From: embed3d@gmail.com (Philipp Rossak)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 13/16] arm: dts: sun8i: h3: add thermal zone to H3
Date: Mon, 29 Jan 2018 00:29:16 +0100 [thread overview]
Message-ID: <20180128232919.12639-14-embed3d@gmail.com> (raw)
In-Reply-To: <20180128232919.12639-1-embed3d@gmail.com>
This patch adds the thermal zones to the H3. We have only one sensor and
that is placed in the cpu.
Signed-off-by: Philipp Rossak <embed3d@gmail.com>
---
arch/arm/boot/dts/sun8i-h3.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index fbb007e5798e..3f83f6a27c74 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -72,6 +72,15 @@
};
};
+ thermal-zones {
+ cpu-thermal {
+ /* milliseconds */
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&ths 0>;
+ };
+ };
+
timer {
compatible = "arm,armv7-timer";
interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
--
2.11.0
next prev parent reply other threads:[~2018-01-28 23:29 UTC|newest]
Thread overview: 56+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-01-28 23:29 [PATCH v2 00/16] IIO-based thermal sensor driver for Allwinner H3 and A83T SoC Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 01/16] dt-bindings: update the Allwinner GPADC device tree binding for H3 & A83T Philipp Rossak
2018-01-29 9:19 ` Maxime Ripard
2018-01-29 12:30 ` Philipp Rossak
2018-01-31 17:40 ` Quentin Schulz
2018-01-31 18:14 ` Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 02/16] arm: config: sunxi_defconfig: enable SUN4I_GPADC Philipp Rossak
2018-01-29 9:21 ` Maxime Ripard
2018-01-28 23:29 ` [PATCH v2 03/16] iio: adc: sun4i-gpadc-iio: rename A33-specified registers to contain A33 Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 04/16] iio: adc: sun4i-gpadc-iio: rework: sampling start/end code readout reg Philipp Rossak
2018-01-29 9:27 ` Maxime Ripard
2018-01-31 17:51 ` Quentin Schulz
2018-01-31 18:35 ` Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 05/16] iio: adc: sun4i-gpadc-iio: rework: support clocks and reset Philipp Rossak
2018-01-29 9:31 ` Maxime Ripard
2018-01-28 23:29 ` [PATCH v2 06/16] iio: adc: sun4i-gpadc-iio: rework: support multiple sensors Philipp Rossak
2018-01-29 9:37 ` Maxime Ripard
2018-01-31 18:42 ` Quentin Schulz
2018-02-02 14:13 ` Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 07/16] iio: adc: sun4i-gpadc-iio: rework: support nvmem calibration data Philipp Rossak
2018-01-29 9:40 ` Maxime Ripard
2018-01-29 12:33 ` Philipp Rossak
2018-01-30 8:36 ` Maxime Ripard
2018-02-02 15:24 ` Philipp Rossak
2018-01-31 22:49 ` kbuild test robot
2018-01-28 23:29 ` [PATCH v2 08/16] iio: adc: sun4i-gpadc-iio: rework: add interrupt support Philipp Rossak
2018-01-31 19:07 ` Quentin Schulz
2018-02-02 14:30 ` Philipp Rossak
2018-01-31 21:47 ` kbuild test robot
2018-01-28 23:29 ` [PATCH v2 09/16] iio: adc: sun4i-gpadc-iio: add support for H3 thermal sensor Philipp Rossak
2018-01-29 9:46 ` Maxime Ripard
2018-01-31 19:23 ` Quentin Schulz
2018-02-02 14:42 ` Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 10/16] iio: adc: sun4i-gpadc-iio: add support for A83T " Philipp Rossak
2018-01-29 9:48 ` Maxime Ripard
2018-01-29 11:53 ` Philipp Rossak
2018-01-30 8:32 ` Maxime Ripard
2018-01-28 23:29 ` [PATCH v2 11/16] arm: dts: sunxi-h3-h5: add support for the thermal sensor in H3 and H5 Philipp Rossak
2018-01-29 9:49 ` Maxime Ripard
2018-01-29 11:54 ` Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 12/16] arm: dts: sun8i: h3: add support for the thermal sensor in H3 Philipp Rossak
2018-01-28 23:29 ` Philipp Rossak [this message]
2018-01-29 9:50 ` [PATCH v2 13/16] arm: dts: sun8i: h3: add thermal zone to H3 Maxime Ripard
2018-01-29 11:56 ` Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 14/16] arm: dts: sun8i: h3: enable H3 sid controller Philipp Rossak
2018-01-29 9:52 ` Maxime Ripard
2018-01-29 12:03 ` Philipp Rossak
2018-04-19 15:11 ` [linux-sunxi] " Kyle Evans
2018-04-19 15:13 ` Icenowy Zheng
2018-04-19 15:19 ` Kyle Evans
2018-04-20 9:35 ` Philipp Rossak
2018-07-24 17:19 ` Paul Kocialkowski
2018-07-25 9:05 ` Emmanuel Vadot
2018-07-25 9:12 ` Paul Kocialkowski
2018-01-28 23:29 ` [PATCH v2 15/16] arm: dts: sun8i: a83t: add support for the thermal sensor in A83T Philipp Rossak
2018-01-28 23:29 ` [PATCH v2 16/16] arm: dts: sun8i: a83t: add thermal zone to A83T Philipp Rossak
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180128232919.12639-14-embed3d@gmail.com \
--to=embed3d@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).