From mboxrd@z Thu Jan 1 00:00:00 1970 From: wens@csie.org (Chen-Yu Tsai) Date: Wed, 16 Nov 2016 23:42:32 +0800 Subject: [PATCH v4 2/2] ARM: dts: sun6i: hummingbird-a31: Enable display output through VGA bridge In-Reply-To: <20161116154232.872-1-wens@csie.org> References: <20161116154232.872-1-wens@csie.org> Message-ID: <20161116154232.872-3-wens@csie.org> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org The Hummingbird A31 board has a VGA DAC which converts RGB output from the LCD interface to VGA analog signals. Add nodes for the VGA DAC, its power supply, and enable this part of the display pipeline. Signed-off-by: Chen-Yu Tsai --- arch/arm/boot/dts/sun6i-a31-hummingbird.dts | 67 +++++++++++++++++++++++++++++ 1 file changed, 67 insertions(+) diff --git a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts index 62287bd2aeb5..b168d6df2b30 100644 --- a/arch/arm/boot/dts/sun6i-a31-hummingbird.dts +++ b/arch/arm/boot/dts/sun6i-a31-hummingbird.dts @@ -63,6 +63,60 @@ stdout-path = "serial0:115200n8"; }; + vga-connector { + compatible = "vga-connector"; + + port { + vga_con_in: endpoint { + remote-endpoint = <&vga_dac_out>; + }; + }; + }; + + vga-dac { + compatible = "dumb-vga-dac"; + vdd-supply = <®_vga_3v3>; + #address-cells = <1>; + #size-cells = <0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port at 0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + vga_dac_in: endpoint at 0 { + reg = <0>; + remote-endpoint = <&tcon0_out_vga>; + }; + }; + + port at 1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + + vga_dac_out: endpoint at 0 { + reg = <0>; + remote-endpoint = <&vga_con_in>; + }; + }; + }; + }; + + reg_vga_3v3: vga_3v3_regulator { + compatible = "regulator-fixed"; + regulator-name = "vga-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + enable-active-high; + gpio = <&pio 7 25 GPIO_ACTIVE_HIGH>; /* PH25 */ + }; + wifi_pwrseq: wifi_pwrseq { compatible = "mmc-pwrseq-simple"; reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 */ @@ -253,6 +307,19 @@ status = "okay"; }; +&tcon0 { + pinctrl-names = "default"; + pinctrl-0 = <&lcd0_rgb888_pins>; + status = "okay"; +}; + +&tcon0_out { + tcon0_out_vga: endpoint at 0 { + reg = <0>; + remote-endpoint = <&vga_dac_in>; + }; +}; + &uart0 { pinctrl-names = "default"; pinctrl-0 = <&uart0_pins_a>; -- 2.10.2