA_1V8_PHY2 */
- regulator-name = "ldo2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- regulator-boot-on;
+&i2c1 {
+ tps65917: tps65917 at 58 {
+ reg = <0x58>;
+
+ interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
};
};
+#include "dra72-evm-tps65917.dtsi"
+
+&ldo2_reg {
+ /* LDO2_OUT --> VDDA_1V8_PHY2 */
+ regulator-always-on;
+ regulator-boot-on;
+};
+
&hdmi {
vdda-supply = <&ldo2_reg>;
};
diff --git a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
new file mode 100644
index 0000000..ee6dac4
--- /dev/null
+++ b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
@@ -0,0 +1,134 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/tps65917-q1.pdf
+ */
+
+&tps65917 {
+ compatible = "ti,tps65917";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ ti,system-power-controller;
+
+ tps65917_pmic {
+ compatible = "ti,tps65917-pmic";
+
+ smps1-in-supply = <&vsys_3v3>;
+ smps2-in-supply = <&vsys_3v3>;
+ smps3-in-supply = <&vsys_3v3>;
+ smps4-in-supply = <&vsys_3v3>;
+ smps5-in-supply = <&vsys_3v3>;
+ ldo1-in-supply = <&vsys_3v3>;
+ ldo2-in-supply = <&vsys_3v3>;
+ ldo3-in-supply = <&vsys_3v3>;
+ ldo4-in-supply = <&evm_5v0>;
+ ldo5-in-supply = <&vsys_3v3>;
+
+ tps65917_regulators: regulators {
+ smps1_reg: smps1 {
+ /* VDD_MPU */
+ regulator-name = "smps1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps2_reg: smps2 {
+ /* VDD_CORE */
+ regulator-name = "smps2";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ smps3_reg: smps3 {
+ /* VDD_GPU IVA DSPEVE */
+ regulator-name = "smps3";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ smps4_reg: smps4 {
+ /* VDDS1V8 */
+ regulator-name = "smps4";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ smps5_reg: smps5 {
+ /* VDD_DDR */
+ regulator-name = "smps5";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ /* LDO1_OUT --> SDIO */
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-allow-bypass;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-bypass;
+ };
+
+ ldo3_reg: ldo3 {
+ /* VDDA_1V8_PHY */
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo5_reg: ldo5 {
+ /* VDDA_1V8_PLL */
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo4_reg: ldo4 {
+ /* VDDA_3V_USB: VDDA_USBHS33 */
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ tps65917_power_button {
+ compatible = "ti,palmas-pwrbutton";
+ interrupt-parent = <&tps65917>;
+ interrupts = <1 IRQ_TYPE_NONE>;
+ wakeup-source;
+ ti,palmas-long-press-seconds = <6>;
+ };
+};
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index e3a9b69..cd9c4ff 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -15,16 +15,16 @@
};
};
-&tps65917_regulators {
- ldo2_reg: ldo2 {
- /* LDO2_OUT --> TP1017 (UNUSED) */
- regulator-name = "ldo2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-allow-bypass;
+&i2c1 {
+ tps65917: tps65917 at 58 {
+ reg = <0x58>;
+
+ interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
};
};
+#include "dra72-evm-tps65917.dtsi"
+
&hdmi {
vdda-supply = <&ldo3_reg>;
};
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917
2016-10-21 10:38 ` [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917 Lokesh Vutla
@ 2016-12-13 12:40 ` Roger Quadros
2016-12-13 13:08 ` Lokesh Vutla
0 siblings, 1 reply; 19+ messages in thread
From: Roger Quadros @ 2016-12-13 12:40 UTC (permalink / raw)
To: linux-arm-kernel
+Tomi, Kishon, Carlos
Hi,
On 21/10/16 13:38, Lokesh Vutla wrote:
> dra72-evm-common.dtsi consolidates dra72-evm.dts and dra72-evm-revc.dts
> which also include tps65917 pmic support as both the evms uses the same
> pmic. But, dra71-evm has mostly similar features with a different pmic.
> In order to exploit dra72-evm-common.dtsi, creating a separate dtsi
> for tps65915 support and including it in respective board files.
>
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
> arch/arm/boot/dts/dra72-evm-common.dtsi | 128 ----------------------------
> arch/arm/boot/dts/dra72-evm-revc.dts | 21 +++--
> arch/arm/boot/dts/dra72-evm-tps65917.dtsi | 134 ++++++++++++++++++++++++++++++
> arch/arm/boot/dts/dra72-evm.dts | 14 ++--
> 4 files changed, 154 insertions(+), 143 deletions(-)
> create mode 100644 arch/arm/boot/dts/dra72-evm-tps65917.dtsi
>
This patch breaks USB XHCI and boot on dra72-evm (both revC and non revC)
I'll explain why below.
[ 13.625167] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
[ 13.632557] pgd = ede10000
[ 13.635390] [00000000] *pgd=00000000
[ 13.639145] Internal error: : 1406 [#1] SMP ARM
[ 13.643893] Modules linked in: xhci_plat_hcd(+) xhci_hcd usbcore omapfb dwc3 cfbfillrect snd_soc_davinci_mcasp cfbimgblt cfbcopyarea udc_core connector_hdmi encoder_tpd12s015 snd_soc_edma m25p80 snd_soc_simpe
[ 13.695557] CPU: 0 PID: 440 Comm: modprobe Not tainted 4.9.0-rc1 #1050
[ 13.702399] Hardware name: Generic DRA72X (Flattened Device Tree)
[ 13.708786] task: edb5c040 task.stack: edd10000
[ 13.713540] PC is at _raw_spin_unlock_irqrestore+0x0/0x44
[ 13.719219] LR is at xhci_hub_control+0xc2c/0x15e0 [xhci_hcd]
[ 13.725242] pc : [<c07df718>] lr : [<bf486300>] psr: a0000093
[ 13.725242] sp : edd118c0 ip : c0e306b4 fp : 00000000
[ 13.737278] r10: 00000000 r9 : 60000013 r8 : edf28218
[ 13.742753] r7 : edf28000 r6 : 00000000 r5 : 00000000 r4 : edf2a000
[ 13.749593] r3 : 00000000 r2 : 00000000 r1 : 60000013 r0 : edf28218
> diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
> index 8537b6a..9903ac7 100644
> --- a/arch/arm/boot/dts/dra72-evm-common.dtsi
> +++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
> @@ -214,123 +214,6 @@
> status = "okay";
> clock-frequency = <400000>;
>
> - tps65917: tps65917 at 58 {
> - compatible = "ti,tps65917";
> - reg = <0x58>;
> -
> - interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
> - interrupt-controller;
> - #interrupt-cells = <2>;
> -
> - ti,system-power-controller;
> -
> - tps65917_pmic {
> - compatible = "ti,tps65917-pmic";
> -
> - smps1-in-supply = <&vsys_3v3>;
> - smps2-in-supply = <&vsys_3v3>;
> - smps3-in-supply = <&vsys_3v3>;
> - smps4-in-supply = <&vsys_3v3>;
> - smps5-in-supply = <&vsys_3v3>;
> - ldo1-in-supply = <&vsys_3v3>;
> - ldo2-in-supply = <&vsys_3v3>;
> - ldo3-in-supply = <&vsys_3v3>;
> - ldo4-in-supply = <&evm_5v0>;
> - ldo5-in-supply = <&vsys_3v3>;
> -
> - tps65917_regulators: regulators {
> - smps1_reg: smps1 {
> - /* VDD_MPU */
> - regulator-name = "smps1";
> - regulator-min-microvolt = <850000>;
> - regulator-max-microvolt = <1250000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> -
> - smps2_reg: smps2 {
> - /* VDD_CORE */
> - regulator-name = "smps2";
> - regulator-min-microvolt = <850000>;
> - regulator-max-microvolt = <1150000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - smps3_reg: smps3 {
> - /* VDD_GPU IVA DSPEVE */
> - regulator-name = "smps3";
> - regulator-min-microvolt = <850000>;
> - regulator-max-microvolt = <1250000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - smps4_reg: smps4 {
> - /* VDDS1V8 */
> - regulator-name = "smps4";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> -
> - smps5_reg: smps5 {
> - /* VDD_DDR */
> - regulator-name = "smps5";
> - regulator-min-microvolt = <1350000>;
> - regulator-max-microvolt = <1350000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo1_reg: ldo1 {
> - /* LDO1_OUT --> SDIO */
> - regulator-name = "ldo1";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - regulator-boot-on;
> - regulator-allow-bypass;
> - };
> -
> - ldo3_reg: ldo3 {
> - /* VDDA_1V8_PHY */
> - regulator-name = "ldo3";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - ldo5_reg: ldo5 {
> - /* VDDA_1V8_PLL */
> - regulator-name = "ldo5";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> - };
> -
> - ldo4_reg: ldo4 {
> - /* VDDA_3V_USB: VDDA_USBHS33 */
> - regulator-name = "ldo4";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - };
> - };
> - };
> -
> - tps65917_power_button {
> - compatible = "ti,palmas-pwrbutton";
> - interrupt-parent = <&tps65917>;
> - interrupts = <1 IRQ_TYPE_NONE>;
> - wakeup-source;
> - ti,palmas-long-press-seconds = <6>;
> - };
> - };
> -
> pcf_gpio_21: gpio at 21 {
> compatible = "ti,pcf8575", "nxp,pcf8575";
> reg = <0x21>;
> @@ -480,14 +363,6 @@
> };
> };
>
> -&usb2_phy1 {
> - phy-supply = <&ldo4_reg>;
> -};
> -
> -&usb2_phy2 {
> - phy-supply = <&ldo4_reg>;
> -};
> -
You remove this here but don't add them in the board dts files.
> &omap_dwc3_1 {
> extcon = <&extcon_usb1>;
> };
> @@ -509,7 +384,6 @@
> pinctrl-names = "default";
> pinctrl-0 = <&mmc1_pins_default>;
> vmmc-supply = <&evm_3v3_sd>;
> - vmmc_aux-supply = <&ldo1_reg>;
What about this?
> bus-width = <4>;
> /*
> * SDCD signal is not being used here - using the fact that GPIO mode
> @@ -606,8 +480,6 @@
>
> &dss {
> status = "ok";
> -
> - vdda_video-supply = <&ldo5_reg>;
and this?
> };
>
> &hdmi {
> diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts
> index 064b322..4ea2a0c 100644
> --- a/arch/arm/boot/dts/dra72-evm-revc.dts
> +++ b/arch/arm/boot/dts/dra72-evm-revc.dts
> @@ -17,17 +17,22 @@
> };
> };
>
> -&tps65917_regulators {
> - ldo2_reg: ldo2 {
> - /* LDO2_OUT --> VDDA_1V8_PHY2 */
> - regulator-name = "ldo2";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - regulator-boot-on;
> +&i2c1 {
> + tps65917: tps65917 at 58 {
> + reg = <0x58>;
> +
> + interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
> };
> };
>
> +#include "dra72-evm-tps65917.dtsi"
> +
> +&ldo2_reg {
> + /* LDO2_OUT --> VDDA_1V8_PHY2 */
> + regulator-always-on;
> + regulator-boot-on;
> +};
> +
Here you need to add the usb2_phy1 & 2 supplies.
> &hdmi {
> vdda-supply = <&ldo2_reg>;
> };
> diff --git a/arch/arm/boot/dts/dra72-evm-tps65917.dtsi b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
> new file mode 100644
> index 0000000..ee6dac4
> --- /dev/null
> +++ b/arch/arm/boot/dts/dra72-evm-tps65917.dtsi
> @@ -0,0 +1,134 @@
> +/*
> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +/*
> + * Integrated Power Management Chip
> + * http://www.ti.com/lit/ds/symlink/tps65917-q1.pdf
> + */
> +
> +&tps65917 {
> + compatible = "ti,tps65917";
> +
> + interrupt-controller;
> + #interrupt-cells = <2>;
> +
> + ti,system-power-controller;
> +
> + tps65917_pmic {
> + compatible = "ti,tps65917-pmic";
> +
> + smps1-in-supply = <&vsys_3v3>;
> + smps2-in-supply = <&vsys_3v3>;
> + smps3-in-supply = <&vsys_3v3>;
> + smps4-in-supply = <&vsys_3v3>;
> + smps5-in-supply = <&vsys_3v3>;
> + ldo1-in-supply = <&vsys_3v3>;
> + ldo2-in-supply = <&vsys_3v3>;
> + ldo3-in-supply = <&vsys_3v3>;
> + ldo4-in-supply = <&evm_5v0>;
> + ldo5-in-supply = <&vsys_3v3>;
> +
> + tps65917_regulators: regulators {
> + smps1_reg: smps1 {
> + /* VDD_MPU */
> + regulator-name = "smps1";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps2_reg: smps2 {
> + /* VDD_CORE */
> + regulator-name = "smps2";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1150000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + smps3_reg: smps3 {
> + /* VDD_GPU IVA DSPEVE */
> + regulator-name = "smps3";
> + regulator-min-microvolt = <850000>;
> + regulator-max-microvolt = <1250000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + smps4_reg: smps4 {
> + /* VDDS1V8 */
> + regulator-name = "smps4";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + smps5_reg: smps5 {
> + /* VDD_DDR */
> + regulator-name = "smps5";
> + regulator-min-microvolt = <1350000>;
> + regulator-max-microvolt = <1350000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo1_reg: ldo1 {
> + /* LDO1_OUT --> SDIO */
> + regulator-name = "ldo1";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-allow-bypass;
> + };
> +
> + ldo2_reg: ldo2 {
> + regulator-name = "ldo2";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-allow-bypass;
> + };
> +
> + ldo3_reg: ldo3 {
> + /* VDDA_1V8_PHY */
> + regulator-name = "ldo3";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-boot-on;
> + regulator-always-on;
> + };
> +
> + ldo5_reg: ldo5 {
> + /* VDDA_1V8_PLL */
> + regulator-name = "ldo5";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + ldo4_reg: ldo4 {
> + /* VDDA_3V_USB: VDDA_USBHS33 */
> + regulator-name = "ldo4";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> + };
> + };
> + };
> +
> + tps65917_power_button {
> + compatible = "ti,palmas-pwrbutton";
> + interrupt-parent = <&tps65917>;
> + interrupts = <1 IRQ_TYPE_NONE>;
> + wakeup-source;
> + ti,palmas-long-press-seconds = <6>;
> + };
> +};
> diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
> index e3a9b69..cd9c4ff 100644
> --- a/arch/arm/boot/dts/dra72-evm.dts
> +++ b/arch/arm/boot/dts/dra72-evm.dts
> @@ -15,16 +15,16 @@
> };
> };
>
> -&tps65917_regulators {
> - ldo2_reg: ldo2 {
> - /* LDO2_OUT --> TP1017 (UNUSED) */
> - regulator-name = "ldo2";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-allow-bypass;
> +&i2c1 {
> + tps65917: tps65917 at 58 {
> + reg = <0x58>;
> +
> + interrupts = <GIC_SPI 2 IRQ_TYPE_NONE>; /* IRQ_SYS_1N */
> };
> };
>
> +#include "dra72-evm-tps65917.dtsi"
> +
> &hdmi {
> vdda-supply = <&ldo3_reg>;
> };
>
Here as well you need to add the usb2_phy1 & 2 supplies.
We probably need to add dss and mmc supplies as well to both the board dts files?
cheers,
-roger
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917
2016-12-13 12:40 ` Roger Quadros
@ 2016-12-13 13:08 ` Lokesh Vutla
2016-12-13 14:55 ` Roger Quadros
0 siblings, 1 reply; 19+ messages in thread
From: Lokesh Vutla @ 2016-12-13 13:08 UTC (permalink / raw)
To: linux-arm-kernel
On Tuesday 13 December 2016 06:10 PM, Roger Quadros wrote:
> +Tomi, Kishon, Carlos
>
> Hi,
>
> On 21/10/16 13:38, Lokesh Vutla wrote:
>> dra72-evm-common.dtsi consolidates dra72-evm.dts and dra72-evm-revc.dts
>> which also include tps65917 pmic support as both the evms uses the same
>> pmic. But, dra71-evm has mostly similar features with a different pmic.
>> In order to exploit dra72-evm-common.dtsi, creating a separate dtsi
>> for tps65915 support and including it in respective board files.
>>
>> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
>> ---
>> arch/arm/boot/dts/dra72-evm-common.dtsi | 128 ----------------------------
>> arch/arm/boot/dts/dra72-evm-revc.dts | 21 +++--
>> arch/arm/boot/dts/dra72-evm-tps65917.dtsi | 134 ++++++++++++++++++++++++++++++
>> arch/arm/boot/dts/dra72-evm.dts | 14 ++--
>> 4 files changed, 154 insertions(+), 143 deletions(-)
>> create mode 100644 arch/arm/boot/dts/dra72-evm-tps65917.dtsi
>>
>
> This patch breaks USB XHCI and boot on dra72-evm (both revC and non revC)
>
> I'll explain why below.
>
> [ 13.625167] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
> [ 13.632557] pgd = ede10000
> [ 13.635390] [00000000] *pgd=00000000
> [ 13.639145] Internal error: : 1406 [#1] SMP ARM
> [ 13.643893] Modules linked in: xhci_plat_hcd(+) xhci_hcd usbcore omapfb dwc3 cfbfillrect snd_soc_davinci_mcasp cfbimgblt cfbcopyarea udc_core connector_hdmi encoder_tpd12s015 snd_soc_edma m25p80 snd_soc_simpe
> [ 13.695557] CPU: 0 PID: 440 Comm: modprobe Not tainted 4.9.0-rc1 #1050
> [ 13.702399] Hardware name: Generic DRA72X (Flattened Device Tree)
> [ 13.708786] task: edb5c040 task.stack: edd10000
> [ 13.713540] PC is at _raw_spin_unlock_irqrestore+0x0/0x44
> [ 13.719219] LR is at xhci_hub_control+0xc2c/0x15e0 [xhci_hcd]
> [ 13.725242] pc : [<c07df718>] lr : [<bf486300>] psr: a0000093
> [ 13.725242] sp : edd118c0 ip : c0e306b4 fp : 00000000
> [ 13.737278] r10: 00000000 r9 : 60000013 r8 : edf28218
> [ 13.742753] r7 : edf28000 r6 : 00000000 r5 : 00000000 r4 : edf2a000
> [ 13.749593] r3 : 00000000 r2 : 00000000 r1 : 60000013 r0 : edf28218
Hmm.. Thanks for catching it. I remember it was booting when I tested,
not sure how I missed this :(. usb2_phy1 & 2, mmc and dss supplies needs
to be added in dra72-evm-tps65917.dtsi file.
Tony,
Do you want me to resend this patch or fixup patch on top of this?
Thanks and regards,
Lokesh
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917
2016-12-13 13:08 ` Lokesh Vutla
@ 2016-12-13 14:55 ` Roger Quadros
0 siblings, 0 replies; 19+ messages in thread
From: Roger Quadros @ 2016-12-13 14:55 UTC (permalink / raw)
To: linux-arm-kernel
Lokesh,
On 13/12/16 15:08, Lokesh Vutla wrote:
>
>
> On Tuesday 13 December 2016 06:10 PM, Roger Quadros wrote:
>> +Tomi, Kishon, Carlos
>>
>> Hi,
>>
>> On 21/10/16 13:38, Lokesh Vutla wrote:
>>> dra72-evm-common.dtsi consolidates dra72-evm.dts and dra72-evm-revc.dts
>>> which also include tps65917 pmic support as both the evms uses the same
>>> pmic. But, dra71-evm has mostly similar features with a different pmic.
>>> In order to exploit dra72-evm-common.dtsi, creating a separate dtsi
>>> for tps65915 support and including it in respective board files.
>>>
>>> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
>>> ---
>>> arch/arm/boot/dts/dra72-evm-common.dtsi | 128 ----------------------------
>>> arch/arm/boot/dts/dra72-evm-revc.dts | 21 +++--
>>> arch/arm/boot/dts/dra72-evm-tps65917.dtsi | 134 ++++++++++++++++++++++++++++++
>>> arch/arm/boot/dts/dra72-evm.dts | 14 ++--
>>> 4 files changed, 154 insertions(+), 143 deletions(-)
>>> create mode 100644 arch/arm/boot/dts/dra72-evm-tps65917.dtsi
>>>
>>
>> This patch breaks USB XHCI and boot on dra72-evm (both revC and non revC)
>>
>> I'll explain why below.
>>
>> [ 13.625167] Unhandled fault: imprecise external abort (0x1406) at 0x00000000
>> [ 13.632557] pgd = ede10000
>> [ 13.635390] [00000000] *pgd=00000000
>> [ 13.639145] Internal error: : 1406 [#1] SMP ARM
>> [ 13.643893] Modules linked in: xhci_plat_hcd(+) xhci_hcd usbcore omapfb dwc3 cfbfillrect snd_soc_davinci_mcasp cfbimgblt cfbcopyarea udc_core connector_hdmi encoder_tpd12s015 snd_soc_edma m25p80 snd_soc_simpe
>> [ 13.695557] CPU: 0 PID: 440 Comm: modprobe Not tainted 4.9.0-rc1 #1050
>> [ 13.702399] Hardware name: Generic DRA72X (Flattened Device Tree)
>> [ 13.708786] task: edb5c040 task.stack: edd10000
>> [ 13.713540] PC is at _raw_spin_unlock_irqrestore+0x0/0x44
>> [ 13.719219] LR is at xhci_hub_control+0xc2c/0x15e0 [xhci_hcd]
>> [ 13.725242] pc : [<c07df718>] lr : [<bf486300>] psr: a0000093
>> [ 13.725242] sp : edd118c0 ip : c0e306b4 fp : 00000000
>> [ 13.737278] r10: 00000000 r9 : 60000013 r8 : edf28218
>> [ 13.742753] r7 : edf28000 r6 : 00000000 r5 : 00000000 r4 : edf2a000
>> [ 13.749593] r3 : 00000000 r2 : 00000000 r1 : 60000013 r0 : edf28218
>
> Hmm.. Thanks for catching it. I remember it was booting when I tested,
> not sure how I missed this :(. usb2_phy1 & 2, mmc and dss supplies needs
> to be added in dra72-evm-tps65917.dtsi file.
OK.
>
> Tony,
> Do you want me to resend this patch or fixup patch on top of this?
In case you send a new patch. please add
Reported-by: Carlos Hernandez <ceh@ti.com>
Thanks.
cheers,
-roger
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (2 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 3/9] ARM: dts: dra72: Add separate dtsi for tps65917 Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-30 20:41 ` Rob Herring
2016-10-21 10:38 ` [PATCH v2 5/9] ARM: OMAP2+: board-generic: add support for DRA71x family Lokesh Vutla
` (5 subsequent siblings)
9 siblings, 1 reply; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
In order to have a proper topology of regulators for a platform, each
registering regulator needs to populate supply_name field for identifying
its supply's name. Add supply_name field for lp873x regulators.
Cc: Lee Jones <lee.jones@linaro.org>
Cc: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
drivers/regulator/lp873x-regulator.c | 1 +
2 files changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt
index 52766c2..998837a 100644
--- a/Documentation/devicetree/bindings/mfd/lp873x.txt
+++ b/Documentation/devicetree/bindings/mfd/lp873x.txt
@@ -7,6 +7,9 @@ Required properties:
- #gpio-cells: Should be two. The first cell is the pin number and
the second cell is used to specify flags.
See ../gpio/gpio.txt for more information.
+ - xxx-in-supply: Phandle to parent supply node of each regulator
+ populated under regulators node. xxx should match
+ the supply_name populated in driver.
- regulators: List of child nodes that specify the regulator
initialization data.
Example:
@@ -17,6 +20,11 @@ pmic: lp8733 at 60 {
gpio-controller;
#gpio-cells = <2>;
+ buck0-in-supply = <&vsys_3v3>;
+ buck1-in-supply = <&vsys_3v3>;
+ ldo0-in-supply = <&vsys_3v3>;
+ ldo1-in-supply = <&vsys_3v3>;
+
regulators {
lp8733_buck0: buck0 {
regulator-name = "lp8733-buck0";
diff --git a/drivers/regulator/lp873x-regulator.c b/drivers/regulator/lp873x-regulator.c
index e504b91..70e3df6 100644
--- a/drivers/regulator/lp873x-regulator.c
+++ b/drivers/regulator/lp873x-regulator.c
@@ -24,6 +24,7 @@
[_id] = { \
.desc = { \
.name = _name, \
+ .supply_name = _of "-in", \
.id = _id, \
.of_match = of_match_ptr(_of), \
.regulators_node = of_match_ptr("regulators"),\
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply
2016-10-21 10:38 ` [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply Lokesh Vutla
@ 2016-10-30 20:41 ` Rob Herring
2016-11-02 5:28 ` Lokesh Vutla
0 siblings, 1 reply; 19+ messages in thread
From: Rob Herring @ 2016-10-30 20:41 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Oct 21, 2016 at 04:08:36PM +0530, Lokesh Vutla wrote:
> In order to have a proper topology of regulators for a platform, each
> registering regulator needs to populate supply_name field for identifying
> its supply's name. Add supply_name field for lp873x regulators.
>
> Cc: Lee Jones <lee.jones@linaro.org>
> Cc: Keerthy <j-keerthy@ti.com>
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
> Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
> drivers/regulator/lp873x-regulator.c | 1 +
> 2 files changed, 9 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt
> index 52766c2..998837a 100644
> --- a/Documentation/devicetree/bindings/mfd/lp873x.txt
> +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt
> @@ -7,6 +7,9 @@ Required properties:
> - #gpio-cells: Should be two. The first cell is the pin number and
> the second cell is used to specify flags.
> See ../gpio/gpio.txt for more information.
> + - xxx-in-supply: Phandle to parent supply node of each regulator
> + populated under regulators node. xxx should match
> + the supply_name populated in driver.
The driver is irrelevant. This should reference a list in this document.
> - regulators: List of child nodes that specify the regulator
> initialization data.
> Example:
> @@ -17,6 +20,11 @@ pmic: lp8733 at 60 {
> gpio-controller;
> #gpio-cells = <2>;
>
> + buck0-in-supply = <&vsys_3v3>;
> + buck1-in-supply = <&vsys_3v3>;
> + ldo0-in-supply = <&vsys_3v3>;
> + ldo1-in-supply = <&vsys_3v3>;
> +
> regulators {
> lp8733_buck0: buck0 {
> regulator-name = "lp8733-buck0";
^ permalink raw reply [flat|nested] 19+ messages in thread* [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply
2016-10-30 20:41 ` Rob Herring
@ 2016-11-02 5:28 ` Lokesh Vutla
2016-11-09 18:26 ` Rob Herring
0 siblings, 1 reply; 19+ messages in thread
From: Lokesh Vutla @ 2016-11-02 5:28 UTC (permalink / raw)
To: linux-arm-kernel
On Monday 31 October 2016 02:11 AM, Rob Herring wrote:
> On Fri, Oct 21, 2016 at 04:08:36PM +0530, Lokesh Vutla wrote:
>> In order to have a proper topology of regulators for a platform, each
>> registering regulator needs to populate supply_name field for identifying
>> its supply's name. Add supply_name field for lp873x regulators.
>>
>> Cc: Lee Jones <lee.jones@linaro.org>
>> Cc: Keerthy <j-keerthy@ti.com>
>> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
>> ---
>> Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
>> drivers/regulator/lp873x-regulator.c | 1 +
>> 2 files changed, 9 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt
>> index 52766c2..998837a 100644
>> --- a/Documentation/devicetree/bindings/mfd/lp873x.txt
>> +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt
>> @@ -7,6 +7,9 @@ Required properties:
>> - #gpio-cells: Should be two. The first cell is the pin number and
>> the second cell is used to specify flags.
>> See ../gpio/gpio.txt for more information.
>> + - xxx-in-supply: Phandle to parent supply node of each regulator
>> + populated under regulators node. xxx should match
>> + the supply_name populated in driver.
>
> The driver is irrelevant. This should reference a list in this document.
okay. See if the below updated patch is fine.
-----------------------------8<----------------------------8<----------------------------
>From 666f925423fa35c7bfcc77fa3c883cbea5d8ef8e Mon Sep 17 00:00:00 2001
From: Lokesh Vutla <lokeshvutla@ti.com>
Date: Wed, 21 Sep 2016 11:50:49 +0530
Subject: [PATCH v3] regulator: lp873x: Add support for populating input
supply
In order to have a proper topology of regulators for a platform, each
registering regulator needs to populate supply_name field for identifying
its supply's name. Add supply_name field for lp873x regulators.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
drivers/regulator/lp873x-regulator.c | 1 +
2 files changed, 9 insertions(+)
diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt
b/Documentation/devicetree/bindings/mfd/lp873x.txt
index 52766c2..ae9cf39 100644
--- a/Documentation/devicetree/bindings/mfd/lp873x.txt
+++ b/Documentation/devicetree/bindings/mfd/lp873x.txt
@@ -7,6 +7,9 @@ Required properties:
- #gpio-cells: Should be two. The first cell is the pin number and
the second cell is used to specify flags.
See ../gpio/gpio.txt for more information.
+ - xxx-in-supply: Phandle to parent supply node of each regulator
+ populated under regulators node. xxx can be
+ buck0, buck1, ldo0 or ldo1.
- regulators: List of child nodes that specify the regulator
initialization data.
Example:
@@ -17,6 +20,11 @@ pmic: lp8733 at 60 {
gpio-controller;
#gpio-cells = <2>;
+ buck0-in-supply = <&vsys_3v3>;
+ buck1-in-supply = <&vsys_3v3>;
+ ldo0-in-supply = <&vsys_3v3>;
+ ldo1-in-supply = <&vsys_3v3>;
+
regulators {
lp8733_buck0: buck0 {
regulator-name = "lp8733-buck0";
diff --git a/drivers/regulator/lp873x-regulator.c
b/drivers/regulator/lp873x-regulator.c
index e504b91..70e3df6 100644
--- a/drivers/regulator/lp873x-regulator.c
+++ b/drivers/regulator/lp873x-regulator.c
@@ -24,6 +24,7 @@
[_id] = { \
.desc = { \
.name = _name, \
+ .supply_name = _of "-in", \
.id = _id, \
.of_match = of_match_ptr(_of), \
.regulators_node = of_match_ptr("regulators"),\
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply
2016-11-02 5:28 ` Lokesh Vutla
@ 2016-11-09 18:26 ` Rob Herring
2016-11-09 21:50 ` Tony Lindgren
0 siblings, 1 reply; 19+ messages in thread
From: Rob Herring @ 2016-11-09 18:26 UTC (permalink / raw)
To: linux-arm-kernel
On Wed, Nov 02, 2016 at 10:58:40AM +0530, Lokesh Vutla wrote:
>
>
> On Monday 31 October 2016 02:11 AM, Rob Herring wrote:
> > On Fri, Oct 21, 2016 at 04:08:36PM +0530, Lokesh Vutla wrote:
> >> In order to have a proper topology of regulators for a platform, each
> >> registering regulator needs to populate supply_name field for identifying
> >> its supply's name. Add supply_name field for lp873x regulators.
> >>
> >> Cc: Lee Jones <lee.jones@linaro.org>
> >> Cc: Keerthy <j-keerthy@ti.com>
> >> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> >> ---
> >> Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
> >> drivers/regulator/lp873x-regulator.c | 1 +
> >> 2 files changed, 9 insertions(+)
> >>
> >> diff --git a/Documentation/devicetree/bindings/mfd/lp873x.txt b/Documentation/devicetree/bindings/mfd/lp873x.txt
> >> index 52766c2..998837a 100644
> >> --- a/Documentation/devicetree/bindings/mfd/lp873x.txt
> >> +++ b/Documentation/devicetree/bindings/mfd/lp873x.txt
> >> @@ -7,6 +7,9 @@ Required properties:
> >> - #gpio-cells: Should be two. The first cell is the pin number and
> >> the second cell is used to specify flags.
> >> See ../gpio/gpio.txt for more information.
> >> + - xxx-in-supply: Phandle to parent supply node of each regulator
> >> + populated under regulators node. xxx should match
> >> + the supply_name populated in driver.
> >
> > The driver is irrelevant. This should reference a list in this document.
>
> okay. See if the below updated patch is fine.
>
> -----------------------------8<----------------------------8<----------------------------
> From 666f925423fa35c7bfcc77fa3c883cbea5d8ef8e Mon Sep 17 00:00:00 2001
> From: Lokesh Vutla <lokeshvutla@ti.com>
> Date: Wed, 21 Sep 2016 11:50:49 +0530
> Subject: [PATCH v3] regulator: lp873x: Add support for populating input
> supply
>
> In order to have a proper topology of regulators for a platform, each
> registering regulator needs to populate supply_name field for identifying
> its supply's name. Add supply_name field for lp873x regulators.
>
> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> ---
> Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
> drivers/regulator/lp873x-regulator.c | 1 +
> 2 files changed, 9 insertions(+)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply
2016-11-09 18:26 ` Rob Herring
@ 2016-11-09 21:50 ` Tony Lindgren
0 siblings, 0 replies; 19+ messages in thread
From: Tony Lindgren @ 2016-11-09 21:50 UTC (permalink / raw)
To: linux-arm-kernel
* Rob Herring <robh@kernel.org> [161109 11:26]:
> On Wed, Nov 02, 2016 at 10:58:40AM +0530, Lokesh Vutla wrote:
> > On Monday 31 October 2016 02:11 AM, Rob Herring wrote:
> > > On Fri, Oct 21, 2016 at 04:08:36PM +0530, Lokesh Vutla wrote:
> > >> In order to have a proper topology of regulators for a platform, each
> > >> registering regulator needs to populate supply_name field for identifying
> > >> its supply's name. Add supply_name field for lp873x regulators.
> > >>
> > >> Cc: Lee Jones <lee.jones@linaro.org>
> > >> Cc: Keerthy <j-keerthy@ti.com>
> > >> Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
> > >> ---
> > >> Documentation/devicetree/bindings/mfd/lp873x.txt | 8 ++++++++
> > >> drivers/regulator/lp873x-regulator.c | 1 +
...
> Acked-by: Rob Herring <robh@kernel.org>
Please send this patch separately to the regulator maintainer.
Thanks,
Tony
^ permalink raw reply [flat|nested] 19+ messages in thread
* [PATCH v2 5/9] ARM: OMAP2+: board-generic: add support for DRA71x family
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (3 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 4/9] regulator: lp873x: Add support for populating input supply Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 6/9] ARM: DRA7: hwmod: Do not register RTC on DRA71 Lokesh Vutla
` (4 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
DRA71x processor family is a derivative of DRA722 ES2.0 targetted for
infotainment systems.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
Documentation/devicetree/bindings/arm/omap/omap.txt | 6 ++++++
arch/arm/mach-omap2/board-generic.c | 1 +
2 files changed, 7 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/omap/omap.txt b/Documentation/devicetree/bindings/arm/omap/omap.txt
index f53e2ee..454b1be 100644
--- a/Documentation/devicetree/bindings/arm/omap/omap.txt
+++ b/Documentation/devicetree/bindings/arm/omap/omap.txt
@@ -86,6 +86,9 @@ SoCs:
- DRA722
compatible = "ti,dra722", "ti,dra72", "ti,dra7"
+- DRA718
+ compatible = "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7"
+
- AM5728
compatible = "ti,am5728", "ti,dra742", "ti,dra74", "ti,dra7"
@@ -181,6 +184,9 @@ Boards:
- DRA722 EVM: Software Development Board for DRA722
compatible = "ti,dra72-evm", "ti,dra722", "ti,dra72", "ti,dra7"
+- DRA718 EVM: Software Development Board for DRA718
+ compatible = "ti,dra718-evm", "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7"
+
- DM3730 Logic PD Torpedo + Wireless: Commercial System on Module with WiFi and Bluetooth
compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"
diff --git a/arch/arm/mach-omap2/board-generic.c b/arch/arm/mach-omap2/board-generic.c
index bab814d..981b23a 100644
--- a/arch/arm/mach-omap2/board-generic.c
+++ b/arch/arm/mach-omap2/board-generic.c
@@ -341,6 +341,7 @@ static const char *const dra72x_boards_compat[] __initconst = {
"ti,am5718",
"ti,am5716",
"ti,dra722",
+ "ti,dra718",
NULL,
};
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 6/9] ARM: DRA7: hwmod: Do not register RTC on DRA71
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (4 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 5/9] ARM: OMAP2+: board-generic: add support for DRA71x family Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 7/9] ARM: dts: Add support for dra718-evm Lokesh Vutla
` (3 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
From: Nishanth Menon <nm@ti.com>
RTC is not available on DRA71x, so accessing any of the RTC
register or clkctrl register will lead to a crash. So, do not
register RTC hwmod for DRA71x.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 10 +++++++++-
1 file changed, 9 insertions(+), 1 deletion(-)
diff --git a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
index 1ab7096..7f48577 100644
--- a/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
+++ b/arch/arm/mach-omap2/omap_hwmod_7xx_data.c
@@ -3845,7 +3845,6 @@ static struct omap_hwmod_ocp_if *dra7xx_hwmod_ocp_ifs[] __initdata = {
&dra7xx_l3_main_1__pciess2,
&dra7xx_l4_cfg__pciess2,
&dra7xx_l3_main_1__qspi,
- &dra7xx_l4_per3__rtcss,
&dra7xx_l4_cfg__sata,
&dra7xx_l4_cfg__smartreflex_core,
&dra7xx_l4_cfg__smartreflex_mpu,
@@ -3905,6 +3904,11 @@ static struct omap_hwmod_ocp_if *dra72x_hwmod_ocp_ifs[] __initdata = {
NULL,
};
+static struct omap_hwmod_ocp_if *dra74x_dra72x_hwmod_ocp_ifs[] __initdata = {
+ &dra7xx_l4_per3__rtcss,
+ NULL,
+};
+
int __init dra7xx_hwmod_init(void)
{
int ret;
@@ -3920,5 +3924,9 @@ int __init dra7xx_hwmod_init(void)
if (!ret && omap_type() == OMAP2_DEVICE_TYPE_GP)
ret = omap_hwmod_register_links(dra7xx_gp_hwmod_ocp_ifs);
+ /* now for the IPs *NOT* in dra71 */
+ if (!ret && !of_machine_is_compatible("ti,dra718"))
+ ret = omap_hwmod_register_links(dra74x_dra72x_hwmod_ocp_ifs);
+
return ret;
}
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 7/9] ARM: dts: Add support for dra718-evm
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (5 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 6/9] ARM: DRA7: hwmod: Do not register RTC on DRA71 Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 8/9] ARM: omap2plus_defconfig: Enable REGULATOR_GPIO Lokesh Vutla
` (2 subsequent siblings)
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
From: Nishanth Menon <nm@ti.com>
The DRA718-evm is a board based on TI's DRA718 processor targeting
BOM-optimized entry infotainment systems and is a reduced pin and
software compatible derivative of the DRA72 ES2.0 processor.
This platform features:
- 2GB of DDR3L
- Dual 1Gbps Ethernet
- HDMI,
- uSD
- 8GB eMMC
- CAN
- PCIe
- USB3.0
- Video Input Port
- LP873x PMIC
More information can be found here[1].
Adding support for this board while reusing the data available in
dra72-evm-common.dtsi.
[1] http://www.ti.com/product/dra718
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/dra71-evm.dts | 230 ++++++++++++++++++++++++++++++++
arch/arm/boot/dts/dra72-evm-common.dtsi | 6 +-
3 files changed, 236 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/boot/dts/dra71-evm.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index befcd26..b92d501 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -590,7 +590,8 @@ dtb-$(CONFIG_SOC_DRA7XX) += \
am572x-idk.dtb \
dra7-evm.dtb \
dra72-evm.dtb \
- dra72-evm-revc.dtb
+ dra72-evm-revc.dtb \
+ dra71-evm.dtb
dtb-$(CONFIG_ARCH_ORION5X) += \
orion5x-kuroboxpro.dtb \
orion5x-lacie-d2-network.dtb \
diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts
new file mode 100644
index 0000000..2b9a5a8
--- /dev/null
+++ b/arch/arm/boot/dts/dra71-evm.dts
@@ -0,0 +1,230 @@
+/*
+ * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include "dra72-evm-common.dtsi"
+#include <dt-bindings/net/ti-dp83867.h>
+
+/ {
+ compatible = "ti,dra718-evm", "ti,dra718", "ti,dra722", "ti,dra72", "ti,dra7";
+ model = "TI DRA718 EVM";
+
+ memory {
+ device_type = "memory";
+ reg = <0x0 0x80000000 0x0 0x80000000>; /* 2GB */
+ };
+
+ vpo_sd_1v8_3v3: gpio-regulator-TPS74801 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "vddshv8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-boot-on;
+ vin-supply = <&evm_5v0>;
+
+ gpios = <&gpio7 11 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0
+ 3000000 0x1>;
+ };
+
+ poweroff: gpio-poweroff {
+ compatible = "gpio-poweroff";
+ gpios = <&gpio7 30 GPIO_ACTIVE_HIGH>;
+ input;
+ };
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ lp8733: lp8733 at 60 {
+ compatible = "ti,lp8733";
+ reg = <0x60>;
+
+ buck0-in-supply =<&vsys_3v3>;
+ buck1-in-supply =<&vsys_3v3>;
+ ldo0-in-supply =<&evm_5v0>;
+ ldo1-in-supply =<&evm_5v0>;
+
+ lp8733_regulators: regulators {
+ lp8733_buck0_reg: buck0 {
+ /* FB_B0 -> LP8733-BUCK1 - VPO_S1_AVS - VDD_CORE_AVS (core, mpu, gpu) */
+ regulator-name = "lp8733-buck0";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ lp8733_buck1_reg: buck1 {
+ /* FB_B1 -> LP8733-BUCK2 - VPO_S2_AVS - VDD_DSP_AVS (DSP/eve/iva) */
+ regulator-name = "lp8733-buck1";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1250000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ lp8733_ldo0_reg: ldo0 {
+ /* LDO0 -> LP8733-LDO1 - VPO_L1_3V3 - VDDSHV8 (optional) */
+ regulator-name = "lp8733-ldo0";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ lp8733_ldo1_reg: ldo1 {
+ /* LDO1 -> LP8733-LDO2 - VPO_L2_3V3 - VDDA_USB3V3 */
+ regulator-name = "lp8733-ldo1";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+
+ lp8732: lp8732 at 61 {
+ compatible = "ti,lp8732";
+ reg = <0x61>;
+
+ buck0-in-supply =<&vsys_3v3>;
+ buck1-in-supply =<&vsys_3v3>;
+ ldo0-in-supply =<&vsys_3v3>;
+ ldo1-in-supply =<&vsys_3v3>;
+
+ lp8732_regulators: regulators {
+ lp8732_buck0_reg: buck0 {
+ /* FB_B0 -> LP8732-BUCK1 - VPO_S3_1V8 - VDDS_1V8 */
+ regulator-name = "lp8732-buck0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ lp8732_buck1_reg: buck1 {
+ /* FB_B1 -> LP8732-BUCK2 - VPO_S4_DDR - VDD_DDR_1V35 */
+ regulator-name = "lp8732-buck1";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ lp8732_ldo0_reg: ldo0 {
+ /* LDO0 -> LP8732-LDO1 - VPO_L3_1V8 - VDA_1V8_PLL */
+ regulator-name = "lp8732-ldo0";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ lp8732_ldo1_reg: ldo1 {
+ /* LDO1 -> LP8732-LDO2 - VPO_L4_1V8 - VDA_1V8_PHY */
+ regulator-name = "lp8732-ldo1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
+ };
+};
+
+&pcf_gpio_21 {
+ interrupt-parent = <&gpio7>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+};
+
+&pcf_hdmi {
+ p0 {
+ /*
+ * PM_OEn to High: Disable routing I2C3 to PM_I2C
+ * With this PM_SEL(p3) should not matter
+ */
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ output-high;
+ line-name = "pm_oe_n";
+ };
+};
+
+&mmc1 {
+ vmmc_aux-supply = <&vpo_sd_1v8_3v3>;
+};
+
+&mac {
+ mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
+ <&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */
+ <&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */
+ dual_emac;
+};
+
+&cpsw_emac0 {
+ phy_id = <&davinci_mdio>, <2>;
+ phy-mode = "rgmii-id";
+ dual_emac_res_vlan = <1>;
+};
+
+&cpsw_emac1 {
+ phy_id = <&davinci_mdio>, <3>;
+ phy-mode = "rgmii-id";
+ dual_emac_res_vlan = <2>;
+};
+
+&davinci_mdio {
+ dp83867_0: ethernet-phy at 2 {
+ reg = <2>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+ ti,impedance-control = <0x1f>;
+ };
+
+ dp83867_1: ethernet-phy at 3 {
+ reg = <3>;
+ ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
+ ti,tx-internal-delay = <DP83867_RGMIIDCTL_250_PS>;
+ ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_8_B_NIB>;
+ ti,impedance-control = <0x1f>;
+ };
+};
+
+/* No Sata on this device */
+&sata_phy {
+ status = "disabled";
+};
+
+&sata {
+ status = "disabled";
+};
+
+/* No RTC on this device */
+&rtc {
+ status = "disabled";
+};
+
+&usb2_phy1 {
+ phy-supply = <&lp8733_ldo1_reg>;
+};
+
+&usb2_phy2 {
+ phy-supply = <&lp8733_ldo1_reg>;
+};
+
+&dss {
+ /* Supplied by VDA_1V8_PLL */
+ vdda_video-supply = <&lp8732_ldo0_reg>;
+};
+
+&hdmi {
+ /* Supplied by VDA_1V8_PHY */
+ vdda_video-supply = <&lp8732_ldo1_reg>;
+};
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index 9903ac7..e50fbee 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -29,7 +29,8 @@
};
evm_5v0: fixedregulator-evm5v0 {
- /* Output 1 of TPS43351QDAPRQ1 */
+ /* Output 1 of TPS43351QDAPRQ1 on dra72-evm */
+ /* Output 1 of LM5140QRWGTQ1 on dra71-evm */
compatible = "regulator-fixed";
regulator-name = "evm_5v0";
regulator-min-microvolt = <5000000>;
@@ -40,7 +41,8 @@
};
vsys_3v3: fixedregulator-vsys3v3 {
- /* Output 2 of TPS43351QDAPRQ1 */
+ /* Output 2 of TPS43351QDAPRQ1 on dra72-evm */
+ /* Output 2 of LM5140QRWGTQ1 on dra71-evm */
compatible = "regulator-fixed";
regulator-name = "vsys_3v3";
regulator-min-microvolt = <3300000>;
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 8/9] ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (6 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 7/9] ARM: dts: Add support for dra718-evm Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-10-21 10:38 ` [PATCH v2 9/9] ARM: omap2plus_defconfig: Enable LP873X support Lokesh Vutla
2016-11-07 3:49 ` [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
GPIO regulator is used on dra71-evm platform to control MMCSD IO
voltage
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/configs/omap2plus_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index 53e1a88..5695cff 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -270,6 +270,7 @@ CONFIG_MFD_TPS65217=y
CONFIG_MFD_TPS65218=y
CONFIG_MFD_TPS65910=y
CONFIG_TWL6040_CORE=y
+CONFIG_REGULATOR_GPIO=y
CONFIG_REGULATOR_LP872X=y
CONFIG_REGULATOR_PALMAS=y
CONFIG_REGULATOR_PBIAS=y
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 9/9] ARM: omap2plus_defconfig: Enable LP873X support
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (7 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 8/9] ARM: omap2plus_defconfig: Enable REGULATOR_GPIO Lokesh Vutla
@ 2016-10-21 10:38 ` Lokesh Vutla
2016-11-07 3:49 ` [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
9 siblings, 0 replies; 19+ messages in thread
From: Lokesh Vutla @ 2016-10-21 10:38 UTC (permalink / raw)
To: linux-arm-kernel
LP873X family of PMICs are used in dra71x-evm, So enable the same.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
---
arch/arm/configs/omap2plus_defconfig | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/configs/omap2plus_defconfig b/arch/arm/configs/omap2plus_defconfig
index 5695cff..e3fdf4d 100644
--- a/arch/arm/configs/omap2plus_defconfig
+++ b/arch/arm/configs/omap2plus_defconfig
@@ -267,11 +267,13 @@ CONFIG_TWL4030_WATCHDOG=m
CONFIG_MFD_TI_AM335X_TSCADC=m
CONFIG_MFD_PALMAS=y
CONFIG_MFD_TPS65217=y
+CONFIG_MFD_TI_LP873X=y
CONFIG_MFD_TPS65218=y
CONFIG_MFD_TPS65910=y
CONFIG_TWL6040_CORE=y
CONFIG_REGULATOR_GPIO=y
CONFIG_REGULATOR_LP872X=y
+CONFIG_REGULATOR_LP873X=y
CONFIG_REGULATOR_PALMAS=y
CONFIG_REGULATOR_PBIAS=y
CONFIG_REGULATOR_TI_ABB=y
--
2.10.1
^ permalink raw reply related [flat|nested] 19+ messages in thread* [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm
2016-10-21 10:38 [PATCH v2 0/9] ARM: DRA7: Add support for DRA718-evm Lokesh Vutla
` (8 preceding siblings ...)
2016-10-21 10:38 ` [PATCH v2 9/9] ARM: omap2plus_defconfig: Enable LP873X support Lokesh Vutla
@ 2016-11-07 3:49 ` Lokesh Vutla
2016-11-09 23:00 ` Tony Lindgren
9 siblings, 1 reply; 19+ messages in thread
From: Lokesh Vutla @ 2016-11-07 3:49 UTC (permalink / raw)
To: linux-arm-kernel
Hi Tony,
On Friday 21 October 2016 04:08 PM, Lokesh Vutla wrote:
> This series does minor dts cleanup for dra72-evm and adds support for
> DRA718-evm.
Do you have any comments on this series?
Thanks and regards,
Lokesh
>
> Changes since v1:
> - Updated xxx-supply to xxx-in-supply in Documentation.
>
> Lokesh Vutla (7):
> ARM: dts: dra72-evm: Remove pinmux configurations for erratum i869
> ARM: dra72-evm: Fix modelling of regulators
> ARM: dts: dra72: Add separate dtsi for tps65917
> regulator: lp873x: Add support for populating input supply
> ARM: OMAP2+: board-generic: add support for DRA71x family
> ARM: omap2plus_defconfig: Enable REGULATOR_GPIO
> ARM: omap2plus_defconfig: Enable LP873X support
>
> Nishanth Menon (2):
> ARM: DRA7: hwmod: Do not register RTC on DRA71
> ARM: dts: Add support for dra718-evm
>
> .../devicetree/bindings/arm/omap/omap.txt | 6 +
> Documentation/devicetree/bindings/mfd/lp873x.txt | 8 +
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/dra71-evm.dts | 230 ++++++++++++++
> arch/arm/boot/dts/dra72-evm-common.dtsi | 348 +++------------------
> arch/arm/boot/dts/dra72-evm-revc.dts | 21 +-
> arch/arm/boot/dts/dra72-evm-tps65917.dtsi | 134 ++++++++
> arch/arm/boot/dts/dra72-evm.dts | 14 +-
> arch/arm/configs/omap2plus_defconfig | 3 +
> arch/arm/mach-omap2/board-generic.c | 1 +
> arch/arm/mach-omap2/omap_hwmod_7xx_data.c | 10 +-
> drivers/regulator/lp873x-regulator.c | 1 +
> 12 files changed, 453 insertions(+), 326 deletions(-)
> create mode 100644 arch/arm/boot/dts/dra71-evm.dts
> create mode 100644 arch/arm/boot/dts/dra72-evm-tps65917.dtsi
>
^ permalink raw reply [flat|nested] 19+ messages in thread