* [PATCH v3 1/3] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40
2017-10-06 6:42 [PATCH v3 0/3] Basical device tree parts for Allwinner R40 SoC Icenowy Zheng
@ 2017-10-06 6:42 ` Icenowy Zheng
2017-10-06 6:42 ` [PATCH v3 2/3] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra Icenowy Zheng
` (2 subsequent siblings)
3 siblings, 0 replies; 5+ messages in thread
From: Icenowy Zheng @ 2017-10-06 6:42 UTC (permalink / raw)
To: linux-arm-kernel
From: Chen-Yu Tsai <wens@csie.org>
The Allwinner R40 SoC is marketed as the successor to the A20 SoC.
The R40 is a smaller chip than the A20, but features the same set
of programmable pins, with a couple extra pins and some new pin
functions. The chip features 4 Cortex-A7 cores and a Mali-400 MP2
GPU. It retains most if not all features from the A20, while adding
some new features, such as MIPI DSI output, or updating various
hardware blocks, such as DE 2.0.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Dropped all max-frequency properties in MMC nodes.
Changes in v2:
- Change the MMC frequencies to conservative verified values.
- Add fallback R40 compatible for MMC.
arch/arm/boot/dts/sun8i-r40.dtsi | 396 +++++++++++++++++++++++++++++++++++++++
1 file changed, 396 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r40.dtsi
diff --git a/arch/arm/boot/dts/sun8i-r40.dtsi b/arch/arm/boot/dts/sun8i-r40.dtsi
new file mode 100644
index 000000000000..d5a6745409ae
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r40.dtsi
@@ -0,0 +1,396 @@
+/*
+ * Copyright 2017 Chen-Yu Tsai <wens@csie.org>
+ * Copyright 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/clock/sun8i-r40-ccu.h>
+#include <dt-bindings/reset/sun8i-r40-ccu.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-parent = <&gic>;
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <0>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <1>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a7";
+ device_type = "cpu";
+ reg = <3>;
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ nmi_intc: interrupt-controller at 1c00030 {
+ compatible = "allwinner,sun7i-a20-sc-nmi";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ reg = <0x01c00030 0x0c>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ mmc0: mmc at 1c0f000 {
+ compatible = "allwinner,sun8i-r40-mmc",
+ "allwinner,sun50i-a64-mmc";
+ reg = <0x01c0f000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ pinctrl-0 = <&mmc0_pins>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc at 1c10000 {
+ compatible = "allwinner,sun8i-r40-mmc",
+ "allwinner,sun50i-a64-mmc";
+ reg = <0x01c10000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc at 1c11000 {
+ compatible = "allwinner,sun8i-r40-emmc",
+ "allwinner,sun50i-a64-emmc";
+ reg = <0x01c11000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ pinctrl-0 = <&mmc2_pins>;
+ pinctrl-names = "default";
+ interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc3: mmc at 1c12000 {
+ compatible = "allwinner,sun8i-r40-mmc",
+ "allwinner,sun50i-a64-mmc";
+ reg = <0x01c12000 0x1000>;
+ clocks = <&ccu CLK_BUS_MMC3>, <&ccu CLK_MMC3>;
+ clock-names = "ahb", "mmc";
+ resets = <&ccu RST_BUS_MMC3>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ccu: clock at 1c20000 {
+ compatible = "allwinner,sun8i-r40-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl at 1c20800 {
+ compatible = "allwinner,sun8i-r40-pinctrl";
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ #gpio-cells = <3>;
+
+ i2c0_pins: i2c0-pins {
+ pins = "PB0", "PB1";
+ function = "i2c0";
+ };
+
+ mmc0_pins: mmc0-pins {
+ pins = "PF0", "PF1", "PF2",
+ "PF3", "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc1_pg_pins: mmc1-pg-pins {
+ pins = "PG0", "PG1", "PG2",
+ "PG3", "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_pins: mmc2-pins {
+ pins = "PC5", "PC6", "PC7", "PC8", "PC9",
+ "PC10", "PC11", "PC12", "PC13", "PC14",
+ "PC15", "PC24";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ uart0_pb_pins: uart0-pb-pins {
+ pins = "PB22", "PB23";
+ function = "uart0";
+ };
+ };
+
+ uart0: serial at 1c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ status = "disabled";
+ };
+
+ uart1: serial at 1c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ status = "disabled";
+ };
+
+ uart2: serial at 1c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ status = "disabled";
+ };
+
+ uart3: serial at 1c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ status = "disabled";
+ };
+
+ uart4: serial at 1c29000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29000 0x400>;
+ interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART4>;
+ resets = <&ccu RST_BUS_UART4>;
+ status = "disabled";
+ };
+
+ uart5: serial at 1c29400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29400 0x400>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART5>;
+ resets = <&ccu RST_BUS_UART5>;
+ status = "disabled";
+ };
+
+ uart6: serial at 1c29800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29800 0x400>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART6>;
+ resets = <&ccu RST_BUS_UART6>;
+ status = "disabled";
+ };
+
+ uart7: serial at 1c29c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c29c00 0x400>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART7>;
+ resets = <&ccu RST_BUS_UART7>;
+ status = "disabled";
+ };
+
+ i2c0: i2c at 1c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c at 1c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c at 1c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b400 0x400>;
+ interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c3: i2c at 1c2b800 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b800 0x400>;
+ interrupts = <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C3>;
+ resets = <&ccu RST_BUS_I2C3>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c4: i2c at 1c2c000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2c000 0x400>;
+ interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C4>;
+ resets = <&ccu RST_BUS_I2C4>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ gic: interrupt-controller at 1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x1000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+ };
+
+ timer {
+ compatible = "arm,armv7-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+};
--
2.13.6
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v3 2/3] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra
2017-10-06 6:42 [PATCH v3 0/3] Basical device tree parts for Allwinner R40 SoC Icenowy Zheng
2017-10-06 6:42 ` [PATCH v3 1/3] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40 Icenowy Zheng
@ 2017-10-06 6:42 ` Icenowy Zheng
2017-10-06 6:42 ` [PATCH v3 3/3] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry Icenowy Zheng
2017-10-06 8:19 ` [PATCH v3 0/3] Basical device tree parts for Allwinner R40 SoC Maxime Ripard
3 siblings, 0 replies; 5+ messages in thread
From: Icenowy Zheng @ 2017-10-06 6:42 UTC (permalink / raw)
To: linux-arm-kernel
From: Chen-Yu Tsai <wens@csie.org>
The Banana Pi M2 Ultra is an SBC based on the Allwinner R40 SoC. The
form factor and position of various connectors, leds and buttons is
similar to the Banana Pi M1+, Banana Pi M3, and is exactly the same
as the latest Banana Pi M64.
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 2 GB DDR3 DRAM
- 8 GB eMMC
- micro SD card slot
- DC power jack
- HDMI output
- MIPI DSI connector
- 2x USB 2.0 hosts
- 1x USB 2.0 OTG
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 chip, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- consumer IR receiver
- audio out headphone jack
- onboard microphone
- red, green, and blue LEDs
- debug UART pins
- Li-Po battery connector
- Raspberry Pi B+ compatible GPIO header
- power, reset, and boot control buttons
This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v3:
- Added 3.3V vqmmc regulator for mmc2 (eMMC).
Changes in v2:
- Dropped the vcc5v0 regulator, as it's not used yet.
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts | 178 ++++++++++++++++++++++
2 files changed, 179 insertions(+)
create mode 100644 arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9cf688d404b8..93b1e63a52af 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -939,6 +939,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-h3-orangepi-plus2e.dtb \
sun8i-r16-bananapi-m2m.dtb \
sun8i-r16-parrot.dtb \
+ sun8i-r40-bananapi-m2-ultra.dtb \
sun8i-v3s-licheepi-zero.dtb \
sun8i-v3s-licheepi-zero-dock.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
diff --git a/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
new file mode 100644
index 000000000000..7b52608cebe6
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-r40-bananapi-m2-ultra.dts
@@ -0,0 +1,178 @@
+/*
+ * Copyright (C) 2017 Chen-Yu Tsai <wens@csie.org>
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-r40.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Banana Pi BPI-M2-Ultra";
+ compatible = "sinovoip,bpi-m2-ultra", "allwinner,sun8i-r40";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ label = "bananapi:red:pwr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ user-led-green {
+ label = "bananapi:green:user";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+
+ user-led-blue {
+ label = "bananapi:blue:user";
+ gpios = <&pio 7 22 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp22x: pmic at 34 {
+ compatible = "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pg_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&mmc2 {
+ vmmc-supply = <®_dcdc1>;
+ vqmmc-supply = <®_dcdc1>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
--
2.13.6
^ permalink raw reply related [flat|nested] 5+ messages in thread* [PATCH v3 3/3] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Berry
2017-10-06 6:42 [PATCH v3 0/3] Basical device tree parts for Allwinner R40 SoC Icenowy Zheng
2017-10-06 6:42 ` [PATCH v3 1/3] ARM: dts: sun8i: Add basic dtsi file for Allwinner R40 Icenowy Zheng
2017-10-06 6:42 ` [PATCH v3 2/3] ARM: dts: sun8i: Add board dts file for Banana Pi M2 Ultra Icenowy Zheng
@ 2017-10-06 6:42 ` Icenowy Zheng
2017-10-06 8:19 ` [PATCH v3 0/3] Basical device tree parts for Allwinner R40 SoC Maxime Ripard
3 siblings, 0 replies; 5+ messages in thread
From: Icenowy Zheng @ 2017-10-06 6:42 UTC (permalink / raw)
To: linux-arm-kernel
The Banana Pi M2 Ultra is an SBC based on the Allwinner V40 SoC (same as
the R40 SoC). The form factor is similar to the Raspberry Pi series.
It features:
- X-Powers AXP221s PMIC connected to i2c0
- 1GiB DDR3 DRAM
- microSD slot
- MicroUSB Type-B port for power and connected to usb0
- HDMI output
- MIPI DSI connector
- 4 USB Type-A ports (connected to the usb1 controller via a hub)
- gigabit ethernet with Realtek RTL8211E transceiver
- WiFi/Bluetooth with AP6212 module, with external antenna connector
- SATA and power connectors for native SATA support
- camera sensor connector
- audio out headphone jack
- red and green LEDs
- debug UART pins
- Raspberry Pi B+ compatible GPIO header
- power and reset buttons
This patch adds a dts file that enables UART, MMC and PMIC support.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
---
Changes in v2:
- Dropped the vcc5v0 regulator, as it's not used yet.
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts | 164 ++++++++++++++++++++++
2 files changed, 166 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 93b1e63a52af..da3f87b35059 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -941,7 +941,8 @@ dtb-$(CONFIG_MACH_SUN8I) += \
sun8i-r16-parrot.dtb \
sun8i-r40-bananapi-m2-ultra.dtb \
sun8i-v3s-licheepi-zero.dtb \
- sun8i-v3s-licheepi-zero-dock.dtb
+ sun8i-v3s-licheepi-zero-dock.dtb \
+ sun8i-v40-bananapi-m2-berry.dtb
dtb-$(CONFIG_MACH_SUN9I) += \
sun9i-a80-optimus.dtb \
sun9i-a80-cubieboard4.dtb
diff --git a/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
new file mode 100644
index 000000000000..8a69be2a0842
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-v40-bananapi-m2-berry.dts
@@ -0,0 +1,164 @@
+/*
+ * Copyright (C) 2017 Icenowy Zheng <icenowy@aosc.io>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-r40.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Banana Pi M2 Berry";
+ compatible = "sinovoip,bpi-m2-berry", "allwinner,sun8i-r40";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pwr-led {
+ label = "bananapi:red:pwr";
+ gpios = <&pio 7 20 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ user-led {
+ label = "bananapi:green:user";
+ gpios = <&pio 7 21 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ wifi_pwrseq: wifi_pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ reset-gpios = <&pio 6 10 GPIO_ACTIVE_LOW>; /* PG10 WIFI_EN */
+ };
+};
+
+&i2c0 {
+ status = "okay";
+
+ axp22x: pmic at 68 {
+ compatible = "x-powers,axp221";
+ reg = <0x34>;
+ interrupt-parent = <&nmi_intc>;
+ interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
+ };
+};
+
+#include "axp22x.dtsi"
+
+®_aldo3 {
+ regulator-always-on;
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "avcc";
+};
+
+®_dcdc1 {
+ regulator-always-on;
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-name = "vcc-3v0";
+};
+
+®_dcdc2 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-cpu";
+};
+
+®_dcdc3 {
+ regulator-always-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-name = "vdd-sys";
+};
+
+®_dcdc5 {
+ regulator-always-on;
+ regulator-min-microvolt = <1500000>;
+ regulator-max-microvolt = <1500000>;
+ regulator-name = "vcc-dram";
+};
+
+®_dldo1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi-io";
+};
+
+®_dldo2 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc-wifi";
+};
+
+&mmc0 {
+ vmmc-supply = <®_dcdc1>;
+ bus-width = <4>;
+ cd-gpios = <&pio 7 13 GPIO_ACTIVE_HIGH>; /* PH13 */
+ cd-inverted;
+ status = "okay";
+};
+
+&mmc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc1_pg_pins>;
+ vmmc-supply = <®_dldo2>;
+ vqmmc-supply = <®_dldo1>;
+ mmc-pwrseq = <&wifi_pwrseq>;
+ bus-width = <4>;
+ non-removable;
+ status = "okay";
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pb_pins>;
+ status = "okay";
+};
--
2.13.6
^ permalink raw reply related [flat|nested] 5+ messages in thread