public inbox for linux-arm-kernel@lists.infradead.org
 help / color / mirror / Atom feed
From: shawnguo@kernel.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] ARM: dts: imx7d-sdb: Add thermo 2 Click Board support
Date: Thu, 16 Mar 2017 11:47:24 +0800	[thread overview]
Message-ID: <20170316034722.GB3618@dragon> (raw)
In-Reply-To: <1489596238-31669-1-git-send-email-marco.franchi@nxp.com>

On Wed, Mar 15, 2017 at 01:43:58PM -0300, Marco Franchi wrote:
> The imx7d-sdb has a mickro bus connector that can be connected to a
> Dallas Semiconductor Thermo 2 click board (DS1825 one wire temperature sensor):
> 
> https://shop.mikroe.com/click/sensors/thermo-2
> 
> Add a new device tree file to describe such hardware.
> 
> Signed-off-by: Marco Franchi <marco.franchi@nxp.com>

Instead of keeping adding new dts file for such add-on devices, please
investigate if DT overly can help.

Shawn

> ---
>  arch/arm/boot/dts/Makefile             |  1 +
>  arch/arm/boot/dts/imx7d-sdb-ds1825.dts | 60 ++++++++++++++++++++++++++++++++++
>  2 files changed, 61 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx7d-sdb-ds1825.dts
> 
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7009856..d90c6c2 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -458,6 +458,7 @@ dtb-$(CONFIG_SOC_IMX7D) += \
>  	imx7d-nitrogen7.dtb \
>  	imx7d-sbc-imx7.dtb \
>  	imx7d-sdb.dtb \
> +	imx7d-sdb-ds1825.dtb \
>  	imx7d-sdb-sht11.dtb \
>  	imx7s-colibri-eval-v3.dtb \
>  	imx7s-warp.dtb
> diff --git a/arch/arm/boot/dts/imx7d-sdb-ds1825.dts b/arch/arm/boot/dts/imx7d-sdb-ds1825.dts
> new file mode 100644
> index 0000000..bd1cd20
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx7d-sdb-ds1825.dts
> @@ -0,0 +1,60 @@
> +/*
> + * Copyright (C) 2015 Freescale Semiconductor, Inc.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +#include "imx7d-sdb.dts"
> +
> +/ {
> +	onewire_device {
> +		compatible = "w1-gpio";
> +		gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_w1>;
> +	};
> +};
> +
> +&iomuxc_lpsr {
> +	pinctrl_w1: w1grp {
> +    	fsl,pins = <
> +			MX7D_PAD_LPSR_GPIO1_IO02__GPIO1_IO2		0x14
> +		>;
> +    };
> +};
> -- 
> 2.7.4
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

      reply	other threads:[~2017-03-16  3:47 UTC|newest]

Thread overview: 2+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-03-15 16:43 [PATCH] ARM: dts: imx7d-sdb: Add thermo 2 Click Board support Marco Franchi
2017-03-16  3:47 ` Shawn Guo [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20170316034722.GB3618@dragon \
    --to=shawnguo@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox