From: romain.izard.pro@gmail.com (Romain Izard)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 7/9] pwm: atmel-tcb: Support backup mode
Date: Fri, 15 Sep 2017 16:04:09 +0200 [thread overview]
Message-ID: <20170915140411.31716-8-romain.izard.pro@gmail.com> (raw)
In-Reply-To: <20170915140411.31716-1-romain.izard.pro@gmail.com>
Save and restore registers for the PWM on suspend and resume, which
makes hibernation and backup modes possible.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
---
drivers/pwm/pwm-atmel-tcb.c | 63 +++++++++++++++++++++++++++++++++++++++++++--
1 file changed, 61 insertions(+), 2 deletions(-)
diff --git a/drivers/pwm/pwm-atmel-tcb.c b/drivers/pwm/pwm-atmel-tcb.c
index 75db585a2a94..acd3ce8ecf3f 100644
--- a/drivers/pwm/pwm-atmel-tcb.c
+++ b/drivers/pwm/pwm-atmel-tcb.c
@@ -37,11 +37,20 @@ struct atmel_tcb_pwm_device {
unsigned period; /* PWM period expressed in clk cycles */
};
+struct atmel_tcb_channel {
+ u32 enabled;
+ u32 cmr;
+ u32 ra;
+ u32 rb;
+ u32 rc;
+};
+
struct atmel_tcb_pwm_chip {
struct pwm_chip chip;
spinlock_t lock;
struct atmel_tc *tc;
struct atmel_tcb_pwm_device *pwms[NPWM];
+ struct atmel_tcb_channel bkup[NPWM / 2];
};
static inline struct atmel_tcb_pwm_chip *to_tcb_chip(struct pwm_chip *chip)
@@ -175,12 +184,15 @@ static void atmel_tcb_pwm_disable(struct pwm_chip *chip, struct pwm_device *pwm)
* Use software trigger to apply the new setting.
* If both PWM devices in this group are disabled we stop the clock.
*/
- if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC)))
+ if (!(cmr & (ATMEL_TC_ACPC | ATMEL_TC_BCPC))) {
__raw_writel(ATMEL_TC_SWTRG | ATMEL_TC_CLKDIS,
regs + ATMEL_TC_REG(group, CCR));
- else
+ tcbpwmc->bkup[group].enabled = 1;
+ } else {
__raw_writel(ATMEL_TC_SWTRG, regs +
ATMEL_TC_REG(group, CCR));
+ tcbpwmc->bkup[group].enabled = 0;
+ }
spin_unlock(&tcbpwmc->lock);
}
@@ -263,6 +275,7 @@ static int atmel_tcb_pwm_enable(struct pwm_chip *chip, struct pwm_device *pwm)
/* Use software trigger to apply the new setting */
__raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
regs + ATMEL_TC_REG(group, CCR));
+ tcbpwmc->bkup[group].enabled = 1;
spin_unlock(&tcbpwmc->lock);
return 0;
}
@@ -445,10 +458,56 @@ static const struct of_device_id atmel_tcb_pwm_dt_ids[] = {
};
MODULE_DEVICE_TABLE(of, atmel_tcb_pwm_dt_ids);
+#ifdef CONFIG_PM_SLEEP
+static int atmel_tcb_pwm_suspend(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
+ void __iomem *base = tcbpwm->tc->regs;
+ int i;
+
+ for (i = 0; i < (NPWM / 2); i++) {
+ struct atmel_tcb_channel *chan = &tcbpwm->bkup[i];
+
+ chan->cmr = readl(base + ATMEL_TC_REG(i, CMR));
+ chan->ra = readl(base + ATMEL_TC_REG(i, RA));
+ chan->rb = readl(base + ATMEL_TC_REG(i, RB));
+ chan->rc = readl(base + ATMEL_TC_REG(i, RC));
+ }
+ return 0;
+}
+
+static int atmel_tcb_pwm_resume(struct device *dev)
+{
+ struct platform_device *pdev = to_platform_device(dev);
+ struct atmel_tcb_pwm_chip *tcbpwm = platform_get_drvdata(pdev);
+ void __iomem *base = tcbpwm->tc->regs;
+ int i;
+
+ for (i = 0; i < (NPWM / 2); i++) {
+ struct atmel_tcb_channel *chan = &tcbpwm->bkup[i];
+
+ writel(chan->cmr, base + ATMEL_TC_REG(i, CMR));
+ writel(chan->ra, base + ATMEL_TC_REG(i, RA));
+ writel(chan->rb, base + ATMEL_TC_REG(i, RB));
+ writel(chan->rc, base + ATMEL_TC_REG(i, RC));
+ if (chan->enabled) {
+ writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+ base + ATMEL_TC_REG(i, CCR));
+ }
+ }
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(atmel_tcb_pwm_pm_ops, atmel_tcb_pwm_suspend,
+ atmel_tcb_pwm_resume);
+
static struct platform_driver atmel_tcb_pwm_driver = {
.driver = {
.name = "atmel-tcb-pwm",
.of_match_table = atmel_tcb_pwm_dt_ids,
+ .pm = &atmel_tcb_pwm_pm_ops,
},
.probe = atmel_tcb_pwm_probe,
.remove = atmel_tcb_pwm_remove,
--
2.11.0
next prev parent reply other threads:[~2017-09-15 14:04 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-09-15 14:04 [PATCH v2 0/9] Various patches for SAMA5D2 backup mode Romain Izard
2017-09-15 14:04 ` [PATCH v2 1/9] clk: at91: pmc: Wait for clocks when resuming Romain Izard
2017-09-22 12:05 ` Ludovic Desroches
2017-09-22 12:13 ` Nicolas Ferre
2017-09-15 14:04 ` [PATCH v2 2/9] clk: at91: pmc: Save SCSR during suspend Romain Izard
2017-09-15 14:04 ` [PATCH v2 3/9] clk: at91: pmc: Support backup for programmable clocks Romain Izard
2017-09-22 10:31 ` Nicolas Ferre
2017-09-25 8:25 ` Romain Izard
2017-09-15 14:04 ` [PATCH v2 4/9] mtd: nand: atmel: Avoid ECC errors when leaving backup mode Romain Izard
2017-09-18 9:50 ` Boris Brezillon
2017-09-15 14:04 ` [PATCH v2 5/9] mtd: nand: atmel: Report PMECC failures as errors Romain Izard
2017-09-18 10:00 ` Boris Brezillon
2017-09-21 9:22 ` Romain Izard
2017-09-15 14:04 ` [PATCH v2 6/9] ehci-atmel: Power down during suspend is normal Romain Izard
2017-09-22 12:40 ` Nicolas Ferre
2017-09-15 14:04 ` Romain Izard [this message]
2017-09-22 12:42 ` [PATCH v2 7/9] pwm: atmel-tcb: Support backup mode Nicolas Ferre
2017-09-15 14:04 ` [PATCH v2 8/9] atmel_flexcom: " Romain Izard
2017-09-19 9:29 ` Nicolas Ferre
2017-09-19 15:25 ` Lee Jones
2017-09-20 8:30 ` Romain Izard
2017-09-20 9:18 ` Alexandre Belloni
2017-09-15 14:04 ` [PATCH v2 9/9] tty/serial: atmel: Prevent a warning on suspend Romain Izard
2017-09-19 10:19 ` Nicolas Ferre
2017-09-20 14:35 ` Richard Genoud
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170915140411.31716-8-romain.izard.pro@gmail.com \
--to=romain.izard.pro@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).