[PATCH v2] KVM: arm/arm64: vgic-v3: De-optimize VMCR save/restore when emulating a GICv2

[cdall@linaro.org (Christoffer Dall)]

On Wed, Apr 19, 2017 at 12:15:26PM +0100, Marc Zyngier wrote:
> When emulating a GICv2-on-GICv3, special care must be taken to only
> save/restore VMCR_EL2 when ICC_SRE_EL1.SRE is cleared. Otherwise,
> all Group-0 interrupts end-up being delivered as FIQ, which is
> probably not what the guest expects, as demonstrated here with
> an unhappy EFI:
> 
> 	FIQ Exception at 0x000000013BD21CC4
> 
> This means that we cannot perform the load/put trick when dealing
> with VMCR_EL2 (because the host has SRE set), and we have to deal
> with it in the world-switch.
> 
> Fortunately, this is not the most common case (modern guests should
> be able to deal with GICv3 directly), and the performance is not worse
> than what it was before the VMCR optimization.
> 
> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>

Reviewed-by: Christoffer Dall <cdall@linaro.org>

I have applied both fixes.

Thanks,
-Christoffer

> ---
> * From v1:
>   - Move vgic_sre testing from vgic_{load,put} to vgic_v3_{load,put}
> 
>  virt/kvm/arm/hyp/vgic-v3-sr.c |  8 ++++++--
>  virt/kvm/arm/vgic/vgic-v3.c   | 11 +++++++++--
>  2 files changed, 15 insertions(+), 4 deletions(-)
> 
> diff --git a/virt/kvm/arm/hyp/vgic-v3-sr.c b/virt/kvm/arm/hyp/vgic-v3-sr.c
> index 3d0b1ddb6929..91922c1eddc8 100644
> --- a/virt/kvm/arm/hyp/vgic-v3-sr.c
> +++ b/virt/kvm/arm/hyp/vgic-v3-sr.c
> @@ -128,8 +128,10 @@ void __hyp_text __vgic_v3_save_state(struct kvm_vcpu *vcpu)
>  	 * Make sure stores to the GIC via the memory mapped interface
>  	 * are now visible to the system register interface.
>  	 */
> -	if (!cpu_if->vgic_sre)
> +	if (!cpu_if->vgic_sre) {
>  		dsb(st);
> +		cpu_if->vgic_vmcr = read_gicreg(ICH_VMCR_EL2);
> +	}
>  
>  	if (used_lrs) {
>  		int i;
> @@ -205,11 +207,13 @@ void __hyp_text __vgic_v3_restore_state(struct kvm_vcpu *vcpu)
>  	 * delivered as a FIQ to the guest, with potentially fatal
>  	 * consequences. So we must make sure that ICC_SRE_EL1 has
>  	 * been actually programmed with the value we want before
> -	 * starting to mess with the rest of the GIC.
> +	 * starting to mess with the rest of the GIC, and VMCR_EL2 in
> +	 * particular.
>  	 */
>  	if (!cpu_if->vgic_sre) {
>  		write_gicreg(0, ICC_SRE_EL1);
>  		isb();
> +		write_gicreg(cpu_if->vgic_vmcr, ICH_VMCR_EL2);
>  	}
>  
>  	val = read_gicreg(ICH_VTR_EL2);
> diff --git a/virt/kvm/arm/vgic/vgic-v3.c b/virt/kvm/arm/vgic/vgic-v3.c
> index bc7010db9f4d..df1503650300 100644
> --- a/virt/kvm/arm/vgic/vgic-v3.c
> +++ b/virt/kvm/arm/vgic/vgic-v3.c
> @@ -373,12 +373,19 @@ void vgic_v3_load(struct kvm_vcpu *vcpu)
>  {
>  	struct vgic_v3_cpu_if *cpu_if = &vcpu->arch.vgic_cpu.vgic_v3;
>  
> -	kvm_call_hyp(__vgic_v3_write_vmcr, cpu_if->vgic_vmcr);
> +	/*
> +	 * If dealing with a GICv2 emulation on GICv3, VMCR_EL2.VFIQen
> +	 * is dependent on ICC_SRE_EL1.SRE, and we have to perform the
> +	 * VMCR_EL2 save/restore in the world switch.
> +	 */
> +	if (likely(cpu_if->vgic_sre))
> +		kvm_call_hyp(__vgic_v3_write_vmcr, cpu_if->vgic_vmcr);
>  }
>  
>  void vgic_v3_put(struct kvm_vcpu *vcpu)
>  {
>  	struct vgic_v3_cpu_if *cpu_if = &vcpu->arch.vgic_cpu.vgic_v3;
>  
> -	cpu_if->vgic_vmcr = kvm_call_hyp(__vgic_v3_read_vmcr);
> +	if (likely(cpu_if->vgic_sre))
> +		cpu_if->vgic_vmcr = kvm_call_hyp(__vgic_v3_read_vmcr);
>  }
> -- 
> 2.11.0
>