public inbox for linux-arm-kernel@lists.infradead.org
 help / color / mirror / Atom feed
From: baruch@tkos.co.il (Baruch Siach)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 04/11] thermal: armada: Rationalize register accesses
Date: Mon, 18 Dec 2017 00:02:35 +0200	[thread overview]
Message-ID: <20171217220235.4uwy4nw77gf3kvfp@tarshish> (raw)
In-Reply-To: <20171216221838.v6gtaoqy2xhozapp@tarshish>

Hi Miqu?l,

On Sun, Dec 17, 2017 at 12:18:38AM +0200, Baruch Siach wrote:
> On Thu, Dec 14, 2017 at 11:30:04AM +0100, Miquel Raynal wrote:
> > Bindings were incomplete for a long time by only exposing one of the two
> > available control registers. To ease the migration to the full bindings
> > (already in use for the Armada 375 SoC), rename the pointers for
> > clarification. This way, it will only be needed to add another pointer
> > to access the other control register when the time comes.
> > 
> > This avoids dangerous situations where the offset 0 of the control
> > area can be either one register or the other depending on the bindings
> > used. After this change, device trees of other SoCs could be migrated to
> > the "full" bindings if they may benefit from features from the
> > unaccessible register, without any change in the driver.
> > 
> > Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
> > ---
> 
> [...]
> 
> > +	/*
> > +	 * Legacy DT bindings only described "control1" register (also referred
> > +	 * as "control MSB" on old documentation). New bindings cover
> > +	 * "control0/control LSB" and "control1/control MSB" registers within
> > +	 * the same resource, which is then of size 8 instead of 4.
> > +	 */
> > +	if ((res->end - res->start) == LEGACY_CONTROL_MEM_LEN) {
> > +		/* ->control0 unavailable in this configuration */
> > +		priv->control1 = control + LEGACY_CONTROL1_OFFSET;
> > +	} else {
> > +		priv->control0 = control + CONTROL0_OFFSET;
> > +		priv->control1 = control + CONTROL1_OFFSET;
> > +	}
> 
> I think we need to add a check here that the control registers area size 
> matches the expected value given the compatible string. In case of mismatch 
> probe should fail.

One more thing. You should probably use resource_size() instead of open coding 
it. resource_size() does "res->end - res->start + 1". Are you sure your code 
is correct?

> >  	priv->data = (struct armada_thermal_data *)match->data;
> >  	priv->data->init_sensor(pdev, priv);

baruch

-- 
     http://baruch.siach.name/blog/                  ~. .~   Tk Open Systems
=}------------------------------------------------ooO--U--Ooo------------{=
   - baruch at tkos.co.il - tel: +972.52.368.4656, http://www.tkos.co.il -

  reply	other threads:[~2017-12-17 22:02 UTC|newest]

Thread overview: 45+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-12-14 10:30 [PATCH v3 00/11] Armada thermal: improvements and A7K/A8K SoCs support Miquel Raynal
2017-12-14 10:30 ` [PATCH v3 01/11] dt-bindings: thermal: Describe Armada AP806 and CP110 Miquel Raynal
2017-12-15  8:27   ` Baruch Siach
2017-12-15  8:32     ` Miquel RAYNAL
2017-12-15  8:44       ` Baruch Siach
2017-12-15  8:44       ` Gregory CLEMENT
2017-12-15 10:52         ` Miquel RAYNAL
2017-12-15 23:28           ` Rob Herring
2017-12-16 12:50             ` Miquel RAYNAL
2017-12-14 10:30 ` [PATCH v3 02/11] thermal: armada: Use msleep for long delays Miquel Raynal
2017-12-14 10:51   ` Gregory CLEMENT
2017-12-14 10:30 ` [PATCH v3 03/11] thermal: armada: Simplify the check of the validity bit Miquel Raynal
2017-12-14 10:52   ` Gregory CLEMENT
2017-12-15  8:33   ` Baruch Siach
2017-12-15 10:56     ` Miquel RAYNAL
2017-12-14 10:30 ` [PATCH v3 04/11] thermal: armada: Rationalize register accesses Miquel Raynal
2017-12-14 10:55   ` Gregory CLEMENT
2017-12-15  8:56   ` Baruch Siach
2017-12-18 13:48     ` Miquel RAYNAL
2017-12-16 22:18   ` Baruch Siach
2017-12-17 22:02     ` Baruch Siach [this message]
2017-12-18 12:37       ` Miquel RAYNAL
2017-12-14 10:30 ` [PATCH v3 05/11] thermal: armada: Add support for Armada AP806 Miquel Raynal
2017-12-14 11:05   ` Gregory CLEMENT
2017-12-18  9:41     ` Miquel RAYNAL
2017-12-18 11:11       ` Baruch Siach
2017-12-18 12:25         ` Miquel RAYNAL
2017-12-16 22:22   ` Baruch Siach
2017-12-14 10:30 ` [PATCH v3 06/11] thermal: armada: Add support for Armada CP110 Miquel Raynal
2017-12-14 11:11   ` Gregory CLEMENT
2017-12-14 11:33     ` Miquel RAYNAL
2017-12-14 11:37       ` Gregory CLEMENT
2017-12-14 12:24         ` Miquel RAYNAL
2017-12-14 10:30 ` [PATCH v3 07/11] thermal: armada: Update Kconfig and module description Miquel Raynal
2017-12-14 11:13   ` Gregory CLEMENT
2017-12-14 11:17     ` Miquel RAYNAL
2017-12-14 11:30       ` Gregory CLEMENT
2017-12-14 11:36         ` Miquel RAYNAL
2017-12-14 13:10         ` Thomas Petazzoni
2017-12-14 10:30 ` [PATCH v3 08/11] thermal: armada: Change sensors trim default value Miquel Raynal
2017-12-14 10:30 ` [PATCH v3 09/11] thermal: armada: Wait sensors validity before exiting the init callback Miquel Raynal
2017-12-14 11:23   ` Gregory CLEMENT
2017-12-14 11:27     ` Miquel RAYNAL
2017-12-14 10:30 ` [PATCH v3 10/11] thermal: armada: Give useful names to the thermal zone Miquel Raynal
2017-12-14 10:30 ` [PATCH v3 11/11] ARM64: dts: marvell: Add thermal support for A7K/A8K Miquel Raynal

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20171217220235.4uwy4nw77gf3kvfp@tarshish \
    --to=baruch@tkos.co.il \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox