* [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board [not found] <1520503424-22985-1-git-send-email-ping.bai@nxp.com> @ 2018-03-08 10:03 ` Bai Ping 2018-03-08 15:35 ` Fabio Estevam ` (2 more replies) 2018-03-09 3:15 ` [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Shawn Guo [not found] ` <20180309233931.7xujvo4eg4g5ftri@rob-hp-laptop> 2 siblings, 3 replies; 10+ messages in thread From: Bai Ping @ 2018-03-08 10:03 UTC (permalink / raw) To: linux-arm-kernel Add dts file support for imx6sll EVK board. Signed-off-by: Bai Ping <ping.bai@nxp.com> --- change v3->v4 - update the license indentifier - remove leading zero of node - remove unused pin from hog group --- Documentation/devicetree/bindings/arm/fsl.txt | 4 + arch/arm/boot/dts/Makefile | 2 + arch/arm/boot/dts/imx6sll-evk.dts | 372 ++++++++++++++++++++++++++ 3 files changed, 378 insertions(+) create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt index cdb9dd7..8a1baa2 100644 --- a/Documentation/devicetree/bindings/arm/fsl.txt +++ b/Documentation/devicetree/bindings/arm/fsl.txt @@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board Required root node properties: - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; +i.MX6SLL EVK board +Required root node properties: + - compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; + Generic i.MX boards ------------------- diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index ade7a38..28bff8b 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -505,6 +505,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ dtb-$(CONFIG_SOC_IMX6SL) += \ imx6sl-evk.dtb \ imx6sl-warp.dtb +dtb-$(CONFIG_SOC_IMX6SLL) += \ + imx6sll-evk.dtb dtb-$(CONFIG_SOC_IMX6SX) += \ imx6sx-nitrogen6sx.dtb \ imx6sx-sabreauto.dtb \ diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts new file mode 100644 index 0000000..892fbec --- /dev/null +++ b/arch/arm/boot/dts/imx6sll-evk.dts @@ -0,0 +1,372 @@ +//SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright 2016 Freescale Semiconductor, Inc. + * Copyright 2017-2018 NXP. + * + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include "imx6sll.dtsi" + +/ { + model = "Freescale i.MX6SLL EVK Board"; + compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; + + memory at 80000000 { + reg = <0x80000000 0x80000000>; + }; + + backlight { + compatible = "pwm-backlight"; + pwms = <&pwm1 0 5000000>; + brightness-levels = <0 4 8 16 32 64 128 255>; + default-brightness-level = <6>; + status = "okay"; + }; + + reg_usb_otg1_vbus: reg-usb-otg1-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg1_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_usb_otg2_vbus: reg-usb-otg2-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_otg2_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_aud3v: reg-aud3v { + compatible = "regulator-fixed"; + regulator-name = "wm8962-supply-3v15"; + regulator-min-microvolt = <3150000>; + regulator-max-microvolt = <3150000>; + regulator-boot-on; + }; + + reg_aud4v: reg-aud4v { + compatible = "regulator-fixed"; + regulator-name = "wm8962-supply-4v2"; + regulator-min-microvolt = <4325000>; + regulator-max-microvolt = <4325000>; + regulator-boot-on; + }; + + reg_lcd: reg-lcd { + compatible = "regulator-fixed"; + regulator-name = "lcd-pwr"; + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reg_sd1_vmmc: reg-sd1-vmmc { + compatible = "regulator-fixed"; + regulator-name = "SD1_SPWR"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&cpu0 { + arm-supply = <&sw1a_reg>; + soc-supply = <&sw1c_reg>; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic: pfuze100 at 8 { + compatible = "fsl,pfuze100"; + reg = <0x08>; + + regulators { + sw1a_reg: sw1ab { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw1c_reg: sw1c { + regulator-min-microvolt = <300000>; + regulator-max-microvolt = <1875000>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <6250>; + }; + + sw2_reg: sw2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3a_reg: sw3a { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw3b_reg: sw3b { + regulator-min-microvolt = <400000>; + regulator-max-microvolt = <1975000>; + regulator-boot-on; + regulator-always-on; + }; + + sw4_reg: sw4 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + }; + + swbst_reg: swbst { + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5150000>; + }; + + snvs_reg: vsnvs { + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <3000000>; + regulator-boot-on; + regulator-always-on; + }; + + vref_reg: vrefddr { + regulator-boot-on; + regulator-always-on; + }; + + vgen1_reg: vgen1 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + regulator-always-on; + }; + + vgen2_reg: vgen2 { + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <1550000>; + }; + + vgen3_reg: vgen3 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + }; + + vgen4_reg: vgen4 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen5_reg: vgen5 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + vgen6_reg: vgen6 { + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + }; + }; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>; + + pinctrl_hog0: hog0grp { + pinmux = < + MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 + MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22 + MX6SLL_PAD_KEY_COL3__GPIO3_IO30 + MX6SLL_PAD_KEY_COL4__GPIO4_IO00 + MX6SLL_PAD_KEY_COL5__GPIO4_IO02 + >; + slew-rate = <0x1>; + drive-strength = <0x3>; + fsl,pin-speed = <0x1>; + bias-pull-up = <0x1>; + input-schmitt-enable; + }; + + pinctrl_hog1: hog1grp { + pinmux = < + /* + * Must set the LVE of pad SD2_RESET, otherwise current + * leakage through eMMC chip will pull high the VCCQ to + * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch. + */ + MX6SLL_PAD_SD2_RESET__GPIO4_IO27 + >; + slew-rate = <0x1>; + drive-strength = <0x3>; + fsl,pin-speed = <0x1>; + bias-pull-up = <0x1>; + input-schmitt-enable; + fsl,low-voltage-enable = <0x1>; + }; + + pinctrl_uart1: uart1grp { + pinmux = < + MX6SLL_PAD_UART1_TXD__UART1_DCE_TX + MX6SLL_PAD_UART1_RXD__UART1_DCE_RX + >; + slew-rate = <0x1>; + drive-strength = <0x6>; + fsl,pin-speed = <0x2>; + bias-pull-up = <0x2>; + input-schmitt-enable; + }; + + pinctrl_usdhc1_data: usdhc1datagrp { + pinmux = < + MX6SLL_PAD_SD1_CMD__SD1_CMD + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 + >; + slew-rate = <0x1>; + drive-strength = <0x4>; + fsl,pin-speed = <0x1>; + bias-pull-up = <0x1>; + input-schmitt-enable; + }; + + pinctrl_usdhc1_clk: usdhc1clkgrp { + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>; + slew-rate = <0x1>; + drive-strength = <0x4>; + fsl,pin-speed = <0x1>; + bias-pull-down = <0x0>; + input-schmitt-enable; + }; + + pinctrl_usdhc1_data_100mhz: usdhc1datagrp_100mhz { + pinmux = < + MX6SLL_PAD_SD1_CMD__SD1_CMD + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 + >; + slew-rate = <0x1>; + drive-strength = <0x4>; + fsl,pin-speed = <0x2>; + bias-pull-up = <0x1>; + input-schmitt-enable; + }; + + pinctrl_usdhc1_clk_100mhz: usdhc1clkgrp_100mhz { + pinmux = < MX6SLL_PAD_SD1_CLK__SD1_CLK>; + slew-rate = <0x1>; + drive-strength = <0x4>; + fsl,pin-speed = <0x2>; + bias-pull-down = <0x0>; + input-schmitt-enable; + }; + + pinctrl_usdhc1_data_200mhz: usdhc1datagrp_200mhz { + pinmux = < + MX6SLL_PAD_SD1_CMD__SD1_CMD + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 + >; + slew-rate = <0x1>; + drive-strength = <0x5>; + fsl,pin-speed = <0x3>; + bias-pull-up = <0x1>; + input-schmitt-enable; + }; + + pinctrl_usdhc1_clk_200mhz: usdhc1clkgrp_200mhz { + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>; + slew-rate = <0x1>; + drive-strength = <0x7>; + fsl,pin-speed = <0x3>; + bias-pull-down = <0x0>; + input-schmitt-enable; + }; + + pinctrl_usbotg1: usbotg1grp { + pinmux = <MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID>; + slew-rate = <0x1>; + drive-strength = <0x3>; + fsl,pin-speed = <0x1>; + bias-pull-up = <0x1>; + input-schmitt-enable; + }; + + pinctrl_i2c1: i2c1grp { + pinmux = < + MX6SLL_PAD_I2C1_SCL__I2C1_SCL + MX6SLL_PAD_I2C1_SDA__I2C1_SDA + >; + slew-rate = <0x1>; + drive-strength = <0x6>; + fsl,pin-speed = <0x2>; + drive-open-drain; + bias-pull-up = <0x2>; + input-schmitt-enable; + input-enable; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&usdhc1 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc1_data>, <&pinctrl_usdhc1_clk>; + pinctrl-1 = <&pinctrl_usdhc1_data_100mhz>, <&pinctrl_usdhc1_clk_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_data_200mhz>, <&pinctrl_usdhc1_clk_200mhz>; + cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; + keep-power-in-suspend; + wakeup-source; + vmmc-supply = <®_sd1_vmmc>; + status = "okay"; +}; + +&usbotg1 { + vbus-supply = <®_usb_otg1_vbus>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usbotg1>; + disable-over-current; + srp-disable; + hnp-disable; + adp-disable; + status = "okay"; +}; + +&usbotg2 { + vbus-supply = <®_usb_otg2_vbus>; + dr_mode = "host"; + disable-over-current; + status = "okay"; +}; -- 1.9.1 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board 2018-03-08 10:03 ` [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Bai Ping @ 2018-03-08 15:35 ` Fabio Estevam 2018-03-09 3:36 ` Shawn Guo 2018-03-09 23:44 ` Rob Herring 2 siblings, 0 replies; 10+ messages in thread From: Fabio Estevam @ 2018-03-08 15:35 UTC (permalink / raw) To: linux-arm-kernel On Thu, Mar 8, 2018 at 7:03 AM, Bai Ping <ping.bai@nxp.com> wrote: > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>; > + > + pinctrl_hog0: hog0grp { > + pinmux = < > + MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 > + MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22 > + MX6SLL_PAD_KEY_COL3__GPIO3_IO30 > + MX6SLL_PAD_KEY_COL4__GPIO4_IO00 > + MX6SLL_PAD_KEY_COL5__GPIO4_IO02 > + >; > + slew-rate = <0x1>; > + drive-strength = <0x3>; > + fsl,pin-speed = <0x1>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + }; Please use the old style for pinctrl. ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board 2018-03-08 10:03 ` [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Bai Ping 2018-03-08 15:35 ` Fabio Estevam @ 2018-03-09 3:36 ` Shawn Guo 2018-03-09 5:06 ` Jacky Bai 2018-03-09 23:44 ` Rob Herring 2 siblings, 1 reply; 10+ messages in thread From: Shawn Guo @ 2018-03-09 3:36 UTC (permalink / raw) To: linux-arm-kernel On Thu, Mar 08, 2018 at 06:03:44PM +0800, Bai Ping wrote: > Add dts file support for imx6sll EVK board. > > Signed-off-by: Bai Ping <ping.bai@nxp.com> > --- > change v3->v4 > - update the license indentifier > - remove leading zero of node > - remove unused pin from hog group > --- > Documentation/devicetree/bindings/arm/fsl.txt | 4 + > arch/arm/boot/dts/Makefile | 2 + > arch/arm/boot/dts/imx6sll-evk.dts | 372 ++++++++++++++++++++++++++ > 3 files changed, 378 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts > > diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt > index cdb9dd7..8a1baa2 100644 > --- a/Documentation/devicetree/bindings/arm/fsl.txt > +++ b/Documentation/devicetree/bindings/arm/fsl.txt > @@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board > Required root node properties: > - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; > > +i.MX6SLL EVK board > +Required root node properties: > + - compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; > + > Generic i.MX boards > ------------------- > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index ade7a38..28bff8b 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -505,6 +505,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > dtb-$(CONFIG_SOC_IMX6SL) += \ > imx6sl-evk.dtb \ > imx6sl-warp.dtb > +dtb-$(CONFIG_SOC_IMX6SLL) += \ > + imx6sll-evk.dtb > dtb-$(CONFIG_SOC_IMX6SX) += \ > imx6sx-nitrogen6sx.dtb \ > imx6sx-sabreauto.dtb \ > diff --git a/arch/arm/boot/dts/imx6sll-evk.dts b/arch/arm/boot/dts/imx6sll-evk.dts > new file mode 100644 > index 0000000..892fbec > --- /dev/null > +++ b/arch/arm/boot/dts/imx6sll-evk.dts > @@ -0,0 +1,372 @@ > +//SPDX-License-Identifier: (GPL-2.0 OR MIT) Missing space after //. > +/* > + * Copyright 2016 Freescale Semiconductor, Inc. > + * Copyright 2017-2018 NXP. > + * > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include "imx6sll.dtsi" > + > +/ { > + model = "Freescale i.MX6SLL EVK Board"; > + compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; > + > + memory at 80000000 { > + reg = <0x80000000 0x80000000>; > + }; > + > + backlight { > + compatible = "pwm-backlight"; > + pwms = <&pwm1 0 5000000>; > + brightness-levels = <0 4 8 16 32 64 128 255>; > + default-brightness-level = <6>; > + status = "okay"; > + }; > + > + reg_usb_otg1_vbus: reg-usb-otg1-vbus { regulator-xxx for node name. > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg1_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_usb_otg2_vbus: reg-usb-otg2-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_otg2_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_aud3v: reg-aud3v { > + compatible = "regulator-fixed"; > + regulator-name = "wm8962-supply-3v15"; > + regulator-min-microvolt = <3150000>; > + regulator-max-microvolt = <3150000>; > + regulator-boot-on; > + }; > + > + reg_aud4v: reg-aud4v { > + compatible = "regulator-fixed"; > + regulator-name = "wm8962-supply-4v2"; > + regulator-min-microvolt = <4325000>; > + regulator-max-microvolt = <4325000>; > + regulator-boot-on; > + }; > + > + reg_lcd: reg-lcd { > + compatible = "regulator-fixed"; > + regulator-name = "lcd-pwr"; > + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reg_sd1_vmmc: reg-sd1-vmmc { > + compatible = "regulator-fixed"; > + regulator-name = "SD1_SPWR"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > +}; > + > +&cpu0 { > + arm-supply = <&sw1a_reg>; > + soc-supply = <&sw1c_reg>; > +}; > + > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + pmic: pfuze100 at 8 { pfuze100: pmic > + compatible = "fsl,pfuze100"; > + reg = <0x08>; > + > + regulators { > + sw1a_reg: sw1ab { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <6250>; > + }; > + > + sw1c_reg: sw1c { > + regulator-min-microvolt = <300000>; > + regulator-max-microvolt = <1875000>; > + regulator-boot-on; > + regulator-always-on; > + regulator-ramp-delay = <6250>; > + }; > + > + sw2_reg: sw2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3a_reg: sw3a { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw3b_reg: sw3b { > + regulator-min-microvolt = <400000>; > + regulator-max-microvolt = <1975000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + sw4_reg: sw4 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + swbst_reg: swbst { > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5150000>; > + }; > + > + snvs_reg: vsnvs { > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <3000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vref_reg: vrefddr { > + regulator-boot-on; > + regulator-always-on; > + }; > + > + vgen1_reg: vgen1 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + regulator-always-on; > + }; > + > + vgen2_reg: vgen2 { > + regulator-min-microvolt = <800000>; > + regulator-max-microvolt = <1550000>; > + }; > + > + vgen3_reg: vgen3 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + }; > + > + vgen4_reg: vgen4 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen5_reg: vgen5 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + vgen6_reg: vgen6 { > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + }; > + }; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>; > + > + pinctrl_hog0: hog0grp { > + pinmux = < > + MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 > + MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22 > + MX6SLL_PAD_KEY_COL3__GPIO3_IO30 > + MX6SLL_PAD_KEY_COL4__GPIO4_IO00 > + MX6SLL_PAD_KEY_COL5__GPIO4_IO02 I don't think these GPIOs should be in hog group, as they are used by particular client device, and should be in pinctrl entries for the client devices. Shawn > + >; > + slew-rate = <0x1>; > + drive-strength = <0x3>; > + fsl,pin-speed = <0x1>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + }; > + > + pinctrl_hog1: hog1grp { > + pinmux = < > + /* > + * Must set the LVE of pad SD2_RESET, otherwise current > + * leakage through eMMC chip will pull high the VCCQ to > + * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch. > + */ > + MX6SLL_PAD_SD2_RESET__GPIO4_IO27 > + >; > + slew-rate = <0x1>; > + drive-strength = <0x3>; > + fsl,pin-speed = <0x1>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + fsl,low-voltage-enable = <0x1>; > + }; > + > + pinctrl_uart1: uart1grp { > + pinmux = < > + MX6SLL_PAD_UART1_TXD__UART1_DCE_TX > + MX6SLL_PAD_UART1_RXD__UART1_DCE_RX > + >; > + slew-rate = <0x1>; > + drive-strength = <0x6>; > + fsl,pin-speed = <0x2>; > + bias-pull-up = <0x2>; > + input-schmitt-enable; > + }; > + > + pinctrl_usdhc1_data: usdhc1datagrp { > + pinmux = < > + MX6SLL_PAD_SD1_CMD__SD1_CMD > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 > + >; > + slew-rate = <0x1>; > + drive-strength = <0x4>; > + fsl,pin-speed = <0x1>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + }; > + > + pinctrl_usdhc1_clk: usdhc1clkgrp { > + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>; > + slew-rate = <0x1>; > + drive-strength = <0x4>; > + fsl,pin-speed = <0x1>; > + bias-pull-down = <0x0>; > + input-schmitt-enable; > + }; > + > + pinctrl_usdhc1_data_100mhz: usdhc1datagrp_100mhz { > + pinmux = < > + MX6SLL_PAD_SD1_CMD__SD1_CMD > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 > + >; > + slew-rate = <0x1>; > + drive-strength = <0x4>; > + fsl,pin-speed = <0x2>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + }; > + > + pinctrl_usdhc1_clk_100mhz: usdhc1clkgrp_100mhz { > + pinmux = < MX6SLL_PAD_SD1_CLK__SD1_CLK>; > + slew-rate = <0x1>; > + drive-strength = <0x4>; > + fsl,pin-speed = <0x2>; > + bias-pull-down = <0x0>; > + input-schmitt-enable; > + }; > + > + pinctrl_usdhc1_data_200mhz: usdhc1datagrp_200mhz { > + pinmux = < > + MX6SLL_PAD_SD1_CMD__SD1_CMD > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 > + >; > + slew-rate = <0x1>; > + drive-strength = <0x5>; > + fsl,pin-speed = <0x3>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + }; > + > + pinctrl_usdhc1_clk_200mhz: usdhc1clkgrp_200mhz { > + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>; > + slew-rate = <0x1>; > + drive-strength = <0x7>; > + fsl,pin-speed = <0x3>; > + bias-pull-down = <0x0>; > + input-schmitt-enable; > + }; > + > + pinctrl_usbotg1: usbotg1grp { > + pinmux = <MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID>; > + slew-rate = <0x1>; > + drive-strength = <0x3>; > + fsl,pin-speed = <0x1>; > + bias-pull-up = <0x1>; > + input-schmitt-enable; > + }; > + > + pinctrl_i2c1: i2c1grp { > + pinmux = < > + MX6SLL_PAD_I2C1_SCL__I2C1_SCL > + MX6SLL_PAD_I2C1_SDA__I2C1_SDA > + >; > + slew-rate = <0x1>; > + drive-strength = <0x6>; > + fsl,pin-speed = <0x2>; > + drive-open-drain; > + bias-pull-up = <0x2>; > + input-schmitt-enable; > + input-enable; > + }; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&usdhc1 { > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > + pinctrl-0 = <&pinctrl_usdhc1_data>, <&pinctrl_usdhc1_clk>; > + pinctrl-1 = <&pinctrl_usdhc1_data_100mhz>, <&pinctrl_usdhc1_clk_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc1_data_200mhz>, <&pinctrl_usdhc1_clk_200mhz>; > + cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; > + keep-power-in-suspend; > + wakeup-source; > + vmmc-supply = <®_sd1_vmmc>; > + status = "okay"; > +}; > + > +&usbotg1 { > + vbus-supply = <®_usb_otg1_vbus>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usbotg1>; > + disable-over-current; > + srp-disable; > + hnp-disable; > + adp-disable; > + status = "okay"; > +}; > + > +&usbotg2 { > + vbus-supply = <®_usb_otg2_vbus>; > + dr_mode = "host"; > + disable-over-current; > + status = "okay"; > +}; > -- > 1.9.1 > > > _______________________________________________ > linux-arm-kernel mailing list > linux-arm-kernel at lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board 2018-03-09 3:36 ` Shawn Guo @ 2018-03-09 5:06 ` Jacky Bai 0 siblings, 0 replies; 10+ messages in thread From: Jacky Bai @ 2018-03-09 5:06 UTC (permalink / raw) To: linux-arm-kernel > Subject: Re: [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK > board > > On Thu, Mar 08, 2018 at 06:03:44PM +0800, Bai Ping wrote: > > Add dts file support for imx6sll EVK board. > > > > Signed-off-by: Bai Ping <ping.bai@nxp.com> > > --- > > change v3->v4 > > - update the license indentifier > > - remove leading zero of node > > - remove unused pin from hog group > > --- > > Documentation/devicetree/bindings/arm/fsl.txt | 4 + > > arch/arm/boot/dts/Makefile | 2 + > > arch/arm/boot/dts/imx6sll-evk.dts | 372 > ++++++++++++++++++++++++++ > > 3 files changed, 378 insertions(+) > > create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts > > > > diff --git a/Documentation/devicetree/bindings/arm/fsl.txt > > b/Documentation/devicetree/bindings/arm/fsl.txt > > index cdb9dd7..8a1baa2 100644 > > --- a/Documentation/devicetree/bindings/arm/fsl.txt > > +++ b/Documentation/devicetree/bindings/arm/fsl.txt > > @@ -53,6 +53,10 @@ i.MX6 Quad SABRE Automotive Board Required root > > node properties: > > - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q"; > > > > +i.MX6SLL EVK board > > +Required root node properties: > > + - compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; > > + > > Generic i.MX boards > > ------------------- > > > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > > index ade7a38..28bff8b 100644 > > --- a/arch/arm/boot/dts/Makefile > > +++ b/arch/arm/boot/dts/Makefile > > @@ -505,6 +505,8 @@ dtb-$(CONFIG_SOC_IMX6Q) += \ > > dtb-$(CONFIG_SOC_IMX6SL) += \ > > imx6sl-evk.dtb \ > > imx6sl-warp.dtb > > +dtb-$(CONFIG_SOC_IMX6SLL) += \ > > + imx6sll-evk.dtb > > dtb-$(CONFIG_SOC_IMX6SX) += \ > > imx6sx-nitrogen6sx.dtb \ > > imx6sx-sabreauto.dtb \ > > diff --git a/arch/arm/boot/dts/imx6sll-evk.dts > > b/arch/arm/boot/dts/imx6sll-evk.dts > > new file mode 100644 > > index 0000000..892fbec > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6sll-evk.dts > > @@ -0,0 +1,372 @@ > > +//SPDX-License-Identifier: (GPL-2.0 OR MIT) > > Missing space after //. > OK, will fix the comments of this patch in V5. Jacky > > +/* > > + * Copyright 2016 Freescale Semiconductor, Inc. > > + * Copyright 2017-2018 NXP. > > + * > > + */ > > + > > +/dts-v1/; > > + > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/input/input.h> > > +#include "imx6sll.dtsi" > > + > > +/ { > > + model = "Freescale i.MX6SLL EVK Board"; > > + compatible = "fsl,imx6sll-evk", "fsl,imx6sll"; > > + > > + memory at 80000000 { > > + reg = <0x80000000 0x80000000>; > > + }; > > + > > + backlight { > > + compatible = "pwm-backlight"; > > + pwms = <&pwm1 0 5000000>; > > + brightness-levels = <0 4 8 16 32 64 128 255>; > > + default-brightness-level = <6>; > > + status = "okay"; > > + }; > > + > > + reg_usb_otg1_vbus: reg-usb-otg1-vbus { > > regulator-xxx for node name. > > > + compatible = "regulator-fixed"; > > + regulator-name = "usb_otg1_vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + gpio = <&gpio4 0 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > + > > + reg_usb_otg2_vbus: reg-usb-otg2-vbus { > > + compatible = "regulator-fixed"; > > + regulator-name = "usb_otg2_vbus"; > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5000000>; > > + gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > + > > + reg_aud3v: reg-aud3v { > > + compatible = "regulator-fixed"; > > + regulator-name = "wm8962-supply-3v15"; > > + regulator-min-microvolt = <3150000>; > > + regulator-max-microvolt = <3150000>; > > + regulator-boot-on; > > + }; > > + > > + reg_aud4v: reg-aud4v { > > + compatible = "regulator-fixed"; > > + regulator-name = "wm8962-supply-4v2"; > > + regulator-min-microvolt = <4325000>; > > + regulator-max-microvolt = <4325000>; > > + regulator-boot-on; > > + }; > > + > > + reg_lcd: reg-lcd { > > + compatible = "regulator-fixed"; > > + regulator-name = "lcd-pwr"; > > + gpio = <&gpio4 8 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > + > > + reg_sd1_vmmc: reg-sd1-vmmc { > > + compatible = "regulator-fixed"; > > + regulator-name = "SD1_SPWR"; > > + regulator-min-microvolt = <3000000>; > > + regulator-max-microvolt = <3000000>; > > + gpio = <&gpio3 30 GPIO_ACTIVE_HIGH>; > > + enable-active-high; > > + }; > > +}; > > + > > +&cpu0 { > > + arm-supply = <&sw1a_reg>; > > + soc-supply = <&sw1c_reg>; > > +}; > > + > > +&i2c1 { > > + clock-frequency = <100000>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_i2c1>; > > + status = "okay"; > > + > > + pmic: pfuze100 at 8 { > > pfuze100: pmic > > > + compatible = "fsl,pfuze100"; > > + reg = <0x08>; > > + > > + regulators { > > + sw1a_reg: sw1ab { > > + regulator-min-microvolt = <300000>; > > + regulator-max-microvolt = <1875000>; > > + regulator-boot-on; > > + regulator-always-on; > > + regulator-ramp-delay = <6250>; > > + }; > > + > > + sw1c_reg: sw1c { > > + regulator-min-microvolt = <300000>; > > + regulator-max-microvolt = <1875000>; > > + regulator-boot-on; > > + regulator-always-on; > > + regulator-ramp-delay = <6250>; > > + }; > > + > > + sw2_reg: sw2 { > > + regulator-min-microvolt = <800000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-boot-on; > > + regulator-always-on; > > + }; > > + > > + sw3a_reg: sw3a { > > + regulator-min-microvolt = <400000>; > > + regulator-max-microvolt = <1975000>; > > + regulator-boot-on; > > + regulator-always-on; > > + }; > > + > > + sw3b_reg: sw3b { > > + regulator-min-microvolt = <400000>; > > + regulator-max-microvolt = <1975000>; > > + regulator-boot-on; > > + regulator-always-on; > > + }; > > + > > + sw4_reg: sw4 { > > + regulator-min-microvolt = <800000>; > > + regulator-max-microvolt = <3300000>; > > + }; > > + > > + swbst_reg: swbst { > > + regulator-min-microvolt = <5000000>; > > + regulator-max-microvolt = <5150000>; > > + }; > > + > > + snvs_reg: vsnvs { > > + regulator-min-microvolt = <1000000>; > > + regulator-max-microvolt = <3000000>; > > + regulator-boot-on; > > + regulator-always-on; > > + }; > > + > > + vref_reg: vrefddr { > > + regulator-boot-on; > > + regulator-always-on; > > + }; > > + > > + vgen1_reg: vgen1 { > > + regulator-min-microvolt = <800000>; > > + regulator-max-microvolt = <1550000>; > > + regulator-always-on; > > + }; > > + > > + vgen2_reg: vgen2 { > > + regulator-min-microvolt = <800000>; > > + regulator-max-microvolt = <1550000>; > > + }; > > + > > + vgen3_reg: vgen3 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <3300000>; > > + }; > > + > > + vgen4_reg: vgen4 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + }; > > + > > + vgen5_reg: vgen5 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + }; > > + > > + vgen6_reg: vgen6 { > > + regulator-min-microvolt = <1800000>; > > + regulator-max-microvolt = <3300000>; > > + regulator-always-on; > > + }; > > + }; > > + }; > > +}; > > + > > +&iomuxc { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_hog0>, <&pinctrl_hog1>; > > + > > + pinctrl_hog0: hog0grp { > > + pinmux = < > > + MX6SLL_PAD_KEY_ROW7__GPIO4_IO07 > > + MX6SLL_PAD_GPIO4_IO22__GPIO4_IO22 > > + MX6SLL_PAD_KEY_COL3__GPIO3_IO30 > > + MX6SLL_PAD_KEY_COL4__GPIO4_IO00 > > + MX6SLL_PAD_KEY_COL5__GPIO4_IO02 > > I don't think these GPIOs should be in hog group, as they are used by particular > client device, and should be in pinctrl entries for the client devices. > > Shawn > > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x3>; > > + fsl,pin-speed = <0x1>; > > + bias-pull-up = <0x1>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_hog1: hog1grp { > > + pinmux = < > > + /* > > + * Must set the LVE of pad SD2_RESET, otherwise current > > + * leakage through eMMC chip will pull high the VCCQ to > > + * 2.6v, which will impact SD1 and SD3 SD3.0 voltage switch. > > + */ > > + MX6SLL_PAD_SD2_RESET__GPIO4_IO27 > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x3>; > > + fsl,pin-speed = <0x1>; > > + bias-pull-up = <0x1>; > > + input-schmitt-enable; > > + fsl,low-voltage-enable = <0x1>; > > + }; > > + > > + pinctrl_uart1: uart1grp { > > + pinmux = < > > + MX6SLL_PAD_UART1_TXD__UART1_DCE_TX > > + MX6SLL_PAD_UART1_RXD__UART1_DCE_RX > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x6>; > > + fsl,pin-speed = <0x2>; > > + bias-pull-up = <0x2>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usdhc1_data: usdhc1datagrp { > > + pinmux = < > > + MX6SLL_PAD_SD1_CMD__SD1_CMD > > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 > > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 > > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 > > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x4>; > > + fsl,pin-speed = <0x1>; > > + bias-pull-up = <0x1>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usdhc1_clk: usdhc1clkgrp { > > + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>; > > + slew-rate = <0x1>; > > + drive-strength = <0x4>; > > + fsl,pin-speed = <0x1>; > > + bias-pull-down = <0x0>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usdhc1_data_100mhz: usdhc1datagrp_100mhz { > > + pinmux = < > > + MX6SLL_PAD_SD1_CMD__SD1_CMD > > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 > > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 > > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 > > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x4>; > > + fsl,pin-speed = <0x2>; > > + bias-pull-up = <0x1>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usdhc1_clk_100mhz: usdhc1clkgrp_100mhz { > > + pinmux = < MX6SLL_PAD_SD1_CLK__SD1_CLK>; > > + slew-rate = <0x1>; > > + drive-strength = <0x4>; > > + fsl,pin-speed = <0x2>; > > + bias-pull-down = <0x0>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usdhc1_data_200mhz: usdhc1datagrp_200mhz { > > + pinmux = < > > + MX6SLL_PAD_SD1_CMD__SD1_CMD > > + MX6SLL_PAD_SD1_DATA0__SD1_DATA0 > > + MX6SLL_PAD_SD1_DATA1__SD1_DATA1 > > + MX6SLL_PAD_SD1_DATA2__SD1_DATA2 > > + MX6SLL_PAD_SD1_DATA3__SD1_DATA3 > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x5>; > > + fsl,pin-speed = <0x3>; > > + bias-pull-up = <0x1>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usdhc1_clk_200mhz: usdhc1clkgrp_200mhz { > > + pinmux = <MX6SLL_PAD_SD1_CLK__SD1_CLK>; > > + slew-rate = <0x1>; > > + drive-strength = <0x7>; > > + fsl,pin-speed = <0x3>; > > + bias-pull-down = <0x0>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_usbotg1: usbotg1grp { > > + pinmux = <MX6SLL_PAD_EPDC_PWR_COM__USB_OTG1_ID>; > > + slew-rate = <0x1>; > > + drive-strength = <0x3>; > > + fsl,pin-speed = <0x1>; > > + bias-pull-up = <0x1>; > > + input-schmitt-enable; > > + }; > > + > > + pinctrl_i2c1: i2c1grp { > > + pinmux = < > > + MX6SLL_PAD_I2C1_SCL__I2C1_SCL > > + MX6SLL_PAD_I2C1_SDA__I2C1_SDA > > + >; > > + slew-rate = <0x1>; > > + drive-strength = <0x6>; > > + fsl,pin-speed = <0x2>; > > + drive-open-drain; > > + bias-pull-up = <0x2>; > > + input-schmitt-enable; > > + input-enable; > > + }; > > +}; > > + > > +&uart1 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_uart1>; > > + status = "okay"; > > +}; > > + > > +&usdhc1 { > > + pinctrl-names = "default", "state_100mhz", "state_200mhz"; > > + pinctrl-0 = <&pinctrl_usdhc1_data>, <&pinctrl_usdhc1_clk>; > > + pinctrl-1 = <&pinctrl_usdhc1_data_100mhz>, > <&pinctrl_usdhc1_clk_100mhz>; > > + pinctrl-2 = <&pinctrl_usdhc1_data_200mhz>, > <&pinctrl_usdhc1_clk_200mhz>; > > + cd-gpios = <&gpio4 7 GPIO_ACTIVE_LOW>; > > + wp-gpios = <&gpio4 22 GPIO_ACTIVE_HIGH>; > > + keep-power-in-suspend; > > + wakeup-source; > > + vmmc-supply = <®_sd1_vmmc>; > > + status = "okay"; > > +}; > > + > > +&usbotg1 { > > + vbus-supply = <®_usb_otg1_vbus>; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_usbotg1>; > > + disable-over-current; > > + srp-disable; > > + hnp-disable; > > + adp-disable; > > + status = "okay"; > > +}; > > + > > +&usbotg2 { > > + vbus-supply = <®_usb_otg2_vbus>; > > + dr_mode = "host"; > > + disable-over-current; > > + status = "okay"; > > +}; > > -- > > 1.9.1 > > > > > > _______________________________________________ > > linux-arm-kernel mailing list > > linux-arm-kernel at lists.infradead.org > > https://emea01.safelinks.protection.outlook.com/?url=http%3A%2F%2Flist > > > s.infradead.org%2Fmailman%2Flistinfo%2Flinux-arm-kernel&data=02%7C01%7 > > > Cping.bai%40nxp.com%7Ccc2d554875244f40801108d5856f03b5%7C686ea1d3 > bc2b4 > > > c6fa92cd99c5c301635%7C0%7C0%7C636561634214012078&sdata=maWc00% > 2BYifMKn > > oiD8rVmQFIWsHDgcIfN58UuarYqfCQ%3D&reserved=0 ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board 2018-03-08 10:03 ` [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Bai Ping 2018-03-08 15:35 ` Fabio Estevam 2018-03-09 3:36 ` Shawn Guo @ 2018-03-09 23:44 ` Rob Herring 2 siblings, 0 replies; 10+ messages in thread From: Rob Herring @ 2018-03-09 23:44 UTC (permalink / raw) To: linux-arm-kernel On Thu, Mar 08, 2018 at 06:03:44PM +0800, Bai Ping wrote: > Add dts file support for imx6sll EVK board. > > Signed-off-by: Bai Ping <ping.bai@nxp.com> > --- > change v3->v4 > - update the license indentifier > - remove leading zero of node > - remove unused pin from hog group > --- > Documentation/devicetree/bindings/arm/fsl.txt | 4 + > arch/arm/boot/dts/Makefile | 2 + > arch/arm/boot/dts/imx6sll-evk.dts | 372 ++++++++++++++++++++++++++ > 3 files changed, 378 insertions(+) > create mode 100644 arch/arm/boot/dts/imx6sll-evk.dts One nit, otherwise: Reviewed-by: Rob Herring <robh@kernel.org> > +&i2c1 { > + clock-frequency = <100000>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + pmic: pfuze100 at 8 { pmic at ... > + compatible = "fsl,pfuze100"; > + reg = <0x08>; ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll [not found] <1520503424-22985-1-git-send-email-ping.bai@nxp.com> 2018-03-08 10:03 ` [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Bai Ping @ 2018-03-09 3:15 ` Shawn Guo 2018-03-09 5:04 ` Jacky Bai [not found] ` <20180309233931.7xujvo4eg4g5ftri@rob-hp-laptop> 2 siblings, 1 reply; 10+ messages in thread From: Shawn Guo @ 2018-03-09 3:15 UTC (permalink / raw) To: linux-arm-kernel Looks pretty good, except that we should follow device tree specification recommendation to name device as much as possible. https://github.com/devicetree-org/devicetree-specification/releases/tag/v0.2 On Thu, Mar 08, 2018 at 06:03:43PM +0800, Bai Ping wrote: > diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi > new file mode 100644 > index 0000000..3fb1156 > --- /dev/null > +++ b/arch/arm/boot/dts/imx6sll.dtsi > @@ -0,0 +1,806 @@ > +//SPDX-License-Identifier: (GPL-2.0 OR MIT) There should be space right after // > +/* > + * Copyright 2016 Freescale Semiconductor, Inc. > + * Copyright 2017-2018 NXP. > + * > + */ > + > +#include <dt-bindings/clock/imx6sll-clock.h> > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include "imx6sll-pinfunc.h" > + > +/ { > + #address-cells = <1>; > + #size-cells = <1>; > + > + aliases { > + gpio0 = &gpio1; > + gpio1 = &gpio2; > + gpio2 = &gpio3; > + gpio3 = &gpio4; > + gpio4 = &gpio5; > + gpio5 = &gpio6; > + i2c0 = &i2c1; > + i2c1 = &i2c2; > + i2c2 = &i2c3; > + mmc0 = &usdhc1; > + mmc1 = &usdhc2; > + mmc2 = &usdhc3; > + serial0 = &uart1; > + serial1 = &uart2; > + serial2 = &uart3; > + serial3 = &uart4; > + serial4 = &uart5; > + spi0 = &ecspi1; > + spi1 = &ecspi2; > + spi3 = &ecspi3; > + spi4 = &ecspi4; > + usbphy0 = &usbphy1; > + usbphy1 = &usbphy2; > + }; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + cpu0: cpu at 0 { > + compatible = "arm,cortex-a9"; > + device_type = "cpu"; > + reg = <0>; > + next-level-cache = <&L2>; > + operating-points = < > + /* kHz uV */ > + 996000 1225000 > + 792000 1175000 > + 396000 1075000 > + 198000 975000 > + >; > + fsl,soc-operating-points = < > + /* ARM kHz SOC-PU uV */ > + 996000 1225000 > + 792000 1175000 > + 396000 1175000 > + 198000 1175000 > + >; > + clock-latency = <61036>; /* two CLK32 periods */ > + fsl,low-power-run; What is this? > + clocks = <&clks IMX6SLL_CLK_ARM>, > + <&clks IMX6SLL_CLK_PLL2_PFD2>, > + <&clks IMX6SLL_CLK_STEP>, > + <&clks IMX6SLL_CLK_PLL1_SW>, > + <&clks IMX6SLL_CLK_PLL1_SYS>, > + <&clks IMX6SLL_CLK_PLL1>, > + <&clks IMX6SLL_PLL1_BYPASS>, > + <&clks IMX6SLL_PLL1_BYPASS_SRC>; > + clock-names = "arm", "pll2_pfd2_396m", "step", > + "pll1_sw", "pll1_sys", "pll1", "pll1_bypass", > + "pll1_bypass_src"; > + }; > + }; > + > + intc: interrupt-controller at a01000 { > + compatible = "arm,cortex-a9-gic"; > + #interrupt-cells = <3>; > + interrupt-controller; > + reg = <0x00a01000 0x1000>, > + <0x00a00100 0x100>; > + interrupt-parent = <&intc>; > + }; > + > + clocks { > + #address-cells = <1>; > + #size-cells = <0>; As requested by DT maintainer, please drop this container node and give an unique name for each fixed-clock, something like: clock-xxx { ... }; You may want to refer to how Lucas did it for i.MX8QM. > + > + ckil: clock at 0 { > + compatible = "fixed-clock"; > + reg = <0>; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + clock-output-names = "ckil"; > + }; > + > + osc: clock at 1 { > + compatible = "fixed-clock"; > + reg = <1>; > + #clock-cells = <0>; > + clock-frequency = <24000000>; > + clock-output-names = "osc"; > + }; > + > + ipp_di0: clock at 2 { > + compatible = "fixed-clock"; > + reg = <2>; > + #clock-cells = <0>; > + clock-frequency = <0>; > + clock-output-names = "ipp_di0"; > + }; > + > + ipp_di1: clock at 3 { > + compatible = "fixed-clock"; > + reg = <3>; > + #clock-cells = <0>; > + clock-frequency = <0>; > + clock-output-names = "ipp_di1"; > + }; > + }; > + > + soc { > + #address-cells = <1>; > + #size-cells = <1>; > + compatible = "simple-bus"; > + interrupt-parent = <&gpc>; > + ranges; > + > + ocram: sram at 900000 { > + compatible = "mmio-sram"; > + reg = <0x00900000 0x20000>; > + }; > + > + L2: l2-cache at a02000 { > + compatible = "arm,pl310-cache"; > + reg = <0x00a02000 0x1000>; > + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; > + cache-unified; > + cache-level = <2>; > + arm,tag-latency = <4 2 3>; > + arm,data-latency = <4 2 3>; > + }; > + > + aips1: aips-bus at 2000000 { > + compatible = "fsl,aips-bus", "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0x02000000 0x100000>; > + ranges; > + > + spba: spba-bus at 2000000 { > + compatible = "fsl,spba-bus", "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0x02000000 0x40000>; > + ranges; > + > + spdif: spdif at 2004000 { > + compatible = "fsl,imx6sl-spdif", "fsl,imx35-spdif"; > + reg = <0x02004000 0x4000>; > + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 14 18 0>, <&sdma 15 18 0>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_SPDIF_GCLK>, > + <&clks IMX6SLL_CLK_OSC>, > + <&clks IMX6SLL_CLK_SPDIF>, > + <&clks IMX6SLL_CLK_DUMMY>, > + <&clks IMX6SLL_CLK_DUMMY>, > + <&clks IMX6SLL_CLK_DUMMY>, > + <&clks IMX6SLL_CLK_IPG>, > + <&clks IMX6SLL_CLK_DUMMY>, > + <&clks IMX6SLL_CLK_DUMMY>, > + <&clks IMX6SLL_CLK_SPBA>; > + clock-names = "core", "rxtx0", > + "rxtx1", "rxtx2", > + "rxtx3", "rxtx4", > + "rxtx5", "rxtx6", > + "rxtx7", "dma"; > + status = "disabled"; > + }; > + > + ecspi1: ecspi at 2008000 { s/ecspi/spi for node name. > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > + reg = <0x02008000 0x4000>; > + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_ECSPI1>, > + <&clks IMX6SLL_CLK_ECSPI1>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + ecspi2: ecspi at 200c000 { > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > + reg = <0x0200c000 0x4000>; > + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 5 7 1>, <&sdma 6 7 2>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_ECSPI2>, > + <&clks IMX6SLL_CLK_ECSPI2>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + ecspi3: ecspi at 2010000 { > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > + reg = <0x02010000 0x4000>; > + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 7 7 1>, <&sdma 8 7 2>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_ECSPI3>, > + <&clks IMX6SLL_CLK_ECSPI3>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + ecspi4: ecspi at 2014000 { > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > + reg = <0x02014000 0x4000>; > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 9 7 1>, <&sdma 10 7 2>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_ECSPI4>, > + <&clks IMX6SLL_CLK_ECSPI4>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + uart4: serial at 2018000 { > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; > + reg = <0x02018000 0x4000>; > + interrupts =<GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_UART4_IPG>, > + <&clks IMX6SLL_CLK_UART4_SERIAL>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + uart1: serial at 2020000 { > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; > + reg = <0x02020000 0x4000>; > + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_UART1_IPG>, > + <&clks IMX6SLL_CLK_UART1_SERIAL>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + uart2: serial at 2024000 { > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; > + reg = <0x02024000 0x4000>; > + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_UART2_IPG>, > + <&clks IMX6SLL_CLK_UART2_SERIAL>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + > + ssi1: ssi at 2028000 { ssi-controller > + compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi"; > + reg = <0x02028000 0x4000>; > + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 37 22 0>, <&sdma 38 22 0>; > + dma-names = "rx", "tx"; > + fsl,fifo-depth = <15>; > + clocks = <&clks IMX6SLL_CLK_SSI1_IPG>, > + <&clks IMX6SLL_CLK_SSI1>; > + clock-names = "ipg", "baud"; > + status = "disabled"; > + }; > + > + ssi2: ssi2 at 202c000 { Drop 2 from node name. > + compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi"; > + reg = <0x0202c000 0x4000>; > + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 41 22 0>, <&sdma 42 22 0>; > + dma-names = "rx", "tx"; > + fsl,fifo-depth = <15>; > + clocks = <&clks IMX6SLL_CLK_SSI2_IPG>, > + <&clks IMX6SLL_CLK_SSI2>; > + clock-names = "ipg", "baud"; > + status = "disabled"; > + }; > + > + ssi3: ssi at 2030000 { > + compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi"; > + reg = <0x02030000 0x4000>; > + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 45 22 0>, <&sdma 46 22 0>; > + dma-names = "rx", "tx"; > + fsl,fifo-depth = <15>; > + clocks = <&clks IMX6SLL_CLK_SSI3_IPG>, > + <&clks IMX6SLL_CLK_SSI3>; > + clock-names = "ipg", "baud"; > + status = "disabled"; > + }; > + > + uart3: serial at 2034000 { > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; > + reg = <0x02034000 0x4000>; > + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; > + dma-name = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_UART3_IPG>, > + <&clks IMX6SLL_CLK_UART3_SERIAL>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + }; > + > + pwm1: pwm at 2080000 { > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > + reg = <0x02080000 0x4000>; > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_PWM1>, > + <&clks IMX6SLL_CLK_PWM1>; > + clock-names = "ipg", "per"; > + #pwm-cells = <2>; > + }; > + > + pwm2: pwm at 2084000 { > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > + reg = <0x02084000 0x4000>; > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_PWM2>, > + <&clks IMX6SLL_CLK_PWM2>; > + clock-names = "ipg", "per"; > + #pwm-cells = <2>; > + }; > + > + pwm3: pwm at 2088000 { > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > + reg = <0x02088000 0x4000>; > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_PWM3>, > + <&clks IMX6SLL_CLK_PWM3>; > + clock-names = "ipg", "per"; > + #pwm-cells = <2>; > + }; > + > + pwm4: pwm at 208c000 { > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > + reg = <0x0208c000 0x4000>; > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_PWM4>, > + <&clks IMX6SLL_CLK_PWM4>; > + clock-names = "ipg", "per"; > + #pwm-cells = <2>; > + }; > + > + gpt1: gpt at 2098000 { timer > + compatible = "fsl,imx6sll-gpt"; > + reg = <0x02098000 0x4000>; > + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_GPT_BUS>, > + <&clks IMX6SLL_CLK_GPT_SERIAL>; > + clock-names = "ipg", "per"; > + }; > + > + gpio1: gpio at 209c000 { > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > + reg = <0x0209c000 0x4000>; > + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + gpio2: gpio at 20a0000 { > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > + reg = <0x020a0000 0x4000>; > + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + gpio3: gpio at 20a4000 { > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > + reg = <0x020a4000 0x4000>; > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + gpio4: gpio at 20a8000 { > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > + reg = <0x020a8000 0x4000>; > + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + gpio5: gpio at 20ac000 { > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > + reg = <0x020ac000 0x4000>; > + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + gpio6: gpio at 20b0000 { > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > + reg = <0x020b0000 0x4000>; > + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; > + gpio-controller; > + #gpio-cells = <2>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + kpp: kpp at 20b8000 { s/kpp/keypad for node name. > + compatible = "fsl,imx6sll-kpp", "fsl,imx21-kpp"; > + reg = <0x020b8000 0x4000>; > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_KPP>; > + status = "disabled"; > + }; > + > + wdog1: wdog at 20bc000 { s/wdog/watchdog for node name. > + compatible = "fsl,imx6sll-wdt", "fsl,imx21-wdt"; > + reg = <0x020bc000 0x4000>; > + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_WDOG1>; > + }; > + > + wdog2: wdog at 20c0000 { > + compatible = "fsl,imx6sll-wdt", "fsl,imx21-wdt"; > + reg = <0x020c0000 0x4000>; > + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_WDOG2>; > + status = "disabled"; > + }; > + > + clks: clock-controller at 20c4000 { > + compatible = "fsl,imx6sll-ccm"; > + reg = <0x020c4000 0x4000>; > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; > + #clock-cells = <1>; > + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; > + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; > + > + assigned-clocks = <&clks IMX6SLL_CLK_PERCLK_SEL>; > + assigned-clock-parents = <&clks IMX6SLL_CLK_OSC>; > + }; > + > + anatop: anatop at 20c8000 { > + compatible = "fsl,imx6sll-anatop", > + "fsl,imx6q-anatop", > + "syscon", "simple-bus"; > + reg = <0x020c8000 0x4000>; > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg_3p0: regulator-3p0 at 20c8120 { > + compatible = "fsl,anatop-regulator"; > + reg = <0x20c8120>; > + regulator-name = "vdd3p0"; > + regulator-min-microvolt = <2625000>; > + regulator-max-microvolt = <3400000>; > + anatop-reg-offset = <0x120>; > + anatop-vol-bit-shift = <8>; > + anatop-vol-bit-width = <5>; > + anatop-min-bit-val = <0>; > + anatop-min-voltage = <2625000>; > + anatop-max-voltage = <3400000>; > + anatop-enable-bit = <0>; > + }; > + }; > + > + tempmon: tempmon { s/tempmon/temperature-sensor for node name. > + compatible = "fsl,imx6sll-tempmon", "fsl,imx6sx-tempmon"; > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; > + fsl,tempmon = <&anatop>; > + fsl,tempmon-data = <&ocotp>; > + clocks = <&clks IMX6SLL_CLK_PLL3_USB_OTG>; > + status = "disabled"; > + }; > + > + usbphy1: usbphy at 20c9000 { s/usbphy/usb-phy for node name. > + compatible = "fsl,imx6sll-usbphy", "fsl,imx6ul-usbphy", > + "fsl,imx23-usbphy"; > + reg = <0x020c9000 0x1000>; > + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USBPHY1>; > + phy-3p0-supply = <®_3p0>; > + fsl,anatop = <&anatop>; > + }; > + > + usbphy2: usbphy at 20ca000 { > + compatible = "fsl,imx6sll-usbphy", "fsl,imx6ul-usbphy", > + "fsl,imx23-usbphy"; > + reg = <0x020ca000 0x1000>; > + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USBPHY2>; > + phy-reg_3p0-supply = <®_3p0>; > + fsl,anatop = <&anatop>; > + }; > + > + snvs: snvs at 20cc000 { > + compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; > + reg = <0x020cc000 0x4000>; > + > + snvs_rtc: snvs-rtc-lp { > + compatible = "fsl,sec-v4.0-mon-rtc-lp"; > + regmap = <&snvs>; > + offset = <0x34>; > + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + snvs_poweroff: snvs-poweroff { > + compatible = "syscon-poweroff"; > + regmap = <&snvs>; > + offset = <0x38>; > + mask = <0x61>; > + }; > + > + snvs_pwrkey: snvs-powerkey { > + compatible = "fsl,sec-v4.0-pwrkey"; > + regmap = <&snvs>; > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > + linux,keycode = <KEY_POWER>; > + wakeup-source; > + }; > + }; > + > + epit1: epit at 20d0000 { > + reg = <0x020d0000 0x4000>; > + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; > + }; > + > + epit2: epit at 20d4000 { > + reg = <0x020d4000 0x4000>; > + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; > + }; No compatible, so unused? > + > + src: src at 20d8000 { reset-controller > + compatible = "fsl,imx6sll-src"; > + reg = <0x020d8000 0x4000>; > + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > + #reset-cells = <1>; > + }; > + > + gpc: gpc at 20dc000 { interrupt-controller > + compatible = "fsl,imx6sll-gpc", "fsl,imx6q-gpc"; > + reg = <0x020dc000 0x4000>; > + interrupt-controller; > + #interrupt-cells = <3>; > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; > + interrupt-parent = <&intc>; > + fsl,mf-mix-wakeup-irq = <0x7c00000 0x7d00 0x0 0x1400640>; What is this? > + }; > + > + iomuxc: iomuxc at 20e0000 { > + compatible = "fsl,imx6sll-iomuxc"; > + reg = <0x020e0000 0x4000>; > + }; > + > + gpr: iomuxc-gpr at 20e4000 { > + compatible = "fsl,imx6sll-iomuxc-gpr", > + "fsl,imx6q-iomuxc-gpr", "syscon"; > + reg = <0x020e4000 0x4000>; > + }; > + > + csi: csi at 20e8000 { > + compatible = "fsl,imx6sll-csi", "fsl,imx6s-csi"; > + reg = <0x020e8000 0x4000>; > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_DUMMY>, > + <&clks IMX6SLL_CLK_CSI>, > + <&clks IMX6SLL_CLK_DUMMY>; > + clock-names = "disp-axi", "csi_mclk", "disp_dcic"; > + status = "disabled"; > + }; > + > + sdma: sdma at 20ec000 { dma-controller > + compatible = "fsl,imx6sll-sdma", "fsl,imx35-sdma"; > + reg = <0x020ec000 0x4000>; > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_SDMA>, > + <&clks IMX6SLL_CLK_SDMA>; > + clock-names = "ipg", "ahb"; > + #dma-cells = <3>; > + iram = <&ocram>; > + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; > + }; > + > + lcdif: lcdif at 20f8000 { lcd-controller > + compatible = "fsl,imx6sll-lcdif", "fsl,imx28-lcdif"; > + reg = <0x020f8000 0x4000>; > + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_LCDIF_PIX>, > + <&clks IMX6SLL_CLK_LCDIF_APB>, > + <&clks IMX6SLL_CLK_DUMMY>; > + clock-names = "pix", "axi", "disp_axi"; > + status = "disabled"; > + }; > + > + dcp: dcp at 20fc000 { > + compatible = "fsl,imx6sl-dcp"; > + reg = <0x020fc000 0x4000>; > + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, > + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_DCP>; > + clock-names = "dcp"; > + }; > + }; > + > + aips2: aips-bus at 2100000 { > + compatible = "fsl,aips-bus", "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + reg = <0x02100000 0x100000>; > + ranges; > + > + usbotg1: usb at 2184000 { > + compatible = "fsl,imx6sll-usb", "fsl,imx6ul-usb", > + "fsl,imx27-usb"; > + reg = <0x02184000 0x200>; > + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USBOH3>; > + fsl,usbphy = <&usbphy1>; > + fsl,usbmisc = <&usbmisc 0>; > + fsl,anatop = <&anatop>; > + ahb-burst-config = <0x0>; > + tx-burst-size-dword = <0x10>; > + rx-burst-size-dword = <0x10>; > + status = "disabled"; > + }; > + > + usbotg2: usb at 2184200 { > + compatible = "fsl,imx6sll-usb", "fsl,imx6ul-usb", > + "fsl,imx27-usb"; > + reg = <0x02184200 0x200>; > + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USBOH3>; > + fsl,usbphy = <&usbphy2>; > + fsl,usbmisc = <&usbmisc 1>; > + ahb-burst-config = <0x0>; > + tx-burst-size-dword = <0x10>; > + rx-burst-size-dword = <0x10>; > + status = "disabled"; > + }; > + > + usbmisc: usbmisc at 2184800 { > + #index-cells = <1>; > + compatible = "fsl,imx6sll-usbmisc", "fsl,imx6ul-usbmisc", > + "fsl,imx6q-usbmisc"; > + reg = <0x02184800 0x200>; > + }; > + > + usdhc1: usdhc at 2190000 { s/usdhc/mmc for node name. > + compatible = "fsl,imx6sll-usdhc", "fsl,imx6sx-usdhc"; > + reg = <0x02190000 0x4000>; > + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USDHC1>, > + <&clks IMX6SLL_CLK_USDHC1>, > + <&clks IMX6SLL_CLK_USDHC1>; > + clock-names = "ipg", "ahb", "per"; > + bus-width = <4>; > + fsl,tuning-step = <2>; > + fsl,tuning-start-tap = <20>; > + status = "disabled"; > + }; > + > + usdhc2: usdhc at 2194000 { > + compatible = "fsl,imx6sll-usdhc", "fsl,imx6sx-usdhc"; > + reg = <0x02194000 0x4000>; > + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USDHC2>, > + <&clks IMX6SLL_CLK_USDHC2>, > + <&clks IMX6SLL_CLK_USDHC2>; > + clock-names = "ipg", "ahb", "per"; > + bus-width = <4>; > + fsl,tuning-step = <2>; > + fsl,tuning-start-tap = <20>; > + status = "disabled"; > + }; > + > + usdhc3: usdhc at 2198000 { > + compatible = "fsl,imx6sll-usdhc", "fsl,imx6sx-usdhc"; > + reg = <0x02198000 0x4000>; > + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_USDHC3>, > + <&clks IMX6SLL_CLK_USDHC3>, > + <&clks IMX6SLL_CLK_USDHC3>; > + clock-names = "ipg", "ahb", "per"; > + bus-width = <4>; > + fsl,tuning-step = <2>; > + fsl,tuning-start-tap = <20>; > + status = "disabled"; > + }; > + > + i2c1: i2c at 21a0000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "fs,imx6sll-i2c", "fsl,imx21-i2c"; > + reg = <0x021a0000 0x4000>; > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_I2C1>; > + status = "disabled"; > + }; > + > + i2c2: i2c at 21a4000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "fsl,imx6sll-i2c", "fsl,imx21-i2c"; > + reg = <0x021a4000 0x4000>; > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_I2C2>; > + status = "disabled"; > + }; > + > + i2c3: i2c at 21a8000 { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "fsl,imx6sll-i2c", "fsl,imx21-i2c"; > + reg = <0x021a8000 0x4000>; > + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_I2C3>; > + status = "disabled"; > + }; > + > + romcp at 21ac000 { > + compatible = "fsl,imx6sll-romcp", "syscon"; > + reg = <0x021ac000 0x4000>; > + }; > + > + mmdc: mmdc at 21b0000 { memory-controller Shawn > + compatible = "fsl,imx6sll-mmdc", "fsl,imx6q-mmdc"; > + reg = <0x021b0000 0x4000>; > + }; > + > + rngb: rngb at 21b4000 { > + reg = <0x021b4000 0x4000>; > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > + clocks = <&clks IMX6SLL_CLK_DUMMY>; > + }; > + > + ocotp: ocotp-ctrl at 21bc000 { > + compatible = "fsl,imx6sll-ocotp", "syscon"; > + reg = <0x021bc000 0x4000>; > + clocks = <&clks IMX6SLL_CLK_OCOTP>; > + }; > + > + snvs_gpr: snvs-gpr at 21c4000 { > + reg = <0x021c4000 0x10000>; > + }; > + > + iomuxc_snvs: iomuxc-snvs at 21c8000 { > + reg = <0x021c8000 0x10000>; > + }; > + > + audmux: audmux at 21d8000 { > + compatible = "fsl,imx6sll-audmux", "fsl,imx31-audmux"; > + reg = <0x021d8000 0x4000>; > + status = "disabled"; > + }; > + > + uart5: serial at 21f4000 { > + compatible = "fsl,imx6sll-uart", "fsl,imx6q-uart", "fsl,imx21-uart"; > + reg = <0x021f4000 0x4000>; > + interrupts =<GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; > + dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; > + dma-names = "rx", "tx"; > + clocks = <&clks IMX6SLL_CLK_UART5_IPG>, > + <&clks IMX6SLL_CLK_UART5_SERIAL>; > + clock-names = "ipg", "per"; > + status = "disabled"; > + }; > + }; > + }; > +}; > -- > 1.9.1 > ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll 2018-03-09 3:15 ` [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Shawn Guo @ 2018-03-09 5:04 ` Jacky Bai 0 siblings, 0 replies; 10+ messages in thread From: Jacky Bai @ 2018-03-09 5:04 UTC (permalink / raw) To: linux-arm-kernel > On Thu, Mar 08, 2018 at 06:03:43PM +0800, Bai Ping wrote: > > diff --git a/arch/arm/boot/dts/imx6sll.dtsi > > b/arch/arm/boot/dts/imx6sll.dtsi new file mode 100644 index > > 0000000..3fb1156 > > --- /dev/null > > +++ b/arch/arm/boot/dts/imx6sll.dtsi > > @@ -0,0 +1,806 @@ > > +//SPDX-License-Identifier: (GPL-2.0 OR MIT) > > There should be space right after // > Thanks for review, will fix all the comment in this patch. Jacky > > +/* > > + * Copyright 2016 Freescale Semiconductor, Inc. > > + * Copyright 2017-2018 NXP. > > + * > > + */ > > + > > +#include <dt-bindings/clock/imx6sll-clock.h> > > +#include <dt-bindings/gpio/gpio.h> > > +#include <dt-bindings/interrupt-controller/arm-gic.h> > > +#include "imx6sll-pinfunc.h" > > + > > +/ { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + > > + aliases { > > + gpio0 = &gpio1; > > + gpio1 = &gpio2; > > + gpio2 = &gpio3; > > + gpio3 = &gpio4; > > + gpio4 = &gpio5; > > + gpio5 = &gpio6; > > + i2c0 = &i2c1; > > + i2c1 = &i2c2; > > + i2c2 = &i2c3; > > + mmc0 = &usdhc1; > > + mmc1 = &usdhc2; > > + mmc2 = &usdhc3; > > + serial0 = &uart1; > > + serial1 = &uart2; > > + serial2 = &uart3; > > + serial3 = &uart4; > > + serial4 = &uart5; > > + spi0 = &ecspi1; > > + spi1 = &ecspi2; > > + spi3 = &ecspi3; > > + spi4 = &ecspi4; > > + usbphy0 = &usbphy1; > > + usbphy1 = &usbphy2; > > + }; > > + > > + cpus { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + cpu0: cpu at 0 { > > + compatible = "arm,cortex-a9"; > > + device_type = "cpu"; > > + reg = <0>; > > + next-level-cache = <&L2>; > > + operating-points = < > > + /* kHz uV */ > > + 996000 1225000 > > + 792000 1175000 > > + 396000 1075000 > > + 198000 975000 > > + >; > > + fsl,soc-operating-points = < > > + /* ARM kHz SOC-PU uV */ > > + 996000 1225000 > > + 792000 1175000 > > + 396000 1175000 > > + 198000 1175000 > > + >; > > + clock-latency = <61036>; /* two CLK32 periods */ > > + fsl,low-power-run; > > What is this? > > > + clocks = <&clks IMX6SLL_CLK_ARM>, > > + <&clks IMX6SLL_CLK_PLL2_PFD2>, > > + <&clks IMX6SLL_CLK_STEP>, > > + <&clks IMX6SLL_CLK_PLL1_SW>, > > + <&clks IMX6SLL_CLK_PLL1_SYS>, > > + <&clks IMX6SLL_CLK_PLL1>, > > + <&clks IMX6SLL_PLL1_BYPASS>, > > + <&clks IMX6SLL_PLL1_BYPASS_SRC>; > > + clock-names = "arm", "pll2_pfd2_396m", "step", > > + "pll1_sw", "pll1_sys", "pll1", "pll1_bypass", > > + "pll1_bypass_src"; > > + }; > > + }; > > + > > + intc: interrupt-controller at a01000 { > > + compatible = "arm,cortex-a9-gic"; > > + #interrupt-cells = <3>; > > + interrupt-controller; > > + reg = <0x00a01000 0x1000>, > > + <0x00a00100 0x100>; > > + interrupt-parent = <&intc>; > > + }; > > + > > + clocks { > > + #address-cells = <1>; > > + #size-cells = <0>; > > As requested by DT maintainer, please drop this container node and give an > unique name for each fixed-clock, something like: > > clock-xxx { > ... > }; > > You may want to refer to how Lucas did it for i.MX8QM. > > > + > > + ckil: clock at 0 { > > + compatible = "fixed-clock"; > > + reg = <0>; > > + #clock-cells = <0>; > > + clock-frequency = <32768>; > > + clock-output-names = "ckil"; > > + }; > > + > > + osc: clock at 1 { > > + compatible = "fixed-clock"; > > + reg = <1>; > > + #clock-cells = <0>; > > + clock-frequency = <24000000>; > > + clock-output-names = "osc"; > > + }; > > + > > + ipp_di0: clock at 2 { > > + compatible = "fixed-clock"; > > + reg = <2>; > > + #clock-cells = <0>; > > + clock-frequency = <0>; > > + clock-output-names = "ipp_di0"; > > + }; > > + > > + ipp_di1: clock at 3 { > > + compatible = "fixed-clock"; > > + reg = <3>; > > + #clock-cells = <0>; > > + clock-frequency = <0>; > > + clock-output-names = "ipp_di1"; > > + }; > > + }; > > + > > + soc { > > + #address-cells = <1>; > > + #size-cells = <1>; > > + compatible = "simple-bus"; > > + interrupt-parent = <&gpc>; > > + ranges; > > + > > + ocram: sram at 900000 { > > + compatible = "mmio-sram"; > > + reg = <0x00900000 0x20000>; > > + }; > > + > > + L2: l2-cache at a02000 { > > + compatible = "arm,pl310-cache"; > > + reg = <0x00a02000 0x1000>; > > + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; > > + cache-unified; > > + cache-level = <2>; > > + arm,tag-latency = <4 2 3>; > > + arm,data-latency = <4 2 3>; > > + }; > > + > > + aips1: aips-bus at 2000000 { > > + compatible = "fsl,aips-bus", "simple-bus"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + reg = <0x02000000 0x100000>; > > + ranges; > > + > > + spba: spba-bus at 2000000 { > > + compatible = "fsl,spba-bus", "simple-bus"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + reg = <0x02000000 0x40000>; > > + ranges; > > + > > + spdif: spdif at 2004000 { > > + compatible = "fsl,imx6sl-spdif", "fsl,imx35-spdif"; > > + reg = <0x02004000 0x4000>; > > + interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 14 18 0>, <&sdma 15 18 0>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_SPDIF_GCLK>, > > + <&clks IMX6SLL_CLK_OSC>, > > + <&clks IMX6SLL_CLK_SPDIF>, > > + <&clks IMX6SLL_CLK_DUMMY>, > > + <&clks IMX6SLL_CLK_DUMMY>, > > + <&clks IMX6SLL_CLK_DUMMY>, > > + <&clks IMX6SLL_CLK_IPG>, > > + <&clks IMX6SLL_CLK_DUMMY>, > > + <&clks IMX6SLL_CLK_DUMMY>, > > + <&clks IMX6SLL_CLK_SPBA>; > > + clock-names = "core", "rxtx0", > > + "rxtx1", "rxtx2", > > + "rxtx3", "rxtx4", > > + "rxtx5", "rxtx6", > > + "rxtx7", "dma"; > > + status = "disabled"; > > + }; > > + > > + ecspi1: ecspi at 2008000 { > > s/ecspi/spi for node name. > > > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > > + reg = <0x02008000 0x4000>; > > + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 3 7 1>, <&sdma 4 7 2>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_ECSPI1>, > > + <&clks IMX6SLL_CLK_ECSPI1>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + ecspi2: ecspi at 200c000 { > > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > > + reg = <0x0200c000 0x4000>; > > + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 5 7 1>, <&sdma 6 7 2>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_ECSPI2>, > > + <&clks IMX6SLL_CLK_ECSPI2>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + ecspi3: ecspi at 2010000 { > > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > > + reg = <0x02010000 0x4000>; > > + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 7 7 1>, <&sdma 8 7 2>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_ECSPI3>, > > + <&clks IMX6SLL_CLK_ECSPI3>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + ecspi4: ecspi at 2014000 { > > + compatible = "fsl,imx6ul-ecspi", "fsl,imx51-ecspi"; > > + reg = <0x02014000 0x4000>; > > + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 9 7 1>, <&sdma 10 7 2>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_ECSPI4>, > > + <&clks IMX6SLL_CLK_ECSPI4>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + uart4: serial at 2018000 { > > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", > "fsl,imx21-uart"; > > + reg = <0x02018000 0x4000>; > > + interrupts =<GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 31 4 0>, <&sdma 32 4 0>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_UART4_IPG>, > > + <&clks IMX6SLL_CLK_UART4_SERIAL>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + uart1: serial at 2020000 { > > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", > "fsl,imx21-uart"; > > + reg = <0x02020000 0x4000>; > > + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 25 4 0>, <&sdma 26 4 0>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_UART1_IPG>, > > + <&clks IMX6SLL_CLK_UART1_SERIAL>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + uart2: serial at 2024000 { > > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", > "fsl,imx21-uart"; > > + reg = <0x02024000 0x4000>; > > + interrupts = <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 27 4 0>, <&sdma 28 4 0>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_UART2_IPG>, > > + <&clks IMX6SLL_CLK_UART2_SERIAL>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + > > + ssi1: ssi at 2028000 { > > ssi-controller > > > + compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi"; > > + reg = <0x02028000 0x4000>; > > + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 37 22 0>, <&sdma 38 22 0>; > > + dma-names = "rx", "tx"; > > + fsl,fifo-depth = <15>; > > + clocks = <&clks IMX6SLL_CLK_SSI1_IPG>, > > + <&clks IMX6SLL_CLK_SSI1>; > > + clock-names = "ipg", "baud"; > > + status = "disabled"; > > + }; > > + > > + ssi2: ssi2 at 202c000 { > > Drop 2 from node name. > > > + compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi"; > > + reg = <0x0202c000 0x4000>; > > + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 41 22 0>, <&sdma 42 22 0>; > > + dma-names = "rx", "tx"; > > + fsl,fifo-depth = <15>; > > + clocks = <&clks IMX6SLL_CLK_SSI2_IPG>, > > + <&clks IMX6SLL_CLK_SSI2>; > > + clock-names = "ipg", "baud"; > > + status = "disabled"; > > + }; > > + > > + ssi3: ssi at 2030000 { > > + compatible = "fsl,imx6sl-ssi", "fsl,imx51-ssi"; > > + reg = <0x02030000 0x4000>; > > + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 45 22 0>, <&sdma 46 22 0>; > > + dma-names = "rx", "tx"; > > + fsl,fifo-depth = <15>; > > + clocks = <&clks IMX6SLL_CLK_SSI3_IPG>, > > + <&clks IMX6SLL_CLK_SSI3>; > > + clock-names = "ipg", "baud"; > > + status = "disabled"; > > + }; > > + > > + uart3: serial at 2034000 { > > + compatible = "fsl,imx6sl-uart", "fsl,imx6q-uart", > "fsl,imx21-uart"; > > + reg = <0x02034000 0x4000>; > > + interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 29 4 0>, <&sdma 30 4 0>; > > + dma-name = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_UART3_IPG>, > > + <&clks IMX6SLL_CLK_UART3_SERIAL>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + }; > > + > > + pwm1: pwm at 2080000 { > > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > > + reg = <0x02080000 0x4000>; > > + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_PWM1>, > > + <&clks IMX6SLL_CLK_PWM1>; > > + clock-names = "ipg", "per"; > > + #pwm-cells = <2>; > > + }; > > + > > + pwm2: pwm at 2084000 { > > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > > + reg = <0x02084000 0x4000>; > > + interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_PWM2>, > > + <&clks IMX6SLL_CLK_PWM2>; > > + clock-names = "ipg", "per"; > > + #pwm-cells = <2>; > > + }; > > + > > + pwm3: pwm at 2088000 { > > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > > + reg = <0x02088000 0x4000>; > > + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_PWM3>, > > + <&clks IMX6SLL_CLK_PWM3>; > > + clock-names = "ipg", "per"; > > + #pwm-cells = <2>; > > + }; > > + > > + pwm4: pwm at 208c000 { > > + compatible = "fsl,imx6sll-pwm", "fsl,imx27-pwm"; > > + reg = <0x0208c000 0x4000>; > > + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_PWM4>, > > + <&clks IMX6SLL_CLK_PWM4>; > > + clock-names = "ipg", "per"; > > + #pwm-cells = <2>; > > + }; > > + > > + gpt1: gpt at 2098000 { > > timer > > > + compatible = "fsl,imx6sll-gpt"; > > + reg = <0x02098000 0x4000>; > > + interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_GPT_BUS>, > > + <&clks IMX6SLL_CLK_GPT_SERIAL>; > > + clock-names = "ipg", "per"; > > + }; > > + > > + gpio1: gpio at 209c000 { > > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > > + reg = <0x0209c000 0x4000>; > > + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + }; > > + > > + gpio2: gpio at 20a0000 { > > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > > + reg = <0x020a0000 0x4000>; > > + interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + }; > > + > > + gpio3: gpio at 20a4000 { > > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > > + reg = <0x020a4000 0x4000>; > > + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + }; > > + > > + gpio4: gpio at 20a8000 { > > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > > + reg = <0x020a8000 0x4000>; > > + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + }; > > + > > + gpio5: gpio at 20ac000 { > > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > > + reg = <0x020ac000 0x4000>; > > + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + }; > > + > > + gpio6: gpio at 20b0000 { > > + compatible = "fsl,imx6sll-gpio", "fsl,imx35-gpio"; > > + reg = <0x020b0000 0x4000>; > > + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; > > + gpio-controller; > > + #gpio-cells = <2>; > > + interrupt-controller; > > + #interrupt-cells = <2>; > > + }; > > + > > + kpp: kpp at 20b8000 { > > s/kpp/keypad for node name. > > > + compatible = "fsl,imx6sll-kpp", "fsl,imx21-kpp"; > > + reg = <0x020b8000 0x4000>; > > + interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_KPP>; > > + status = "disabled"; > > + }; > > + > > + wdog1: wdog at 20bc000 { > > s/wdog/watchdog for node name. > > > + compatible = "fsl,imx6sll-wdt", "fsl,imx21-wdt"; > > + reg = <0x020bc000 0x4000>; > > + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_WDOG1>; > > + }; > > + > > + wdog2: wdog at 20c0000 { > > + compatible = "fsl,imx6sll-wdt", "fsl,imx21-wdt"; > > + reg = <0x020c0000 0x4000>; > > + interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_WDOG2>; > > + status = "disabled"; > > + }; > > + > > + clks: clock-controller at 20c4000 { > > + compatible = "fsl,imx6sll-ccm"; > > + reg = <0x020c4000 0x4000>; > > + interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>; > > + #clock-cells = <1>; > > + clocks = <&ckil>, <&osc>, <&ipp_di0>, <&ipp_di1>; > > + clock-names = "ckil", "osc", "ipp_di0", "ipp_di1"; > > + > > + assigned-clocks = <&clks IMX6SLL_CLK_PERCLK_SEL>; > > + assigned-clock-parents = <&clks IMX6SLL_CLK_OSC>; > > + }; > > + > > + anatop: anatop at 20c8000 { > > + compatible = "fsl,imx6sll-anatop", > > + "fsl,imx6q-anatop", > > + "syscon", "simple-bus"; > > + reg = <0x020c8000 0x4000>; > > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>; > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + reg_3p0: regulator-3p0 at 20c8120 { > > + compatible = "fsl,anatop-regulator"; > > + reg = <0x20c8120>; > > + regulator-name = "vdd3p0"; > > + regulator-min-microvolt = <2625000>; > > + regulator-max-microvolt = <3400000>; > > + anatop-reg-offset = <0x120>; > > + anatop-vol-bit-shift = <8>; > > + anatop-vol-bit-width = <5>; > > + anatop-min-bit-val = <0>; > > + anatop-min-voltage = <2625000>; > > + anatop-max-voltage = <3400000>; > > + anatop-enable-bit = <0>; > > + }; > > + }; > > + > > + tempmon: tempmon { > > s/tempmon/temperature-sensor for node name. > > > + compatible = "fsl,imx6sll-tempmon", "fsl,imx6sx-tempmon"; > > + interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; > > + fsl,tempmon = <&anatop>; > > + fsl,tempmon-data = <&ocotp>; > > + clocks = <&clks IMX6SLL_CLK_PLL3_USB_OTG>; > > + status = "disabled"; > > + }; > > + > > + usbphy1: usbphy at 20c9000 { > > s/usbphy/usb-phy for node name. > > > + compatible = "fsl,imx6sll-usbphy", "fsl,imx6ul-usbphy", > > + "fsl,imx23-usbphy"; > > + reg = <0x020c9000 0x1000>; > > + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USBPHY1>; > > + phy-3p0-supply = <®_3p0>; > > + fsl,anatop = <&anatop>; > > + }; > > + > > + usbphy2: usbphy at 20ca000 { > > + compatible = "fsl,imx6sll-usbphy", "fsl,imx6ul-usbphy", > > + "fsl,imx23-usbphy"; > > + reg = <0x020ca000 0x1000>; > > + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USBPHY2>; > > + phy-reg_3p0-supply = <®_3p0>; > > + fsl,anatop = <&anatop>; > > + }; > > + > > + snvs: snvs at 20cc000 { > > + compatible = "fsl,sec-v4.0-mon", "syscon", "simple-mfd"; > > + reg = <0x020cc000 0x4000>; > > + > > + snvs_rtc: snvs-rtc-lp { > > + compatible = "fsl,sec-v4.0-mon-rtc-lp"; > > + regmap = <&snvs>; > > + offset = <0x34>; > > + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>, > <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + snvs_poweroff: snvs-poweroff { > > + compatible = "syscon-poweroff"; > > + regmap = <&snvs>; > > + offset = <0x38>; > > + mask = <0x61>; > > + }; > > + > > + snvs_pwrkey: snvs-powerkey { > > + compatible = "fsl,sec-v4.0-pwrkey"; > > + regmap = <&snvs>; > > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>; > > + linux,keycode = <KEY_POWER>; > > + wakeup-source; > > + }; > > + }; > > + > > + epit1: epit at 20d0000 { > > + reg = <0x020d0000 0x4000>; > > + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > + > > + epit2: epit at 20d4000 { > > + reg = <0x020d4000 0x4000>; > > + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; > > + }; > > No compatible, so unused? > > > + > > + src: src at 20d8000 { > > reset-controller > > > + compatible = "fsl,imx6sll-src"; > > + reg = <0x020d8000 0x4000>; > > + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; > > + #reset-cells = <1>; > > + }; > > + > > + gpc: gpc at 20dc000 { > > interrupt-controller > > > + compatible = "fsl,imx6sll-gpc", "fsl,imx6q-gpc"; > > + reg = <0x020dc000 0x4000>; > > + interrupt-controller; > > + #interrupt-cells = <3>; > > + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>; > > + interrupt-parent = <&intc>; > > + fsl,mf-mix-wakeup-irq = <0x7c00000 0x7d00 0x0 > 0x1400640>; > > What is this? > > > + }; > > + > > + iomuxc: iomuxc at 20e0000 { > > + compatible = "fsl,imx6sll-iomuxc"; > > + reg = <0x020e0000 0x4000>; > > + }; > > + > > + gpr: iomuxc-gpr at 20e4000 { > > + compatible = "fsl,imx6sll-iomuxc-gpr", > > + "fsl,imx6q-iomuxc-gpr", "syscon"; > > + reg = <0x020e4000 0x4000>; > > + }; > > + > > + csi: csi at 20e8000 { > > + compatible = "fsl,imx6sll-csi", "fsl,imx6s-csi"; > > + reg = <0x020e8000 0x4000>; > > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_DUMMY>, > > + <&clks IMX6SLL_CLK_CSI>, > > + <&clks IMX6SLL_CLK_DUMMY>; > > + clock-names = "disp-axi", "csi_mclk", "disp_dcic"; > > + status = "disabled"; > > + }; > > + > > + sdma: sdma at 20ec000 { > > dma-controller > > > + compatible = "fsl,imx6sll-sdma", "fsl,imx35-sdma"; > > + reg = <0x020ec000 0x4000>; > > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_SDMA>, > > + <&clks IMX6SLL_CLK_SDMA>; > > + clock-names = "ipg", "ahb"; > > + #dma-cells = <3>; > > + iram = <&ocram>; > > + fsl,sdma-ram-script-name = "imx/sdma/sdma-imx6q.bin"; > > + }; > > + > > + lcdif: lcdif at 20f8000 { > > lcd-controller > > > + compatible = "fsl,imx6sll-lcdif", "fsl,imx28-lcdif"; > > + reg = <0x020f8000 0x4000>; > > + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_LCDIF_PIX>, > > + <&clks IMX6SLL_CLK_LCDIF_APB>, > > + <&clks IMX6SLL_CLK_DUMMY>; > > + clock-names = "pix", "axi", "disp_axi"; > > + status = "disabled"; > > + }; > > + > > + dcp: dcp at 20fc000 { > > + compatible = "fsl,imx6sl-dcp"; > > + reg = <0x020fc000 0x4000>; > > + interrupts = <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_DCP>; > > + clock-names = "dcp"; > > + }; > > + }; > > + > > + aips2: aips-bus at 2100000 { > > + compatible = "fsl,aips-bus", "simple-bus"; > > + #address-cells = <1>; > > + #size-cells = <1>; > > + reg = <0x02100000 0x100000>; > > + ranges; > > + > > + usbotg1: usb at 2184000 { > > + compatible = "fsl,imx6sll-usb", "fsl,imx6ul-usb", > > + "fsl,imx27-usb"; > > + reg = <0x02184000 0x200>; > > + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USBOH3>; > > + fsl,usbphy = <&usbphy1>; > > + fsl,usbmisc = <&usbmisc 0>; > > + fsl,anatop = <&anatop>; > > + ahb-burst-config = <0x0>; > > + tx-burst-size-dword = <0x10>; > > + rx-burst-size-dword = <0x10>; > > + status = "disabled"; > > + }; > > + > > + usbotg2: usb at 2184200 { > > + compatible = "fsl,imx6sll-usb", "fsl,imx6ul-usb", > > + "fsl,imx27-usb"; > > + reg = <0x02184200 0x200>; > > + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USBOH3>; > > + fsl,usbphy = <&usbphy2>; > > + fsl,usbmisc = <&usbmisc 1>; > > + ahb-burst-config = <0x0>; > > + tx-burst-size-dword = <0x10>; > > + rx-burst-size-dword = <0x10>; > > + status = "disabled"; > > + }; > > + > > + usbmisc: usbmisc at 2184800 { > > + #index-cells = <1>; > > + compatible = "fsl,imx6sll-usbmisc", "fsl,imx6ul-usbmisc", > > + "fsl,imx6q-usbmisc"; > > + reg = <0x02184800 0x200>; > > + }; > > + > > + usdhc1: usdhc at 2190000 { > > s/usdhc/mmc for node name. > > > + compatible = "fsl,imx6sll-usdhc", "fsl,imx6sx-usdhc"; > > + reg = <0x02190000 0x4000>; > > + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USDHC1>, > > + <&clks IMX6SLL_CLK_USDHC1>, > > + <&clks IMX6SLL_CLK_USDHC1>; > > + clock-names = "ipg", "ahb", "per"; > > + bus-width = <4>; > > + fsl,tuning-step = <2>; > > + fsl,tuning-start-tap = <20>; > > + status = "disabled"; > > + }; > > + > > + usdhc2: usdhc at 2194000 { > > + compatible = "fsl,imx6sll-usdhc", "fsl,imx6sx-usdhc"; > > + reg = <0x02194000 0x4000>; > > + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USDHC2>, > > + <&clks IMX6SLL_CLK_USDHC2>, > > + <&clks IMX6SLL_CLK_USDHC2>; > > + clock-names = "ipg", "ahb", "per"; > > + bus-width = <4>; > > + fsl,tuning-step = <2>; > > + fsl,tuning-start-tap = <20>; > > + status = "disabled"; > > + }; > > + > > + usdhc3: usdhc at 2198000 { > > + compatible = "fsl,imx6sll-usdhc", "fsl,imx6sx-usdhc"; > > + reg = <0x02198000 0x4000>; > > + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_USDHC3>, > > + <&clks IMX6SLL_CLK_USDHC3>, > > + <&clks IMX6SLL_CLK_USDHC3>; > > + clock-names = "ipg", "ahb", "per"; > > + bus-width = <4>; > > + fsl,tuning-step = <2>; > > + fsl,tuning-start-tap = <20>; > > + status = "disabled"; > > + }; > > + > > + i2c1: i2c at 21a0000 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + compatible = "fs,imx6sll-i2c", "fsl,imx21-i2c"; > > + reg = <0x021a0000 0x4000>; > > + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_I2C1>; > > + status = "disabled"; > > + }; > > + > > + i2c2: i2c at 21a4000 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + compatible = "fsl,imx6sll-i2c", "fsl,imx21-i2c"; > > + reg = <0x021a4000 0x4000>; > > + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_I2C2>; > > + status = "disabled"; > > + }; > > + > > + i2c3: i2c at 21a8000 { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + compatible = "fsl,imx6sll-i2c", "fsl,imx21-i2c"; > > + reg = <0x021a8000 0x4000>; > > + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_I2C3>; > > + status = "disabled"; > > + }; > > + > > + romcp at 21ac000 { > > + compatible = "fsl,imx6sll-romcp", "syscon"; > > + reg = <0x021ac000 0x4000>; > > + }; > > + > > + mmdc: mmdc at 21b0000 { > > memory-controller > > Shawn > > > + compatible = "fsl,imx6sll-mmdc", "fsl,imx6q-mmdc"; > > + reg = <0x021b0000 0x4000>; > > + }; > > + > > + rngb: rngb at 21b4000 { > > + reg = <0x021b4000 0x4000>; > > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6SLL_CLK_DUMMY>; > > + }; > > + > > + ocotp: ocotp-ctrl at 21bc000 { > > + compatible = "fsl,imx6sll-ocotp", "syscon"; > > + reg = <0x021bc000 0x4000>; > > + clocks = <&clks IMX6SLL_CLK_OCOTP>; > > + }; > > + > > + snvs_gpr: snvs-gpr at 21c4000 { > > + reg = <0x021c4000 0x10000>; > > + }; > > + > > + iomuxc_snvs: iomuxc-snvs at 21c8000 { > > + reg = <0x021c8000 0x10000>; > > + }; > > + > > + audmux: audmux at 21d8000 { > > + compatible = "fsl,imx6sll-audmux", "fsl,imx31-audmux"; > > + reg = <0x021d8000 0x4000>; > > + status = "disabled"; > > + }; > > + > > + uart5: serial at 21f4000 { > > + compatible = "fsl,imx6sll-uart", "fsl,imx6q-uart", > "fsl,imx21-uart"; > > + reg = <0x021f4000 0x4000>; > > + interrupts =<GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; > > + dmas = <&sdma 33 4 0>, <&sdma 34 4 0>; > > + dma-names = "rx", "tx"; > > + clocks = <&clks IMX6SLL_CLK_UART5_IPG>, > > + <&clks IMX6SLL_CLK_UART5_SERIAL>; > > + clock-names = "ipg", "per"; > > + status = "disabled"; > > + }; > > + }; > > + }; > > +}; > > -- > > 1.9.1 > > ^ permalink raw reply [flat|nested] 10+ messages in thread
[parent not found: <20180309233931.7xujvo4eg4g5ftri@rob-hp-laptop>]
* [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll [not found] ` <20180309233931.7xujvo4eg4g5ftri@rob-hp-laptop> @ 2018-03-12 4:43 ` Jacky Bai 2018-03-16 15:40 ` Rob Herring 0 siblings, 1 reply; 10+ messages in thread From: Jacky Bai @ 2018-03-12 4:43 UTC (permalink / raw) To: linux-arm-kernel > > diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi > > + spi3 = &ecspi3; > > + spi4 = &ecspi4; > > + usbphy0 = &usbphy1; > > + usbphy1 = &usbphy2; > > Why do you need a alias for phys? The alias of usbphy seems used by drivers/usb/phy/phy-mxs-usb.c. So we need to add alias for usbphy. > > > + }; > > + > > + cpus { > > + #address-cells = <1>; > > + #size-cells = <0>; > > + > > + cpu0: cpu at 0 { > > + compatible = "arm,cortex-a9"; > > + device_type = "cpu"; > > + reg = <0>; > > + next-level-cache = <&L2>; > > + operating-points = < > > + /* kHz uV */ > > + 996000 1225000 > > + 792000 1175000 > > + 396000 1075000 > > + 198000 975000 > > + >; > > + fsl,soc-operating-points = < > > This is not documented. This is same as we used on other imx6 SOC. I don't know where to add doc for this property. Please give me some suggestion. BR Jacky Bai > > > + /* ARM kHz SOC-PU uV */ > > + 996000 1225000 > > + 792000 1175000 > > + 396000 1175000 > > + 198000 1175000 > > + >; > > + clock-latency = <61036>; /* two CLK32 periods */ > > + fsl,low-power-run; ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll 2018-03-12 4:43 ` Jacky Bai @ 2018-03-16 15:40 ` Rob Herring 2018-03-19 1:40 ` Jacky Bai 0 siblings, 1 reply; 10+ messages in thread From: Rob Herring @ 2018-03-16 15:40 UTC (permalink / raw) To: linux-arm-kernel On Sun, Mar 11, 2018 at 11:43 PM, Jacky Bai <ping.bai@nxp.com> wrote: >> > diff --git a/arch/arm/boot/dts/imx6sll.dtsi b/arch/arm/boot/dts/imx6sll.dtsi >> > + spi3 = &ecspi3; >> > + spi4 = &ecspi4; >> > + usbphy0 = &usbphy1; >> > + usbphy1 = &usbphy2; >> >> Why do you need a alias for phys? > > The alias of usbphy seems used by drivers/usb/phy/phy-mxs-usb.c. So we need to add alias for usbphy. That use should be fixed. The correct way to handle this is add a cell to "fsl,anatop" with 0 or 1 to distinguish each phy. >> > + }; >> > + >> > + cpus { >> > + #address-cells = <1>; >> > + #size-cells = <0>; >> > + >> > + cpu0: cpu at 0 { >> > + compatible = "arm,cortex-a9"; >> > + device_type = "cpu"; >> > + reg = <0>; >> > + next-level-cache = <&L2>; >> > + operating-points = < >> > + /* kHz uV */ >> > + 996000 1225000 >> > + 792000 1175000 >> > + 396000 1075000 >> > + 198000 975000 >> > + >; >> > + fsl,soc-operating-points = < >> >> This is not documented. > > This is same as we used on other imx6 SOC. I don't know where to add doc for this property. Please give me some suggestion. Along side other OPP binding docs. The real question is why you need this and can't use the original OPP binding (which you have too) or move to the v2 binding. Rob ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll 2018-03-16 15:40 ` Rob Herring @ 2018-03-19 1:40 ` Jacky Bai 0 siblings, 0 replies; 10+ messages in thread From: Jacky Bai @ 2018-03-19 1:40 UTC (permalink / raw) To: linux-arm-kernel > Subject: Re: [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll > > On Sun, Mar 11, 2018 at 11:43 PM, Jacky Bai <ping.bai@nxp.com> wrote: > >> > diff --git a/arch/arm/boot/dts/imx6sll.dtsi > >> > b/arch/arm/boot/dts/imx6sll.dtsi > >> > + spi3 = &ecspi3; > >> > + spi4 = &ecspi4; > >> > + usbphy0 = &usbphy1; > >> > + usbphy1 = &usbphy2; > >> > >> Why do you need a alias for phys? > > > > The alias of usbphy seems used by drivers/usb/phy/phy-mxs-usb.c. So we need > to add alias for usbphy. > > That use should be fixed. The correct way to handle this is add a cell to > "fsl,anatop" with 0 or 1 to distinguish each phy. > This change can be done later by usb guys, for now I think it can be just keep as other imx6 platform. > >> > + }; > >> > + > >> > + cpus { > >> > + #address-cells = <1>; > >> > + #size-cells = <0>; > >> > + > >> > + cpu0: cpu at 0 { > >> > + compatible = "arm,cortex-a9"; > >> > + device_type = "cpu"; > >> > + reg = <0>; > >> > + next-level-cache = <&L2>; > >> > + operating-points = < > >> > + /* kHz uV */ > >> > + 996000 1225000 > >> > + 792000 1175000 > >> > + 396000 1075000 > >> > + 198000 975000 > >> > + >; > >> > + fsl,soc-operating-points = < > >> > >> This is not documented. > > > > This is same as we used on other imx6 SOC. I don't know where to add doc for > this property. Please give me some suggestion. > > Along side other OPP binding docs. The real question is why you need this and > can't use the original OPP binding (which you have too) or move to the v2 > binding. > For i.MX6 SOCs, we have CPU core voltage domain and a SOC voltage domain. The voltage of these two domain has strict relationship. So when doing cpu core DVFS, the SOC voltage need to be changed accordingly, the 'fsl,soc-operating-points' binding is used for SOC OPP. Jacky > Rob ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2018-03-19 1:40 UTC | newest]
Thread overview: 10+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1520503424-22985-1-git-send-email-ping.bai@nxp.com>
2018-03-08 10:03 ` [PATCH v4 2/2] ARM: dts: imx: Add basic dts support for imx6sll EVK board Bai Ping
2018-03-08 15:35 ` Fabio Estevam
2018-03-09 3:36 ` Shawn Guo
2018-03-09 5:06 ` Jacky Bai
2018-03-09 23:44 ` Rob Herring
2018-03-09 3:15 ` [PATCH v4 1/2] ARM: dts: imx: Add basic dtsi file for imx6sll Shawn Guo
2018-03-09 5:04 ` Jacky Bai
[not found] ` <20180309233931.7xujvo4eg4g5ftri@rob-hp-laptop>
2018-03-12 4:43 ` Jacky Bai
2018-03-16 15:40 ` Rob Herring
2018-03-19 1:40 ` Jacky Bai
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).