Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
From: robh@kernel.org (Rob Herring)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 06/11] clk: sunxi-ng: Add A80 USB CCU
Date: Fri, 27 Jan 2017 15:15:59 -0600	[thread overview]
Message-ID: <20170127211559.ztsauntipyiheopu@rob-hp-laptop> (raw)
In-Reply-To: <20170124023230.3990-7-wens@csie.org>

On Tue, Jan 24, 2017 at 10:32:25AM +0800, Chen-Yu Tsai wrote:
> Add support for the USB clock controls found on the A80.
> 
> Signed-off-by: Chen-Yu Tsai <wens@csie.org>
> ---
>  .../devicetree/bindings/clock/sun9i-usb.txt        |  24 ++++
>  drivers/clk/sunxi-ng/Makefile                      |   1 +
>  drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c           | 144 +++++++++++++++++++++
>  drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.h           |  25 ++++
>  include/dt-bindings/clock/sun9i-a80-usb.h          |  59 +++++++++
>  include/dt-bindings/reset/sun9i-a80-usb.h          |  56 ++++++++
>  6 files changed, 309 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/clock/sun9i-usb.txt
>  create mode 100644 drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.c
>  create mode 100644 drivers/clk/sunxi-ng/ccu-sun9i-a80-usb.h
>  create mode 100644 include/dt-bindings/clock/sun9i-a80-usb.h
>  create mode 100644 include/dt-bindings/reset/sun9i-a80-usb.h
> 
> diff --git a/Documentation/devicetree/bindings/clock/sun9i-usb.txt b/Documentation/devicetree/bindings/clock/sun9i-usb.txt
> new file mode 100644
> index 000000000000..c2d38626eaaa
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/clock/sun9i-usb.txt
> @@ -0,0 +1,24 @@
> +Allwinner A80 USB Clock Control Binding
> +------------------------------------
> +
> +Required properties :
> +- compatible: must contain one of the following compatibles:
> +		- "allwinner,sun9i-a80-usb-clocks"
> +
> +- reg: Must contain the registers base address and length
> +- clocks: phandle to the clocks feeding the USB subsystem. Two are needed:
> +  - "bus": the bus clock for the whole USB subsystem
> +  - "hosc": the high frequency oscillator (usually at 24MHz)
> +- clock-names: Must contain the clock names described just above
> +- #clock-cells : must contain 1
> +- #reset-cells : must contain 1
> +
> +Example:
> +usb_clocks: clock at 00a08000 {

Drop leading 0s.

With that, for the binding:

Acked-by: Rob Herring <robh@kernel.org>

> +	compatible = "allwinner,sun9i-a80-usb-clks";
> +	reg = <0x00a08000 0x8>;
> +	clocks = <&ccu CLK_BUS_USB>, <&osc24M>;
> +	clock-names = "bus", "hosc";
> +	#clock-cells = <1>;
> +	#reset-cells = <1>;
> +};

  parent reply	other threads:[~2017-01-27 21:15 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-01-24  2:32 [PATCH 00/11] clk: sunxi-ng: Add support for A80 CCUs Chen-Yu Tsai
2017-01-24  2:32 ` [PATCH 01/11] clk: sunxi-ng: mux: Fix determine_rate for mux clocks with pre-dividers Chen-Yu Tsai
2017-01-26  9:55   ` Maxime Ripard
2017-01-26 11:22     ` Chen-Yu Tsai
2017-01-24  2:32 ` [PATCH 02/11] clk: sunxi-ng: mux: honor CLK_SET_RATE_NO_REPARENT flag Chen-Yu Tsai
2017-01-24  2:32 ` [PATCH 03/11] clk: sunxi-ng: mux: Get closest parent rate possible with CLK_SET_RATE_PARENT Chen-Yu Tsai
2017-01-24  2:32 ` [PATCH 04/11] clk: sunxi-ng: Support separately grouped PLL lock status register Chen-Yu Tsai
2017-01-26  9:57   ` Maxime Ripard
2017-01-24  2:32 ` [PATCH 05/11] clk: sunxi-ng: Add A80 CCU Chen-Yu Tsai
2017-01-27 21:13   ` Rob Herring
2017-01-24  2:32 ` [PATCH 06/11] clk: sunxi-ng: Add A80 USB CCU Chen-Yu Tsai
2017-01-26 10:14   ` Maxime Ripard
2017-01-26 11:12     ` [linux-sunxi] " Chen-Yu Tsai
2017-01-27  8:45       ` Maxime Ripard
2017-01-27 21:15   ` Rob Herring [this message]
2017-01-24  2:32 ` [PATCH 07/11] clk: sunxi-ng: Add A80 Display Engine CCU Chen-Yu Tsai
2017-01-26 10:39   ` Maxime Ripard
2017-01-26 11:20     ` Chen-Yu Tsai
2017-01-27  8:58       ` Maxime Ripard
2017-01-27  9:26         ` Chen-Yu Tsai
2017-01-27  9:42           ` Maxime Ripard
2017-01-24  2:32 ` [PATCH 08/11] ARM: dts: sun8i-a23-q8-tablet: Drop pinmux setting for codec PA gpio Chen-Yu Tsai
2017-01-26 10:38   ` Maxime Ripard
2017-01-26 11:15     ` Chen-Yu Tsai
2017-01-24  2:32 ` [PATCH 09/11] ARM: dts: sunxi: Remove no longer used pinctrl/sun4i-a10.h header Chen-Yu Tsai
2017-01-26 10:21   ` Maxime Ripard
2017-01-24  2:32 ` [PATCH 10/11] arm64: dts: allwinner: " Chen-Yu Tsai
2017-01-26 10:15   ` Maxime Ripard
2017-01-26 11:23     ` Chen-Yu Tsai
2017-01-27  8:46       ` Maxime Ripard
2017-01-24  2:32 ` [PATCH 11/11] ARM: dts: sun9i: Switch to new clock bindings Chen-Yu Tsai
2017-01-24  6:03 ` [linux-sunxi] [PATCH 00/11] clk: sunxi-ng: Add support for A80 CCUs Priit Laes

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170127211559.ztsauntipyiheopu@rob-hp-laptop \
    --to=robh@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox