[PATCH v3 net-next 0/3] Add support for the ethernet switch on the ESPRESSObin

[PATCH v3 net-next 0/3] Add support for the ethernet switch on the ESPRESSObin

[Romain Perier]

This set of patches adds support for the Marvell ethernet switch 88E6341.
It also add the devicetree definition of this switch to the DT board.

Romain Perier (3):
  net: dsa: mv88e6xxx: Don't forbid MDIO I/Os for PHY addr >=
    num_of_ports
  net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341/88E6141
  arm64: dts: marvell: Add ethernet switch definition for the
    ESPRESSObin

 .../boot/dts/marvell/armada-3720-espressobin.dts   | 66 ++++++++++++++++++++++
 drivers/net/dsa/mv88e6xxx/chip.c                   | 48 ++++++++++++++--
 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h              |  4 +-
 3 files changed, 111 insertions(+), 7 deletions(-)

-- 
2.9.3

[PATCH v3 net-next 1/3] net: dsa: mv88e6xxx: Don't forbid MDIO I/Os for PHY addr >= num_of_ports

[Romain Perier]

Some Marvell ethernet switches have internal ethernet transceivers with
hardcoded phy addresses. These addresses can be grearer than the number
of ports or its value might be different than the associated port number.
This is for example the case for MV88E6341 that has 6 ports and internal
Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.

This commits fixes the issue by removing the condition in MDIO callbacks.

Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---

Changes in v2:
 - Added tag "Reviewed-by" by Andrew
 - Fixed typo in the commit log

 drivers/net/dsa/mv88e6xxx/chip.c | 6 ------
 1 file changed, 6 deletions(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index b5f0e1e..76d944e 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -2881,9 +2881,6 @@ static int mv88e6xxx_mdio_read(struct mii_bus *bus, int phy, int reg)
 	u16 val;
 	int err;
 
-	if (phy >= mv88e6xxx_num_ports(chip))
-		return 0xffff;
-
 	mutex_lock(&chip->reg_lock);
 	err = mv88e6xxx_phy_read(chip, phy, reg, &val);
 	mutex_unlock(&chip->reg_lock);
@@ -2896,9 +2893,6 @@ static int mv88e6xxx_mdio_write(struct mii_bus *bus, int phy, int reg, u16 val)
 	struct mv88e6xxx_chip *chip = bus->priv;
 	int err;
 
-	if (phy >= mv88e6xxx_num_ports(chip))
-		return 0xffff;
-
 	mutex_lock(&chip->reg_lock);
 	err = mv88e6xxx_phy_write(chip, phy, reg, val);
 	mutex_unlock(&chip->reg_lock);
-- 
2.9.3

[PATCH v3 net-next 1/3] net: dsa: mv88e6xxx: Don't forbid MDIO I/Os for PHY addr >= num_of_ports

[Gregory CLEMENT]

Hi Romain,


it seems there is a remaining typo :)

 On mer., d?c. 21 2016, Romain Perier <romain.perier@free-electrons.com> wrote:

> Some Marvell ethernet switches have internal ethernet transceivers with
> hardcoded phy addresses. These addresses can be grearer than the number
                                                  greater
> of ports or its value might be different than the associated port number.
> This is for example the case for MV88E6341 that has 6 ports and internal
> Port 1 to Port4 PHYs mapped at SMI addresses from 0x11 to 0x14.
>
> This commits fixes the issue by removing the condition in MDIO callbacks.
>
> Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
> Reviewed-by: Andrew Lunn <andrew@lunn.ch>
> ---
>
> Changes in v2:
>  - Added tag "Reviewed-by" by Andrew
>  - Fixed typo in the commit log
>
>  drivers/net/dsa/mv88e6xxx/chip.c | 6 ------
>  1 file changed, 6 deletions(-)
>
> diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
> index b5f0e1e..76d944e 100644
> --- a/drivers/net/dsa/mv88e6xxx/chip.c
> +++ b/drivers/net/dsa/mv88e6xxx/chip.c
> @@ -2881,9 +2881,6 @@ static int mv88e6xxx_mdio_read(struct mii_bus *bus, int phy, int reg)
>  	u16 val;
>  	int err;
>  
> -	if (phy >= mv88e6xxx_num_ports(chip))
> -		return 0xffff;
> -
>  	mutex_lock(&chip->reg_lock);
>  	err = mv88e6xxx_phy_read(chip, phy, reg, &val);
>  	mutex_unlock(&chip->reg_lock);
> @@ -2896,9 +2893,6 @@ static int mv88e6xxx_mdio_write(struct mii_bus *bus, int phy, int reg, u16 val)
>  	struct mv88e6xxx_chip *chip = bus->priv;
>  	int err;
>  
> -	if (phy >= mv88e6xxx_num_ports(chip))
> -		return 0xffff;
> -
>  	mutex_lock(&chip->reg_lock);
>  	err = mv88e6xxx_phy_write(chip, phy, reg, val);
>  	mutex_unlock(&chip->reg_lock);
> -- 
> 2.9.3
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

