From: shawnguo@kernel.org (Shawn Guo)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 3/3] arm64: dts: ls1012a: add eSDHC nodes
Date: Wed, 3 May 2017 21:05:47 +0800 [thread overview]
Message-ID: <20170503130545.GB24392@dragon> (raw)
In-Reply-To: <1492746756-12024-4-git-send-email-yangbo.lu@nxp.com>
On Fri, Apr 21, 2017 at 11:52:36AM +0800, Yangbo Lu wrote:
> There are two eSDHC controllers in LS1012A. This patch is to add
> eSDHC nodes for ls1012a dts. Also enable eSDHC for RDB/QDS boards.
>
> Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
> ---
> arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts | 8 ++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts | 13 ++++++++++++
> arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi | 25 +++++++++++++++++++++++
> 3 files changed, 46 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> index e2a93d5..a21a587 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-qds.dts
> @@ -130,3 +130,11 @@
> &sata {
> status = "okay";
> };
> +
> +&esdhc0 {
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + status = "okay";
> +};
Sort these labeled nodes alphabetically.
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> index ed77f6b..57669b0 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a-rdb.dts
> @@ -61,3 +61,16 @@
> &sata {
> status = "okay";
> };
> +
> +&esdhc0 {
> + sd-uhs-sdr104;
> + sd-uhs-sdr50;
> + sd-uhs-sdr25;
> + sd-uhs-sdr12;
> + status = "okay";
> +};
> +
> +&esdhc1 {
> + mmc-hs200-1_8v;
> + status = "okay";
> +};
Ditto
> diff --git a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> index b497ac1..e3a1943 100644
> --- a/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> +++ b/arch/arm64/boot/dts/freescale/fsl-ls1012a.dtsi
> @@ -302,6 +302,31 @@
> };
> };
>
> + esdhc0: esdhc at 1560000 {
Sort the nodes in order of unit-address.
> + compatible = "fsl,ls1012a-esdhc", "fsl,esdhc";
Please document the compatible.
Shawn
> + reg = <0x0 0x1560000 0x0 0x10000>;
> + interrupts = <0 62 0x4>;
> + clocks = <&clockgen 4 0>;
> + voltage-ranges = <1800 1800 3300 3300>;
> + sdhci,auto-cmd12;
> + big-endian;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> + esdhc1: esdhc at 1580000 {
> + compatible = "fsl,ls1012a-esdhc", "fsl,esdhc";
> + reg = <0x0 0x1580000 0x0 0x10000>;
> + interrupts = <0 65 0x4>;
> + clocks = <&clockgen 4 0>;
> + voltage-ranges = <1800 1800 3300 3300>;
> + sdhci,auto-cmd12;
> + big-endian;
> + broken-cd;
> + bus-width = <4>;
> + status = "disabled";
> + };
> +
> i2c0: i2c at 2180000 {
> compatible = "fsl,vf610-i2c";
> #address-cells = <1>;
> --
> 2.1.0.27.g96db324
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2017-05-03 13:05 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-04-21 3:52 [PATCH 0/3] Add eSDHC UHS-I/HS200 mode support for ls1012a/ls1046a/ls208xa Yangbo Lu
2017-04-21 3:52 ` [PATCH 1/3] arm64: dts: ls1046a: support SD UHS-I and eMMC HS200 on RDB Yangbo Lu
2017-05-03 12:57 ` Shawn Guo
2017-05-04 10:44 ` Y.B. Lu
2017-04-21 3:52 ` [PATCH 2/3] arm64: dts: ls208xa: support SD UHS-I on RDB and eMMC HS200 on QDS Yangbo Lu
2017-04-21 3:52 ` [PATCH 3/3] arm64: dts: ls1012a: add eSDHC nodes Yangbo Lu
2017-05-03 13:05 ` Shawn Guo [this message]
2017-05-04 10:45 ` Y.B. Lu
2017-04-24 20:17 ` [PATCH 0/3] Add eSDHC UHS-I/HS200 mode support for ls1012a/ls1046a/ls208xa Ulf Hansson
2017-04-25 9:01 ` Y.B. Lu
2017-05-03 13:17 ` Shawn Guo
2017-05-03 13:14 ` Shawn Guo
2017-05-04 10:57 ` Y.B. Lu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170503130545.GB24392@dragon \
--to=shawnguo@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox