* [PATCH V5 1/2] dt-bindings: timer: add nxp tpm timer binding doc
2017-08-01 8:40 [PATCH V5 0/2] timer: add imx tpm timer support Dong Aisheng
@ 2017-08-01 8:40 ` Dong Aisheng
2017-08-01 8:40 ` [PATCH V5 2/2] clocksource/drivers/imx-tpm: add imx tpm timer support Dong Aisheng
2017-08-01 9:32 ` [PATCH V5 0/2] timer: " Daniel Lezcano
2 siblings, 0 replies; 4+ messages in thread
From: Dong Aisheng @ 2017-08-01 8:40 UTC (permalink / raw)
To: linux-arm-kernel
Adding NXP Low Power Timer/Pulse Width Modulation Module (TPM)
binding doc.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree at vger.kernel.org
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Bai Ping <ping.bai@nxp.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
---
ChangeLog:
v1->v5:
* No changes
---
.../devicetree/bindings/timer/nxp,tpm-timer.txt | 28 ++++++++++++++++++++++
1 file changed, 28 insertions(+)
create mode 100644 Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt
diff --git a/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt
new file mode 100644
index 0000000..b4aa7dd
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/nxp,tpm-timer.txt
@@ -0,0 +1,28 @@
+NXP Low Power Timer/Pulse Width Modulation Module (TPM)
+
+The Timer/PWM Module (TPM) supports input capture, output compare,
+and the generation of PWM signals to control electric motor and power
+management applications. The counter, compare and capture registers
+are clocked by an asynchronous clock that can remain enabled in low
+power modes. TPM can support global counter bus where one TPM drives
+the counter bus for the others, provided bit width is the same.
+
+Required properties:
+
+- compatible : should be "fsl,imx7ulp-tpm"
+- reg : Specifies base physical address and size of the register sets
+ for the clock event device and clock source device.
+- interrupts : Should be the clock event device interrupt.
+- clocks : The clocks provided by the SoC to drive the timer, must contain
+ an entry for each entry in clock-names.
+- clock-names : Must include the following entries: "igp" and "per".
+
+Example:
+tpm5: tpm at 40260000 {
+ compatible = "fsl,imx7ulp-tpm";
+ reg = <0x40260000 0x1000>;
+ interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX7ULP_CLK_NIC1_BUS_DIV>,
+ <&clks IMX7ULP_CLK_LPTPM5>;
+ clock-names = "ipg", "per";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH V5 2/2] clocksource/drivers/imx-tpm: add imx tpm timer support
2017-08-01 8:40 [PATCH V5 0/2] timer: add imx tpm timer support Dong Aisheng
2017-08-01 8:40 ` [PATCH V5 1/2] dt-bindings: timer: add nxp tpm timer binding doc Dong Aisheng
@ 2017-08-01 8:40 ` Dong Aisheng
2017-08-01 9:32 ` [PATCH V5 0/2] timer: " Daniel Lezcano
2 siblings, 0 replies; 4+ messages in thread
From: Dong Aisheng @ 2017-08-01 8:40 UTC (permalink / raw)
To: linux-arm-kernel
IMX Timer/PWM Module (TPM) supports both timer and pwm function while
this patch only adds the timer support. PWM would be added later.
The TPM counter, compare and capture registers are clocked by an
asynchronous clock that can remain enabled in low power modes.
NOTE: We observed in a very small probability, the bus fabric
contention between GPU and A7 may results a few cycles delay
of writing CNT registers which may cause the min_delta event got
missed, so we need add a ETIME check here in case it happened.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Anson Huang <Anson.Huang@nxp.com>
Cc: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
---
ChangeLog:
v4->v5:
* use request_irq instead of setup_irq
* switch to TIMER_OF_DECLARE from CLOCKSOURCE_OF_DECLARE
* add more error check
* patch title change to clocksource/drivers/imx-tpm: add imx tpm timer support
v3->v4:
* also add ETIME explanation in function
v2->v3:
* address all comments from Daniel Lezcano
* add more explaination on ETIME check in commit message
v1->v2:
* change to readl/writel from __raw_readl/writel according to Arnd's
suggestion to avoid endian issue
* add help information in Kconfig
* add more error checking
---
drivers/clocksource/Kconfig | 8 ++
drivers/clocksource/Makefile | 1 +
drivers/clocksource/timer-imx-tpm.c | 239 ++++++++++++++++++++++++++++++++++++
3 files changed, 248 insertions(+)
create mode 100644 drivers/clocksource/timer-imx-tpm.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 88818a4..a4a1ff3 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -591,6 +591,14 @@ config CLKSRC_IMX_GPT
depends on ARM && CLKDEV_LOOKUP
select CLKSRC_MMIO
+config CLKSRC_IMX_TPM
+ bool "Clocksource using i.MX TPM" if COMPILE_TEST
+ depends on ARM && CLKDEV_LOOKUP && GENERIC_CLOCKEVENTS
+ select CLKSRC_MMIO
+ help
+ Enable this option to use IMX Timer/PWM Module (TPM) timer as
+ clocksource.
+
config CLKSRC_ST_LPC
bool "Low power clocksource found in the LPC" if COMPILE_TEST
select TIMER_OF if OF
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 72bfd00..1631a84 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -66,6 +66,7 @@ obj-$(CONFIG_CLKSRC_VERSATILE) += versatile.o
obj-$(CONFIG_CLKSRC_MIPS_GIC) += mips-gic-timer.o
obj-$(CONFIG_CLKSRC_TANGO_XTAL) += tango_xtal.o
obj-$(CONFIG_CLKSRC_IMX_GPT) += timer-imx-gpt.o
+obj-$(CONFIG_CLKSRC_IMX_TPM) += timer-imx-tpm.o
obj-$(CONFIG_ASM9260_TIMER) += asm9260_timer.o
obj-$(CONFIG_H8300_TMR8) += h8300_timer8.o
obj-$(CONFIG_H8300_TMR16) += h8300_timer16.o
diff --git a/drivers/clocksource/timer-imx-tpm.c b/drivers/clocksource/timer-imx-tpm.c
new file mode 100644
index 0000000..21bffdc
--- /dev/null
+++ b/drivers/clocksource/timer-imx-tpm.c
@@ -0,0 +1,239 @@
+/*
+ * Copyright 2016 Freescale Semiconductor, Inc.
+ * Copyright 2017 NXP
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/clocksource.h>
+#include <linux/delay.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/sched_clock.h>
+
+#define TPM_SC 0x10
+#define TPM_SC_CMOD_INC_PER_CNT (0x1 << 3)
+#define TPM_SC_CMOD_DIV_DEFAULT 0x3
+#define TPM_CNT 0x14
+#define TPM_MOD 0x18
+#define TPM_STATUS 0x1c
+#define TPM_STATUS_CH0F BIT(0)
+#define TPM_C0SC 0x20
+#define TPM_C0SC_CHIE BIT(6)
+#define TPM_C0SC_MODE_SHIFT 2
+#define TPM_C0SC_MODE_MASK 0x3c
+#define TPM_C0SC_MODE_SW_COMPARE 0x4
+#define TPM_C0V 0x24
+
+static void __iomem *timer_base;
+static struct clock_event_device clockevent_tpm;
+
+static inline void tpm_timer_disable(void)
+{
+ unsigned int val;
+
+ /* channel disable */
+ val = readl(timer_base + TPM_C0SC);
+ val &= ~(TPM_C0SC_MODE_MASK | TPM_C0SC_CHIE);
+ writel(val, timer_base + TPM_C0SC);
+}
+
+static inline void tpm_timer_enable(void)
+{
+ unsigned int val;
+
+ /* channel enabled in sw compare mode */
+ val = readl(timer_base + TPM_C0SC);
+ val |= (TPM_C0SC_MODE_SW_COMPARE << TPM_C0SC_MODE_SHIFT) |
+ TPM_C0SC_CHIE;
+ writel(val, timer_base + TPM_C0SC);
+}
+
+static inline void tpm_irq_acknowledge(void)
+{
+ writel(TPM_STATUS_CH0F, timer_base + TPM_STATUS);
+}
+
+static struct delay_timer tpm_delay_timer;
+
+static inline unsigned long tpm_read_counter(void)
+{
+ return readl(timer_base + TPM_CNT);
+}
+
+static unsigned long tpm_read_current_timer(void)
+{
+ return tpm_read_counter();
+}
+
+static u64 notrace tpm_read_sched_clock(void)
+{
+ return tpm_read_counter();
+}
+
+static int __init tpm_clocksource_init(unsigned long rate)
+{
+ tpm_delay_timer.read_current_timer = &tpm_read_current_timer;
+ tpm_delay_timer.freq = rate;
+ register_current_timer_delay(&tpm_delay_timer);
+
+ sched_clock_register(tpm_read_sched_clock, 32, rate);
+
+ return clocksource_mmio_init(timer_base + TPM_CNT, "imx-tpm",
+ rate, 200, 32, clocksource_mmio_readl_up);
+}
+
+static int tpm_set_next_event(unsigned long delta,
+ struct clock_event_device *evt)
+{
+ unsigned long next, now;
+
+ next = tpm_read_counter();
+ next += delta;
+ writel(next, timer_base + TPM_C0V);
+ now = tpm_read_counter();
+
+ /*
+ * NOTE: We observed in a very small probability, the bus fabric
+ * contention between GPU and A7 may results a few cycles delay
+ * of writing CNT registers which may cause the min_delta event got
+ * missed, so we need add a ETIME check here in case it happened.
+ */
+ return (int)((next - now) <= 0) ? -ETIME : 0;
+}
+
+static int tpm_set_state_oneshot(struct clock_event_device *evt)
+{
+ tpm_timer_enable();
+
+ return 0;
+}
+
+static int tpm_set_state_shutdown(struct clock_event_device *evt)
+{
+ tpm_timer_disable();
+
+ return 0;
+}
+
+static irqreturn_t tpm_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *evt = dev_id;
+
+ tpm_irq_acknowledge();
+
+ evt->event_handler(evt);
+
+ return IRQ_HANDLED;
+}
+
+static struct clock_event_device clockevent_tpm = {
+ .name = "i.MX7ULP TPM Timer",
+ .features = CLOCK_EVT_FEAT_ONESHOT,
+ .set_state_oneshot = tpm_set_state_oneshot,
+ .set_next_event = tpm_set_next_event,
+ .set_state_shutdown = tpm_set_state_shutdown,
+ .rating = 200,
+};
+
+static int __init tpm_clockevent_init(unsigned long rate, int irq)
+{
+ int ret;
+
+ ret = request_irq(irq, tpm_timer_interrupt, IRQF_TIMER | IRQF_IRQPOLL,
+ "i.MX7ULP TPM Timer", &clockevent_tpm);
+
+ clockevent_tpm.cpumask = cpumask_of(0);
+ clockevent_tpm.irq = irq;
+ clockevents_config_and_register(&clockevent_tpm,
+ rate, 300, 0xfffffffe);
+
+ return ret;
+}
+
+static int __init tpm_timer_init(struct device_node *np)
+{
+ struct clk *ipg, *per;
+ int irq, ret;
+ u32 rate;
+
+ timer_base = of_iomap(np, 0);
+ if (!timer_base) {
+ pr_err("tpm: failed to get base address\n");
+ return -ENXIO;
+ }
+
+ irq = irq_of_parse_and_map(np, 0);
+ if (!irq) {
+ pr_err("tpm: failed to get irq\n");
+ ret = -ENOENT;
+ goto err_iomap;
+ }
+
+ ipg = of_clk_get_by_name(np, "ipg");
+ per = of_clk_get_by_name(np, "per");
+ if (IS_ERR(ipg) || IS_ERR(per)) {
+ pr_err("tpm: failed to get igp or per clk\n");
+ ret = -ENODEV;
+ goto err_clk_get;
+ }
+
+ /* enable clk before accessing registers */
+ ret = clk_prepare_enable(ipg);
+ if (ret) {
+ pr_err("tpm: ipg clock enable failed (%d)\n", ret);
+ goto err_clk_get;
+ }
+
+ ret = clk_prepare_enable(per);
+ if (ret) {
+ pr_err("tpm: per clock enable failed (%d)\n", ret);
+ goto err_per_clk_enable;
+ }
+
+ /*
+ * Initialize tpm module to a known state
+ * 1) Counter disabled
+ * 2) TPM counter operates in up counting mode
+ * 3) Timer Overflow Interrupt disabled
+ * 4) Channel0 disabled
+ * 5) DMA transfers disabled
+ */
+ writel(0, timer_base + TPM_SC);
+ writel(0, timer_base + TPM_CNT);
+ writel(0, timer_base + TPM_C0SC);
+
+ /* increase per cnt, div 8 by default */
+ writel(TPM_SC_CMOD_INC_PER_CNT | TPM_SC_CMOD_DIV_DEFAULT,
+ timer_base + TPM_SC);
+
+ /* set MOD register to maximum for free running mode */
+ writel(0xffffffff, timer_base + TPM_MOD);
+
+ rate = clk_get_rate(per) >> 3;
+ ret = tpm_clocksource_init(rate);
+ if (ret)
+ goto err_per_clk_enable;
+
+ ret = tpm_clockevent_init(rate, irq);
+ if (ret)
+ goto err_per_clk_enable;
+
+ return 0;
+
+err_per_clk_enable:
+ clk_disable_unprepare(ipg);
+err_clk_get:
+ clk_put(per);
+ clk_put(ipg);
+err_iomap:
+ iounmap(timer_base);
+ return ret;
+}
+TIMER_OF_DECLARE(imx7ulp, "fsl,imx7ulp-tpm", tpm_timer_init);
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread