From: alexandre.belloni@free-electrons.com (Alexandre Belloni)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 6/7] watchdog: meson: allow setting timeout in devicetree
Date: Sat, 10 Feb 2018 00:19:10 +0100 [thread overview]
Message-ID: <20180209231910.GA2251@piout.net> (raw)
In-Reply-To: <20180209224849.GH19627@roeck-us.net>
Hi Guenter,
On 09/02/2018 at 14:48:49 -0800, Guenter Roeck wrote:
> On Fri, Feb 09, 2018 at 08:27:23PM +0100, Marcus Folkesson wrote:
> > watchdog_init_timeout() will allways pick timeout_param since it
> > defaults to a valid timeout.
> >
> > By following best practice described in
> > Documentation/watchdog/watchdog-kernel-api.txt, it also
> > let us to set timout-sec property in devicetree.
> >
> > Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
>
> Reviewed-by: Guenetr Roeck <linux@roeck-us.net>
^
A small typo in your name
> > ---
> > Documentation/devicetree/bindings/watchdog/meson-wdt.txt | 4 ++++
> > drivers/watchdog/meson_wdt.c | 2 +-
> > 2 files changed, 5 insertions(+), 1 deletion(-)
> >
> > diff --git a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
> > index 8a6d84cb36c9..7588cc3971bf 100644
> > --- a/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
> > +++ b/Documentation/devicetree/bindings/watchdog/meson-wdt.txt
> > @@ -9,9 +9,13 @@ Required properties:
> > "amlogic,meson8m2-wdt" and "amlogic,meson8b-wdt" on Meson8m2 SoCs
> > - reg : Specifies base physical address and size of the registers.
> >
> > +Optional properties:
> > +- timeout-sec: contains the watchdog timeout in seconds.
> > +
> > Example:
> >
> > wdt: watchdog at c1109900 {
> > compatible = "amlogic,meson6-wdt";
> > reg = <0xc1109900 0x8>;
> > + timeout-sec = <10>;
> > };
> > diff --git a/drivers/watchdog/meson_wdt.c b/drivers/watchdog/meson_wdt.c
> > index 304274c67735..cd0275a6cdac 100644
> > --- a/drivers/watchdog/meson_wdt.c
> > +++ b/drivers/watchdog/meson_wdt.c
> > @@ -36,7 +36,7 @@
> > #define MESON_SEC_TO_TC(s, c) ((s) * (c))
> >
> > static bool nowayout = WATCHDOG_NOWAYOUT;
> > -static unsigned int timeout = MESON_WDT_TIMEOUT;
> > +static unsigned int timeout;
> >
> > struct meson_wdt_data {
> > unsigned int enable;
> > --
> > 2.15.1
> >
--
Alexandre Belloni, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
http://bootlin.com
next prev parent reply other threads:[~2018-02-09 23:19 UTC|newest]
Thread overview: 25+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <marcus.folkesson@gmail.com>
2012-05-10 17:52 ` [PATCH] ARM: davinci: turn off DDR PHY when entering deep sleep Marcus Folkesson
2012-05-21 17:38 ` Sekhar Nori
2012-05-24 11:46 ` Marcus Folkesson
2012-05-24 17:41 ` Sekhar Nori
2018-02-09 19:27 ` [PATCH 0/7] watchdog: make use of timeout-secs Marcus Folkesson
2018-02-09 19:27 ` [PATCH 1/7] watchdog: sama5d4: make use of timeout-secs provided in devicetree Marcus Folkesson
2018-02-09 19:32 ` Marcus Folkesson
2018-02-09 22:38 ` Guenter Roeck
2018-02-11 17:38 ` [1/7] " Guenter Roeck
2018-02-09 19:27 ` [PATCH 2/7] watchdog: sunxi: allow setting timeout " Marcus Folkesson
2018-02-09 22:39 ` Guenter Roeck
2018-02-09 19:27 ` [PATCH 3/7] watchdog: sirfsoc: " Marcus Folkesson
2018-02-09 22:40 ` Guenter Roeck
2018-02-09 19:27 ` [PATCH 4/7] watchdog: pnx4008: make use of timeout-secs provided " Marcus Folkesson
2018-02-09 22:41 ` Guenter Roeck
2018-02-09 22:43 ` Guenter Roeck
2018-02-09 19:27 ` [PATCH 5/7] watchdog: mtk: allow setting timeout " Marcus Folkesson
2018-02-09 22:43 ` Guenter Roeck
2018-02-09 19:27 ` [PATCH 6/7] watchdog: meson: " Marcus Folkesson
2018-02-09 22:48 ` Guenter Roeck
2018-02-09 23:19 ` Alexandre Belloni [this message]
2018-02-10 0:04 ` Guenter Roeck
2018-02-09 19:27 ` [PATCH 7/7] watchdog: coh901327: make use of timeout-secs provided " Marcus Folkesson
2018-02-09 22:52 ` Guenter Roeck
2018-02-10 8:54 ` Marcus Folkesson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180209231910.GA2251@piout.net \
--to=alexandre.belloni@free-electrons.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).