[PATCH v3 1/6] ARM: dts: imx6: Add initial support for phyCORE-i.MX 6 SOM

[shawnguo@kernel.org (Shawn Guo)]

On Fri, Dec 22, 2017 at 11:59:08AM +0100, Stefan Riedmueller wrote:
> This patch adds basic support for PHYTEC phyCORE-i.MX 6 SOM with i.MX
> 6Quad/Dual or i.MX 6DualLight/Solo.
> 
> Signed-off-by: Christian Hemp <c.hemp@phytec.de>
> Signed-off-by: Stefan Christ <s.christ@phytec.de>
> Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
> Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
> ---
>  arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi | 282 ++++++++++++++++++++++
>  1 file changed, 282 insertions(+)
>  create mode 100644 arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
> new file mode 100644
> index 0000000..8501ac6
> --- /dev/null
> +++ b/arch/arm/boot/dts/imx6qdl-phytec-phycore-som.dtsi
> @@ -0,0 +1,282 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Copyright (C) 2017 PHYTEC Messtechnik GmbH
> + * Author: Christian Hemp <c.hemp@phytec.de>
> + */
> +
> +#include <dt-bindings/gpio/gpio.h>
> +
> +/ {
> +	model = "PHYTEC phyCORE-i.MX 6";
> +	compatible = "phytec,imx6qdl-pcm058", "fsl,imx6qdl";
> +
> +	aliases {
> +		rtc1 = &da9062_rtc;
> +		rtc2 = &snvs_rtc;
> +	};
> +
> +	/*
> +	 * Set the minimum memory size here and
> +	 * let the bootloader set the real size.
> +	 */
> +	memory at 10000000 {
> +		device_type = "memory";
> +		reg = <0x10000000 0x8000000>;
> +	};
> +
> +	gpio_leds_som: somleds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_gpioleds_som>;
> +
> +		som_green {

We generally use hyphen rather than underscore in node name.  Also I
would suggest to have 'led' in the name to tell what the device is,
maybe 'led-green'?

> +			label = "phycore:green";
> +			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +	};
> +};
> +
> +&ecspi1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_ecspi1>;
> +	cs-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>;
> +	status = "okay";
> +
> +	flash: flash at 0 {

While it's all good to name the node in a general way, the label can be 
specific, like:

	m25p80: flash at 0 {
		...
	}

Even better, if the label is not really needed, just drop it.

> +		compatible = "m25p80";
> +		spi-max-frequency = <20000000>;
> +		reg = <0>;
> +		status = "disabled";
> +	};
> +};
> +
> +&fec {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enet>;
> +	phy-handle = <&ethphy>;
> +	phy-mode = "rgmii";
> +	phy-supply = <&vdd_eth_io>;
> +	phy-reset-gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
> +	status = "disabled";
> +
> +	mdio {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		ethphy: ethernet-phy at 3 {
> +			reg = <3>;
> +			txc-skew-ps = <1680>;
> +			rxc-skew-ps = <1860>;
> +		};
> +	};
> +};
> +
> +&gpmi {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_gpmi_nand>;
> +	nand-on-flash-bbt;
> +	status = "disabled";
> +};
> +
> +&i2c3 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_i2c3>;
> +	clock-frequency = <400000>;
> +	status = "okay";
> +
> +	eeprom: eeprom at 50 {

Is the label used at all?

> +		compatible = "atmel,24c32";
> +		reg = <0x50>;
> +	};
> +
> +	pmic0: pmic at 58 {

Ditto

> +		compatible = "dlg,da9062";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&pinctrl_pmic>;
> +		reg = <0x58>;
> +		interrupt-parent = <&gpio1>;
> +		interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
> +		interrupt-controller;
> +
> +		da9062_rtc: rtc {
> +			compatible = "dlg,da9062-rtc";
> +		};
> +
> +		da9062_wdt: watchdog {

Ditto

> +			compatible = "dlg,da9062-watchdog";
> +		};
> +
> +		da9062_reg: regulators {

Ditto

Shawn

> +			vdd_arm: buck1 {
> +				regulator-name = "vdd_arm";
> +				regulator-min-microvolt = <730000>;
> +				regulator-max-microvolt = <1380000>;
> +				regulator-always-on;
> +			};
> +
> +			vdd_soc: buck2 {
> +				regulator-name = "vdd_soc";
> +				regulator-min-microvolt = <730000>;
> +				regulator-max-microvolt = <1380000>;
> +				regulator-always-on;
> +			};
> +
> +			vdd_ddr3_1p5: buck3 {
> +				regulator-name = "vdd_ddr3";
> +				regulator-min-microvolt = <1500000>;
> +				regulator-max-microvolt = <1500000>;
> +				regulator-always-on;
> +			};
> +
> +			vdd_eth_1p2: buck4 {
> +				regulator-name = "vdd_eth";
> +				regulator-min-microvolt = <1200000>;
> +				regulator-max-microvolt = <1200000>;
> +				regulator-always-on;
> +			};
> +
> +			vdd_snvs: ldo1 {
> +				regulator-name = "vdd_snvs";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-always-on;
> +			};
> +
> +			vdd_high: ldo2 {
> +				regulator-name = "vdd_high";
> +				regulator-min-microvolt = <3000000>;
> +				regulator-max-microvolt = <3000000>;
> +				regulator-always-on;
> +			};
> +
> +			vdd_eth_io: ldo3 {
> +				regulator-name = "vdd_eth_io";
> +				regulator-min-microvolt = <2500000>;
> +				regulator-max-microvolt = <2500000>;
> +			};
> +
> +			vdd_emmc_1p8: ldo4 {
> +				regulator-name = "vdd_emmc";
> +				regulator-min-microvolt = <1800000>;
> +				regulator-max-microvolt = <1800000>;
> +			};
> +		};
> +	};
> +};
> +
> +&reg_arm {
> +	vin-supply = <&vdd_arm>;
> +};
> +
> +&reg_pu {
> +	vin-supply = <&vdd_soc>;
> +};
> +
> +&reg_soc {
> +	vin-supply = <&vdd_soc>;
> +};
> +
> +&snvs_poweroff {
> +	status = "okay";
> +};
> +
> +&usdhc4 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_usdhc4>;
> +	bus-width = <8>;
> +	non-removable;
> +	vmmc-supply = <&vdd_emmc_1p8>;
> +	status = "disabled";
> +};
> +
> +&iomuxc {
> +	pinctrl_enet: enetgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b0b0
> +			MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
> +			MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b0b0
> +			MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b0b0
> +			MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b0b0
> +			MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x1b0b0
> +			MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b0b0
> +			MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b0b0
> +			MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b0b0
> +			MX6QDL_PAD_ENET_TX_EN__ENET_TX_EN	0x1b0b0
> +			MX6QDL_PAD_SD2_DAT1__GPIO1_IO14		0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_gpioleds_som: gpioledssomgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_GPIO_4__GPIO1_IO04		0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_gpmi_nand: gpminandgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_NANDF_CLE__NAND_CLE		0xb0b1
> +			MX6QDL_PAD_NANDF_ALE__NAND_ALE		0xb0b1
> +			MX6QDL_PAD_NANDF_WP_B__NAND_WP_B	0xb0b1
> +			MX6QDL_PAD_NANDF_RB0__NAND_READY_B	0xb000
> +			MX6QDL_PAD_NANDF_CS0__NAND_CE0_B	0xb0b1
> +			MX6QDL_PAD_NANDF_CS1__NAND_CE1_B	0xb0b1
> +			MX6QDL_PAD_NANDF_CS2__NAND_CE2_B	0xb0b1
> +			MX6QDL_PAD_NANDF_CS3__NAND_CE3_B	0xb0b1
> +			MX6QDL_PAD_SD4_CMD__NAND_RE_B		0xb0b1
> +			MX6QDL_PAD_SD4_CLK__NAND_WE_B		0xb0b1
> +			MX6QDL_PAD_NANDF_D0__NAND_DATA00	0xb0b1
> +			MX6QDL_PAD_NANDF_D1__NAND_DATA01	0xb0b1
> +			MX6QDL_PAD_NANDF_D2__NAND_DATA02	0xb0b1
> +			MX6QDL_PAD_NANDF_D3__NAND_DATA03	0xb0b1
> +			MX6QDL_PAD_NANDF_D4__NAND_DATA04	0xb0b1
> +			MX6QDL_PAD_NANDF_D5__NAND_DATA05	0xb0b1
> +			MX6QDL_PAD_NANDF_D6__NAND_DATA06	0xb0b1
> +			MX6QDL_PAD_NANDF_D7__NAND_DATA07	0xb0b1
> +			MX6QDL_PAD_SD4_DAT0__NAND_DQS		0x00b1
> +		>;
> +	};
> +
> +	pinctrl_i2c3: i2c3grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_GPIO_6__I2C3_SDA		0x4001b8b1
> +			MX6QDL_PAD_GPIO_5__I2C3_SCL		0x4001b8b1
> +		>;
> +	};
> +
> +	pinctrl_ecspi1: ecspi1grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_EIM_D16__ECSPI1_SCLK		0x100b1
> +			MX6QDL_PAD_EIM_D17__ECSPI1_MISO		0x100b1
> +			MX6QDL_PAD_EIM_D18__ECSPI1_MOSI		0x100b1
> +			MX6QDL_PAD_EIM_D19__GPIO3_IO19		0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_pmic: pmicgrp {
> +		fsl,pins = <
> +			MX6QDL_PAD_GPIO_2__GPIO1_IO02		0x1b0b0
> +		>;
> +	};
> +
> +	pinctrl_usdhc4: usdhc4grp {
> +		fsl,pins = <
> +			MX6QDL_PAD_SD4_CMD__SD4_CMD		0x17059
> +			MX6QDL_PAD_SD4_CLK__SD4_CLK		0x10059
> +			MX6QDL_PAD_SD4_DAT0__SD4_DATA0		0x17059
> +			MX6QDL_PAD_SD4_DAT1__SD4_DATA1		0x17059
> +			MX6QDL_PAD_SD4_DAT2__SD4_DATA2		0x17059
> +			MX6QDL_PAD_SD4_DAT3__SD4_DATA3		0x17059
> +			MX6QDL_PAD_SD4_DAT4__SD4_DATA4		0x17059
> +			MX6QDL_PAD_SD4_DAT5__SD4_DATA5		0x17059
> +			MX6QDL_PAD_SD4_DAT6__SD4_DATA6		0x17059
> +			MX6QDL_PAD_SD4_DAT7__SD4_DATA7		0x17059
> +		>;
> +	};
> +};
> -- 
> 2.7.4
>