* [PATCHv2 1/5] clk: mvebu: support for 98DX3236 SoC
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
@ 2017-01-05 3:36 ` Chris Packham
2017-01-05 13:53 ` Mark Rutland
2017-01-05 3:36 ` [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
` (6 subsequent siblings)
7 siblings, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-05 3:36 UTC (permalink / raw)
To: linux-arm-kernel
The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
The clock gating options are a subset of those on the Armada XP.
The core clock divider is different to the Armada XP also.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Update devicetree binding documentation for new compatible string
.../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
drivers/clk/mvebu/Makefile | 2 +-
drivers/clk/mvebu/armada-xp.c | 42 +++++
drivers/clk/mvebu/clk-cpu.c | 33 +++-
drivers/clk/mvebu/mv98dx3236-corediv.c | 207 +++++++++++++++++++++
5 files changed, 281 insertions(+), 4 deletions(-)
create mode 100644 drivers/clk/mvebu/mv98dx3236-corediv.c
diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
index 99c214660bdc..7f28506eaee7 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
@@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
Required properties:
- compatible : shall be one of the following:
"marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
+ "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
- reg : Address and length of the clock complex register set, followed
by address and length of the PMU DFS registers
- #clock-cells : should be set to 1.
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
index d9ae97fb43c4..6a3681e3d6db 100644
--- a/drivers/clk/mvebu/Makefile
+++ b/drivers/clk/mvebu/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_ARMADA_39X_CLK) += armada-39x.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-xtal.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-tbg.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-periph.o
-obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o
+obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o mv98dx3236-corediv.o
obj-$(CONFIG_ARMADA_AP806_SYSCON) += ap806-system-controller.o
obj-$(CONFIG_ARMADA_CP110_SYSCON) += cp110-system-controller.o
obj-$(CONFIG_DOVE_CLK) += dove.o dove-divider.o
diff --git a/drivers/clk/mvebu/armada-xp.c b/drivers/clk/mvebu/armada-xp.c
index b3094315a3c0..0413bf8284e0 100644
--- a/drivers/clk/mvebu/armada-xp.c
+++ b/drivers/clk/mvebu/armada-xp.c
@@ -52,6 +52,12 @@ static u32 __init axp_get_tclk_freq(void __iomem *sar)
return 250000000;
}
+/* MV98DX3236 TCLK frequency is fixed to 200MHz */
+static u32 __init mv98dx3236_get_tclk_freq(void __iomem *sar)
+{
+ return 200000000;
+}
+
static const u32 axp_cpu_freqs[] __initconst = {
1000000000,
1066000000,
@@ -89,6 +95,12 @@ static u32 __init axp_get_cpu_freq(void __iomem *sar)
return cpu_freq;
}
+/* MV98DX3236 CLK frequency is fixed to 800MHz */
+static u32 __init mv98dx3236_get_cpu_freq(void __iomem *sar)
+{
+ return 800000000;
+}
+
static const int axp_nbclk_ratios[32][2] __initconst = {
{0, 1}, {1, 2}, {2, 2}, {2, 2},
{1, 2}, {1, 2}, {1, 1}, {2, 3},
@@ -158,6 +170,14 @@ static const struct coreclk_soc_desc axp_coreclks = {
.num_ratios = ARRAY_SIZE(axp_coreclk_ratios),
};
+static const struct coreclk_soc_desc mv98dx3236_coreclks = {
+ .get_tclk_freq = mv98dx3236_get_tclk_freq,
+ .get_cpu_freq = mv98dx3236_get_cpu_freq,
+ .get_clk_ratio = NULL,
+ .ratios = NULL,
+ .num_ratios = 0,
+};
+
/*
* Clock Gating Control
*/
@@ -195,6 +215,15 @@ static const struct clk_gating_soc_desc axp_gating_desc[] __initconst = {
{ }
};
+static const struct clk_gating_soc_desc mv98dx3236_gating_desc[] __initconst = {
+ { "ge1", NULL, 3, 0 },
+ { "ge0", NULL, 4, 0 },
+ { "pex00", NULL, 5, 0 },
+ { "sdio", NULL, 17, 0 },
+ { "xor0", NULL, 22, 0 },
+ { }
+};
+
static void __init axp_clk_init(struct device_node *np)
{
struct device_node *cgnp =
@@ -206,3 +235,16 @@ static void __init axp_clk_init(struct device_node *np)
mvebu_clk_gating_setup(cgnp, axp_gating_desc);
}
CLK_OF_DECLARE(axp_clk, "marvell,armada-xp-core-clock", axp_clk_init);
+
+static void __init mv98dx3236_clk_init(struct device_node *np)
+{
+ struct device_node *cgnp =
+ of_find_compatible_node(NULL, NULL, "marvell,armada-xp-gating-clock");
+
+ mvebu_coreclk_setup(np, &mv98dx3236_coreclks);
+
+ if (cgnp)
+ mvebu_clk_gating_setup(cgnp, mv98dx3236_gating_desc);
+}
+CLK_OF_DECLARE(mv98dx3236_clk, "marvell,mv98dx3236-core-clock",
+ mv98dx3236_clk_init);
diff --git a/drivers/clk/mvebu/clk-cpu.c b/drivers/clk/mvebu/clk-cpu.c
index 5837eb8a212f..29f295e7a36b 100644
--- a/drivers/clk/mvebu/clk-cpu.c
+++ b/drivers/clk/mvebu/clk-cpu.c
@@ -165,7 +165,9 @@ static const struct clk_ops cpu_ops = {
.set_rate = clk_cpu_set_rate,
};
-static void __init of_cpu_clk_setup(struct device_node *node)
+/* Add parameter to allow this to support different clock operations. */
+static void __init _of_cpu_clk_setup(struct device_node *node,
+ const struct clk_ops *cpu_clk_ops)
{
struct cpu_clk *cpuclk;
void __iomem *clock_complex_base = of_iomap(node, 0);
@@ -218,7 +220,7 @@ static void __init of_cpu_clk_setup(struct device_node *node)
cpuclk[cpu].hw.init = &init;
init.name = cpuclk[cpu].clk_name;
- init.ops = &cpu_ops;
+ init.ops = cpu_clk_ops;
init.flags = 0;
init.parent_names = &cpuclk[cpu].parent_name;
init.num_parents = 1;
@@ -243,5 +245,30 @@ static void __init of_cpu_clk_setup(struct device_node *node)
iounmap(clock_complex_base);
}
+/* Use this function to call the generic setup with the correct
+ * clock operation
+ */
+static void __init of_cpu_clk_setup(struct device_node *node)
+{
+ _of_cpu_clk_setup(node, &cpu_ops);
+}
+
CLK_OF_DECLARE(armada_xp_cpu_clock, "marvell,armada-xp-cpu-clock",
- of_cpu_clk_setup);
+ of_cpu_clk_setup);
+
+/* Define the clock and operations for the mv98dx3236 - it cannot perform
+ * any operations.
+ */
+static const struct clk_ops mv98dx3236_cpu_ops = {
+ .recalc_rate = NULL,
+ .round_rate = NULL,
+ .set_rate = NULL,
+};
+
+static void __init of_mv98dx3236_cpu_clk_setup(struct device_node *node)
+{
+ _of_cpu_clk_setup(node, &mv98dx3236_cpu_ops);
+}
+
+CLK_OF_DECLARE(mv98dx3236_cpu_clock, "marvell,mv98dx3236-cpu-clock",
+ of_mv98dx3236_cpu_clk_setup);
diff --git a/drivers/clk/mvebu/mv98dx3236-corediv.c b/drivers/clk/mvebu/mv98dx3236-corediv.c
new file mode 100644
index 000000000000..3060764a8e5d
--- /dev/null
+++ b/drivers/clk/mvebu/mv98dx3236-corediv.c
@@ -0,0 +1,207 @@
+/*
+ * MV98DX3236 Core divider clock
+ *
+ * Copyright (C) 2015 Allied Telesis Labs
+ *
+ * Based on armada-xp-corediv.c
+ * Copyright (C) 2015 Marvell
+ *
+ * John Thompson <john.thompson@alliedtelesis.co.nz>
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+#include <linux/kernel.h>
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/delay.h>
+#include "common.h"
+
+#define CORE_CLK_DIV_RATIO_MASK 0xff
+
+#define CLK_DIV_RATIO_NAND_MASK 0x0f
+#define CLK_DIV_RATIO_NAND_OFFSET 6
+#define CLK_DIV_RATIO_NAND_FORCE_RELOAD_BIT 26
+
+#define RATIO_RELOAD_BIT BIT(10)
+#define RATIO_REG_OFFSET 0x08
+
+/*
+ * This structure represents one core divider clock for the clock
+ * framework, and is dynamically allocated for each core divider clock
+ * existing in the current SoC.
+ */
+struct clk_corediv {
+ struct clk_hw hw;
+ void __iomem *reg;
+ spinlock_t lock;
+};
+
+static struct clk_onecell_data clk_data;
+
+
+#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
+
+static int mv98dx3236_corediv_is_enabled(struct clk_hw *hwclk)
+{
+ /* Core divider is always active */
+ return 1;
+}
+
+static int mv98dx3236_corediv_enable(struct clk_hw *hwclk)
+{
+ /* always succeeds */
+ return 0;
+}
+
+static void mv98dx3236_corediv_disable(struct clk_hw *hwclk)
+{
+ /* can't be disabled so is left alone */
+}
+
+static unsigned long mv98dx3236_corediv_recalc_rate(struct clk_hw *hwclk,
+ unsigned long parent_rate)
+{
+ struct clk_corediv *corediv = to_corediv_clk(hwclk);
+ u32 reg, div;
+
+ reg = readl(corediv->reg + RATIO_REG_OFFSET);
+ div = (reg >> CLK_DIV_RATIO_NAND_OFFSET) & CLK_DIV_RATIO_NAND_MASK;
+ return parent_rate / div;
+}
+
+static long mv98dx3236_corediv_round_rate(struct clk_hw *hwclk,
+ unsigned long rate, unsigned long *parent_rate)
+{
+ /* Valid ratio are 1:4, 1:5, 1:6 and 1:8 */
+ u32 div;
+
+ div = *parent_rate / rate;
+ if (div < 4)
+ div = 4;
+ else if (div > 6)
+ div = 8;
+
+ return *parent_rate / div;
+}
+
+static int mv98dx3236_corediv_set_rate(struct clk_hw *hwclk, unsigned long rate,
+ unsigned long parent_rate)
+{
+ struct clk_corediv *corediv = to_corediv_clk(hwclk);
+ unsigned long flags = 0;
+ u32 reg, div;
+
+ div = parent_rate / rate;
+
+ spin_lock_irqsave(&corediv->lock, flags);
+
+ /* Write new divider to the divider ratio register */
+ reg = readl(corediv->reg + RATIO_REG_OFFSET);
+ reg &= ~(CLK_DIV_RATIO_NAND_MASK << CLK_DIV_RATIO_NAND_OFFSET);
+ reg |= (div & CLK_DIV_RATIO_NAND_MASK) << CLK_DIV_RATIO_NAND_OFFSET;
+ writel(reg, corediv->reg + RATIO_REG_OFFSET);
+
+ /* Set reload-force for this clock */
+ reg = readl(corediv->reg) | BIT(CLK_DIV_RATIO_NAND_FORCE_RELOAD_BIT);
+ writel(reg, corediv->reg);
+
+ /* Now trigger the clock update */
+ reg = readl(corediv->reg + RATIO_REG_OFFSET) | RATIO_RELOAD_BIT;
+ writel(reg, corediv->reg + RATIO_REG_OFFSET);
+
+ /*
+ * Wait for clocks to settle down, and then clear all the
+ * ratios request and the reload request.
+ */
+ udelay(1000);
+ reg &= ~(CORE_CLK_DIV_RATIO_MASK | RATIO_RELOAD_BIT);
+ writel(reg, corediv->reg + RATIO_REG_OFFSET);
+ udelay(1000);
+
+ spin_unlock_irqrestore(&corediv->lock, flags);
+
+ return 0;
+}
+
+static const struct clk_ops ops = {
+ .enable = mv98dx3236_corediv_enable,
+ .disable = mv98dx3236_corediv_disable,
+ .is_enabled = mv98dx3236_corediv_is_enabled,
+ .recalc_rate = mv98dx3236_corediv_recalc_rate,
+ .round_rate = mv98dx3236_corediv_round_rate,
+ .set_rate = mv98dx3236_corediv_set_rate,
+};
+
+static void __init mv98dx3236_corediv_clk_init(struct device_node *node)
+{
+ struct clk_init_data init;
+ struct clk_corediv *corediv;
+ struct clk **clks;
+ void __iomem *base;
+ const __be32 *off;
+ const char *parent_name;
+ const char *clk_name;
+ int len;
+ struct device_node *dfx_node;
+
+ dfx_node = of_parse_phandle(node, "base", 0);
+ if (WARN_ON(!dfx_node))
+ return;
+
+ off = of_get_property(node, "reg", &len);
+ if (WARN_ON(!off))
+ return;
+
+ base = of_iomap(dfx_node, 0);
+ if (WARN_ON(!base))
+ return;
+
+ of_node_put(dfx_node);
+
+ parent_name = of_clk_get_parent_name(node, 0);
+
+ clk_data.clk_num = 1;
+
+ /* clks holds the clock array */
+ clks = kcalloc(clk_data.clk_num, sizeof(struct clk *),
+ GFP_KERNEL);
+ if (WARN_ON(!clks))
+ goto err_unmap;
+ /* corediv holds the clock specific array */
+ corediv = kcalloc(clk_data.clk_num, sizeof(struct clk_corediv),
+ GFP_KERNEL);
+ if (WARN_ON(!corediv))
+ goto err_free_clks;
+
+ spin_lock_init(&corediv->lock);
+
+ of_property_read_string_index(node, "clock-output-names",
+ 0, &clk_name);
+
+ init.num_parents = 1;
+ init.parent_names = &parent_name;
+ init.name = clk_name;
+ init.ops = &ops;
+ init.flags = 0;
+
+ corediv[0].reg = (void *)((int)base + be32_to_cpu(*off));
+ corediv[0].hw.init = &init;
+
+ clks[0] = clk_register(NULL, &corediv[0].hw);
+ WARN_ON(IS_ERR(clks[0]));
+
+ clk_data.clks = clks;
+ of_clk_add_provider(node, of_clk_src_onecell_get, &clk_data);
+ return;
+
+err_free_clks:
+ kfree(clks);
+err_unmap:
+ iounmap(base);
+}
+
+CLK_OF_DECLARE(mv98dx3236_corediv_clk, "marvell,mv98dx3236-corediv-clock",
+ mv98dx3236_corediv_clk_init);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv2 1/5] clk: mvebu: support for 98DX3236 SoC
2017-01-05 3:36 ` [PATCHv2 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
@ 2017-01-05 13:53 ` Mark Rutland
2017-01-05 23:05 ` Chris Packham
0 siblings, 1 reply; 43+ messages in thread
From: Mark Rutland @ 2017-01-05 13:53 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 05, 2017 at 04:36:37PM +1300, Chris Packham wrote:
> The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
> the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
>
> The clock gating options are a subset of those on the Armada XP.
>
> The core clock divider is different to the Armada XP also.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - Update devicetree binding documentation for new compatible string
>
> .../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
> drivers/clk/mvebu/Makefile | 2 +-
> drivers/clk/mvebu/armada-xp.c | 42 +++++
> drivers/clk/mvebu/clk-cpu.c | 33 +++-
> drivers/clk/mvebu/mv98dx3236-corediv.c | 207 +++++++++++++++++++++
> 5 files changed, 281 insertions(+), 4 deletions(-)
> create mode 100644 drivers/clk/mvebu/mv98dx3236-corediv.c
It looks like you also need to update
Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt for the
addition of "marvell,mv98dx3236-corediv-clock".
>
> diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
> index 99c214660bdc..7f28506eaee7 100644
> --- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
> +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
> @@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
> Required properties:
> - compatible : shall be one of the following:
> "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
> + "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
> - reg : Address and length of the clock complex register set, followed
> by address and length of the PMU DFS registers
> - #clock-cells : should be set to 1.
[...]
> +static void __init mv98dx3236_corediv_clk_init(struct device_node *node)
> +{
> + struct clk_init_data init;
> + struct clk_corediv *corediv;
> + struct clk **clks;
> + void __iomem *base;
> + const __be32 *off;
> + const char *parent_name;
> + const char *clk_name;
> + int len;
> + struct device_node *dfx_node;
> +
> + dfx_node = of_parse_phandle(node, "base", 0);
> + if (WARN_ON(!dfx_node))
What's going on here? The existing bingings don't mention a "base"
phandle, and nothing was added to describe it.
> + return;
> +
> + off = of_get_property(node, "reg", &len);
> + if (WARN_ON(!off))
> + return;
Please don't use of_get_property directly; generally you should use the
existing higher-level helpers like of_proeprty_read_u32().
> +
> + base = of_iomap(dfx_node, 0);
> + if (WARN_ON(!base))
> + return;
> +
> + of_node_put(dfx_node);
> +
> + parent_name = of_clk_get_parent_name(node, 0);
> +
> + clk_data.clk_num = 1;
> +
> + /* clks holds the clock array */
> + clks = kcalloc(clk_data.clk_num, sizeof(struct clk *),
> + GFP_KERNEL);
> + if (WARN_ON(!clks))
> + goto err_unmap;
> + /* corediv holds the clock specific array */
> + corediv = kcalloc(clk_data.clk_num, sizeof(struct clk_corediv),
> + GFP_KERNEL);
> + if (WARN_ON(!corediv))
> + goto err_free_clks;
> +
> + spin_lock_init(&corediv->lock);
> +
> + of_property_read_string_index(node, "clock-output-names",
> + 0, &clk_name);
> +
> + init.num_parents = 1;
> + init.parent_names = &parent_name;
> + init.name = clk_name;
> + init.ops = &ops;
> + init.flags = 0;
> +
> + corediv[0].reg = (void *)((int)base + be32_to_cpu(*off));
I don't understand this, but I guess this has something to do with that
base phandle. Is the corediv clock a sub-component of some "base" clock?
I don't think this binding is the best way of describing that.
Thanks,
Mark.
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 1/5] clk: mvebu: support for 98DX3236 SoC
2017-01-05 13:53 ` Mark Rutland
@ 2017-01-05 23:05 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 23:05 UTC (permalink / raw)
To: linux-arm-kernel
On 06/01/17 03:01, Mark Rutland wrote:
> On Thu, Jan 05, 2017 at 04:36:37PM +1300, Chris Packham wrote:
>> The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
>> the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
>>
>> The clock gating options are a subset of those on the Armada XP.
>>
>> The core clock divider is different to the Armada XP also.
>>
>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>> ---
>> Changes in v2:
>> - Update devicetree binding documentation for new compatible string
>>
>> .../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
>> drivers/clk/mvebu/Makefile | 2 +-
>> drivers/clk/mvebu/armada-xp.c | 42 +++++
>> drivers/clk/mvebu/clk-cpu.c | 33 +++-
>> drivers/clk/mvebu/mv98dx3236-corediv.c | 207 +++++++++++++++++++++
>> 5 files changed, 281 insertions(+), 4 deletions(-)
>> create mode 100644 drivers/clk/mvebu/mv98dx3236-corediv.c
>
>
> It looks like you also need to update
> Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt for the
> addition of "marvell,mv98dx3236-corediv-clock".
Will do.
>
>>
>> diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
>> index 99c214660bdc..7f28506eaee7 100644
>> --- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
>> +++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
>> @@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
>> Required properties:
>> - compatible : shall be one of the following:
>> "marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
>> + "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
>> - reg : Address and length of the clock complex register set, followed
>> by address and length of the PMU DFS registers
>> - #clock-cells : should be set to 1.
>
> [...]
>
>> +static void __init mv98dx3236_corediv_clk_init(struct device_node *node)
>> +{
>> + struct clk_init_data init;
>> + struct clk_corediv *corediv;
>> + struct clk **clks;
>> + void __iomem *base;
>> + const __be32 *off;
>> + const char *parent_name;
>> + const char *clk_name;
>> + int len;
>> + struct device_node *dfx_node;
>> +
>> + dfx_node = of_parse_phandle(node, "base", 0);
>> + if (WARN_ON(!dfx_node))
>
> What's going on here? The existing bingings don't mention a "base"
> phandle, and nothing was added to describe it.
>
>> + return;
>> +
>> + off = of_get_property(node, "reg", &len);
>> + if (WARN_ON(!off))
>> + return;
>
> Please don't use of_get_property directly; generally you should use the
> existing higher-level helpers like of_proeprty_read_u32().
>
>> +
>> + base = of_iomap(dfx_node, 0);
>> + if (WARN_ON(!base))
>> + return;
>> +
>> + of_node_put(dfx_node);
>> +
>> + parent_name = of_clk_get_parent_name(node, 0);
>> +
>> + clk_data.clk_num = 1;
>> +
>> + /* clks holds the clock array */
>> + clks = kcalloc(clk_data.clk_num, sizeof(struct clk *),
>> + GFP_KERNEL);
>> + if (WARN_ON(!clks))
>> + goto err_unmap;
>> + /* corediv holds the clock specific array */
>> + corediv = kcalloc(clk_data.clk_num, sizeof(struct clk_corediv),
>> + GFP_KERNEL);
>> + if (WARN_ON(!corediv))
>> + goto err_free_clks;
>> +
>> + spin_lock_init(&corediv->lock);
>> +
>> + of_property_read_string_index(node, "clock-output-names",
>> + 0, &clk_name);
>> +
>> + init.num_parents = 1;
>> + init.parent_names = &parent_name;
>> + init.name = clk_name;
>> + init.ops = &ops;
>> + init.flags = 0;
>> +
>> + corediv[0].reg = (void *)((int)base + be32_to_cpu(*off));
>
> I don't understand this, but I guess this has something to do with that
> base phandle. Is the corediv clock a sub-component of some "base" clock?
> I don't think this binding is the best way of describing that.
Actually once I've got things setup correctly via the dts I only need
some minor modification to mvebu/clk-corediv.c to handle the differences
in the bit fields used.
>
> Thanks,
> Mark.
>
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
2017-01-05 3:36 ` [PATCHv2 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
@ 2017-01-05 3:36 ` Chris Packham
2017-01-05 4:04 ` Florian Fainelli
2017-01-05 3:36 ` [PATCHv2 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC Chris Packham
` (5 subsequent siblings)
7 siblings, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-05 3:36 UTC (permalink / raw)
To: linux-arm-kernel
Compared to the armada-xp the 98DX3336 uses different registers to set
the boot address for the secondary CPU so a new enable-method is needed.
This will only work if the machine definition doesn't define an overall
smp_ops because there is not currently a way of overriding this from the
device tree if it is set in the machine definition.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Document new enable-method value
- Correct some references from 98DX4521 to 98DX3236
Documentation/devicetree/bindings/arm/cpus.txt | 1 +
.../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/common.h | 1 +
arch/arm/mach-mvebu/platsmp.c | 43 ++++++++++++++
arch/arm/mach-mvebu/pmsu-98dx3236.c | 69 ++++++++++++++++++++++
6 files changed, 133 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index a1bcfeed5f24..3c2fd72d0bf9 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -202,6 +202,7 @@ nodes to be present and contain the properties described below.
"marvell,armada-380-smp"
"marvell,armada-390-smp"
"marvell,armada-xp-smp"
+ "marvell,98dx3236-smp"
"mediatek,mt6589-smp"
"mediatek,mt81xx-tz-smp"
"qcom,gcc-msm8660"
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
new file mode 100644
index 000000000000..8082ba872edd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
@@ -0,0 +1,18 @@
+Resume Control
+--------------
+Available on Marvell SOCs: 98DX3336 and 98DX4251
+
+Required properties:
+
+- compatible: must be "marvell,98dx3336-resume-ctrl"
+
+- reg: Should contain resume control registers location and length
+
+Example:
+
+resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+};
+
+
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 6c6497e80a7b..2a2dd8324fb8 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_MACH_MVEBU_ANY) += system-controller.o mvebu-soc-id.o
ifeq ($(CONFIG_MACH_MVEBU_V7),y)
obj-y += cpu-reset.o board-v7.o coherency.o coherency_ll.o pmsu.o pmsu_ll.o
+obj-y += pmsu-98dx3236.o
obj-$(CONFIG_PM) += pm.o pm-board.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o platsmp-a9.o headsmp-a9.o
diff --git a/arch/arm/mach-mvebu/common.h b/arch/arm/mach-mvebu/common.h
index 6b775492cfad..099dabf23461 100644
--- a/arch/arm/mach-mvebu/common.h
+++ b/arch/arm/mach-mvebu/common.h
@@ -27,4 +27,5 @@ void __iomem *mvebu_get_scu_base(void);
int mvebu_pm_suspend_init(void (*board_pm_enter)(void __iomem *sdram_reg,
u32 srcmd));
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr);
#endif
diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
index 46c742d3bd41..3c9ab9a008ad 100644
--- a/arch/arm/mach-mvebu/platsmp.c
+++ b/arch/arm/mach-mvebu/platsmp.c
@@ -182,5 +182,48 @@ const struct smp_operations armada_xp_smp_ops __initconst = {
#endif
};
+static int mv98dx3236_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ int ret, hw_cpu;
+
+ pr_info("Booting CPU %d\n", cpu);
+
+ hw_cpu = cpu_logical_map(cpu);
+ set_secondary_cpu_clock(hw_cpu);
+ mv98dx3236_resume_set_cpu_boot_addr(hw_cpu,
+ armada_xp_secondary_startup);
+
+ /*
+ * This is needed to wake up CPUs in the offline state after
+ * using CPU hotplug.
+ */
+ arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+
+ /*
+ * This is needed to take secondary CPUs out of reset on the
+ * initial boot.
+ */
+ ret = mvebu_cpu_reset_deassert(hw_cpu);
+ if (ret) {
+ pr_warn("unable to boot CPU: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+struct smp_operations mv98dx3236_smp_ops __initdata = {
+ .smp_init_cpus = armada_xp_smp_init_cpus,
+ .smp_prepare_cpus = armada_xp_smp_prepare_cpus,
+ .smp_boot_secondary = mv98dx3236_boot_secondary,
+ .smp_secondary_init = armada_xp_secondary_init,
+#ifdef CONFIG_HOTPLUG_CPU
+ .cpu_die = armada_xp_cpu_die,
+ .cpu_kill = armada_xp_cpu_kill,
+#endif
+};
+
CPU_METHOD_OF_DECLARE(armada_xp_smp, "marvell,armada-xp-smp",
&armada_xp_smp_ops);
+CPU_METHOD_OF_DECLARE(mv98dx3236_smp, "marvell,98dx3236-smp",
+ &mv98dx3236_smp_ops);
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c b/arch/arm/mach-mvebu/pmsu-98dx3236.c
new file mode 100644
index 000000000000..87ca42ef40c7
--- /dev/null
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -0,0 +1,69 @@
+/**
+ * CPU resume support for 98DX3236 internal CPU (a.k.a. MSYS).
+ */
+
+#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include "common.h"
+
+static void __iomem *mv98dx3236_resume_base;
+#define MV98DX3236_CPU_RESUME_CTRL_OFFSET 0x08
+#define MV98DX3236_CPU_RESUME_ADDR_OFFSET 0x04
+
+static const struct of_device_id of_mv98dx3236_resume_table[] = {
+ {.compatible = "marvell,98dx3336-resume-ctrl",},
+ { /* end of list */ },
+};
+
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
+{
+ WARN_ON(hw_cpu != 1);
+
+ writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
+ writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
+ MV98DX3236_CPU_RESUME_ADDR_OFFSET);
+}
+
+static int __init mv98dx3236_resume_init(void)
+{
+ struct device_node *np;
+ struct resource res;
+ int ret = 0;
+
+ np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
+ if (!np)
+ return 0;
+
+ pr_info("Initializing 98DX3236 Resume\n");
+
+ if (of_address_to_resource(np, 0, &res)) {
+ pr_err("unable to get resource\n");
+ ret = -ENOENT;
+ goto out;
+ }
+
+ if (!request_mem_region(res.start, resource_size(&res),
+ np->full_name)) {
+ pr_err("unable to request region\n");
+ ret = -EBUSY;
+ goto out;
+ }
+
+ mv98dx3236_resume_base = ioremap(res.start, resource_size(&res));
+ if (!mv98dx3236_resume_base) {
+ pr_err("unable to map registers\n");
+ release_mem_region(res.start, resource_size(&res));
+ ret = -ENOMEM;
+ goto out;
+ }
+
+out:
+ of_node_put(np);
+ return ret;
+}
+
+early_initcall(mv98dx3236_resume_init);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-05 3:36 ` [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
@ 2017-01-05 4:04 ` Florian Fainelli
2017-01-05 4:46 ` Chris Packham
0 siblings, 1 reply; 43+ messages in thread
From: Florian Fainelli @ 2017-01-05 4:04 UTC (permalink / raw)
To: linux-arm-kernel
Le 01/04/17 ? 19:36, Chris Packham a ?crit :
> Compared to the armada-xp the 98DX3336 uses different registers to set
> the boot address for the secondary CPU so a new enable-method is needed.
> This will only work if the machine definition doesn't define an overall
> smp_ops because there is not currently a way of overriding this from the
> device tree if it is set in the machine definition.
Not sure I follow you here, in theory, each individual CPU could have a
different enable-method property, and considering how you leverage
existing DTS include files, you should be able to override the DTS with
the appropriate enable-method, or do you have a different problem?
mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
> +{
> + WARN_ON(hw_cpu != 1);
> +
> + writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
> + writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
> + MV98DX3236_CPU_RESUME_ADDR_OFFSET);
I just submitted a patch series that switches such users to
__pa_symbol() instead of virt_to_phys() because this is a kernel image
symbol. For now this will work as-is, but depending on which patch
series makes it first, it may be a good idea to keep this on someone's
TODO list (yours or mine). I do expect having to make a second pass of
conversions anyway.
[1]: https://lkml.org/lkml/2017/1/4/1101
> +}
> +
> +static int __init mv98dx3236_resume_init(void)
> +{
> + struct device_node *np;
> + struct resource res;
> + int ret = 0;
> +
> + np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
> + if (!np)
> + return 0;
> +
> + pr_info("Initializing 98DX3236 Resume\n");
This can be probably be dropped, you should know fairly quickly if this
succeeded or not.
Can't this function be implemented as a smp_ops::smp_init_cpus instead
of having this initialization done at arch_initcall time?
> +
> + if (of_address_to_resource(np, 0, &res)) {
> + pr_err("unable to get resource\n");
> + ret = -ENOENT;
> + goto out;
> + }
> +
> + if (!request_mem_region(res.start, resource_size(&res),
> + np->full_name)) {
> + pr_err("unable to request region\n");
> + ret = -EBUSY;
> + goto out;
> + }
You should be able to use of_io_request_and_map() and here.
--
Florian
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-05 4:04 ` Florian Fainelli
@ 2017-01-05 4:46 ` Chris Packham
2017-01-05 20:49 ` Chris Packham
0 siblings, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-05 4:46 UTC (permalink / raw)
To: linux-arm-kernel
On 05/01/17 17:04, Florian Fainelli wrote:
> Le 01/04/17 ? 19:36, Chris Packham a ?crit :
>> Compared to the armada-xp the 98DX3336 uses different registers to set
>> the boot address for the secondary CPU so a new enable-method is needed.
>> This will only work if the machine definition doesn't define an overall
>> smp_ops because there is not currently a way of overriding this from the
>> device tree if it is set in the machine definition.
>
> Not sure I follow you here, in theory, each individual CPU could have a
> different enable-method property, and considering how you leverage
> existing DTS include files, you should be able to override the DTS with
> the appropriate enable-method, or do you have a different problem?
>
The problem is I can't override the enable method if it's set in the
machine definition. It's because the devicetree is looked up first then
the machine definition overrides it.
Heres an old thread that basically outlines the problem.
http://lists.infradead.org/pipermail/linux-arm-kernel/2014-November/300371.html
I posted a few attempts to work around it but there never really was any
consensus reached.
> mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
>> +{
>> + WARN_ON(hw_cpu != 1);
>> +
>> + writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
>> + writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
>> + MV98DX3236_CPU_RESUME_ADDR_OFFSET);
>
> I just submitted a patch series that switches such users to
> __pa_symbol() instead of virt_to_phys() because this is a kernel image
> symbol. For now this will work as-is, but depending on which patch
> series makes it first, it may be a good idea to keep this on someone's
> TODO list (yours or mine). I do expect having to make a second pass of
> conversions anyway.
>
> [1]: https://lkml.org/lkml/2017/1/4/1101
OK I'll keep that in mind.
>
>> +}
>> +
>> +static int __init mv98dx3236_resume_init(void)
>> +{
>> + struct device_node *np;
>> + struct resource res;
>> + int ret = 0;
>> +
>> + np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
>> + if (!np)
>> + return 0;
>> +
>> + pr_info("Initializing 98DX3236 Resume\n");
>
> This can be probably be dropped, you should know fairly quickly if this
> succeeded or not.
Will do.
>
> Can't this function be implemented as a smp_ops::smp_init_cpus instead
> of having this initialization done at arch_initcall time?
>
I'll look into it. My initial reaction is no because I still need
armada_xp_smp_init_cpus().
>> +
>> + if (of_address_to_resource(np, 0, &res)) {
>> + pr_err("unable to get resource\n");
>> + ret = -ENOENT;
>> + goto out;
>> + }
>> +
>> + if (!request_mem_region(res.start, resource_size(&res),
>> + np->full_name)) {
>> + pr_err("unable to request region\n");
>> + ret = -EBUSY;
>> + goto out;
>> + }
>
> You should be able to use of_io_request_and_map() and here.
>
Will do.
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-05 4:46 ` Chris Packham
@ 2017-01-05 20:49 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 20:49 UTC (permalink / raw)
To: linux-arm-kernel
On 05/01/17 17:46, Chris Packham wrote:
> On 05/01/17 17:04, Florian Fainelli wrote:
>> Le 01/04/17 ? 19:36, Chris Packham a ?crit :
>>> +}
>>> +
>>> +static int __init mv98dx3236_resume_init(void)
>>> +{
>>> + struct device_node *np;
>>> + struct resource res;
>>> + int ret = 0;
>>> +
>>> + np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
>>> + if (!np)
>>> + return 0;
>>
>> Can't this function be implemented as a smp_ops::smp_init_cpus instead
>> of having this initialization done at arch_initcall time?
>>
>
> I'll look into it. My initial reaction is no because I still need
> armada_xp_smp_init_cpus().
>
I looked at this. I could write a mv98dx3236_smp_init_cpus() that calls
armada_xp_smp_init_cpus() and inits the resume controller address. My
original reason for this approach was to parallel mvebu_v7_pmsu_init. I
won't do anything just yet but is there any downside to the current
approach?
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
2017-01-05 3:36 ` [PATCHv2 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
2017-01-05 3:36 ` [PATCHv2 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
@ 2017-01-05 3:36 ` Chris Packham
2017-01-05 3:36 ` [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
` (4 subsequent siblings)
7 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 3:36 UTC (permalink / raw)
To: linux-arm-kernel
From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.
Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- include sdio support for the 98DX4251
.../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++++
drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++++++++++
2 files changed, 201 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
new file mode 100644
index 000000000000..d4e6ecdfc853
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
@@ -0,0 +1,46 @@
+* Marvell 98dx3236 pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage
+
+Required properties:
+- compatible: "marvell,98dx3236-pinctrl" or "marvell,98dx4251-pinctrl"
+- reg: register specifier of MPP registers
+
+This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants
+
+name pins functions
+================================================================================
+mpp0 0 gpio, spi0(mosi), dev(ad8)
+mpp1 1 gpio, spi0(miso), dev(ad9)
+mpp2 2 gpio, spi0(sck), dev(ad10)
+mpp3 3 gpio, spi0(cs0), dev(ad11)
+mpp4 4 gpio, spi0(cs1), smi(mdc), dev(cs0)
+mpp5 5 gpio, pex(rsto), sd0(cmd), dev(bootcs)
+mpp6 6 gpio, sd0(clk), dev(a2)
+mpp7 7 gpio, sd0(d0), dev(ale0)
+mpp8 8 gpio, sd0(d1), dev(ale1)
+mpp9 9 gpio, sd0(d2), dev(ready0)
+mpp10 10 gpio, sd0(d3), dev(ad12)
+mpp11 11 gpio, uart1(rxd), uart0(cts), dev(ad13)
+mpp12 12 gpio, uart1(txd), uart0(rts), dev(ad14)
+mpp13 13 gpio, intr(out), dev(ad15)
+mpp14 14 gpio, i2c0(sck)
+mpp15 15 gpio, i2c0(sda)
+mpp16 16 gpio, dev(oe)
+mpp17 17 gpio, dev(clk)
+mpp18 18 gpio, uart1(txd)
+mpp19 19 gpio, uart1(rxd), dev(rb)
+mpp20 20 gpio, dev(we)
+mpp21 21 gpio, dev(ad0)
+mpp22 22 gpio, dev(ad1)
+mpp23 23 gpio, dev(ad2)
+mpp24 24 gpio, dev(ad3)
+mpp25 25 gpio, dev(ad4)
+mpp26 26 gpio, dev(ad5)
+mpp27 27 gpio, dev(ad6)
+mpp28 28 gpio, dev(ad7)
+mpp29 29 gpio, dev(a0)
+mpp30 30 gpio, dev(a1)
+mpp31 31 gpio, slv_smi(mdc), smi(mdc), dev(we1)
+mpp32 32 gpio, slv_smi(mdio), smi(mdio), dev(cs1)
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
index e4ea71a9d985..554eeae8cd21 100644
--- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
@@ -49,6 +49,10 @@ enum armada_xp_variant {
V_MV78460 = BIT(2),
V_MV78230_PLUS = (V_MV78230 | V_MV78260 | V_MV78460),
V_MV78260_PLUS = (V_MV78260 | V_MV78460),
+ V_98DX3236 = BIT(3),
+ V_98DX3336 = BIT(4),
+ V_98DX4251 = BIT(5),
+ V_98DX3236_PLUS = (V_98DX3236 | V_98DX3336 | V_98DX4251),
};
static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
@@ -360,6 +364,130 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
MPP_VAR_FUNCTION(0x1, "dev", "ad31", V_MV78260_PLUS)),
};
+static struct mvebu_mpp_mode mv98dx3236_mpp_modes[] = {
+ MPP_MODE(0,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "mosi", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad8", V_98DX3236_PLUS)),
+ MPP_MODE(1,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "miso", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad9", V_98DX3236_PLUS)),
+ MPP_MODE(2,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "csk", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad10", V_98DX3236_PLUS)),
+ MPP_MODE(3,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "cs0", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad11", V_98DX3236_PLUS)),
+ MPP_MODE(4,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "cs1", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "cs0", V_98DX3236_PLUS)),
+ MPP_MODE(5,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "pex", "rsto", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "cmd", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "bootcs0", V_98DX3236_PLUS)),
+ MPP_MODE(6,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "clk", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "a2", V_98DX3236_PLUS)),
+ MPP_MODE(7,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d0", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ale0", V_98DX3236_PLUS)),
+ MPP_MODE(8,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d1", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ale1", V_98DX3236_PLUS)),
+ MPP_MODE(9,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d2", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ready0", V_98DX3236_PLUS)),
+ MPP_MODE(10,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d3", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad12", V_98DX3236_PLUS)),
+ MPP_MODE(11,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "uart1", "rxd", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart0", "cts", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad13", V_98DX3236_PLUS)),
+ MPP_MODE(12,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "uart1", "txd", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart0", "rts", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad14", V_98DX3236_PLUS)),
+ MPP_MODE(13,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "intr", "out", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad15", V_98DX3236_PLUS)),
+ MPP_MODE(14,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "i2c0", "sck", V_98DX3236_PLUS)),
+ MPP_MODE(15,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "i2c0", "sda", V_98DX3236_PLUS)),
+ MPP_MODE(16,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "oe", V_98DX3236_PLUS)),
+ MPP_MODE(17,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "clkout", V_98DX3236_PLUS)),
+ MPP_MODE(18,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart1", "txd", V_98DX3236_PLUS)),
+ MPP_MODE(19,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart1", "rxd", V_98DX3236_PLUS)),
+ MPP_MODE(20,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "we0", V_98DX3236_PLUS)),
+ MPP_MODE(21,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad0", V_98DX3236_PLUS)),
+ MPP_MODE(22,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad1", V_98DX3236_PLUS)),
+ MPP_MODE(23,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad2", V_98DX3236_PLUS)),
+ MPP_MODE(24,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad3", V_98DX3236_PLUS)),
+ MPP_MODE(25,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad4", V_98DX3236_PLUS)),
+ MPP_MODE(26,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad5", V_98DX3236_PLUS)),
+ MPP_MODE(27,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad6", V_98DX3236_PLUS)),
+ MPP_MODE(28,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad7", V_98DX3236_PLUS)),
+ MPP_MODE(29,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "a0", V_98DX3236_PLUS)),
+ MPP_MODE(30,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "a1", V_98DX3236_PLUS)),
+ MPP_MODE(31,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "slv_smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "we1", V_98DX3236_PLUS)),
+ MPP_MODE(32,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "slv_smi", "mdio", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdio", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "cs1", V_98DX3236_PLUS)),
+};
+
static struct mvebu_pinctrl_soc_info armada_xp_pinctrl_info;
static const struct of_device_id armada_xp_pinctrl_of_match[] = {
@@ -375,6 +503,14 @@ static const struct of_device_id armada_xp_pinctrl_of_match[] = {
.compatible = "marvell,mv78460-pinctrl",
.data = (void *) V_MV78460,
},
+ {
+ .compatible = "marvell,98dx3236-pinctrl",
+ .data = (void *) V_98DX3236,
+ },
+ {
+ .compatible = "marvell,98dx4251-pinctrl",
+ .data = (void *) V_98DX4251,
+ },
{ },
};
@@ -407,6 +543,14 @@ static struct pinctrl_gpio_range mv78460_mpp_gpio_ranges[] = {
MPP_GPIO_RANGE(2, 64, 64, 3),
};
+static struct mvebu_mpp_ctrl mv98dx3236_mpp_controls[] = {
+ MPP_FUNC_CTRL(0, 32, NULL, armada_xp_mpp_ctrl),
+};
+
+static struct pinctrl_gpio_range mv98dx3236_mpp_gpio_ranges[] = {
+ MPP_GPIO_RANGE(0, 0, 0, 32),
+};
+
static int armada_xp_pinctrl_suspend(struct platform_device *pdev,
pm_message_t state)
{
@@ -488,6 +632,17 @@ static int armada_xp_pinctrl_probe(struct platform_device *pdev)
soc->gpioranges = mv78460_mpp_gpio_ranges;
soc->ngpioranges = ARRAY_SIZE(mv78460_mpp_gpio_ranges);
break;
+ case V_98DX3236:
+ case V_98DX3336:
+ case V_98DX4251:
+ /* fall-through */
+ soc->controls = mv98dx3236_mpp_controls;
+ soc->ncontrols = ARRAY_SIZE(mv98dx3236_mpp_controls);
+ soc->modes = mv98dx3236_mpp_modes;
+ soc->nmodes = mv98dx3236_mpp_controls[0].npins;
+ soc->gpioranges = mv98dx3236_mpp_gpio_ranges;
+ soc->ngpioranges = ARRAY_SIZE(mv98dx3236_mpp_gpio_ranges);
+ break;
}
nregs = DIV_ROUND_UP(soc->nmodes, MVEBU_MPPS_PER_REG);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
` (2 preceding siblings ...)
2017-01-05 3:36 ` [PATCHv2 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC Chris Packham
@ 2017-01-05 3:36 ` Chris Packham
2017-01-05 4:06 ` Florian Fainelli
2017-01-05 13:58 ` Mark Rutland
2017-01-05 3:36 ` [PATCHv2 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards Chris Packham
` (3 subsequent siblings)
7 siblings, 2 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 3:36 UTC (permalink / raw)
To: linux-arm-kernel
The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Update devicetree binding documentation to reflect that 98DX3336 and
984251 are supersets of 98DX3236.
- disable crypto block
- disable sdio for 98DX3236, enable for 98DX4251
.../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 247 +++++++++++++++++++++
arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 78 +++++++
arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 92 ++++++++
4 files changed, 440 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
new file mode 100644
index 000000000000..64e8c73fc5ab
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
@@ -0,0 +1,23 @@
+Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings
+----------------------------------------------------------------------
+
+Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families
+shall have the following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3236"
+
+In addition, boards using the Marvell 98DX3336 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3336"
+
+In addition, boards using the Marvell 98DX4251 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx4251"
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
new file mode 100644
index 000000000000..61bd3acc5cfe
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -0,0 +1,247 @@
+/*
+ * Device Tree Include file for Marvell 98dx3236 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3236 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+ model = "Marvell 98DX3236 SoC";
+ compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "marvell,98dx3236-smp";
+
+ cpu at 0 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <0>;
+ clocks = <&cpuclk 0>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ /*
+ * 98DX3236 has 1 x1 PCIe unit Gen2.0: One unit can be
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ msi-parent = <&mpic>;
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
+ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */>;
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+ };
+
+ internal-regs {
+ coreclk: mvebu-sar at 18230 {
+ compatible = "marvell,mv98dx3236-core-clock";
+ };
+
+ cpuclk: clock-complex at 18700 {
+ compatible = "marvell,mv98dx3236-cpu-clock";
+ };
+
+ corediv-clock at 18740 {
+ compatible = "marvell,mv98dx3236-corediv-clock";
+ reg = <0xf8268 0xc>;
+ base = <&dfx>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
+ xor at 60900 {
+ status = "disabled";
+ };
+
+ crypto at 90000 {
+ status = "disabled";
+ };
+
+ xor at f0900 {
+ status = "disabled";
+ };
+
+ xor at f0800 {
+ compatible = "marvell,orion-xor";
+ reg = <0xf0800 0x100
+ 0xf0a00 0x100>;
+ clocks = <&gateclk 22>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
+
+ /* does not exist */
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ status = "disabled";
+ };
+
+ gpio2: gpio at 18180 { /* rework some properties */
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <1>; /* only gpio #32 */
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <87>;
+ };
+ };
+
+ dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx: dfx at 0 {
+ compatible = "simple-bus";
+ reg = <0 0x100000>;
+ };
+ };
+
+ switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ compatible = "marvell,98dx3236-pinctrl";
+
+ spi0_pins: spi0-pins {
+ marvell,pins = "mpp0", "mpp1",
+ "mpp2", "mpp3";
+ marvell,function = "spi0";
+ };
+};
+
+&sdio {
+ status = "disabled";
+};
+
+&crypto_sram0 {
+ status = "disabled";
+};
+
+&crypto_sram1 {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
new file mode 100644
index 000000000000..9c9aa565fd82
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
@@ -0,0 +1,78 @@
+/*
+ * Device Tree Include file for Marvell 98dx3336 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3336 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+ model = "Marvell 98DX3336 SoC";
+ compatible = "marvell,armadaxp-98dx3336", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ cpus {
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+ };
+ };
+
+ switch {
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3336";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
new file mode 100644
index 000000000000..5f7edc23d5ae
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -0,0 +1,92 @@
+/*
+ * Device Tree Include file for Marvell 98dx4521 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx4521 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+ model = "Marvell 98DX4251 SoC";
+ compatible = "marvell,armadaxp-98dx4521", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ cpus {
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+ };
+ };
+
+ switch {
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx4521";
+ };
+ };
+ };
+};
+
+&sdio {
+ status = "okay";
+};
+
+&pinctrl {
+ compatible = "marvell,98dx4251-pinctrl";
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp5", "mpp6", "mpp7",
+ "mpp8", "mpp9", "mpp10";
+ marvell,function = "sd0";
+ };
+};
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-05 3:36 ` [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
@ 2017-01-05 4:06 ` Florian Fainelli
2017-01-05 4:34 ` Chris Packham
2017-01-05 13:58 ` Mark Rutland
1 sibling, 1 reply; 43+ messages in thread
From: Florian Fainelli @ 2017-01-05 4:06 UTC (permalink / raw)
To: linux-arm-kernel
Le 01/04/17 ? 19:36, Chris Packham a ?crit :
> The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
> with integrated CPUs. They are similar to the Armada XP SoCs but have
> different I/O interfaces.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> +
> + switch {
> + packet-processor at 0 {
> + compatible = "marvell,prestera-98dx4521";
> + };
> + };
This may be a bit premature if you are not providing a binding document
for this sub-node, you might as well add it once you also add a
corresponding driver (or if this will remain out of tree, at least
submitting a separate binding document).
Also, if this node's unit address is 0, you would expect at least a reg
property whose address cell is 0 to be present.
--
Florian
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-05 4:06 ` Florian Fainelli
@ 2017-01-05 4:34 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 4:34 UTC (permalink / raw)
To: linux-arm-kernel
On 05/01/17 17:06, Florian Fainelli wrote:
> Le 01/04/17 ? 19:36, Chris Packham a ?crit :
>> The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
>> with integrated CPUs. They are similar to the Armada XP SoCs but have
>> different I/O interfaces.
>>
>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>> ---
>> +
>> + switch {
>> + packet-processor at 0 {
>> + compatible = "marvell,prestera-98dx4521";
>> + };
>> + };
>
> This may be a bit premature if you are not providing a binding document
> for this sub-node, you might as well add it once you also add a
> corresponding driver (or if this will remain out of tree, at least
> submitting a separate binding document).
I also see that I made a typo 4521 should be 4251.
The driver that uses this is an out of tree one so I will add a binding
document for it for now.
It wouldn't he hard to whip up a simple uio based driver that provides
mmap access to the switch register space so I might look at that if I
get time. It would be useful for testing if nothing else.
>
> Also, if this node's unit address is 0, you would expect at least a reg
> property whose address cell is 0 to be present.
>
The reg property is in the base 98dx3236 dsti file. The 3 devices have
the same IO footprint but the switching functionality is quite different
between them hence the different compatible strings (all of which I need
to add binding documentation for). I guess I could make the 3236 entry
pp0: packet-processor at 0 {
compatible = "marvell,prestera-98dx3236";
reg = <0 0x4000000>;
...
}
Then the 3336 and 4251 could just override the compatible string
&pp0 {
compatible = "marvell,prestera-98dx4251";
};
Would that be clearer?
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-05 3:36 ` [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
2017-01-05 4:06 ` Florian Fainelli
@ 2017-01-05 13:58 ` Mark Rutland
2017-01-05 20:10 ` Chris Packham
1 sibling, 1 reply; 43+ messages in thread
From: Mark Rutland @ 2017-01-05 13:58 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Jan 05, 2017 at 04:36:40PM +1300, Chris Packham wrote:
> + internal-regs {
> + coreclk: mvebu-sar at 18230 {
> + compatible = "marvell,mv98dx3236-core-clock";
> + };
> +
> + cpuclk: clock-complex at 18700 {
> + compatible = "marvell,mv98dx3236-cpu-clock";
> + };
> +
> + corediv-clock at 18740 {
> + compatible = "marvell,mv98dx3236-corediv-clock";
> + reg = <0xf8268 0xc>;
> + base = <&dfx>;
> + #clock-cells = <1>;
> + clocks = <&mainpll>;
> + clock-output-names = "nand";
> + };
[...]
> + };
> +
> + dfx-registers {
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
> +
> + dfx: dfx at 0 {
> + compatible = "simple-bus";
> + reg = <0 0x100000>;
> + };
> + };
What is this dfx-registers, exactly? It has no children, so why is it a
simple-bus?
>From the above, and the patch adding the corediv driver, it looks like
the corediv-clock actually lives in this block, so I don't understand
why the corediv-clock is sitting in internal-regs with a sideband
reference to dfx.
Thanks,
Mark.
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-05 13:58 ` Mark Rutland
@ 2017-01-05 20:10 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 20:10 UTC (permalink / raw)
To: linux-arm-kernel
On 06/01/17 02:59, Mark Rutland wrote:
> On Thu, Jan 05, 2017 at 04:36:40PM +1300, Chris Packham wrote:
>> + internal-regs {
>> + coreclk: mvebu-sar at 18230 {
>> + compatible = "marvell,mv98dx3236-core-clock";
>> + };
>> +
>> + cpuclk: clock-complex at 18700 {
>> + compatible = "marvell,mv98dx3236-cpu-clock";
>> + };
>> +
>> + corediv-clock at 18740 {
>> + compatible = "marvell,mv98dx3236-corediv-clock";
>> + reg = <0xf8268 0xc>;
>> + base = <&dfx>;
>> + #clock-cells = <1>;
>> + clocks = <&mainpll>;
>> + clock-output-names = "nand";
>> + };
>
> [...]
>
>> + };
>> +
>> + dfx-registers {
>> + compatible = "simple-bus";
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
>> +
>> + dfx: dfx at 0 {
>> + compatible = "simple-bus";
>> + reg = <0 0x100000>;
>> + };
>> + };
>
> What is this dfx-registers, exactly?
I've been trying to get that info out of Marvell for a while I'm not
even sure what the "DFX" acronym stands for. The Armdada 38x also has a
thing called "DFX" but it seems to be quite different to this one. From
what I can tell it contains common elements used by both the CPU and
switch chip so there are things related to clocking and IO pad
configuration. It is necessary for both the switch and CPU to have a
handle to access it.
> It has no children, so why is it a
> simple-bus?
>
> From the above, and the patch adding the corediv driver, it looks like
> the corediv-clock actually lives in this block, so I don't understand
> why the corediv-clock is sitting in internal-regs with a sideband
> reference to dfx.
Yeah I think the corediv-clock should be a child of this node. I'll move
it there.
>
> Thanks,
> Mark.
>
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
` (3 preceding siblings ...)
2017-01-05 3:36 ` [PATCHv2 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
@ 2017-01-05 3:36 ` Chris Packham
2017-01-05 4:07 ` [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Florian Fainelli
` (2 subsequent siblings)
7 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 3:36 UTC (permalink / raw)
To: linux-arm-kernel
These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Chaqnges in v2:
- None
arch/arm/boot/dts/db-dxbc2.dts | 159 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++++++++++++++++++++++++
2 files changed, 314 insertions(+)
create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
diff --git a/arch/arm/boot/dts/db-dxbc2.dts b/arch/arm/boot/dts/db-dxbc2.dts
new file mode 100644
index 000000000000..f56786cea5f8
--- /dev/null
+++ b/arch/arm/boot/dts/db-dxbc2.dts
@@ -0,0 +1,159 @@
+/*
+ * Device Tree file for DB-DXBC2 board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx4251.dtsi"
+
+/ {
+ model = "Marvell Bobcat2 Evaluation Board";
+ compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+ serial at 12100 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ clock-frequency = <100000>;
+ status = "okay";
+ };
+
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ broken-cd;
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+
+ partition at u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition at u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition at unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
diff --git a/arch/arm/boot/dts/db-xc3-24g4xg.dts b/arch/arm/boot/dts/db-xc3-24g4xg.dts
new file mode 100644
index 000000000000..5eb89ffb9a7d
--- /dev/null
+++ b/arch/arm/boot/dts/db-xc3-24g4xg.dts
@@ -0,0 +1,155 @@
+/*
+ * Device Tree file for DB-XC3-24G4XG board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3336.dtsi"
+
+/ {
+ model = "DB-XC3-24G4XG";
+ compatible = "marvell,db-xc3-24g4xg", "marvell,armadaxp-98dx3336", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+ serial at 12100 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ clock-frequency = <100000>;
+ status = "okay";
+ };
+
+ mvsdio at d4000 {
+ status = "disabled";
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+
+ partition at u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition at u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition at unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
` (4 preceding siblings ...)
2017-01-05 3:36 ` [PATCHv2 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards Chris Packham
@ 2017-01-05 4:07 ` Florian Fainelli
2017-01-05 4:24 ` Chris Packham
2017-01-05 14:09 ` Marcin Wojtas
2017-01-06 4:14 ` Chris Packham
7 siblings, 1 reply; 43+ messages in thread
From: Florian Fainelli @ 2017-01-05 4:07 UTC (permalink / raw)
To: linux-arm-kernel
Le 01/04/17 ? 19:36, Chris Packham a ?crit :
> The 98DX3236, 98DX3336 and 98DX4251 are a set of switch ASICs with
> integrated CPUs. They CPU block is common within these product lines and
> (as far as I can tell/have been told) is based on the Armada XP. There
> are a few differences due to the fact they have to squeeze the CPU into
> the same package as the switch.
It's really great to see these changes, do you have a plan to also add
support for the integrated switch using a DSA/switchdev driver?
Thanks!
--
Florian
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 4:07 ` [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Florian Fainelli
@ 2017-01-05 4:24 ` Chris Packham
2017-01-05 13:09 ` Andrew Lunn
0 siblings, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-05 4:24 UTC (permalink / raw)
To: linux-arm-kernel
On 05/01/17 17:07, Florian Fainelli wrote:
> Le 01/04/17 ? 19:36, Chris Packham a ?crit :
>> The 98DX3236, 98DX3336 and 98DX4251 are a set of switch ASICs with
>> integrated CPUs. They CPU block is common within these product lines and
>> (as far as I can tell/have been told) is based on the Armada XP. There
>> are a few differences due to the fact they have to squeeze the CPU into
>> the same package as the switch.
>
> It's really great to see these changes, do you have a plan to also add
> support for the integrated switch using a DSA/switchdev driver?
I'd love to see a switchdev driver but it's a huge task (and no I'm not
committing to writing it). As it stands Marvell ship a switch SDK
largely executes in userspace with a small kernel module providing some
linkage to the underlying hardware.
We (a few of us here at Allied Telesis NZ) have discussed switchdev and
how we get from using Marvell's SDK in our products to using switchdev
proper.
The first step would probably be some kind of trampoline driver which
communicates with a userspace helper to do the actual work.
Alternatively there is some support in Marvell's SDK for compilation as
a binary blob so a proprietary kernel module is another option. Neither
of these are particularly nice in a free software world.
A full "free" implementation would be a large undertaking. Ideally I'd
like to see Marvell involved with producing one but so far they've not
been interested whenever I've brought it up.
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 4:24 ` Chris Packham
@ 2017-01-05 13:09 ` Andrew Lunn
2017-01-05 14:07 ` Marcin Wojtas
2017-01-05 19:46 ` Chris Packham
0 siblings, 2 replies; 43+ messages in thread
From: Andrew Lunn @ 2017-01-05 13:09 UTC (permalink / raw)
To: linux-arm-kernel
> I'd love to see a switchdev driver but it's a huge task (and no I'm not
> committing to writing it). As it stands Marvell ship a switch SDK
> largely executes in userspace with a small kernel module providing some
> linkage to the underlying hardware.
Is there any similarity to the mv88e6xxx family?
If it was similar registers, just a different access mechanising, we
could probably extend the mv88e6xxx to support MMIO as well as MDIO.
Andrew
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 13:09 ` Andrew Lunn
@ 2017-01-05 14:07 ` Marcin Wojtas
2017-01-05 19:46 ` Chris Packham
1 sibling, 0 replies; 43+ messages in thread
From: Marcin Wojtas @ 2017-01-05 14:07 UTC (permalink / raw)
To: linux-arm-kernel
Hi Andrew,
2017-01-05 14:09 GMT+01:00 Andrew Lunn <andrew@lunn.ch>:
>> I'd love to see a switchdev driver but it's a huge task (and no I'm not
>> committing to writing it). As it stands Marvell ship a switch SDK
>> largely executes in userspace with a small kernel module providing some
>> linkage to the underlying hardware.
>
> Is there any similarity to the mv88e6xxx family?
Prestera switches (they are sold as standalone devices and with
integrated CPU's, like ones submitted) are as far from mv88e6xxx as
possible. There are various mix of 1/2.5/10/40G ports, depending on
model.
>
> If it was similar registers, just a different access mechanising, we
> could probably extend the mv88e6xxx to support MMIO as well as MDIO.
>
The difference is huge, nothing existing in the mainline can fit. The
driver, that exposes resources to the userspace SDK (called CPSS, it's
huge and complex piece of code) is existing in Marvell internal
branches (kernel v4.4 is the latest one), but I doubt such solution
(despite it's really small) is upstreamable. I believe it can be
shipped to the customers along with the SDK as a kernel module. Having
the CPU's support in the mainline is IMO sufficient.
Best regards,
Marcin
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 13:09 ` Andrew Lunn
2017-01-05 14:07 ` Marcin Wojtas
@ 2017-01-05 19:46 ` Chris Packham
2017-01-05 19:52 ` Florian Fainelli
1 sibling, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-05 19:46 UTC (permalink / raw)
To: linux-arm-kernel
On 06/01/17 02:10, Andrew Lunn wrote:
>> I'd love to see a switchdev driver but it's a huge task (and no I'm not
>> committing to writing it). As it stands Marvell ship a switch SDK
>> largely executes in userspace with a small kernel module providing some
>> linkage to the underlying hardware.
>
> Is there any similarity to the mv88e6xxx family?
>
> If it was similar registers, just a different access mechanising, we
> could probably extend the mv88e6xxx to support MMIO as well as MDIO.
No the prestera family of devices are considerably more powerful (and
complex) than the linkstreet devices.
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 19:46 ` Chris Packham
@ 2017-01-05 19:52 ` Florian Fainelli
0 siblings, 0 replies; 43+ messages in thread
From: Florian Fainelli @ 2017-01-05 19:52 UTC (permalink / raw)
To: linux-arm-kernel
On 01/05/2017 11:46 AM, Chris Packham wrote:
> On 06/01/17 02:10, Andrew Lunn wrote:
>>> I'd love to see a switchdev driver but it's a huge task (and no I'm not
>>> committing to writing it). As it stands Marvell ship a switch SDK
>>> largely executes in userspace with a small kernel module providing some
>>> linkage to the underlying hardware.
>>
>> Is there any similarity to the mv88e6xxx family?
>>
>> If it was similar registers, just a different access mechanising, we
>> could probably extend the mv88e6xxx to support MMIO as well as MDIO.
>
> No the prestera family of devices are considerably more powerful (and
> complex) than the linkstreet devices.
I see, we have a similar situation with some of the Broadcom SoCs, the
BCM534xx/BCM5334x have a completely different integrated switching
engine that is not roboswitch compatible.
Thanks for the information, this is still valuable to have this
supported upstream.
--
Florian
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
` (5 preceding siblings ...)
2017-01-05 4:07 ` [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Florian Fainelli
@ 2017-01-05 14:09 ` Marcin Wojtas
2017-01-05 20:02 ` Chris Packham
2017-01-06 4:14 ` Chris Packham
7 siblings, 1 reply; 43+ messages in thread
From: Marcin Wojtas @ 2017-01-05 14:09 UTC (permalink / raw)
To: linux-arm-kernel
Hi Chris,
Thanks a lot for your work and v2. Can you please add changelog
between patchset versions in your cover letter?
Best regards,
Marcin
2017-01-05 4:36 GMT+01:00 Chris Packham <chris.packham@alliedtelesis.co.nz>:
> The 98DX3236, 98DX3336 and 98DX4251 are a set of switch ASICs with
> integrated CPUs. They CPU block is common within these product lines and
> (as far as I can tell/have been told) is based on the Armada XP. There
> are a few differences due to the fact they have to squeeze the CPU into
> the same package as the switch.
>
> Chris Packham (4):
> clk: mvebu: support for 98DX3236 SoC
> arm: mvebu: support for SMP on 98DX3336 SoC
> arm: mvebu: Add device tree for 98DX3236 SoCs
> arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
>
> Kalyan Kinthada (1):
> pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
>
> Documentation/devicetree/bindings/arm/cpus.txt | 1 +
> .../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++
> .../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
> .../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
> .../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++
> arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 247 +++++++++++++++++++++
> arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 78 +++++++
> arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 92 ++++++++
> arch/arm/boot/dts/db-dxbc2.dts | 159 +++++++++++++
> arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++
> arch/arm/mach-mvebu/Makefile | 1 +
> arch/arm/mach-mvebu/common.h | 1 +
> arch/arm/mach-mvebu/platsmp.c | 43 ++++
> arch/arm/mach-mvebu/pmsu-98dx3236.c | 69 ++++++
> drivers/clk/mvebu/Makefile | 2 +-
> drivers/clk/mvebu/armada-xp.c | 42 ++++
> drivers/clk/mvebu/clk-cpu.c | 33 ++-
> drivers/clk/mvebu/mv98dx3236-corediv.c | 207 +++++++++++++++++
> drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++
> 19 files changed, 1369 insertions(+), 4 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
> create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
> create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
> create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
> create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
> create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
> create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
> create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
> create mode 100644 drivers/clk/mvebu/mv98dx3236-corediv.c
>
> --
> 2.11.0.24.ge6920cf
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 14:09 ` Marcin Wojtas
@ 2017-01-05 20:02 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-05 20:02 UTC (permalink / raw)
To: linux-arm-kernel
On 06/01/17 03:09, Marcin Wojtas wrote:
> Hi Chris,
>
> Thanks a lot for your work and v2. Can you please add changelog
> between patchset versions in your cover letter?
Will do for v3. I did actually include a changelog in the individual
patches but I can collate that here.
clk: mvebu: support for 98DX3236 SoC
- Update devicetree binding documentation for new compatible string
arm: mvebu: support for SMP on 98DX3336 SoC
- Document new enable-method value
- Correct some references from 98DX4521 to 98DX3236
pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
- include sdio support for the 98DX4251
arm: mvebu: Add device tree for 98DX3236 SoCs
- Update devicetree binding documentation to reflect that 98DX3336 and
984251 are supersets of 98DX3236.
- disable crypto block
- disable sdio for 98DX3236, enable for 98DX4251
arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
- None
Here's the interdiff
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt
b/Documentation/devicetree/bindings/arm/cpus.txt
index a1bcfeed5f24..3c2fd72d0bf9 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -202,6 +202,7 @@ nodes to be present and contain the properties
described below.
"marvell,armada-380-smp"
"marvell,armada-390-smp"
"marvell,armada-xp-smp"
+ "marvell,98dx3236-smp"
"mediatek,mt6589-smp"
"mediatek,mt81xx-tz-smp"
"qcom,gcc-msm8660"
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
index e7dc9b2dd90b..64e8c73fc5ab 100644
--- a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
@@ -6,5 +6,18 @@ shall have the following property:
Required root node property:
-compatible: one of "marvell,armadaxp-98dx3236", "marvell,armadaxp-98dx3336"
- or "marvell,armadaxp-98dx4251"
+compatible: must contain "marvell,armadaxp-98dx3236"
+
+In addition, boards using the Marvell 98DX3336 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3336"
+
+In addition, boards using the Marvell 98DX4251 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx4251"
diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
index 99c214660bdc..7f28506eaee7 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
@@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU
platforms
Required properties:
- compatible : shall be one of the following:
"marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
+ "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
- reg : Address and length of the clock complex register set, followed
by address and length of the PMU DFS registers
- #clock-cells : should be set to 1.
diff --git
a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
index 34c1e380adaa..d4e6ecdfc853 100644
---
a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
+++
b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
@@ -4,7 +4,7 @@ Please refer to marvell,mvebu-pinctrl.txt in this
directory for common binding
part and usage
Required properties:
-- compatible: "marvell,98dx3236-pinctrl"
+- compatible: "marvell,98dx3236-pinctrl" or "marvell,98dx4251-pinctrl"
- reg: register specifier of MPP registers
This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants
@@ -16,12 +16,12 @@ mpp1 1 gpio, spi0(miso), dev(ad9)
mpp2 2 gpio, spi0(sck), dev(ad10)
mpp3 3 gpio, spi0(cs0), dev(ad11)
mpp4 4 gpio, spi0(cs1), smi(mdc), dev(cs0)
-mpp5 5 gpio, pex(rsto), dev(bootcs)
-mpp6 6 gpio, dev(a2)
-mpp7 7 gpio, dev(ale0)
-mpp8 8 gpio, dev(ale1)
-mpp9 9 gpio, dev(ready0)
-mpp10 10 gpio, dev(ad12)
+mpp5 5 gpio, pex(rsto), sd0(cmd), dev(bootcs)
+mpp6 6 gpio, sd0(clk), dev(a2)
+mpp7 7 gpio, sd0(d0), dev(ale0)
+mpp8 8 gpio, sd0(d1), dev(ale1)
+mpp9 9 gpio, sd0(d2), dev(ready0)
+mpp10 10 gpio, sd0(d3), dev(ad12)
mpp11 11 gpio, uart1(rxd), uart0(cts), dev(ad13)
mpp12 12 gpio, uart1(txd), uart0(rts), dev(ad14)
mpp13 13 gpio, intr(out), dev(ad15)
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
index bac53f8b44af..61bd3acc5cfe 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -138,6 +138,10 @@
status = "disabled";
};
+ crypto at 90000 {
+ status = "disabled";
+ };
+
xor at f0900 {
status = "disabled";
};
@@ -229,3 +233,15 @@
marvell,function = "spi0";
};
};
+
+&sdio {
+ status = "disabled";
+};
+
+&crypto_sram0 {
+ status = "disabled";
+};
+
+&crypto_sram1 {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
index 5d1da8513fae..5f7edc23d5ae 100644
--- a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -76,3 +76,17 @@
};
};
};
+
+&sdio {
+ status = "okay";
+};
+
+&pinctrl {
+ compatible = "marvell,98dx4251-pinctrl";
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp5", "mpp6", "mpp7",
+ "mpp8", "mpp9", "mpp10";
+ marvell,function = "sd0";
+ };
+};
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c
b/arch/arm/mach-mvebu/pmsu-98dx3236.c
index fadc81d0c051..87ca42ef40c7 100644
--- a/arch/arm/mach-mvebu/pmsu-98dx3236.c
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -1,5 +1,5 @@
/**
- * CPU resume support for 98DX4521 internal CPU (a.k.a. MSYS).
+ * CPU resume support for 98DX3236 internal CPU (a.k.a. MSYS).
*/
#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
@@ -38,7 +38,7 @@ static int __init mv98dx3236_resume_init(void)
if (!np)
return 0;
- pr_info("Initializing 98DX4521 Resume\n");
+ pr_info("Initializing 98DX3236 Resume\n");
if (of_address_to_resource(np, 0, &res)) {
pr_err("unable to get resource\n");
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
index 2586903c59f0..554eeae8cd21 100644
--- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
@@ -389,21 +389,27 @@ static struct mvebu_mpp_mode
mv98dx3236_mpp_modes[] = {
MPP_MODE(5,
MPP_VAR_FUNCTION(0x0, "gpio", NULL,
V_98DX3236_PLUS),
MPP_VAR_FUNCTION(0x1, "pex", "rsto",
V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "cmd", V_98DX4251),
MPP_VAR_FUNCTION(0x4, "dev", "bootcs0",
V_98DX3236_PLUS)),
MPP_MODE(6,
MPP_VAR_FUNCTION(0x0, "gpo", NULL,
V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "clk", V_98DX4251),
MPP_VAR_FUNCTION(0x4, "dev", "a2",
V_98DX3236_PLUS)),
MPP_MODE(7,
MPP_VAR_FUNCTION(0x0, "gpio", NULL,
V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d0", V_98DX4251),
MPP_VAR_FUNCTION(0x4, "dev", "ale0",
V_98DX3236_PLUS)),
MPP_MODE(8,
MPP_VAR_FUNCTION(0x0, "gpio", NULL,
V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d1", V_98DX4251),
MPP_VAR_FUNCTION(0x4, "dev", "ale1",
V_98DX3236_PLUS)),
MPP_MODE(9,
MPP_VAR_FUNCTION(0x0, "gpio", NULL,
V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d2", V_98DX4251),
MPP_VAR_FUNCTION(0x4, "dev", "ready0",
V_98DX3236_PLUS)),
MPP_MODE(10,
MPP_VAR_FUNCTION(0x0, "gpio", NULL,
V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d3", V_98DX4251),
MPP_VAR_FUNCTION(0x4, "dev", "ad12",
V_98DX3236_PLUS)),
MPP_MODE(11,
MPP_VAR_FUNCTION(0x0, "gpio", NULL,
V_98DX3236_PLUS),
@@ -501,6 +507,10 @@ static const struct of_device_id
armada_xp_pinctrl_of_match[] = {
.compatible = "marvell,98dx3236-pinctrl",
.data = (void *) V_98DX3236,
},
+ {
+ .compatible = "marvell,98dx4251-pinctrl",
+ .data = (void *) V_98DX4251,
+ },
{ },
};
>
> Best regards,
> Marcin
>
> 2017-01-05 4:36 GMT+01:00 Chris Packham <chris.packham@alliedtelesis.co.nz>:
>> The 98DX3236, 98DX3336 and 98DX4251 are a set of switch ASICs with
>> integrated CPUs. They CPU block is common within these product lines and
>> (as far as I can tell/have been told) is based on the Armada XP. There
>> are a few differences due to the fact they have to squeeze the CPU into
>> the same package as the switch.
>>
>> Chris Packham (4):
>> clk: mvebu: support for 98DX3236 SoC
>> arm: mvebu: support for SMP on 98DX3336 SoC
>> arm: mvebu: Add device tree for 98DX3236 SoCs
>> arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
>>
>> Kalyan Kinthada (1):
>> pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
>>
>> Documentation/devicetree/bindings/arm/cpus.txt | 1 +
>> .../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++
>> .../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
>> .../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
>> .../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++
>> arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 247 +++++++++++++++++++++
>> arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 78 +++++++
>> arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 92 ++++++++
>> arch/arm/boot/dts/db-dxbc2.dts | 159 +++++++++++++
>> arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++
>> arch/arm/mach-mvebu/Makefile | 1 +
>> arch/arm/mach-mvebu/common.h | 1 +
>> arch/arm/mach-mvebu/platsmp.c | 43 ++++
>> arch/arm/mach-mvebu/pmsu-98dx3236.c | 69 ++++++
>> drivers/clk/mvebu/Makefile | 2 +-
>> drivers/clk/mvebu/armada-xp.c | 42 ++++
>> drivers/clk/mvebu/clk-cpu.c | 33 ++-
>> drivers/clk/mvebu/mv98dx3236-corediv.c | 207 +++++++++++++++++
>> drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++
>> 19 files changed, 1369 insertions(+), 4 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
>> create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
>> create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
>> create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
>> create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
>> create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
>> create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
>> create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
>> create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
>> create mode 100644 drivers/clk/mvebu/mv98dx3236-corediv.c
>>
>> --
>> 2.11.0.24.ge6920cf
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
^ permalink raw reply related [flat|nested] 43+ messages in thread
* [PATCHv2 0/5] Support for Marvell switches with integrated CPUs
2017-01-05 3:36 [PATCHv2 0/5] Support for Marvell switches with integrated CPUs Chris Packham
` (6 preceding siblings ...)
2017-01-05 14:09 ` Marcin Wojtas
@ 2017-01-06 4:14 ` Chris Packham
2017-01-06 4:14 ` [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
` (4 more replies)
7 siblings, 5 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
The 98DX3236, 98DX3336 and 98DX4251 are a set of switch ASICs with
integrated CPUs. They CPU block is common within these product lines and
(as far as I can tell/have been told) is based on the Armada XP. There
are a few differences due to the fact they have to squeeze the CPU into
the same package as the switch.
Chris Packham (4):
clk: mvebu: support for 98DX3236 SoC
Changes in v2:
- Update devicetree binding documentation for new compatible string
Changes in v3:
- Add 98dx3236 support to mvebu/clk-corediv.c rather than creating a
new driver.
- Document mv98dx3236-corediv-clock binding
arm: mvebu: support for SMP on 98DX3336 SoC
Changes in v2:
- Document new enable-method value
- Correct some references from 98DX4521 to 98DX3236
Changes in v3:
- Simplify mv98dx3236_resume_init by using of_io_request_and_map()
arm: mvebu: Add device tree for 98DX3236 SoCs
Changes in v2:
- Update devicetree binding documentation to reflect that 98DX3336 and
984251 are supersets of 98DX3236.
- disable crypto block
- disable sdio for 98DX3236, enable for 98DX4251
Changes in v3:
- fix typo 4521 -> 4251
- document prestera bindings
- rework corediv-clock binding
- add label to packet processor node
- add new compativle string for DFX server
arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
Changes in v2/v3:
- none
Kalyan Kinthada (1):
pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
Changes in v2:
- include sdio support for the 98DX4251
Changes in v3:
- None
Documentation/devicetree/bindings/arm/cpus.txt | 1 +
.../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++
.../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
.../bindings/clock/mvebu-corediv-clock.txt | 1 +
.../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
.../devicetree/bindings/net/marvell,prestera.txt | 50 ++++
.../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++
arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 254 +++++++++++++++++++++
arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 76 ++++++
arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 90 ++++++++
arch/arm/boot/dts/db-dxbc2.dts | 159 +++++++++++++
arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/common.h | 1 +
arch/arm/mach-mvebu/platsmp.c | 43 ++++
arch/arm/mach-mvebu/pmsu-98dx3236.c | 52 +++++
drivers/clk/mvebu/armada-xp.c | 42 ++++
drivers/clk/mvebu/clk-corediv.c | 23 ++
drivers/clk/mvebu/clk-cpu.c | 31 ++-
drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++
20 files changed, 1220 insertions(+), 2 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
create mode 100644 Documentation/devicetree/bindings/net/marvell,prestera.txt
create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
Interdiff to v2:
diff --git
a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
index 520562a7dc2a..c7b4e3a6b2c6 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
@@ -7,6 +7,7 @@ Required properties:
- compatible : must be "marvell,armada-370-corediv-clock",
"marvell,armada-375-corediv-clock",
"marvell,armada-380-corediv-clock",
+ "marvell,mv98dx3236-corediv-clock",
- reg : must be the register address of Core Divider control register
- #clock-cells : from common clock binding; shall be set to 1
diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt
b/Documentation/devicetree/bindings/net/marvell,prestera.txt
new file mode 100644
index 000000000000..5fbab29718e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt
@@ -0,0 +1,50 @@
+Marvell Prestera Switch Chip bindings
+-------------------------------------
+
+Required properties:
+- compatible: one of the following
+ "marvell,prestera-98dx3236",
+ "marvell,prestera-98dx3336",
+ "marvell,prestera-98dx4251",
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+
+Optional properties:
+- dfx: phandle reference to the "DFX Server" node
+
+Example:
+
+switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+};
+
+DFX Server bindings
+-------------------
+
+Required properties:
+- compatible: must be "marvell,dfx-server"
+- reg: address and length of the register set for the device.
+
+Example:
+
+dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx: dfx at 0 {
+ compatible = "marvell,dfx-server";
+ reg = <0 0x100000>;
+ };
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
index 61bd3acc5cfe..4b7b2fe3b682 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -126,12 +126,7 @@
};
corediv-clock at 18740 {
- compatible =
"marvell,mv98dx3236-corediv-clock";
- reg = <0xf8268 0xc>;
- base = <&dfx>;
- #clock-cells = <1>;
- clocks = <&mainpll>;
- clock-output-names = "nand";
+ status = "disabled";
};
xor at 60900 {
@@ -194,6 +189,10 @@
#interrupt-cells = <2>;
interrupts = <87>;
};
+
+ nand: nand at d0000 {
+ clocks = <&dfx_coredivclk 0>;
+ };
};
dfx-registers {
@@ -202,8 +201,16 @@
#size-cells = <1>;
ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+ dfx_coredivclk: corediv-clock at f8268 {
+ compatible =
"marvell,mv98dx3236-corediv-clock";
+ reg = <0xf8268 0xc>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
dfx: dfx at 0 {
- compatible = "simple-bus";
+ compatible = "marvell,dfx-server";
reg = <0 0x100000>;
};
};
@@ -214,7 +221,7 @@
#size-cells = <1>;
ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
- packet-processor at 0 {
+ pp0: packet-processor at 0 {
compatible =
"marvell,prestera-98dx3236";
reg = <0 0x4000000>;
interrupts = <33>, <34>, <35>;
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
index 9c9aa565fd82..a9b0f47f8df9 100644
--- a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
@@ -68,11 +68,9 @@
reg = <0x20980 0x10>;
};
};
-
- switch {
- packet-processor at 0 {
- compatible =
"marvell,prestera-98dx3336";
- };
- };
};
};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx3336";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
index 5f7edc23d5ae..446e6e65ec59 100644
--- a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -68,12 +68,6 @@
reg = <0x20980 0x10>;
};
};
-
- switch {
- packet-processor at 0 {
- compatible =
"marvell,prestera-98dx4521";
- };
- };
};
};
@@ -90,3 +84,7 @@
marvell,function = "sd0";
};
};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx4251";
+};
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c
b/arch/arm/mach-mvebu/pmsu-98dx3236.c
index 87ca42ef40c7..1052674dd439 100644
--- a/arch/arm/mach-mvebu/pmsu-98dx3236.c
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -31,39 +31,22 @@ void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu,
void *boot_addr)
static int __init mv98dx3236_resume_init(void)
{
struct device_node *np;
- struct resource res;
- int ret = 0;
+ void __iomem *base;
np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
if (!np)
return 0;
- pr_info("Initializing 98DX3236 Resume\n");
-
- if (of_address_to_resource(np, 0, &res)) {
- pr_err("unable to get resource\n");
- ret = -ENOENT;
- goto out;
- }
-
- if (!request_mem_region(res.start, resource_size(&res),
- np->full_name)) {
- pr_err("unable to request region\n");
- ret = -EBUSY;
- goto out;
- }
-
- mv98dx3236_resume_base = ioremap(res.start,
resource_size(&res));
- if (!mv98dx3236_resume_base) {
+ base = of_io_request_and_map(np, 0, of_node_full_name(np));
+ if (IS_ERR(base)) {
pr_err("unable to map registers\n");
- release_mem_region(res.start, resource_size(&res));
- ret = -ENOMEM;
- goto out;
+ of_node_put(np);
+ return PTR_ERR(mv98dx3236_resume_base);
}
-out:
+ mv98dx3236_resume_base = base;
of_node_put(np);
- return ret;
+ return 0;
}
early_initcall(mv98dx3236_resume_init);
diff --git a/drivers/clk/mvebu/Makefile b/drivers/clk/mvebu/Makefile
index 6a3681e3d6db..d9ae97fb43c4 100644
--- a/drivers/clk/mvebu/Makefile
+++ b/drivers/clk/mvebu/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_ARMADA_39X_CLK) += armada-39x.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-xtal.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-tbg.o
obj-$(CONFIG_ARMADA_37XX_CLK) += armada-37xx-periph.o
-obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o mv98dx3236-corediv.o
+obj-$(CONFIG_ARMADA_XP_CLK) += armada-xp.o
obj-$(CONFIG_ARMADA_AP806_SYSCON) += ap806-system-controller.o
obj-$(CONFIG_ARMADA_CP110_SYSCON) += cp110-system-controller.o
obj-$(CONFIG_DOVE_CLK) += dove.o dove-divider.o
diff --git a/drivers/clk/mvebu/clk-corediv.c
b/drivers/clk/mvebu/clk-corediv.c
index d1e5863d3375..8491979f4096 100644
--- a/drivers/clk/mvebu/clk-corediv.c
+++ b/drivers/clk/mvebu/clk-corediv.c
@@ -71,6 +71,10 @@ static const struct clk_corediv_desc
mvebu_corediv_desc[] = {
{ .mask = 0x3f, .offset = 8, .fieldbit = 1 }, /* NAND clock */
};
+static const struct clk_corediv_desc mv98dx3236_corediv_desc[] = {
+ { .mask = 0x0f, .offset = 6, .fieldbit = 26 }, /* NAND clock */
+};
+
#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
static int clk_corediv_is_enabled(struct clk_hw *hwclk)
@@ -232,6 +236,18 @@ static const struct clk_corediv_soc_desc
armada375_corediv_soc = {
.ratio_offset = 0x4,
};
+static const struct clk_corediv_soc_desc mv98dx3236_corediv_soc = {
+ .descs = mv98dx3236_corediv_desc,
+ .ndescs = ARRAY_SIZE(mv98dx3236_corediv_desc),
+ .ops = {
+ .recalc_rate = clk_corediv_recalc_rate,
+ .round_rate = clk_corediv_round_rate,
+ .set_rate = clk_corediv_set_rate,
+ },
+ .ratio_reload = BIT(10),
+ .ratio_offset = 0x8,
+};
+
static void __init
mvebu_corediv_clk_init(struct device_node *node,
const struct clk_corediv_soc_desc *soc_desc)
@@ -313,3 +329,10 @@ static void __init
armada380_corediv_clk_init(struct device_node *node)
}
CLK_OF_DECLARE(armada380_corediv_clk,
"marvell,armada-380-corediv-clock",
armada380_corediv_clk_init);
+
+static void __init mv98dx3236_corediv_clk_init(struct device_node
*node)
+{
+ return mvebu_corediv_clk_init(node, &mv98dx3236_corediv_soc);
+}
+CLK_OF_DECLARE(mv98dx3236_corediv_clk,
"marvell,mv98dx3236-corediv-clock",
+ mv98dx3236_corediv_clk_init);
diff --git a/drivers/clk/mvebu/clk-cpu.c b/drivers/clk/mvebu/clk-cpu.c
index 29f295e7a36b..3b8f0e14fa01 100644
--- a/drivers/clk/mvebu/clk-cpu.c
+++ b/drivers/clk/mvebu/clk-cpu.c
@@ -254,7 +254,7 @@ static void __init of_cpu_clk_setup(struct
device_node *node)
}
CLK_OF_DECLARE(armada_xp_cpu_clock, "marvell,armada-xp-cpu-clock",
- of_cpu_clk_setup);
+ of_cpu_clk_setup);
/* Define the clock and operations for the mv98dx3236 - it cannot
* perform
* any operations.
diff --git a/drivers/clk/mvebu/mv98dx3236-corediv.c
b/drivers/clk/mvebu/mv98dx3236-corediv.c
deleted file mode 100644
index 3060764a8e5d..000000000000
--- a/drivers/clk/mvebu/mv98dx3236-corediv.c
+++ /dev/null
@@ -1,207 +0,0 @@
-/*
- * MV98DX3236 Core divider clock
- *
- * Copyright (C) 2015 Allied Telesis Labs
- *
- * Based on armada-xp-corediv.c
- * Copyright (C) 2015 Marvell
- *
- * John Thompson <john.thompson@alliedtelesis.co.nz>
- *
- * This file is licensed under the terms of the GNU General Public
- * License version 2. This program is licensed "as is" without any
- * warranty of any kind, whether express or implied.
- */
-#include <linux/kernel.h>
-#include <linux/clk-provider.h>
-#include <linux/of_address.h>
-#include <linux/slab.h>
-#include <linux/delay.h>
-#include "common.h"
-
-#define CORE_CLK_DIV_RATIO_MASK 0xff
-
-#define CLK_DIV_RATIO_NAND_MASK 0x0f
-#define CLK_DIV_RATIO_NAND_OFFSET 6
-#define CLK_DIV_RATIO_NAND_FORCE_RELOAD_BIT 26
-
-#define RATIO_RELOAD_BIT BIT(10)
-#define RATIO_REG_OFFSET 0x08
-
-/*
- * This structure represents one core divider clock for the clock
- * framework, and is dynamically allocated for each core divider clock
- * existing in the current SoC.
- */
-struct clk_corediv {
- struct clk_hw hw;
- void __iomem *reg;
- spinlock_t lock;
-};
-
-static struct clk_onecell_data clk_data;
-
-
-#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
-
-static int mv98dx3236_corediv_is_enabled(struct clk_hw *hwclk)
-{
- /* Core divider is always active */
- return 1;
-}
-
-static int mv98dx3236_corediv_enable(struct clk_hw *hwclk)
-{
- /* always succeeds */
- return 0;
-}
-
-static void mv98dx3236_corediv_disable(struct clk_hw *hwclk)
-{
- /* can't be disabled so is left alone */
-}
-
-static unsigned long mv98dx3236_corediv_recalc_rate(struct clk_hw
*hwclk,
- unsigned long parent_rate)
-{
- struct clk_corediv *corediv = to_corediv_clk(hwclk);
- u32 reg, div;
-
- reg = readl(corediv->reg + RATIO_REG_OFFSET);
- div = (reg >> CLK_DIV_RATIO_NAND_OFFSET) &
CLK_DIV_RATIO_NAND_MASK;
- return parent_rate / div;
-}
-
-static long mv98dx3236_corediv_round_rate(struct clk_hw *hwclk,
- unsigned long rate, unsigned long
*parent_rate)
-{
- /* Valid ratio are 1:4, 1:5, 1:6 and 1:8 */
- u32 div;
-
- div = *parent_rate / rate;
- if (div < 4)
- div = 4;
- else if (div > 6)
- div = 8;
-
- return *parent_rate / div;
-}
-
-static int mv98dx3236_corediv_set_rate(struct clk_hw *hwclk, unsigned
long rate,
- unsigned long parent_rate)
-{
- struct clk_corediv *corediv = to_corediv_clk(hwclk);
- unsigned long flags = 0;
- u32 reg, div;
-
- div = parent_rate / rate;
-
- spin_lock_irqsave(&corediv->lock, flags);
-
- /* Write new divider to the divider ratio register */
- reg = readl(corediv->reg + RATIO_REG_OFFSET);
- reg &= ~(CLK_DIV_RATIO_NAND_MASK << CLK_DIV_RATIO_NAND_OFFSET);
- reg |= (div & CLK_DIV_RATIO_NAND_MASK) <<
CLK_DIV_RATIO_NAND_OFFSET;
- writel(reg, corediv->reg + RATIO_REG_OFFSET);
-
- /* Set reload-force for this clock */
- reg = readl(corediv->reg) |
BIT(CLK_DIV_RATIO_NAND_FORCE_RELOAD_BIT);
- writel(reg, corediv->reg);
-
- /* Now trigger the clock update */
- reg = readl(corediv->reg + RATIO_REG_OFFSET) | RATIO_RELOAD_BIT;
- writel(reg, corediv->reg + RATIO_REG_OFFSET);
-
- /*
- * Wait for clocks to settle down, and then clear all the
- * ratios request and the reload request.
- */
- udelay(1000);
- reg &= ~(CORE_CLK_DIV_RATIO_MASK | RATIO_RELOAD_BIT);
- writel(reg, corediv->reg + RATIO_REG_OFFSET);
- udelay(1000);
-
- spin_unlock_irqrestore(&corediv->lock, flags);
-
- return 0;
-}
-
-static const struct clk_ops ops = {
- .enable = mv98dx3236_corediv_enable,
- .disable = mv98dx3236_corediv_disable,
- .is_enabled = mv98dx3236_corediv_is_enabled,
- .recalc_rate = mv98dx3236_corediv_recalc_rate,
- .round_rate = mv98dx3236_corediv_round_rate,
- .set_rate = mv98dx3236_corediv_set_rate,
-};
-
-static void __init mv98dx3236_corediv_clk_init(struct device_node
*node)
-{
- struct clk_init_data init;
- struct clk_corediv *corediv;
- struct clk **clks;
- void __iomem *base;
- const __be32 *off;
- const char *parent_name;
- const char *clk_name;
- int len;
- struct device_node *dfx_node;
-
- dfx_node = of_parse_phandle(node, "base", 0);
- if (WARN_ON(!dfx_node))
- return;
-
- off = of_get_property(node, "reg", &len);
- if (WARN_ON(!off))
- return;
-
- base = of_iomap(dfx_node, 0);
- if (WARN_ON(!base))
- return;
-
- of_node_put(dfx_node);
-
- parent_name = of_clk_get_parent_name(node, 0);
-
- clk_data.clk_num = 1;
-
- /* clks holds the clock array */
- clks = kcalloc(clk_data.clk_num, sizeof(struct clk *),
- GFP_KERNEL);
- if (WARN_ON(!clks))
- goto err_unmap;
- /* corediv holds the clock specific array */
- corediv = kcalloc(clk_data.clk_num, sizeof(struct clk_corediv),
- GFP_KERNEL);
- if (WARN_ON(!corediv))
- goto err_free_clks;
-
- spin_lock_init(&corediv->lock);
-
- of_property_read_string_index(node, "clock-output-names",
- 0, &clk_name);
-
- init.num_parents = 1;
- init.parent_names = &parent_name;
- init.name = clk_name;
- init.ops = &ops;
- init.flags = 0;
-
- corediv[0].reg = (void *)((int)base + be32_to_cpu(*off));
- corediv[0].hw.init = &init;
-
- clks[0] = clk_register(NULL, &corediv[0].hw);
- WARN_ON(IS_ERR(clks[0]));
-
- clk_data.clks = clks;
- of_clk_add_provider(node, of_clk_src_onecell_get, &clk_data);
- return;
-
-err_free_clks:
- kfree(clks);
-err_unmap:
- iounmap(base);
-}
-
-CLK_OF_DECLARE(mv98dx3236_corediv_clk,
"marvell,mv98dx3236-corediv-clock",
- mv98dx3236_corediv_clk_init);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC
2017-01-06 4:14 ` Chris Packham
@ 2017-01-06 4:14 ` Chris Packham
2017-01-09 18:39 ` Rob Herring
2017-01-06 4:14 ` [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
` (3 subsequent siblings)
4 siblings, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
The clock gating options are a subset of those on the Armada XP.
The core clock divider is different to the Armada XP also.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Update devicetree binding documentation for new compatible string
Changes in v3:
- Add 98dx3236 support to mvebu/clk-corediv.c rather than creating a new
driver.
- Document mv98dx3236-corediv-clock binding
.../bindings/clock/mvebu-corediv-clock.txt | 1 +
.../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
drivers/clk/mvebu/armada-xp.c | 42 ++++++++++++++++++++++
drivers/clk/mvebu/clk-corediv.c | 23 ++++++++++++
drivers/clk/mvebu/clk-cpu.c | 31 ++++++++++++++--
5 files changed, 96 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
index 520562a7dc2a..c7b4e3a6b2c6 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-corediv-clock.txt
@@ -7,6 +7,7 @@ Required properties:
- compatible : must be "marvell,armada-370-corediv-clock",
"marvell,armada-375-corediv-clock",
"marvell,armada-380-corediv-clock",
+ "marvell,mv98dx3236-corediv-clock",
- reg : must be the register address of Core Divider control register
- #clock-cells : from common clock binding; shall be set to 1
diff --git a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
index 99c214660bdc..7f28506eaee7 100644
--- a/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
+++ b/Documentation/devicetree/bindings/clock/mvebu-cpu-clock.txt
@@ -3,6 +3,7 @@ Device Tree Clock bindings for cpu clock of Marvell EBU platforms
Required properties:
- compatible : shall be one of the following:
"marvell,armada-xp-cpu-clock" - cpu clocks for Armada XP
+ "marvell,mv98dx3236-cpu-clock" - cpu clocks for 98DX3236 SoC
- reg : Address and length of the clock complex register set, followed
by address and length of the PMU DFS registers
- #clock-cells : should be set to 1.
diff --git a/drivers/clk/mvebu/armada-xp.c b/drivers/clk/mvebu/armada-xp.c
index b3094315a3c0..0413bf8284e0 100644
--- a/drivers/clk/mvebu/armada-xp.c
+++ b/drivers/clk/mvebu/armada-xp.c
@@ -52,6 +52,12 @@ static u32 __init axp_get_tclk_freq(void __iomem *sar)
return 250000000;
}
+/* MV98DX3236 TCLK frequency is fixed to 200MHz */
+static u32 __init mv98dx3236_get_tclk_freq(void __iomem *sar)
+{
+ return 200000000;
+}
+
static const u32 axp_cpu_freqs[] __initconst = {
1000000000,
1066000000,
@@ -89,6 +95,12 @@ static u32 __init axp_get_cpu_freq(void __iomem *sar)
return cpu_freq;
}
+/* MV98DX3236 CLK frequency is fixed to 800MHz */
+static u32 __init mv98dx3236_get_cpu_freq(void __iomem *sar)
+{
+ return 800000000;
+}
+
static const int axp_nbclk_ratios[32][2] __initconst = {
{0, 1}, {1, 2}, {2, 2}, {2, 2},
{1, 2}, {1, 2}, {1, 1}, {2, 3},
@@ -158,6 +170,14 @@ static const struct coreclk_soc_desc axp_coreclks = {
.num_ratios = ARRAY_SIZE(axp_coreclk_ratios),
};
+static const struct coreclk_soc_desc mv98dx3236_coreclks = {
+ .get_tclk_freq = mv98dx3236_get_tclk_freq,
+ .get_cpu_freq = mv98dx3236_get_cpu_freq,
+ .get_clk_ratio = NULL,
+ .ratios = NULL,
+ .num_ratios = 0,
+};
+
/*
* Clock Gating Control
*/
@@ -195,6 +215,15 @@ static const struct clk_gating_soc_desc axp_gating_desc[] __initconst = {
{ }
};
+static const struct clk_gating_soc_desc mv98dx3236_gating_desc[] __initconst = {
+ { "ge1", NULL, 3, 0 },
+ { "ge0", NULL, 4, 0 },
+ { "pex00", NULL, 5, 0 },
+ { "sdio", NULL, 17, 0 },
+ { "xor0", NULL, 22, 0 },
+ { }
+};
+
static void __init axp_clk_init(struct device_node *np)
{
struct device_node *cgnp =
@@ -206,3 +235,16 @@ static void __init axp_clk_init(struct device_node *np)
mvebu_clk_gating_setup(cgnp, axp_gating_desc);
}
CLK_OF_DECLARE(axp_clk, "marvell,armada-xp-core-clock", axp_clk_init);
+
+static void __init mv98dx3236_clk_init(struct device_node *np)
+{
+ struct device_node *cgnp =
+ of_find_compatible_node(NULL, NULL, "marvell,armada-xp-gating-clock");
+
+ mvebu_coreclk_setup(np, &mv98dx3236_coreclks);
+
+ if (cgnp)
+ mvebu_clk_gating_setup(cgnp, mv98dx3236_gating_desc);
+}
+CLK_OF_DECLARE(mv98dx3236_clk, "marvell,mv98dx3236-core-clock",
+ mv98dx3236_clk_init);
diff --git a/drivers/clk/mvebu/clk-corediv.c b/drivers/clk/mvebu/clk-corediv.c
index d1e5863d3375..8491979f4096 100644
--- a/drivers/clk/mvebu/clk-corediv.c
+++ b/drivers/clk/mvebu/clk-corediv.c
@@ -71,6 +71,10 @@ static const struct clk_corediv_desc mvebu_corediv_desc[] = {
{ .mask = 0x3f, .offset = 8, .fieldbit = 1 }, /* NAND clock */
};
+static const struct clk_corediv_desc mv98dx3236_corediv_desc[] = {
+ { .mask = 0x0f, .offset = 6, .fieldbit = 26 }, /* NAND clock */
+};
+
#define to_corediv_clk(p) container_of(p, struct clk_corediv, hw)
static int clk_corediv_is_enabled(struct clk_hw *hwclk)
@@ -232,6 +236,18 @@ static const struct clk_corediv_soc_desc armada375_corediv_soc = {
.ratio_offset = 0x4,
};
+static const struct clk_corediv_soc_desc mv98dx3236_corediv_soc = {
+ .descs = mv98dx3236_corediv_desc,
+ .ndescs = ARRAY_SIZE(mv98dx3236_corediv_desc),
+ .ops = {
+ .recalc_rate = clk_corediv_recalc_rate,
+ .round_rate = clk_corediv_round_rate,
+ .set_rate = clk_corediv_set_rate,
+ },
+ .ratio_reload = BIT(10),
+ .ratio_offset = 0x8,
+};
+
static void __init
mvebu_corediv_clk_init(struct device_node *node,
const struct clk_corediv_soc_desc *soc_desc)
@@ -313,3 +329,10 @@ static void __init armada380_corediv_clk_init(struct device_node *node)
}
CLK_OF_DECLARE(armada380_corediv_clk, "marvell,armada-380-corediv-clock",
armada380_corediv_clk_init);
+
+static void __init mv98dx3236_corediv_clk_init(struct device_node *node)
+{
+ return mvebu_corediv_clk_init(node, &mv98dx3236_corediv_soc);
+}
+CLK_OF_DECLARE(mv98dx3236_corediv_clk, "marvell,mv98dx3236-corediv-clock",
+ mv98dx3236_corediv_clk_init);
diff --git a/drivers/clk/mvebu/clk-cpu.c b/drivers/clk/mvebu/clk-cpu.c
index 5837eb8a212f..3b8f0e14fa01 100644
--- a/drivers/clk/mvebu/clk-cpu.c
+++ b/drivers/clk/mvebu/clk-cpu.c
@@ -165,7 +165,9 @@ static const struct clk_ops cpu_ops = {
.set_rate = clk_cpu_set_rate,
};
-static void __init of_cpu_clk_setup(struct device_node *node)
+/* Add parameter to allow this to support different clock operations. */
+static void __init _of_cpu_clk_setup(struct device_node *node,
+ const struct clk_ops *cpu_clk_ops)
{
struct cpu_clk *cpuclk;
void __iomem *clock_complex_base = of_iomap(node, 0);
@@ -218,7 +220,7 @@ static void __init of_cpu_clk_setup(struct device_node *node)
cpuclk[cpu].hw.init = &init;
init.name = cpuclk[cpu].clk_name;
- init.ops = &cpu_ops;
+ init.ops = cpu_clk_ops;
init.flags = 0;
init.parent_names = &cpuclk[cpu].parent_name;
init.num_parents = 1;
@@ -243,5 +245,30 @@ static void __init of_cpu_clk_setup(struct device_node *node)
iounmap(clock_complex_base);
}
+/* Use this function to call the generic setup with the correct
+ * clock operation
+ */
+static void __init of_cpu_clk_setup(struct device_node *node)
+{
+ _of_cpu_clk_setup(node, &cpu_ops);
+}
+
CLK_OF_DECLARE(armada_xp_cpu_clock, "marvell,armada-xp-cpu-clock",
of_cpu_clk_setup);
+
+/* Define the clock and operations for the mv98dx3236 - it cannot perform
+ * any operations.
+ */
+static const struct clk_ops mv98dx3236_cpu_ops = {
+ .recalc_rate = NULL,
+ .round_rate = NULL,
+ .set_rate = NULL,
+};
+
+static void __init of_mv98dx3236_cpu_clk_setup(struct device_node *node)
+{
+ _of_cpu_clk_setup(node, &mv98dx3236_cpu_ops);
+}
+
+CLK_OF_DECLARE(mv98dx3236_cpu_clock, "marvell,mv98dx3236-cpu-clock",
+ of_mv98dx3236_cpu_clk_setup);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC
2017-01-06 4:14 ` [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
@ 2017-01-09 18:39 ` Rob Herring
0 siblings, 0 replies; 43+ messages in thread
From: Rob Herring @ 2017-01-09 18:39 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jan 06, 2017 at 05:14:58PM +1300, Chris Packham wrote:
> The 98DX3236, 98DX3336, 98DX4521 and variants have a different TCLK from
> the Armada XP (200MHz vs 250MHz). The CPU core clock is fixed at 800MHz.
>
> The clock gating options are a subset of those on the Armada XP.
>
> The core clock divider is different to the Armada XP also.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - Update devicetree binding documentation for new compatible string
>
> Changes in v3:
> - Add 98dx3236 support to mvebu/clk-corediv.c rather than creating a new
> driver.
> - Document mv98dx3236-corediv-clock binding
>
> .../bindings/clock/mvebu-corediv-clock.txt | 1 +
> .../devicetree/bindings/clock/mvebu-cpu-clock.txt | 1 +
Acked-by: Rob Herring <robh@kernel.org>
> drivers/clk/mvebu/armada-xp.c | 42 ++++++++++++++++++++++
> drivers/clk/mvebu/clk-corediv.c | 23 ++++++++++++
> drivers/clk/mvebu/clk-cpu.c | 31 ++++++++++++++--
> 5 files changed, 96 insertions(+), 2 deletions(-)
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-06 4:14 ` Chris Packham
2017-01-06 4:14 ` [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
@ 2017-01-06 4:14 ` Chris Packham
2017-01-06 6:36 ` Stephen Boyd
2017-01-09 18:40 ` Rob Herring
2017-01-06 4:15 ` [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC Chris Packham
` (2 subsequent siblings)
4 siblings, 2 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-06 4:14 UTC (permalink / raw)
To: linux-arm-kernel
Compared to the armada-xp the 98DX3336 uses different registers to set
the boot address for the secondary CPU so a new enable-method is needed.
This will only work if the machine definition doesn't define an overall
smp_ops because there is not currently a way of overriding this from the
device tree if it is set in the machine definition.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Document new enable-method value
- Correct some references from 98DX4521 to 98DX3236
Changes in v3:
- Simplify mv98dx3236_resume_init by using of_io_request_and_map()
Documentation/devicetree/bindings/arm/cpus.txt | 1 +
.../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++++++++
arch/arm/mach-mvebu/Makefile | 1 +
arch/arm/mach-mvebu/common.h | 1 +
arch/arm/mach-mvebu/platsmp.c | 43 ++++++++++++++++++
arch/arm/mach-mvebu/pmsu-98dx3236.c | 52 ++++++++++++++++++++++
6 files changed, 116 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt
index a1bcfeed5f24..3c2fd72d0bf9 100644
--- a/Documentation/devicetree/bindings/arm/cpus.txt
+++ b/Documentation/devicetree/bindings/arm/cpus.txt
@@ -202,6 +202,7 @@ nodes to be present and contain the properties described below.
"marvell,armada-380-smp"
"marvell,armada-390-smp"
"marvell,armada-xp-smp"
+ "marvell,98dx3236-smp"
"mediatek,mt6589-smp"
"mediatek,mt81xx-tz-smp"
"qcom,gcc-msm8660"
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
new file mode 100644
index 000000000000..8082ba872edd
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
@@ -0,0 +1,18 @@
+Resume Control
+--------------
+Available on Marvell SOCs: 98DX3336 and 98DX4251
+
+Required properties:
+
+- compatible: must be "marvell,98dx3336-resume-ctrl"
+
+- reg: Should contain resume control registers location and length
+
+Example:
+
+resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+};
+
+
diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
index 6c6497e80a7b..2a2dd8324fb8 100644
--- a/arch/arm/mach-mvebu/Makefile
+++ b/arch/arm/mach-mvebu/Makefile
@@ -7,6 +7,7 @@ obj-$(CONFIG_MACH_MVEBU_ANY) += system-controller.o mvebu-soc-id.o
ifeq ($(CONFIG_MACH_MVEBU_V7),y)
obj-y += cpu-reset.o board-v7.o coherency.o coherency_ll.o pmsu.o pmsu_ll.o
+obj-y += pmsu-98dx3236.o
obj-$(CONFIG_PM) += pm.o pm-board.o
obj-$(CONFIG_SMP) += platsmp.o headsmp.o platsmp-a9.o headsmp-a9.o
diff --git a/arch/arm/mach-mvebu/common.h b/arch/arm/mach-mvebu/common.h
index 6b775492cfad..099dabf23461 100644
--- a/arch/arm/mach-mvebu/common.h
+++ b/arch/arm/mach-mvebu/common.h
@@ -27,4 +27,5 @@ void __iomem *mvebu_get_scu_base(void);
int mvebu_pm_suspend_init(void (*board_pm_enter)(void __iomem *sdram_reg,
u32 srcmd));
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr);
#endif
diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
index 46c742d3bd41..3c9ab9a008ad 100644
--- a/arch/arm/mach-mvebu/platsmp.c
+++ b/arch/arm/mach-mvebu/platsmp.c
@@ -182,5 +182,48 @@ const struct smp_operations armada_xp_smp_ops __initconst = {
#endif
};
+static int mv98dx3236_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ int ret, hw_cpu;
+
+ pr_info("Booting CPU %d\n", cpu);
+
+ hw_cpu = cpu_logical_map(cpu);
+ set_secondary_cpu_clock(hw_cpu);
+ mv98dx3236_resume_set_cpu_boot_addr(hw_cpu,
+ armada_xp_secondary_startup);
+
+ /*
+ * This is needed to wake up CPUs in the offline state after
+ * using CPU hotplug.
+ */
+ arch_send_wakeup_ipi_mask(cpumask_of(cpu));
+
+ /*
+ * This is needed to take secondary CPUs out of reset on the
+ * initial boot.
+ */
+ ret = mvebu_cpu_reset_deassert(hw_cpu);
+ if (ret) {
+ pr_warn("unable to boot CPU: %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+struct smp_operations mv98dx3236_smp_ops __initdata = {
+ .smp_init_cpus = armada_xp_smp_init_cpus,
+ .smp_prepare_cpus = armada_xp_smp_prepare_cpus,
+ .smp_boot_secondary = mv98dx3236_boot_secondary,
+ .smp_secondary_init = armada_xp_secondary_init,
+#ifdef CONFIG_HOTPLUG_CPU
+ .cpu_die = armada_xp_cpu_die,
+ .cpu_kill = armada_xp_cpu_kill,
+#endif
+};
+
CPU_METHOD_OF_DECLARE(armada_xp_smp, "marvell,armada-xp-smp",
&armada_xp_smp_ops);
+CPU_METHOD_OF_DECLARE(mv98dx3236_smp, "marvell,98dx3236-smp",
+ &mv98dx3236_smp_ops);
diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c b/arch/arm/mach-mvebu/pmsu-98dx3236.c
new file mode 100644
index 000000000000..1052674dd439
--- /dev/null
+++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
@@ -0,0 +1,52 @@
+/**
+ * CPU resume support for 98DX3236 internal CPU (a.k.a. MSYS).
+ */
+
+#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/of_address.h>
+#include <linux/io.h>
+#include "common.h"
+
+static void __iomem *mv98dx3236_resume_base;
+#define MV98DX3236_CPU_RESUME_CTRL_OFFSET 0x08
+#define MV98DX3236_CPU_RESUME_ADDR_OFFSET 0x04
+
+static const struct of_device_id of_mv98dx3236_resume_table[] = {
+ {.compatible = "marvell,98dx3336-resume-ctrl",},
+ { /* end of list */ },
+};
+
+void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
+{
+ WARN_ON(hw_cpu != 1);
+
+ writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
+ writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
+ MV98DX3236_CPU_RESUME_ADDR_OFFSET);
+}
+
+static int __init mv98dx3236_resume_init(void)
+{
+ struct device_node *np;
+ void __iomem *base;
+
+ np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
+ if (!np)
+ return 0;
+
+ base = of_io_request_and_map(np, 0, of_node_full_name(np));
+ if (IS_ERR(base)) {
+ pr_err("unable to map registers\n");
+ of_node_put(np);
+ return PTR_ERR(mv98dx3236_resume_base);
+ }
+
+ mv98dx3236_resume_base = base;
+ of_node_put(np);
+ return 0;
+}
+
+early_initcall(mv98dx3236_resume_init);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-06 4:14 ` [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
@ 2017-01-06 6:36 ` Stephen Boyd
2017-01-06 8:41 ` Chris Packham
2017-01-09 18:40 ` Rob Herring
1 sibling, 1 reply; 43+ messages in thread
From: Stephen Boyd @ 2017-01-06 6:36 UTC (permalink / raw)
To: linux-arm-kernel
On 01/06, Chris Packham wrote:
> diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
> index 46c742d3bd41..3c9ab9a008ad 100644
> --- a/arch/arm/mach-mvebu/platsmp.c
> +++ b/arch/arm/mach-mvebu/platsmp.c
> @@ -182,5 +182,48 @@ const struct smp_operations armada_xp_smp_ops __initconst = {
> #endif
> };
>
> +static int mv98dx3236_boot_secondary(unsigned int cpu, struct task_struct *idle)
> +{
> + int ret, hw_cpu;
> +
> + pr_info("Booting CPU %d\n", cpu);
Doesn't the core already print something when bringing up CPUs?
This message seems redundant.
> +
> + hw_cpu = cpu_logical_map(cpu);
> + set_secondary_cpu_clock(hw_cpu);
> + mv98dx3236_resume_set_cpu_boot_addr(hw_cpu,
> + armada_xp_secondary_startup);
> +
> + /*
> + * This is needed to wake up CPUs in the offline state after
> + * using CPU hotplug.
> + */
> + arch_send_wakeup_ipi_mask(cpumask_of(cpu));
> +
> + /*
> + * This is needed to take secondary CPUs out of reset on the
> + * initial boot.
> + */
> + ret = mvebu_cpu_reset_deassert(hw_cpu);
> + if (ret) {
> + pr_warn("unable to boot CPU: %d\n", ret);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +struct smp_operations mv98dx3236_smp_ops __initdata = {
static const __initconst?
> + .smp_init_cpus = armada_xp_smp_init_cpus,
> + .smp_prepare_cpus = armada_xp_smp_prepare_cpus,
> + .smp_boot_secondary = mv98dx3236_boot_secondary,
> + .smp_secondary_init = armada_xp_secondary_init,
> +#ifdef CONFIG_HOTPLUG_CPU
> + .cpu_die = armada_xp_cpu_die,
> + .cpu_kill = armada_xp_cpu_kill,
> +#endif
> +};
> +
> CPU_METHOD_OF_DECLARE(armada_xp_smp, "marvell,armada-xp-smp",
> &armada_xp_smp_ops);
> +CPU_METHOD_OF_DECLARE(mv98dx3236_smp, "marvell,98dx3236-smp",
> + &mv98dx3236_smp_ops);
> diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c b/arch/arm/mach-mvebu/pmsu-98dx3236.c
> new file mode 100644
> index 000000000000..1052674dd439
> --- /dev/null
> +++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
> @@ -0,0 +1,52 @@
> +/**
> + * CPU resume support for 98DX3236 internal CPU (a.k.a. MSYS).
> + */
> +
> +#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
> +
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/of_address.h>
> +#include <linux/io.h>
> +#include "common.h"
> +
> +static void __iomem *mv98dx3236_resume_base;
> +#define MV98DX3236_CPU_RESUME_CTRL_OFFSET 0x08
> +#define MV98DX3236_CPU_RESUME_ADDR_OFFSET 0x04
> +
> +static const struct of_device_id of_mv98dx3236_resume_table[] = {
> + {.compatible = "marvell,98dx3336-resume-ctrl",},
> + { /* end of list */ },
> +};
> +
> +void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
> +{
> + WARN_ON(hw_cpu != 1);
> +
> + writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
> + writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
> + MV98DX3236_CPU_RESUME_ADDR_OFFSET);
> +}
> +
> +static int __init mv98dx3236_resume_init(void)
> +{
> + struct device_node *np;
> + void __iomem *base;
> +
> + np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
> + if (!np)
> + return 0;
Is there any reason we can't just look for this node from the
smp_ops and map it if it isn't mapped yet? Seems simpler than a
whole new file and initcall.
> +
> + base = of_io_request_and_map(np, 0, of_node_full_name(np));
> + if (IS_ERR(base)) {
> + pr_err("unable to map registers\n");
Doesn't of_io_request_and_map() spit out an error on failure
already?
> + of_node_put(np);
This could be done before the if statement and then the duplicate
statement deleted.
> + return PTR_ERR(mv98dx3236_resume_base);
Should be PTR_ERR(base)?
> + }
> +
> + mv98dx3236_resume_base = base;
> + of_node_put(np);
> + return 0;
> +}
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-06 6:36 ` Stephen Boyd
@ 2017-01-06 8:41 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-06 8:41 UTC (permalink / raw)
To: linux-arm-kernel
On 06/01/17 19:44, Stephen Boyd wrote:
> On 01/06, Chris Packham wrote:
>> diff --git a/arch/arm/mach-mvebu/platsmp.c b/arch/arm/mach-mvebu/platsmp.c
>> index 46c742d3bd41..3c9ab9a008ad 100644
>> --- a/arch/arm/mach-mvebu/platsmp.c
>> +++ b/arch/arm/mach-mvebu/platsmp.c
>> @@ -182,5 +182,48 @@ const struct smp_operations armada_xp_smp_ops __initconst = {
>> #endif
>> };
>>
>> +static int mv98dx3236_boot_secondary(unsigned int cpu, struct task_struct *idle)
>> +{
>> + int ret, hw_cpu;
>> +
>> + pr_info("Booting CPU %d\n", cpu);
>
> Doesn't the core already print something when bringing up CPUs?
> This message seems redundant.
>
Copied from armada_xp_boot_secondary but that's no reason to keep it.
Will remove in v4.
>> +
>> + hw_cpu = cpu_logical_map(cpu);
>> + set_secondary_cpu_clock(hw_cpu);
>> + mv98dx3236_resume_set_cpu_boot_addr(hw_cpu,
>> + armada_xp_secondary_startup);
>> +
>> + /*
>> + * This is needed to wake up CPUs in the offline state after
>> + * using CPU hotplug.
>> + */
>> + arch_send_wakeup_ipi_mask(cpumask_of(cpu));
>> +
>> + /*
>> + * This is needed to take secondary CPUs out of reset on the
>> + * initial boot.
>> + */
>> + ret = mvebu_cpu_reset_deassert(hw_cpu);
>> + if (ret) {
>> + pr_warn("unable to boot CPU: %d\n", ret);
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +struct smp_operations mv98dx3236_smp_ops __initdata = {
>
> static const __initconst?
>
Will do.
>> + .smp_init_cpus = armada_xp_smp_init_cpus,
>> + .smp_prepare_cpus = armada_xp_smp_prepare_cpus,
>> + .smp_boot_secondary = mv98dx3236_boot_secondary,
>> + .smp_secondary_init = armada_xp_secondary_init,
>> +#ifdef CONFIG_HOTPLUG_CPU
>> + .cpu_die = armada_xp_cpu_die,
>> + .cpu_kill = armada_xp_cpu_kill,
>> +#endif
>> +};
>> +
>> CPU_METHOD_OF_DECLARE(armada_xp_smp, "marvell,armada-xp-smp",
>> &armada_xp_smp_ops);
>> +CPU_METHOD_OF_DECLARE(mv98dx3236_smp, "marvell,98dx3236-smp",
>> + &mv98dx3236_smp_ops);
>> diff --git a/arch/arm/mach-mvebu/pmsu-98dx3236.c b/arch/arm/mach-mvebu/pmsu-98dx3236.c
>> new file mode 100644
>> index 000000000000..1052674dd439
>> --- /dev/null
>> +++ b/arch/arm/mach-mvebu/pmsu-98dx3236.c
>> @@ -0,0 +1,52 @@
>> +/**
>> + * CPU resume support for 98DX3236 internal CPU (a.k.a. MSYS).
>> + */
>> +
>> +#define pr_fmt(fmt) "mv98dx3236-resume: " fmt
>> +
>> +#include <linux/kernel.h>
>> +#include <linux/init.h>
>> +#include <linux/of_address.h>
>> +#include <linux/io.h>
>> +#include "common.h"
>> +
>> +static void __iomem *mv98dx3236_resume_base;
>> +#define MV98DX3236_CPU_RESUME_CTRL_OFFSET 0x08
>> +#define MV98DX3236_CPU_RESUME_ADDR_OFFSET 0x04
>> +
>> +static const struct of_device_id of_mv98dx3236_resume_table[] = {
>> + {.compatible = "marvell,98dx3336-resume-ctrl",},
>> + { /* end of list */ },
>> +};
>> +
>> +void mv98dx3236_resume_set_cpu_boot_addr(int hw_cpu, void *boot_addr)
>> +{
>> + WARN_ON(hw_cpu != 1);
>> +
>> + writel(0, mv98dx3236_resume_base + MV98DX3236_CPU_RESUME_CTRL_OFFSET);
>> + writel(virt_to_phys(boot_addr), mv98dx3236_resume_base +
>> + MV98DX3236_CPU_RESUME_ADDR_OFFSET);
>> +}
>> +
>> +static int __init mv98dx3236_resume_init(void)
>> +{
>> + struct device_node *np;
>> + void __iomem *base;
>> +
>> + np = of_find_matching_node(NULL, of_mv98dx3236_resume_table);
>> + if (!np)
>> + return 0;
>
> Is there any reason we can't just look for this node from the
> smp_ops and map it if it isn't mapped yet? Seems simpler than a
> whole new file and initcall.
>
That's at least 2 votes for rolling it into platsmp.c. The amount of
code has been significantly reduced so I think I will do it for v4.
>> +
>> + base = of_io_request_and_map(np, 0, of_node_full_name(np));
>> + if (IS_ERR(base)) {
>> + pr_err("unable to map registers\n");
>
> Doesn't of_io_request_and_map() spit out an error on failure
> already?
>
Not that I can see. But as has been previously mentioned a CPU failing
to come online is reasonably obvious already.
>> + of_node_put(np);
>
> This could be done before the if statement and then the duplicate
> statement deleted.
>
Will do.
>> + return PTR_ERR(mv98dx3236_resume_base);
>
> Should be PTR_ERR(base)?
Yes. I decided to add the local variable at the last minute.
>
>> + }
>> +
>> + mv98dx3236_resume_base = base;
>> + of_node_put(np);
>> + return 0;
>> +}
>
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC
2017-01-06 4:14 ` [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
2017-01-06 6:36 ` Stephen Boyd
@ 2017-01-09 18:40 ` Rob Herring
1 sibling, 0 replies; 43+ messages in thread
From: Rob Herring @ 2017-01-09 18:40 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jan 06, 2017 at 05:14:59PM +1300, Chris Packham wrote:
> Compared to the armada-xp the 98DX3336 uses different registers to set
> the boot address for the secondary CPU so a new enable-method is needed.
> This will only work if the machine definition doesn't define an overall
> smp_ops because there is not currently a way of overriding this from the
> device tree if it is set in the machine definition.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - Document new enable-method value
> - Correct some references from 98DX4521 to 98DX3236
>
> Changes in v3:
> - Simplify mv98dx3236_resume_init by using of_io_request_and_map()
>
> Documentation/devicetree/bindings/arm/cpus.txt | 1 +
> .../bindings/arm/marvell/98dx3236-resume-ctrl.txt | 18 ++++++++
Acked-by: Rob Herring <robh@kernel.org>
> arch/arm/mach-mvebu/Makefile | 1 +
> arch/arm/mach-mvebu/common.h | 1 +
> arch/arm/mach-mvebu/platsmp.c | 43 ++++++++++++++++++
> arch/arm/mach-mvebu/pmsu-98dx3236.c | 52 ++++++++++++++++++++++
> 6 files changed, 116 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236-resume-ctrl.txt
> create mode 100644 arch/arm/mach-mvebu/pmsu-98dx3236.c
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
2017-01-06 4:14 ` Chris Packham
2017-01-06 4:14 ` [PATCHv3 1/5] clk: mvebu: support for 98DX3236 SoC Chris Packham
2017-01-06 4:14 ` [PATCHv3 2/5] arm: mvebu: support for SMP on 98DX3336 SoC Chris Packham
@ 2017-01-06 4:15 ` Chris Packham
2017-01-09 18:41 ` Rob Herring
2017-01-11 14:44 ` Linus Walleij
2017-01-06 4:15 ` [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
2017-01-06 4:15 ` [PATCHv3 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards Chris Packham
4 siblings, 2 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-06 4:15 UTC (permalink / raw)
To: linux-arm-kernel
From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
from Marvell.
Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- include sdio support for the 98DX4251
Changes in v3:
- None
.../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++++
drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++++++++++
2 files changed, 201 insertions(+)
create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
diff --git a/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
new file mode 100644
index 000000000000..d4e6ecdfc853
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
@@ -0,0 +1,46 @@
+* Marvell 98dx3236 pinctrl driver for mpp
+
+Please refer to marvell,mvebu-pinctrl.txt in this directory for common binding
+part and usage
+
+Required properties:
+- compatible: "marvell,98dx3236-pinctrl" or "marvell,98dx4251-pinctrl"
+- reg: register specifier of MPP registers
+
+This driver supports all 98dx3236, 98dx3336 and 98dx4251 variants
+
+name pins functions
+================================================================================
+mpp0 0 gpio, spi0(mosi), dev(ad8)
+mpp1 1 gpio, spi0(miso), dev(ad9)
+mpp2 2 gpio, spi0(sck), dev(ad10)
+mpp3 3 gpio, spi0(cs0), dev(ad11)
+mpp4 4 gpio, spi0(cs1), smi(mdc), dev(cs0)
+mpp5 5 gpio, pex(rsto), sd0(cmd), dev(bootcs)
+mpp6 6 gpio, sd0(clk), dev(a2)
+mpp7 7 gpio, sd0(d0), dev(ale0)
+mpp8 8 gpio, sd0(d1), dev(ale1)
+mpp9 9 gpio, sd0(d2), dev(ready0)
+mpp10 10 gpio, sd0(d3), dev(ad12)
+mpp11 11 gpio, uart1(rxd), uart0(cts), dev(ad13)
+mpp12 12 gpio, uart1(txd), uart0(rts), dev(ad14)
+mpp13 13 gpio, intr(out), dev(ad15)
+mpp14 14 gpio, i2c0(sck)
+mpp15 15 gpio, i2c0(sda)
+mpp16 16 gpio, dev(oe)
+mpp17 17 gpio, dev(clk)
+mpp18 18 gpio, uart1(txd)
+mpp19 19 gpio, uart1(rxd), dev(rb)
+mpp20 20 gpio, dev(we)
+mpp21 21 gpio, dev(ad0)
+mpp22 22 gpio, dev(ad1)
+mpp23 23 gpio, dev(ad2)
+mpp24 24 gpio, dev(ad3)
+mpp25 25 gpio, dev(ad4)
+mpp26 26 gpio, dev(ad5)
+mpp27 27 gpio, dev(ad6)
+mpp28 28 gpio, dev(ad7)
+mpp29 29 gpio, dev(a0)
+mpp30 30 gpio, dev(a1)
+mpp31 31 gpio, slv_smi(mdc), smi(mdc), dev(we1)
+mpp32 32 gpio, slv_smi(mdio), smi(mdio), dev(cs1)
diff --git a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
index e4ea71a9d985..554eeae8cd21 100644
--- a/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
+++ b/drivers/pinctrl/mvebu/pinctrl-armada-xp.c
@@ -49,6 +49,10 @@ enum armada_xp_variant {
V_MV78460 = BIT(2),
V_MV78230_PLUS = (V_MV78230 | V_MV78260 | V_MV78460),
V_MV78260_PLUS = (V_MV78260 | V_MV78460),
+ V_98DX3236 = BIT(3),
+ V_98DX3336 = BIT(4),
+ V_98DX4251 = BIT(5),
+ V_98DX3236_PLUS = (V_98DX3236 | V_98DX3336 | V_98DX4251),
};
static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
@@ -360,6 +364,130 @@ static struct mvebu_mpp_mode armada_xp_mpp_modes[] = {
MPP_VAR_FUNCTION(0x1, "dev", "ad31", V_MV78260_PLUS)),
};
+static struct mvebu_mpp_mode mv98dx3236_mpp_modes[] = {
+ MPP_MODE(0,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "mosi", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad8", V_98DX3236_PLUS)),
+ MPP_MODE(1,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "miso", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad9", V_98DX3236_PLUS)),
+ MPP_MODE(2,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "csk", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad10", V_98DX3236_PLUS)),
+ MPP_MODE(3,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "cs0", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad11", V_98DX3236_PLUS)),
+ MPP_MODE(4,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "spi0", "cs1", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "cs0", V_98DX3236_PLUS)),
+ MPP_MODE(5,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "pex", "rsto", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "cmd", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "bootcs0", V_98DX3236_PLUS)),
+ MPP_MODE(6,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "clk", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "a2", V_98DX3236_PLUS)),
+ MPP_MODE(7,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d0", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ale0", V_98DX3236_PLUS)),
+ MPP_MODE(8,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d1", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ale1", V_98DX3236_PLUS)),
+ MPP_MODE(9,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d2", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ready0", V_98DX3236_PLUS)),
+ MPP_MODE(10,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "sd0", "d3", V_98DX4251),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad12", V_98DX3236_PLUS)),
+ MPP_MODE(11,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "uart1", "rxd", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart0", "cts", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad13", V_98DX3236_PLUS)),
+ MPP_MODE(12,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x2, "uart1", "txd", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart0", "rts", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad14", V_98DX3236_PLUS)),
+ MPP_MODE(13,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "intr", "out", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "ad15", V_98DX3236_PLUS)),
+ MPP_MODE(14,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "i2c0", "sck", V_98DX3236_PLUS)),
+ MPP_MODE(15,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "i2c0", "sda", V_98DX3236_PLUS)),
+ MPP_MODE(16,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "oe", V_98DX3236_PLUS)),
+ MPP_MODE(17,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "clkout", V_98DX3236_PLUS)),
+ MPP_MODE(18,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart1", "txd", V_98DX3236_PLUS)),
+ MPP_MODE(19,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "uart1", "rxd", V_98DX3236_PLUS)),
+ MPP_MODE(20,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "we0", V_98DX3236_PLUS)),
+ MPP_MODE(21,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad0", V_98DX3236_PLUS)),
+ MPP_MODE(22,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad1", V_98DX3236_PLUS)),
+ MPP_MODE(23,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad2", V_98DX3236_PLUS)),
+ MPP_MODE(24,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad3", V_98DX3236_PLUS)),
+ MPP_MODE(25,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad4", V_98DX3236_PLUS)),
+ MPP_MODE(26,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad5", V_98DX3236_PLUS)),
+ MPP_MODE(27,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad6", V_98DX3236_PLUS)),
+ MPP_MODE(28,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "ad7", V_98DX3236_PLUS)),
+ MPP_MODE(29,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "a0", V_98DX3236_PLUS)),
+ MPP_MODE(30,
+ MPP_VAR_FUNCTION(0x0, "gpo", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "dev", "a1", V_98DX3236_PLUS)),
+ MPP_MODE(31,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "slv_smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdc", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "we1", V_98DX3236_PLUS)),
+ MPP_MODE(32,
+ MPP_VAR_FUNCTION(0x0, "gpio", NULL, V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x1, "slv_smi", "mdio", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x3, "smi", "mdio", V_98DX3236_PLUS),
+ MPP_VAR_FUNCTION(0x4, "dev", "cs1", V_98DX3236_PLUS)),
+};
+
static struct mvebu_pinctrl_soc_info armada_xp_pinctrl_info;
static const struct of_device_id armada_xp_pinctrl_of_match[] = {
@@ -375,6 +503,14 @@ static const struct of_device_id armada_xp_pinctrl_of_match[] = {
.compatible = "marvell,mv78460-pinctrl",
.data = (void *) V_MV78460,
},
+ {
+ .compatible = "marvell,98dx3236-pinctrl",
+ .data = (void *) V_98DX3236,
+ },
+ {
+ .compatible = "marvell,98dx4251-pinctrl",
+ .data = (void *) V_98DX4251,
+ },
{ },
};
@@ -407,6 +543,14 @@ static struct pinctrl_gpio_range mv78460_mpp_gpio_ranges[] = {
MPP_GPIO_RANGE(2, 64, 64, 3),
};
+static struct mvebu_mpp_ctrl mv98dx3236_mpp_controls[] = {
+ MPP_FUNC_CTRL(0, 32, NULL, armada_xp_mpp_ctrl),
+};
+
+static struct pinctrl_gpio_range mv98dx3236_mpp_gpio_ranges[] = {
+ MPP_GPIO_RANGE(0, 0, 0, 32),
+};
+
static int armada_xp_pinctrl_suspend(struct platform_device *pdev,
pm_message_t state)
{
@@ -488,6 +632,17 @@ static int armada_xp_pinctrl_probe(struct platform_device *pdev)
soc->gpioranges = mv78460_mpp_gpio_ranges;
soc->ngpioranges = ARRAY_SIZE(mv78460_mpp_gpio_ranges);
break;
+ case V_98DX3236:
+ case V_98DX3336:
+ case V_98DX4251:
+ /* fall-through */
+ soc->controls = mv98dx3236_mpp_controls;
+ soc->ncontrols = ARRAY_SIZE(mv98dx3236_mpp_controls);
+ soc->modes = mv98dx3236_mpp_modes;
+ soc->nmodes = mv98dx3236_mpp_controls[0].npins;
+ soc->gpioranges = mv98dx3236_mpp_gpio_ranges;
+ soc->ngpioranges = ARRAY_SIZE(mv98dx3236_mpp_gpio_ranges);
+ break;
}
nregs = DIV_ROUND_UP(soc->nmodes, MVEBU_MPPS_PER_REG);
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
2017-01-06 4:15 ` [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC Chris Packham
@ 2017-01-09 18:41 ` Rob Herring
2017-01-11 14:44 ` Linus Walleij
1 sibling, 0 replies; 43+ messages in thread
From: Rob Herring @ 2017-01-09 18:41 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jan 06, 2017 at 05:15:00PM +1300, Chris Packham wrote:
> From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>
> This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
> from Marvell.
>
> Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - include sdio support for the 98DX4251
> Changes in v3:
> - None
>
> .../pinctrl/marvell,armada-98dx3236-pinctrl.txt | 46 ++++++
Acked-by: Rob Herring <robh@kernel.org>
> drivers/pinctrl/mvebu/pinctrl-armada-xp.c | 155 +++++++++++++++++++++
> 2 files changed, 201 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/marvell,armada-98dx3236-pinctrl.txt
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
2017-01-06 4:15 ` [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC Chris Packham
2017-01-09 18:41 ` Rob Herring
@ 2017-01-11 14:44 ` Linus Walleij
2017-01-11 20:55 ` Sebastian Hesselbarth
1 sibling, 1 reply; 43+ messages in thread
From: Linus Walleij @ 2017-01-11 14:44 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jan 6, 2017 at 5:15 AM, Chris Packham
<chris.packham@alliedtelesis.co.nz> wrote:
> From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>
> This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
> from Marvell.
>
> Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
I am waiting for an ACK or comment from the maintainers on
this patch. Sebastian?
Yours,
Linus Walleij
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
2017-01-11 14:44 ` Linus Walleij
@ 2017-01-11 20:55 ` Sebastian Hesselbarth
2017-01-12 9:13 ` Chris Packham
0 siblings, 1 reply; 43+ messages in thread
From: Sebastian Hesselbarth @ 2017-01-11 20:55 UTC (permalink / raw)
To: linux-arm-kernel
On 01/11/2017 03:44 PM, Linus Walleij wrote:
> On Fri, Jan 6, 2017 at 5:15 AM, Chris Packham
> <chris.packham@alliedtelesis.co.nz> wrote:
>
>> From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>>
>> This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
>> from Marvell.
>>
>> Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>
> I am waiting for an ACK or comment from the maintainers on
> this patch. Sebastian?
Sorry for the ignorance.
I don't have the patch to reply to inline, but:
- In the driver MPP_MODE2, spi0 there is a typo "csk" instead of "sck".
- MPP_MODE5 binding "dev","bootcs" and driver "dev","bootcs0" differ.
- MPP_MODE6 binding "gpio" and driver "gpo" differ.
- MPP_MODE17 binding "dev","clk" and driver "dev","clkout" differ.
- MPP_MODE19 binding mentiones "dev","rb" but driver does not.
- MPP_MODE20 binding "gpio" and driver "gpo" differ.
- MPP_MODE20 binding "dev","we" and driver "dev","we0" differ.
- MPP_MODE21 through MPP_MODE30 binding "gpio" and driver "gpo" differ.
- remove spaces before "0, 0" in mv98dx3236_mpp_gpio_ranges.
Most of it is cosmetic stuff, so if you fix it feel free to add my
Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Sebastian
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC
2017-01-11 20:55 ` Sebastian Hesselbarth
@ 2017-01-12 9:13 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-12 9:13 UTC (permalink / raw)
To: linux-arm-kernel
On 12/01/17 09:56, Sebastian Hesselbarth wrote:
> On 01/11/2017 03:44 PM, Linus Walleij wrote:
>> On Fri, Jan 6, 2017 at 5:15 AM, Chris Packham
>> <chris.packham@alliedtelesis.co.nz> wrote:
>>
>>> From: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>>>
>>> This pinctrl driver supports the 98DX3236, 98DX3336 and 98DX4251 SoCs
>>> from Marvell.
>>>
>>> Signed-off-by: Kalyan Kinthada <kalyan.kinthada@alliedtelesis.co.nz>
>>> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
>>
>> I am waiting for an ACK or comment from the maintainers on
>> this patch. Sebastian?
>
> Sorry for the ignorance.
>
> I don't have the patch to reply to inline, but:
>
> - In the driver MPP_MODE2, spi0 there is a typo "csk" instead of "sck".
> - MPP_MODE5 binding "dev","bootcs" and driver "dev","bootcs0" differ.
> - MPP_MODE6 binding "gpio" and driver "gpo" differ.
> - MPP_MODE17 binding "dev","clk" and driver "dev","clkout" differ.
> - MPP_MODE19 binding mentiones "dev","rb" but driver does not.
> - MPP_MODE20 binding "gpio" and driver "gpo" differ.
> - MPP_MODE20 binding "dev","we" and driver "dev","we0" differ.
> - MPP_MODE21 through MPP_MODE30 binding "gpio" and driver "gpo" differ.
> - remove spaces before "0, 0" in mv98dx3236_mpp_gpio_ranges.
>
> Most of it is cosmetic stuff, so if you fix it feel free to add my
>
> Acked-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Hi Sebastian,
Hopefully I can get a v4 out with the above fixed soon.
One point on "gpio" vs "gpo" this one isn't a typo. Some of these pins
can be driven as outputs but can't be used as inputs. From a pinctrl
driver point of view there is no difference but I did want to convey
that from a system design point of view if you really need something to
be an input you shouldn't use one of these pins. This is also noted in
the datasheets so it doesn't necessarily need repeating. If you still
want me to use "gpio" in the code and binding I'm happy to do so.
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-06 4:14 ` Chris Packham
` (2 preceding siblings ...)
2017-01-06 4:15 ` [PATCHv3 3/5] pinctrl: mvebu: pinctrl driver for 98DX3236 SoC Chris Packham
@ 2017-01-06 4:15 ` Chris Packham
2017-01-09 18:44 ` Rob Herring
2017-01-26 15:09 ` Gregory CLEMENT
2017-01-06 4:15 ` [PATCHv3 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards Chris Packham
4 siblings, 2 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-06 4:15 UTC (permalink / raw)
To: linux-arm-kernel
The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
with integrated CPUs. They are similar to the Armada XP SoCs but have
different I/O interfaces.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Changes in v2:
- Update devicetree binding documentation to reflect that 98DX3336 and
984251 are supersets of 98DX3236.
- disable crypto block
- disable sdio for 98DX3236, enable for 98DX4251
Changes in v3:
- fix typo 4521 -> 4251
- document prestera bindings
- rework corediv-clock binding
- add label to packet processor node
- add new compativle string for DFX server
.../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
.../devicetree/bindings/net/marvell,prestera.txt | 50 ++++
arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 254 +++++++++++++++++++++
arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 76 ++++++
arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 90 ++++++++
5 files changed, 493 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
create mode 100644 Documentation/devicetree/bindings/net/marvell,prestera.txt
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
diff --git a/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
new file mode 100644
index 000000000000..64e8c73fc5ab
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
@@ -0,0 +1,23 @@
+Marvell 98DX3236, 98DX3336 and 98DX4251 Platforms Device Tree Bindings
+----------------------------------------------------------------------
+
+Boards with a SoC of the Marvell 98DX3236, 98DX3336 and 98DX4251 families
+shall have the following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3236"
+
+In addition, boards using the Marvell 98DX3336 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx3336"
+
+In addition, boards using the Marvell 98DX4251 SoC shall have the
+following property:
+
+Required root node property:
+
+compatible: must contain "marvell,armadaxp-98dx4251"
diff --git a/Documentation/devicetree/bindings/net/marvell,prestera.txt b/Documentation/devicetree/bindings/net/marvell,prestera.txt
new file mode 100644
index 000000000000..5fbab29718e8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/marvell,prestera.txt
@@ -0,0 +1,50 @@
+Marvell Prestera Switch Chip bindings
+-------------------------------------
+
+Required properties:
+- compatible: one of the following
+ "marvell,prestera-98dx3236",
+ "marvell,prestera-98dx3336",
+ "marvell,prestera-98dx4251",
+- reg: address and length of the register set for the device.
+- interrupts: interrupt for the device
+
+Optional properties:
+- dfx: phandle reference to the "DFX Server" node
+
+Example:
+
+switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+};
+
+DFX Server bindings
+-------------------
+
+Required properties:
+- compatible: must be "marvell,dfx-server"
+- reg: address and length of the register set for the device.
+
+Example:
+
+dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx: dfx at 0 {
+ compatible = "marvell,dfx-server";
+ reg = <0 0x100000>;
+ };
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
new file mode 100644
index 000000000000..4b7b2fe3b682
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
@@ -0,0 +1,254 @@
+/*
+ * Device Tree Include file for Marvell 98dx3236 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3236 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp.dtsi"
+
+/ {
+ model = "Marvell 98DX3236 SoC";
+ compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ aliases {
+ gpio0 = &gpio0;
+ gpio1 = &gpio1;
+ gpio2 = &gpio2;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ enable-method = "marvell,98dx3236-smp";
+
+ cpu at 0 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <0>;
+ clocks = <&cpuclk 0>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ /*
+ * 98DX3236 has 1 x1 PCIe unit Gen2.0: One unit can be
+ */
+ pcie-controller {
+ compatible = "marvell,armada-xp-pcie";
+ status = "disabled";
+ device_type = "pci";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ msi-parent = <&mpic>;
+ bus-range = <0x00 0xff>;
+
+ ranges =
+ <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
+ 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
+ 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
+ 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */>;
+
+ pcie at 1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
+ reg = <0x0800 0 0 0 0>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+ #interrupt-cells = <1>;
+ ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
+ 0x81000000 0 0 0x81000000 0x1 0 1 0>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &mpic 58>;
+ marvell,pcie-port = <0>;
+ marvell,pcie-lane = <0>;
+ clocks = <&gateclk 5>;
+ status = "disabled";
+ };
+ };
+
+ internal-regs {
+ coreclk: mvebu-sar at 18230 {
+ compatible = "marvell,mv98dx3236-core-clock";
+ };
+
+ cpuclk: clock-complex at 18700 {
+ compatible = "marvell,mv98dx3236-cpu-clock";
+ };
+
+ corediv-clock at 18740 {
+ status = "disabled";
+ };
+
+ xor at 60900 {
+ status = "disabled";
+ };
+
+ crypto at 90000 {
+ status = "disabled";
+ };
+
+ xor at f0900 {
+ status = "disabled";
+ };
+
+ xor at f0800 {
+ compatible = "marvell,orion-xor";
+ reg = <0xf0800 0x100
+ 0xf0a00 0x100>;
+ clocks = <&gateclk 22>;
+ status = "okay";
+
+ xor10 {
+ interrupts = <51>;
+ dmacap,memcpy;
+ dmacap,xor;
+ };
+ xor11 {
+ interrupts = <52>;
+ dmacap,memcpy;
+ dmacap,xor;
+ dmacap,memset;
+ };
+ };
+
+ gpio0: gpio at 18100 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18100 0x40>;
+ ngpios = <32>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <82>, <83>, <84>, <85>;
+ };
+
+ /* does not exist */
+ gpio1: gpio at 18140 {
+ compatible = "marvell,orion-gpio";
+ reg = <0x18140 0x40>;
+ status = "disabled";
+ };
+
+ gpio2: gpio at 18180 { /* rework some properties */
+ compatible = "marvell,orion-gpio";
+ reg = <0x18180 0x40>;
+ ngpios = <1>; /* only gpio #32 */
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ interrupts = <87>;
+ };
+
+ nand: nand at d0000 {
+ clocks = <&dfx_coredivclk 0>;
+ };
+ };
+
+ dfx-registers {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
+
+ dfx_coredivclk: corediv-clock at f8268 {
+ compatible = "marvell,mv98dx3236-corediv-clock";
+ reg = <0xf8268 0xc>;
+ #clock-cells = <1>;
+ clocks = <&mainpll>;
+ clock-output-names = "nand";
+ };
+
+ dfx: dfx at 0 {
+ compatible = "marvell,dfx-server";
+ reg = <0 0x100000>;
+ };
+ };
+
+ switch {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
+
+ pp0: packet-processor at 0 {
+ compatible = "marvell,prestera-98dx3236";
+ reg = <0 0x4000000>;
+ interrupts = <33>, <34>, <35>;
+ dfx = <&dfx>;
+ };
+ };
+ };
+};
+
+&pinctrl {
+ compatible = "marvell,98dx3236-pinctrl";
+
+ spi0_pins: spi0-pins {
+ marvell,pins = "mpp0", "mpp1",
+ "mpp2", "mpp3";
+ marvell,function = "spi0";
+ };
+};
+
+&sdio {
+ status = "disabled";
+};
+
+&crypto_sram0 {
+ status = "disabled";
+};
+
+&crypto_sram1 {
+ status = "disabled";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
new file mode 100644
index 000000000000..a9b0f47f8df9
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
@@ -0,0 +1,76 @@
+/*
+ * Device Tree Include file for Marvell 98dx3336 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx3336 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+ model = "Marvell 98DX3336 SoC";
+ compatible = "marvell,armadaxp-98dx3336", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ cpus {
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+ };
+ };
+ };
+};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx3336";
+};
diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
new file mode 100644
index 000000000000..446e6e65ec59
--- /dev/null
+++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
@@ -0,0 +1,90 @@
+/*
+ * Device Tree Include file for Marvell 98dx4521 family SoC
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Contains definitions specific to the 98dx4521 SoC that are not
+ * common to all Armada XP SoCs.
+ */
+
+#include "armada-xp-98dx3236.dtsi"
+
+/ {
+ model = "Marvell 98DX4251 SoC";
+ compatible = "marvell,armadaxp-98dx4521", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ cpus {
+ cpu at 1 {
+ device_type = "cpu";
+ compatible = "marvell,sheeva-v7";
+ reg = <1>;
+ clocks = <&cpuclk 1>;
+ clock-latency = <1000000>;
+ };
+ };
+
+ soc {
+ internal-regs {
+ resume at 20980 {
+ compatible = "marvell,98dx3336-resume-ctrl";
+ reg = <0x20980 0x10>;
+ };
+ };
+ };
+};
+
+&sdio {
+ status = "okay";
+};
+
+&pinctrl {
+ compatible = "marvell,98dx4251-pinctrl";
+
+ sdio_pins: sdio-pins {
+ marvell,pins = "mpp5", "mpp6", "mpp7",
+ "mpp8", "mpp9", "mpp10";
+ marvell,function = "sd0";
+ };
+};
+
+&pp0 {
+ compatible = "marvell,prestera-98dx4251";
+};
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-06 4:15 ` [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
@ 2017-01-09 18:44 ` Rob Herring
2017-01-26 15:09 ` Gregory CLEMENT
1 sibling, 0 replies; 43+ messages in thread
From: Rob Herring @ 2017-01-09 18:44 UTC (permalink / raw)
To: linux-arm-kernel
On Fri, Jan 06, 2017 at 05:15:01PM +1300, Chris Packham wrote:
> The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
> with integrated CPUs. They are similar to the Armada XP SoCs but have
> different I/O interfaces.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> Changes in v2:
> - Update devicetree binding documentation to reflect that 98DX3336 and
> 984251 are supersets of 98DX3236.
> - disable crypto block
> - disable sdio for 98DX3236, enable for 98DX4251
> Changes in v3:
> - fix typo 4521 -> 4251
> - document prestera bindings
> - rework corediv-clock binding
> - add label to packet processor node
> - add new compativle string for DFX server
>
> .../devicetree/bindings/arm/marvell/98dx3236.txt | 23 ++
> .../devicetree/bindings/net/marvell,prestera.txt | 50 ++++
> arch/arm/boot/dts/armada-xp-98dx3236.dtsi | 254 +++++++++++++++++++++
> arch/arm/boot/dts/armada-xp-98dx3336.dtsi | 76 ++++++
> arch/arm/boot/dts/armada-xp-98dx4251.dtsi | 90 ++++++++
> 5 files changed, 493 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/98dx3236.txt
> create mode 100644 Documentation/devicetree/bindings/net/marvell,prestera.txt
> create mode 100644 arch/arm/boot/dts/armada-xp-98dx3236.dtsi
> create mode 100644 arch/arm/boot/dts/armada-xp-98dx3336.dtsi
> create mode 100644 arch/arm/boot/dts/armada-xp-98dx4251.dtsi
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-06 4:15 ` [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
2017-01-09 18:44 ` Rob Herring
@ 2017-01-26 15:09 ` Gregory CLEMENT
2017-01-26 20:07 ` Chris Packham
2017-01-26 20:24 ` Chris Packham
1 sibling, 2 replies; 43+ messages in thread
From: Gregory CLEMENT @ 2017-01-26 15:09 UTC (permalink / raw)
To: linux-arm-kernel
Hi Chris,
On ven., janv. 06 2017, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:
> The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
> with integrated CPUs. They are similar to the Armada XP SoCs but have
> different I/O interfaces.
Before sending a new version I have a few remarks:
> diff --git a/arch/arm/boot/dts/armada-xp-98dx3236.dtsi b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
> new file mode 100644
> index 000000000000..4b7b2fe3b682
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-xp-98dx3236.dtsi
> @@ -0,0 +1,254 @@
> +/*
> + * Device Tree Include file for Marvell 98dx3236 family SoC
> + *
> + * Copyright (C) 2016 Allied Telesis Labs
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
There are few characters missing in the licence text, have a look on:
http://git.infradead.org/linux-mvebu.git/commitdiff/24f0b6fe52d21b5c59c4e948daae2234a39a25b2?hp=7ce7d89f48834cefece7804d38fc5d85382edf77
> + *
> + * Contains definitions specific to the 98dx3236 SoC that are not
> + * common to all Armada XP SoCs.
> + */
> +
> +#include "armada-xp.dtsi"
> +
> +/ {
> + model = "Marvell 98DX3236 SoC";
> + compatible = "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
> +
> + aliases {
> + gpio0 = &gpio0;
> + gpio1 = &gpio1;
> + gpio2 = &gpio2;
> + };
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + enable-method = "marvell,98dx3236-smp";
> +
> + cpu at 0 {
> + device_type = "cpu";
> + compatible = "marvell,sheeva-v7";
> + reg = <0>;
> + clocks = <&cpuclk 0>;
> + clock-latency = <1000000>;
> + };
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
> + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
> + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
> + MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
> + MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
> +
> + /*
> + * 98DX3236 has 1 x1 PCIe unit Gen2.0: One unit can be
The comment had been cut
> + */
> + pcie-controller {
Please use a node label here as we have done in:
http://git.infradead.org/linux-mvebu.git/commitdiff/11f7135bb9dbe7ae3bb9a125e6123d4096a7e69e?hp=e72996b80d53b9b7616c8b68304ce4c422b4ddd1
Also use an address:
http://git.infradead.org/linux-mvebu.git/commitdiff/007d05d898050ffc70fd2737896528c5069f7269
> + compatible = "marvell,armada-xp-pcie";
> + status = "disabled";
> + device_type = "pci";
> +
> + #address-cells = <3>;
> + #size-cells = <2>;
> +
> + msi-parent = <&mpic>;
> + bus-range = <0x00 0xff>;
> +
> + ranges =
> + <0x82000000 0 0x40000 MBUS_ID(0xf0, 0x01) 0x40000 0 0x00002000 /* Port 0.0 registers */
> + 0x82000000 0x1 0 MBUS_ID(0x04, 0xe8) 0 1 0 /* Port 0.0 MEM */
> + 0x81000000 0x1 0 MBUS_ID(0x04, 0xe0) 0 1 0 /* Port 0.0 IO */
> + 0x82000000 0x2 0 MBUS_ID(0x04, 0xd8) 0 1 0 /* Port 0.1 MEM */>;
> +
> + pcie at 1,0 {
node label
> + device_type = "pci";
> + assigned-addresses = <0x82000800 0 0x40000 0 0x2000>;
> + reg = <0x0800 0 0 0 0>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + #interrupt-cells = <1>;
> + ranges = <0x82000000 0 0 0x82000000 0x1 0 1 0
> + 0x81000000 0 0 0x81000000 0x1 0 1 0>;
> + interrupt-map-mask = <0 0 0 0>;
> + interrupt-map = <0 0 0 0 &mpic 58>;
> + marvell,pcie-port = <0>;
> + marvell,pcie-lane = <0>;
> + clocks = <&gateclk 5>;
> + status = "disabled";
> + };
> + };
> +
> + internal-regs {
> + coreclk: mvebu-sar at 18230 {
> + compatible = "marvell,mv98dx3236-core-clock";
> + };
> +
> + cpuclk: clock-complex at 18700 {
> + compatible = "marvell,mv98dx3236-cpu-clock";
> + };
> +
> + corediv-clock at 18740 {
> + status = "disabled";
> + };
> +
> + xor at 60900 {
> + status = "disabled";
> + };
> +
> + crypto at 90000 {
> + status = "disabled";
> + };
> +
> + xor at f0900 {
> + status = "disabled";
> + };
> +
> + xor at f0800 {
> + compatible = "marvell,orion-xor";
> + reg = <0xf0800 0x100
> + 0xf0a00 0x100>;
> + clocks = <&gateclk 22>;
> + status = "okay";
> +
> + xor10 {
> + interrupts = <51>;
> + dmacap,memcpy;
> + dmacap,xor;
> + };
> + xor11 {
> + interrupts = <52>;
> + dmacap,memcpy;
> + dmacap,xor;
> + dmacap,memset;
> + };
> + };
> +
> + gpio0: gpio at 18100 {
> + compatible = "marvell,orion-gpio";
> + reg = <0x18100 0x40>;
> + ngpios = <32>;
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupts = <82>, <83>, <84>, <85>;
> + };
> +
> + /* does not exist */
> + gpio1: gpio at 18140 {
> + compatible = "marvell,orion-gpio";
> + reg = <0x18140 0x40>;
> + status = "disabled";
> + };
> +
> + gpio2: gpio at 18180 { /* rework some properties */
> + compatible = "marvell,orion-gpio";
> + reg = <0x18180 0x40>;
> + ngpios = <1>; /* only gpio #32 */
> + gpio-controller;
> + #gpio-cells = <2>;
> + interrupt-controller;
> + #interrupt-cells = <2>;
> + interrupts = <87>;
> + };
> +
> + nand: nand at d0000 {
> + clocks = <&dfx_coredivclk 0>;
> + };
> + };
> +
> + dfx-registers {
node label
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 MBUS_ID(0x08, 0x00) 0 0x100000>;
> +
> + dfx_coredivclk: corediv-clock at f8268 {
> + compatible = "marvell,mv98dx3236-corediv-clock";
> + reg = <0xf8268 0xc>;
> + #clock-cells = <1>;
> + clocks = <&mainpll>;
> + clock-output-names = "nand";
> + };
> +
> + dfx: dfx at 0 {
> + compatible = "marvell,dfx-server";
> + reg = <0 0x100000>;
> + };
> + };
> +
> + switch {
node label
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 MBUS_ID(0x03, 0x00) 0 0x100000>;
> +
> + pp0: packet-processor at 0 {
> + compatible = "marvell,prestera-98dx3236";
> + reg = <0 0x4000000>;
> + interrupts = <33>, <34>, <35>;
> + dfx = <&dfx>;
> + };
> + };
> + };
> +};
> +
> +&pinctrl {
> + compatible = "marvell,98dx3236-pinctrl";
> +
> + spi0_pins: spi0-pins {
> + marvell,pins = "mpp0", "mpp1",
> + "mpp2", "mpp3";
> + marvell,function = "spi0";
> + };
> +};
> +
> +&sdio {
> + status = "disabled";
> +};
> +
> +&crypto_sram0 {
> + status = "disabled";
> +};
> +
> +&crypto_sram1 {
> + status = "disabled";
> +};
same comments for the following device tree, in general you can refer to
this series:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/468585.html
> diff --git a/arch/arm/boot/dts/armada-xp-98dx3336.dtsi b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
> new file mode 100644
> index 000000000000..a9b0f47f8df9
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-xp-98dx3336.dtsi
> @@ -0,0 +1,76 @@
> +/*
> + * Device Tree Include file for Marvell 98dx3336 family SoC
> + *
> + * Copyright (C) 2016 Allied Telesis Labs
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + * Contains definitions specific to the 98dx3336 SoC that are not
> + * common to all Armada XP SoCs.
> + */
> +
> +#include "armada-xp-98dx3236.dtsi"
> +
> +/ {
> + model = "Marvell 98DX3336 SoC";
> + compatible = "marvell,armadaxp-98dx3336", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
> +
> + cpus {
> + cpu at 1 {
> + device_type = "cpu";
> + compatible = "marvell,sheeva-v7";
> + reg = <1>;
> + clocks = <&cpuclk 1>;
> + clock-latency = <1000000>;
> + };
> + };
> +
> + soc {
> + internal-regs {
Why the following node is not part of the dtsi?
Gregory
> + resume at 20980 {
> + compatible = "marvell,98dx3336-resume-ctrl";
> + reg = <0x20980 0x10>;
> + };
> + };
> + };
> +};
> +
> +&pp0 {
> + compatible = "marvell,prestera-98dx3336";
> +};
> diff --git a/arch/arm/boot/dts/armada-xp-98dx4251.dtsi b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
> new file mode 100644
> index 000000000000..446e6e65ec59
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-xp-98dx4251.dtsi
> @@ -0,0 +1,90 @@
> +/*
> + * Device Tree Include file for Marvell 98dx4521 family SoC
> + *
> + * Copyright (C) 2016 Allied Telesis Labs
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + * Contains definitions specific to the 98dx4521 SoC that are not
> + * common to all Armada XP SoCs.
> + */
> +
> +#include "armada-xp-98dx3236.dtsi"
> +
> +/ {
> + model = "Marvell 98DX4251 SoC";
> + compatible = "marvell,armadaxp-98dx4521", "marvell,armadaxp-98dx3236", "marvell,armadaxp", "marvell,armada-370-xp";
> +
> + cpus {
> + cpu at 1 {
> + device_type = "cpu";
> + compatible = "marvell,sheeva-v7";
> + reg = <1>;
> + clocks = <&cpuclk 1>;
> + clock-latency = <1000000>;
> + };
> + };
> +
> + soc {
> + internal-regs {
> + resume at 20980 {
> + compatible = "marvell,98dx3336-resume-ctrl";
> + reg = <0x20980 0x10>;
> + };
> + };
> + };
> +};
> +
> +&sdio {
> + status = "okay";
> +};
> +
> +&pinctrl {
> + compatible = "marvell,98dx4251-pinctrl";
> +
> + sdio_pins: sdio-pins {
> + marvell,pins = "mpp5", "mpp6", "mpp7",
> + "mpp8", "mpp9", "mpp10";
> + marvell,function = "sd0";
> + };
> +};
> +
> +&pp0 {
> + compatible = "marvell,prestera-98dx4251";
> +};
> --
> 2.11.0.24.ge6920cf
>
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-26 15:09 ` Gregory CLEMENT
@ 2017-01-26 20:07 ` Chris Packham
2017-01-26 20:24 ` Chris Packham
1 sibling, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-26 20:07 UTC (permalink / raw)
To: linux-arm-kernel
On 27/01/17 04:10, Gregory CLEMENT wrote:
> Hi Chris,
>
> On ven., janv. 06 2017, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:
>
>> The Marvell 98DX3236, 98DX3336, 98DX4521 and variants are switch ASICs
>> with integrated CPUs. They are similar to the Armada XP SoCs but have
>> different I/O interfaces.
>
> Before sending a new version I have a few remarks:
>
>
[snip]
I'll update the dtsi files to use the node labels and correct the
commends as requested
>
> Why the following node is not part of the dtsi?
>
> Gregory
>
>> + resume at 20980 {
>> + compatible = "marvell,98dx3336-resume-ctrl";
>> + reg = <0x20980 0x10>;
>> + };
>> + };
>> + };
The 98DX9236 has a single ARMv7 core. As such this resume control isn't
present on it. The 98DX3336 and 98DX4521 have dual ARMv7 cores and this
is used to boot the second core (SMP support is a little different
compared to Armada-XP).
In other words {98DX3336, 98DX4521} = 98DX9236 + an additional core. At
the switch packet processor level there are more differences but as far
as the kernel is concerned the only real difference is the number of cores.
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-26 15:09 ` Gregory CLEMENT
2017-01-26 20:07 ` Chris Packham
@ 2017-01-26 20:24 ` Chris Packham
2017-01-26 22:52 ` Chris Packham
1 sibling, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-26 20:24 UTC (permalink / raw)
To: linux-arm-kernel
On 27/01/17 04:10, Gregory CLEMENT wrote:
>> + internal-regs {
[snip]
>> +
>> + dfx-registers {
> node label
>
[snip]
>> + switch {
> node label
>
These are peers to the internal-regs, i.e. parts of the SoC with
mappable windows in the address space. Do they really need a label?
Their subnodes absolutely need (and have) labels.
^ permalink raw reply [flat|nested] 43+ messages in thread* [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs
2017-01-26 20:24 ` Chris Packham
@ 2017-01-26 22:52 ` Chris Packham
0 siblings, 0 replies; 43+ messages in thread
From: Chris Packham @ 2017-01-26 22:52 UTC (permalink / raw)
To: linux-arm-kernel
On 27/01/17 09:24, Chris Packham wrote:
> On 27/01/17 04:10, Gregory CLEMENT wrote:
>>> + internal-regs {
>
> [snip]
>
>>> +
>>> + dfx-registers {
>> node label
>>
>
> [snip]
>
>>> + switch {
>> node label
>>
>
> These are peers to the internal-regs, i.e. parts of the SoC with
> mappable windows in the address space. Do they really need a label?
> Their subnodes absolutely need (and have) labels.
>
Actually the pci-controller is in the same category and that has a label
so I'll add one.
^ permalink raw reply [flat|nested] 43+ messages in thread
* [PATCHv3 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
2017-01-06 4:14 ` Chris Packham
` (3 preceding siblings ...)
2017-01-06 4:15 ` [PATCHv3 4/5] arm: mvebu: Add device tree for 98DX3236 SoCs Chris Packham
@ 2017-01-06 4:15 ` Chris Packham
2017-01-26 15:12 ` Gregory CLEMENT
4 siblings, 1 reply; 43+ messages in thread
From: Chris Packham @ 2017-01-06 4:15 UTC (permalink / raw)
To: linux-arm-kernel
These boards are Marvell's evaluation boards for the 98DX4251 and
98DX3336 SoCs.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
---
Change in v2/v3:
- None
arch/arm/boot/dts/db-dxbc2.dts | 159 ++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++++++++++++++++++++++++
2 files changed, 314 insertions(+)
create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
diff --git a/arch/arm/boot/dts/db-dxbc2.dts b/arch/arm/boot/dts/db-dxbc2.dts
new file mode 100644
index 000000000000..f56786cea5f8
--- /dev/null
+++ b/arch/arm/boot/dts/db-dxbc2.dts
@@ -0,0 +1,159 @@
+/*
+ * Device Tree file for DB-DXBC2 board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx4251.dtsi"
+
+/ {
+ model = "Marvell Bobcat2 Evaluation Board";
+ compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+ serial at 12100 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ clock-frequency = <100000>;
+ status = "okay";
+ };
+
+ mvsdio at d4000 {
+ pinctrl-0 = <&sdio_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ /* No CD or WP GPIOs */
+ broken-cd;
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+
+ partition at u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition at u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition at unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
diff --git a/arch/arm/boot/dts/db-xc3-24g4xg.dts b/arch/arm/boot/dts/db-xc3-24g4xg.dts
new file mode 100644
index 000000000000..5eb89ffb9a7d
--- /dev/null
+++ b/arch/arm/boot/dts/db-xc3-24g4xg.dts
@@ -0,0 +1,155 @@
+/*
+ * Device Tree file for DB-XC3-24G4XG board
+ *
+ * Copyright (C) 2016 Allied Telesis Labs
+ *
+ * Based on armada-xp-db.dts
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ *
+ * Note: this Device Tree assumes that the bootloader has remapped the
+ * internal registers to 0xf1000000 (instead of the default
+ * 0xd0000000). The 0xf1000000 is the default used by the recent,
+ * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
+ * boards were delivered with an older version of the bootloader that
+ * left internal registers mapped at 0xd0000000. If you are in this
+ * situation, you should either update your bootloader (preferred
+ * solution) or the below Device Tree should be adjusted.
+ */
+
+/dts-v1/;
+#include "armada-xp-98dx3336.dtsi"
+
+/ {
+ model = "DB-XC3-24G4XG";
+ compatible = "marvell,db-xc3-24g4xg", "marvell,armadaxp-98dx3336", "marvell,armadaxp", "marvell,armada-370-xp";
+
+ chosen {
+ bootargs = "console=ttyS0,115200 earlyprintk";
+ };
+
+ memory {
+ device_type = "memory";
+ reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
+ MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
+ MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
+ MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
+
+ devbus-bootcs {
+ status = "okay";
+
+ /* Device Bus parameters are required */
+
+ /* Read parameters */
+ devbus,bus-width = <16>;
+ devbus,turn-off-ps = <60000>;
+ devbus,badr-skew-ps = <0>;
+ devbus,acc-first-ps = <124000>;
+ devbus,acc-next-ps = <248000>;
+ devbus,rd-setup-ps = <0>;
+ devbus,rd-hold-ps = <0>;
+
+ /* Write parameters */
+ devbus,sync-enable = <0>;
+ devbus,wr-high-ps = <60000>;
+ devbus,wr-low-ps = <60000>;
+ devbus,ale-wr-ps = <60000>;
+ };
+
+ internal-regs {
+ serial at 12000 {
+ status = "okay";
+ };
+ serial at 12100 {
+ status = "okay";
+ };
+
+ i2c at 11000 {
+ clock-frequency = <100000>;
+ status = "okay";
+ };
+
+ mvsdio at d4000 {
+ status = "disabled";
+ };
+
+ nand at d0000 {
+ status = "okay";
+ num-cs = <1>;
+ marvell,nand-keep-config;
+ marvell,nand-enable-arbiter;
+ nand-on-flash-bbt;
+ nand-ecc-strength = <4>;
+ nand-ecc-step-size = <512>;
+ };
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ spi-flash at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <20000000>;
+ m25p,fast-read;
+
+ partition at u-boot {
+ reg = <0x00000000 0x00100000>;
+ label = "u-boot";
+ };
+ partition at u-boot-env {
+ reg = <0x00100000 0x00040000>;
+ label = "u-boot-env";
+ };
+ partition at unused {
+ reg = <0x00140000 0x00ec0000>;
+ label = "unused";
+ };
+
+ };
+};
--
2.11.0.24.ge6920cf
^ permalink raw reply related [flat|nested] 43+ messages in thread* [PATCHv3 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards
2017-01-06 4:15 ` [PATCHv3 5/5] arm: mvebu: Add device tree for db-dxbc2 and db-xc3-24g4xg boards Chris Packham
@ 2017-01-26 15:12 ` Gregory CLEMENT
0 siblings, 0 replies; 43+ messages in thread
From: Gregory CLEMENT @ 2017-01-26 15:12 UTC (permalink / raw)
To: linux-arm-kernel
Hi Chris,
On ven., janv. 06 2017, Chris Packham <chris.packham@alliedtelesis.co.nz> wrote:
> These boards are Marvell's evaluation boards for the 98DX4251 and
> 98DX3336 SoCs.
>
> Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
> ---
> Change in v2/v3:
> - None
>
> arch/arm/boot/dts/db-dxbc2.dts | 159 ++++++++++++++++++++++++++++++++++++
> arch/arm/boot/dts/db-xc3-24g4xg.dts | 155 +++++++++++++++++++++++++++++++++++
> 2 files changed, 314 insertions(+)
> create mode 100644 arch/arm/boot/dts/db-dxbc2.dts
> create mode 100644 arch/arm/boot/dts/db-xc3-24g4xg.dts
>
> diff --git a/arch/arm/boot/dts/db-dxbc2.dts b/arch/arm/boot/dts/db-dxbc2.dts
> new file mode 100644
> index 000000000000..f56786cea5f8
> --- /dev/null
> +++ b/arch/arm/boot/dts/db-dxbc2.dts
> @@ -0,0 +1,159 @@
> +/*
> + * Device Tree file for DB-DXBC2 board
> + *
> + * Copyright (C) 2016 Allied Telesis Labs
> + *
> + * Based on armada-xp-db.dts
Since the date you base on armada-xp-db.dts, the file has changed
especially due to this series:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/468585.html
and the fix adding the missing characters in the license.
Could you update it?
Thanks
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + * Note: this Device Tree assumes that the bootloader has remapped the
> + * internal registers to 0xf1000000 (instead of the default
> + * 0xd0000000). The 0xf1000000 is the default used by the recent,
> + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
> + * boards were delivered with an older version of the bootloader that
> + * left internal registers mapped at 0xd0000000. If you are in this
> + * situation, you should either update your bootloader (preferred
> + * solution) or the below Device Tree should be adjusted.
> + */
> +
> +/dts-v1/;
> +#include "armada-xp-98dx4251.dtsi"
> +
> +/ {
> + model = "Marvell Bobcat2 Evaluation Board";
> + compatible = "marvell,db-dxbc2", "marvell,armadaxp-98dx4251", "marvell,armadaxp", "marvell,armada-370-xp";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200 earlyprintk";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0 0x00000000 0 0x20000000>; /* 512 MB */
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
> + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
> + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
> + MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
> + MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
> +
> + devbus-bootcs {
> + status = "okay";
> +
> + /* Device Bus parameters are required */
> +
> + /* Read parameters */
> + devbus,bus-width = <16>;
> + devbus,turn-off-ps = <60000>;
> + devbus,badr-skew-ps = <0>;
> + devbus,acc-first-ps = <124000>;
> + devbus,acc-next-ps = <248000>;
> + devbus,rd-setup-ps = <0>;
> + devbus,rd-hold-ps = <0>;
> +
> + /* Write parameters */
> + devbus,sync-enable = <0>;
> + devbus,wr-high-ps = <60000>;
> + devbus,wr-low-ps = <60000>;
> + devbus,ale-wr-ps = <60000>;
> + };
> +
> + internal-regs {
> + serial at 12000 {
> + status = "okay";
> + };
> + serial at 12100 {
> + status = "okay";
> + };
> +
> + i2c at 11000 {
> + clock-frequency = <100000>;
> + status = "okay";
> + };
> +
> + mvsdio at d4000 {
> + pinctrl-0 = <&sdio_pins>;
> + pinctrl-names = "default";
> + status = "okay";
> + /* No CD or WP GPIOs */
> + broken-cd;
> + };
> +
> + nand at d0000 {
> + status = "okay";
> + num-cs = <1>;
> + marvell,nand-keep-config;
> + marvell,nand-enable-arbiter;
> + nand-on-flash-bbt;
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> + };
> + };
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + spi-flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "m25p64";
> + reg = <0>; /* Chip select 0 */
> + spi-max-frequency = <20000000>;
> + m25p,fast-read;
> +
> + partition at u-boot {
> + reg = <0x00000000 0x00100000>;
> + label = "u-boot";
> + };
> + partition at u-boot-env {
> + reg = <0x00100000 0x00040000>;
> + label = "u-boot-env";
> + };
> + partition at unused {
> + reg = <0x00140000 0x00ec0000>;
> + label = "unused";
> + };
> +
> + };
> +};
> diff --git a/arch/arm/boot/dts/db-xc3-24g4xg.dts b/arch/arm/boot/dts/db-xc3-24g4xg.dts
> new file mode 100644
> index 000000000000..5eb89ffb9a7d
> --- /dev/null
> +++ b/arch/arm/boot/dts/db-xc3-24g4xg.dts
> @@ -0,0 +1,155 @@
> +/*
> + * Device Tree file for DB-XC3-24G4XG board
> + *
> + * Copyright (C) 2016 Allied Telesis Labs
> + *
> + * Based on armada-xp-db.dts
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + *
> + * Note: this Device Tree assumes that the bootloader has remapped the
> + * internal registers to 0xf1000000 (instead of the default
> + * 0xd0000000). The 0xf1000000 is the default used by the recent,
> + * DT-capable, U-Boot bootloaders provided by Marvell. Some earlier
> + * boards were delivered with an older version of the bootloader that
> + * left internal registers mapped at 0xd0000000. If you are in this
> + * situation, you should either update your bootloader (preferred
> + * solution) or the below Device Tree should be adjusted.
> + */
> +
> +/dts-v1/;
> +#include "armada-xp-98dx3336.dtsi"
> +
> +/ {
> + model = "DB-XC3-24G4XG";
> + compatible = "marvell,db-xc3-24g4xg", "marvell,armadaxp-98dx3336", "marvell,armadaxp", "marvell,armada-370-xp";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200 earlyprintk";
> + };
> +
> + memory {
> + device_type = "memory";
> + reg = <0 0x00000000 0 0x40000000>; /* 1 GB */
> + };
> +
> + soc {
> + ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xf1000000 0x100000
> + MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
> + MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x1000000
> + MBUS_ID(0x03, 0x00) 0 0 0xa8000000 0x4000000
> + MBUS_ID(0x08, 0x00) 0 0 0xac000000 0x100000>;
> +
> + devbus-bootcs {
> + status = "okay";
> +
> + /* Device Bus parameters are required */
> +
> + /* Read parameters */
> + devbus,bus-width = <16>;
> + devbus,turn-off-ps = <60000>;
> + devbus,badr-skew-ps = <0>;
> + devbus,acc-first-ps = <124000>;
> + devbus,acc-next-ps = <248000>;
> + devbus,rd-setup-ps = <0>;
> + devbus,rd-hold-ps = <0>;
> +
> + /* Write parameters */
> + devbus,sync-enable = <0>;
> + devbus,wr-high-ps = <60000>;
> + devbus,wr-low-ps = <60000>;
> + devbus,ale-wr-ps = <60000>;
> + };
> +
> + internal-regs {
> + serial at 12000 {
> + status = "okay";
> + };
> + serial at 12100 {
> + status = "okay";
> + };
> +
> + i2c at 11000 {
> + clock-frequency = <100000>;
> + status = "okay";
> + };
> +
> + mvsdio at d4000 {
> + status = "disabled";
> + };
> +
> + nand at d0000 {
> + status = "okay";
> + num-cs = <1>;
> + marvell,nand-keep-config;
> + marvell,nand-enable-arbiter;
> + nand-on-flash-bbt;
> + nand-ecc-strength = <4>;
> + nand-ecc-step-size = <512>;
> + };
> + };
> + };
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + spi-flash at 0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "m25p64";
> + reg = <0>; /* Chip select 0 */
> + spi-max-frequency = <20000000>;
> + m25p,fast-read;
> +
> + partition at u-boot {
> + reg = <0x00000000 0x00100000>;
> + label = "u-boot";
> + };
> + partition at u-boot-env {
> + reg = <0x00100000 0x00040000>;
> + label = "u-boot-env";
> + };
> + partition at unused {
> + reg = <0x00140000 0x00ec0000>;
> + label = "unused";
> + };
> +
> + };
> +};
> --
> 2.11.0.24.ge6920cf
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
^ permalink raw reply [flat|nested] 43+ messages in thread