[PATCH v3 net-next 2/3] net: dsa: mv88e6xxx: Add support for ethernet switch 88E6341/88E6141

[Romain Perier]

The Marvell 88E6341 device is single-chip, 6-port ethernet switch with
four integrated 10/100/1000Mbps ethernet transceivers and one high speed
SerDes interfaces. It is compatible with switches of family 88E6352.

This commit adds basic support for this switch by describing its
capabilities to the driver.

Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---

Changes in v3:
 - Added tag "Reviewed-by" by Andrew
 
Changes in v2:
 - Add a dedicated data structure for the operations of the 88E6341
 - Re-ordered PORT_SWITCH_ID_PROD_NUM_6341 in alphabetic order with other
   macros

 drivers/net/dsa/mv88e6xxx/chip.c      | 42 +++++++++++++++++++++++++++++++++++
 drivers/net/dsa/mv88e6xxx/mv88e6xxx.h |  4 +++-
 2 files changed, 45 insertions(+), 1 deletion(-)

diff --git a/drivers/net/dsa/mv88e6xxx/chip.c b/drivers/net/dsa/mv88e6xxx/chip.c
index 76d944e..5e97dc4 100644
--- a/drivers/net/dsa/mv88e6xxx/chip.c
+++ b/drivers/net/dsa/mv88e6xxx/chip.c
@@ -3625,6 +3625,34 @@ static const struct mv88e6xxx_ops mv88e6321_ops = {
 	.reset = mv88e6352_g1_reset,
 };
 
+static const struct mv88e6xxx_ops mv88e6341_ops = {
+	/* MV88E6XXX_FAMILY_6352 */
+	.get_eeprom = mv88e6xxx_g2_get_eeprom16,
+	.set_eeprom = mv88e6xxx_g2_set_eeprom16,
+	.set_switch_mac = mv88e6xxx_g2_set_switch_mac,
+	.phy_read = mv88e6xxx_g2_smi_phy_read,
+	.phy_write = mv88e6xxx_g2_smi_phy_write,
+	.port_set_link = mv88e6xxx_port_set_link,
+	.port_set_duplex = mv88e6xxx_port_set_duplex,
+	.port_set_rgmii_delay = mv88e6352_port_set_rgmii_delay,
+	.port_set_speed = mv88e6352_port_set_speed,
+	.port_tag_remap = mv88e6095_port_tag_remap,
+	.port_set_frame_mode = mv88e6351_port_set_frame_mode,
+	.port_set_egress_unknowns = mv88e6351_port_set_egress_unknowns,
+	.port_set_ether_type = mv88e6351_port_set_ether_type,
+	.port_jumbo_config = mv88e6165_port_jumbo_config,
+	.port_egress_rate_limiting = mv88e6097_port_egress_rate_limiting,
+	.port_pause_config = mv88e6097_port_pause_config,
+	.stats_snapshot = mv88e6320_g1_stats_snapshot,
+	.stats_get_sset_count = mv88e6095_stats_get_sset_count,
+	.stats_get_strings = mv88e6095_stats_get_strings,
+	.stats_get_stats = mv88e6095_stats_get_stats,
+	.g1_set_cpu_port = mv88e6095_g1_set_cpu_port,
+	.g1_set_egress_port = mv88e6095_g1_set_egress_port,
+	.mgmt_rsvd2cpu = mv88e6095_g2_mgmt_rsvd2cpu,
+	.reset = mv88e6352_g1_reset,
+};
+
 static const struct mv88e6xxx_ops mv88e6350_ops = {
 	/* MV88E6XXX_FAMILY_6351 */
 	.set_switch_mac = mv88e6xxx_g2_set_switch_mac,
@@ -4086,6 +4114,20 @@ static const struct mv88e6xxx_info mv88e6xxx_table[] = {
 		.ops = &mv88e6321_ops,
 	},
 
+	[MV88E6341] = {
+		.prod_num = PORT_SWITCH_ID_PROD_NUM_6341,
+		.family = MV88E6XXX_FAMILY_6352,
+		.name = "Marvell 88E6341",
+		.num_databases = 4096,
+		.num_ports = 6,
+		.port_base_addr = 0x10,
+		.global1_addr = 0x1b,
+		.age_time_coeff = 15000,
+		.tag_protocol = DSA_TAG_PROTO_EDSA,
+		.flags = MV88E6XXX_FLAGS_FAMILY_6352,
+		.ops = &mv88e6341_ops,
+	},
+
 	[MV88E6350] = {
 		.prod_num = PORT_SWITCH_ID_PROD_NUM_6350,
 		.family = MV88E6XXX_FAMILY_6351,
diff --git a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
index af54bae..cb55fdb 100644
--- a/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
+++ b/drivers/net/dsa/mv88e6xxx/mv88e6xxx.h
@@ -100,6 +100,7 @@
 #define PORT_SWITCH_ID_PROD_NUM_6240	0x240
 #define PORT_SWITCH_ID_PROD_NUM_6290	0x290
 #define PORT_SWITCH_ID_PROD_NUM_6321	0x310
+#define PORT_SWITCH_ID_PROD_NUM_6341	0x340
 #define PORT_SWITCH_ID_PROD_NUM_6352	0x352
 #define PORT_SWITCH_ID_PROD_NUM_6350	0x371
 #define PORT_SWITCH_ID_PROD_NUM_6351	0x375
@@ -432,6 +433,7 @@ enum mv88e6xxx_model {
 	MV88E6290,
 	MV88E6320,
 	MV88E6321,
+	MV88E6341,
 	MV88E6350,
 	MV88E6351,
 	MV88E6352,
@@ -448,7 +450,7 @@ enum mv88e6xxx_family {
 	MV88E6XXX_FAMILY_6185,	/* 6108 6121 6122 6131 6152 6155 6182 6185 */
 	MV88E6XXX_FAMILY_6320,	/* 6320 6321 */
 	MV88E6XXX_FAMILY_6351,	/* 6171 6175 6350 6351 */
-	MV88E6XXX_FAMILY_6352,	/* 6172 6176 6240 6352 */
+	MV88E6XXX_FAMILY_6352,	/* 6172 6176 6240 6341 6352 */
 	MV88E6XXX_FAMILY_6390,  /* 6190 6190X 6191 6290 6390 6390X */
 };
 
-- 
2.9.3

[PATCH v3 net-next 3/3] arm64: dts: marvell: Add ethernet switch definition for the ESPRESSObin

[Romain Perier]

This defines and enables the Marvell ethernet switch MVE886341 on the
Marvell ESPRESSObin board.

Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
---

Changes in v3:
 - Changed the node switch0 to be at 1
 - Removed reg=<1> from the mdio node, finally that's not required

Changes in v2:
 - EXPRESSObin -> ESPRESSObin
 - phy nodes definition must contain the internal bus address after the @

 .../boot/dts/marvell/armada-3720-espressobin.dts   | 66 ++++++++++++++++++++++
 1 file changed, 66 insertions(+)

diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
index 83178d9..12d9f65 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
@@ -80,3 +80,69 @@
 &usb3 {
 	status = "okay";
 };
+
+&mdio {
+	switch0: switch0 at 1 {
+		compatible = "marvell,mv88e6085";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+
+		dsa,member = <0 0>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port at 0 {
+				reg = <0>;
+				label = "cpu";
+				ethernet = <&eth0>;
+			};
+
+			port at 1 {
+				reg = <1>;
+				label = "wan";
+				phy-handle = <&switch0phy0>;
+			};
+
+			port at 2 {
+				reg = <2>;
+				label = "lan0";
+				phy-handle = <&switch0phy1>;
+			};
+
+			port at 3 {
+				reg = <3>;
+				label = "lan1";
+				phy-handle = <&switch0phy2>;
+			};
+
+		};
+
+		mdio {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			switch0phy0: switch0phy0 at 11 {
+				reg = <0x11>;
+			};
+			switch0phy1: switch0phy1 at 12 {
+				reg = <0x12>;
+			};
+			switch0phy2: switch0phy2 at 13 {
+				reg = <0x13>;
+			};
+		};
+	};
+};
+
+&eth0 {
+	phy-mode = "rgmii-id";
+	status = "okay";
+
+	fixed-link {
+		speed = <1000>;
+		full-duplex;
+	};
+};
-- 
2.9.3

[PATCH v3 net-next 3/3] arm64: dts: marvell: Add ethernet switch definition for the ESPRESSObin

[Gregory CLEMENT]

Hi Romain,
 
 On mer., d?c. 21 2016, Romain Perier <romain.perier@free-electrons.com> wrote:

> This defines and enables the Marvell ethernet switch MVE886341 on the
> Marvell ESPRESSObin board.

This patch looks OK now.

Applied on mvebu/dt64-4.11

So you can remove it from you next version because I don't want this
patch will be applied through the netdev branch. Indeed I expect more
changes in this file for v4.11 and it will be easier to have the change
in a single branch to avoid the merge conflict.

Thanks,

Gregory


>
> Signed-off-by: Romain Perier <romain.perier@free-electrons.com>
> ---
>
> Changes in v3:
>  - Changed the node switch0 to be at 1
>  - Removed reg=<1> from the mdio node, finally that's not required
>
> Changes in v2:
>  - EXPRESSObin -> ESPRESSObin
>  - phy nodes definition must contain the internal bus address after the @
>
>  .../boot/dts/marvell/armada-3720-espressobin.dts   | 66 ++++++++++++++++++++++
>  1 file changed, 66 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
> index 83178d9..12d9f65 100644
> --- a/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-espressobin.dts
> @@ -80,3 +80,69 @@
>  &usb3 {
>  	status = "okay";
>  };
> +
> +&mdio {
> +	switch0: switch0 at 1 {
> +		compatible = "marvell,mv88e6085";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +		reg = <1>;
> +
> +		dsa,member = <0 0>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port at 0 {
> +				reg = <0>;
> +				label = "cpu";
> +				ethernet = <&eth0>;
> +			};
> +
> +			port at 1 {
> +				reg = <1>;
> +				label = "wan";
> +				phy-handle = <&switch0phy0>;
> +			};
> +
> +			port at 2 {
> +				reg = <2>;
> +				label = "lan0";
> +				phy-handle = <&switch0phy1>;
> +			};
> +
> +			port at 3 {
> +				reg = <3>;
> +				label = "lan1";
> +				phy-handle = <&switch0phy2>;
> +			};
> +
> +		};
> +
> +		mdio {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			switch0phy0: switch0phy0 at 11 {
> +				reg = <0x11>;
> +			};
> +			switch0phy1: switch0phy1 at 12 {
> +				reg = <0x12>;
> +			};
> +			switch0phy2: switch0phy2 at 13 {
> +				reg = <0x13>;
> +			};
> +		};
> +	};
> +};
> +
> +&eth0 {
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +
> +	fixed-link {
> +		speed = <1000>;
> +		full-duplex;
> +	};
> +};
> -- 
> 2.9.3
>

-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

[PATCH v3 net-next 0/3] Add support for the ethernet switch on the ESPRESSObin

[David Miller]

net-next is not open, please do not submit net-next changes during this
time.