From: lee.jones@linaro.org (Lee Jones)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 00/10] serial: st-asc: Allow handling of RTS line
Date: Fri, 3 Feb 2017 09:22:59 +0000 [thread overview]
Message-ID: <20170203092259.3opu2feqnco6gv2s@dell> (raw)
In-Reply-To: <20170202095541.GB30437@kroah.com>
On Thu, 02 Feb 2017, Greg KH wrote:
> On Thu, Feb 02, 2017 at 07:42:36AM +0000, Lee Jones wrote:
> > Hi Greg, Jiri,
> >
> > > When hardware flow-control is disabled, manual toggling of the UART's
> > > reset line (RTS) using userland applications (e.g. stty) is not
> > > possible, since the ASC IP does not provide this functionality in the
> > > same was as some other IPs do. Thus, we have to do this manually.
> > >
> > > This set ensures the correct Pinctrl groups are configured and
> > > obtained for both manual toggling of the RTS line and for the IP to
> > > take over the lines when HW flow-control is requested by the user.
> > >
> > > Lee Jones (10):
> > > serial: st-asc: Ignore the parity error bit if 8-bit mode is enabled
> > > serial: st-asc: Provide RTS functionality
> > > serial: st-asc: Read in all Pinctrl states
> > > serial: st-asc: (De)Register GPIOD and swap Pinctrl profiles
> > > serial: st-asc: Use generic DT binding for announcing RTS/CTS lines
> > > dt-bindings: serial: Update 'uart-has-rtscts' description
> > > ARM: dts: STiH410-b2260: Identify the UART RTS line
> > > ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control
> > > ARM: dts: STiH407-family: Use new Pinctrl groups
> > > ARM: dts: STiH410-b2260: Enable HW flow-control
> > >
> > > .../devicetree/bindings/serial/serial.txt | 3 +-
> > > arch/arm/boot/dts/stih407-family.dtsi | 3 +-
> > > arch/arm/boot/dts/stih407-pinctrl.dtsi | 12 ++-
> > > arch/arm/boot/dts/stih410-b2260.dts | 5 +
> > > drivers/tty/serial/st-asc.c | 101 +++++++++++++++++++--
> > > 5 files changed, 110 insertions(+), 14 deletions(-)
> >
> > Looks like everyone is happy with the set.
> >
> > Are you planning to merge it?
>
> I'll take it in my next round of patches, give me a few days to sync up,
> I normally do serial patches once a week or so.
Works for me. Thanks Greg.
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
next prev parent reply other threads:[~2017-02-03 9:22 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-01-27 17:27 [PATCH v2 00/10] serial: st-asc: Allow handling of RTS line Lee Jones
2017-01-27 17:27 ` [PATCH v2 01/10] serial: st-asc: Ignore the parity error bit if 8-bit mode is enabled Lee Jones
2017-01-27 17:27 ` [PATCH v2 02/10] serial: st-asc: Provide RTS functionality Lee Jones
2017-01-27 17:27 ` [PATCH v2 03/10] serial: st-asc: Read in all Pinctrl states Lee Jones
2017-01-27 17:27 ` [PATCH v2 04/10] serial: st-asc: (De)Register GPIOD and swap Pinctrl profiles Lee Jones
2017-01-27 17:27 ` [PATCH v2 05/10] serial: st-asc: Use generic DT binding for announcing RTS/CTS lines Lee Jones
2017-01-27 17:28 ` [PATCH v2 06/10] dt-bindings: serial: Update 'uart-has-rtscts' description Lee Jones
2017-02-01 15:41 ` Rob Herring
2017-01-27 17:28 ` [PATCH v2 07/10] ARM: dts: STiH410-b2260: Identify the UART RTS line Lee Jones
2017-01-27 17:28 ` [PATCH v2 08/10] ARM: dts: STiH407-pinctrl: Add Pinctrl group for HW flow-control Lee Jones
2017-01-27 17:28 ` [PATCH v2 09/10] ARM: dts: STiH407-family: Use new Pinctrl groups Lee Jones
2017-01-30 10:10 ` Patrice CHOTARD
2017-01-27 17:28 ` [PATCH v2 10/10] ARM: dts: STiH410-b2260: Enable HW flow-control Lee Jones
2017-02-02 7:42 ` [PATCH v2 00/10] serial: st-asc: Allow handling of RTS line Lee Jones
2017-02-02 9:55 ` Greg KH
2017-02-03 9:22 ` Lee Jones [this message]
-- strict thread matches above, loose matches on Subject: below --
2017-02-01 14:31 Lee Jones
2017-02-03 9:10 ` Greg KH
2017-02-03 10:17 ` Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170203092259.3opu2feqnco6gv2s@dell \
--to=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox