[PATCH 02/14] ARM: dts: armada-375: Use the node labels

Gregory CLEMENT
2016-11-10T00:09:48Z

Use the node label when possible. As a result it flattens the device tree

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
arch/arm/boot/dts/armada-375-db.dts | 269 ++++++++++++++++++------------------
1 file changed, 136 insertions(+), 133 deletions(-)

diff --git a/arch/arm/boot/dts/armada-375-db.dts b/arch/arm/boot/dts/armada-375-db.dts
index cded5f0a262d..b33a674088ed 100644
--- a/arch/arm/boot/dts/armada-375-db.dts
+++ b/arch/arm/boot/dts/armada-375-db.dts
@@ -69,138 +69,141 @@
MBUS_ID(0x09, 0x09) 0 0xf1100000 0x10000
MBUS_ID(0x09, 0x05) 0 0xf1110000 0x10000>;

- internal-regs {
- spi at 10600 {
- pinctrl-0 = <&spi0_pins>;
- pinctrl-names = "default";
- /*
- * SPI conflicts with NAND, so we disable it
- * here, and select NAND as the enabled device
- * by default.
- */
- status = "disabled";
-
- spi-flash at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "n25q128a13", "jedec,spi-nor";
- reg = <0>; /* Chip select 0 */
- spi-max-frequency = <108000000>;
- };
- };
-
- i2c at 11000 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c0_pins>;
- pinctrl-names = "default";
- };
-
- i2c at 11100 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-0 = <&i2c1_pins>;
- pinctrl-names = "default";
- };
-
- serial at 12000 {
- status = "okay";
- };
-
- pinctrl {
- sdio_st_pins: sdio-st-pins {
- marvell,pins = "mpp44", "mpp45";
- marvell,function = "gpio";
- };
- };
-
- sata at a0000 {
- status = "okay";
- nr-ports = <2>;
- };
-
- nand: nand at d0000 {
- pinctrl-0 = <&nand_pins>;
- pinctrl-names = "default";
- status = "okay";
- num-cs = <1>;
- marvell,nand-keep-config;
- marvell,nand-enable-arbiter;
- nand-on-flash-bbt;
- nand-ecc-strength = <4>;
- nand-ecc-step-size = <512>;
-
- partition at 0 {
- label = "U-Boot";
- reg = <0 0x800000>;
- };
- partition at 800000 {
- label = "Linux";
- reg = <0x800000 0x800000>;
- };
- partition at 1000000 {
- label = "Filesystem";
- reg = <0x1000000 0x3f000000>;
- };
- };
-
- usb at 54000 {
- status = "okay";
- };
-
- usb3 at 58000 {
- status = "okay";
- };
-
- mvsdio at d4000 {
- pinctrl-0 = <&sdio_pins &sdio_st_pins>;
- pinctrl-names = "default";
- status = "okay";
- cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
- wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
- };
-
- mdio {
- phy0: ethernet-phy at 0 {
- reg = <0>;
- };
-
- phy3: ethernet-phy at 3 {
- reg = <3>;
- };
- };
-
- ethernet at f0000 {
- status = "okay";
-
- eth0 at c4000 {
- status = "okay";
- phy = <&phy0>;
- phy-mode = "rgmii-id";
- };
-
- eth1 at c5000 {
- status = "okay";
- phy = <&phy3>;
- phy-mode = "gmii";
- };
- };
- };
-
- pcie-controller {
- status = "okay";
- /*
- * The two PCIe units are accessible through
- * standard PCIe slots on the board.
- */
- pcie at 1,0 {
- /* Port 0, Lane 0 */
- status = "okay";
- };
- pcie at 2,0 {
- /* Port 1, Lane 0 */
- status = "okay";
- };
- };
};
};
+&pciec {
+ status = "okay";
+};
+
+/*
+ * The two PCIe units are accessible through
+ * standard PCIe slots on the board.
+ */
+&pcie0 {
+ /* Port 0, Lane 0 */
+ status = "okay";
+};
+
+&pcie1 {
+ /* Port 1, Lane 0 */
+ status = "okay";
+};
+
+
+&spi0 {
+ pinctrl-0 = <&spi0_pins>;
+ pinctrl-names = "default";
+
+ /*
+ * SPI conflicts with NAND, so we disable it here, and
+ * select NAND as the enabled device by default.
+ */
+
+ status = "disabled";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "n25q128a13", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <108000000>;
+ };
+};
+
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+};
+
+&i2c1 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c1_pins>;
+ pinctrl-names = "default";
+};
+
+&uart0 {
+ status = "okay";
+};
+
+&pinctrl {
+ sdio_st_pins: sdio-st-pins {
+ marvell,pins = "mpp44", "mpp45";
+ marvell,function = "gpio";
+ };
+};
+
+&sata {
+ status = "okay";
+ nr-ports = <2>;
+};
+
+&nand {
+ pinctrl-0 = <&nand_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+
+ partition at 0 {
+ label = "U-Boot";
+ reg = <0 0x800000>;
+ };
+ partition at 800000 {
+ label = "Linux";
+ reg = <0x800000 0x800000>;
+ };
+ partition at 1000000 {
+ label = "Filesystem";
+ reg = <0x1000000 0x3f000000>;
+ };
+};
+
+&usb1 {
+ status = "okay";
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&sdio {
+ pinctrl-0 = <&sdio_pins &sdio_st_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ cd-gpios = <&gpio1 12 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&gpio1 13 GPIO_ACTIVE_HIGH>;
+};
+
+&mdio {
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+
+ phy3: ethernet-phy at 3 {
+ reg = <3>;
+ };
+};
+
+&ethernet {
+ status = "okay";
+};
+
+
+&eth0 {
+ status = "okay";
+ phy = <&phy0>;
+ phy-mode = "rgmii-id";
+};
+
+&eth1 {
+ status = "okay";
+ phy = <&phy3>;
+ phy-mode = "gmii";
+};
--
2.10.1