[PATCH 21/52] mtd: rawnand: jz4780: convert driver to nand_scan()

[miquel.raynal@bootlin.com (Miquel Raynal)]

Hi Harvey,

On Fri, 16 Mar 2018 15:33:05 +0000, Harvey Hunt
<harveyhuntnexus@gmail.com> wrote:

> Hi Miqu?l,
> 
> On 03/16/2018 01:38 PM, Miquel Raynal wrote:
> > Hi Harvey,
> > 
> > On Thu, 15 Mar 2018 15:40:25 +0000, Harvey Hunt
> > <harveyhuntnexus@gmail.com> wrote:
> >   
> >> Hi Miquel,
> >>
> >> Sorry it's taken me a little while to review your changes, a few
> >> comments below:
> >>
> >> On 03/02/2018 05:03 PM, Miquel Raynal wrote:  
> >>> Two helpers have been added to the core to make ECC-related
> >>> configuration between the detection phase and the final NAND scan. Use
> >>> these hooks and convert the driver to just use nand_scan() instead of
> >>> both nand_scan_ident() and nand_scan_tail().
> >>>
> >>> Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
> >>> ---
> >>>  drivers/mtd/nand/raw/jz4780_nand.c | 30 ++++++++++++------------------
> >>>  1 file changed, 12 insertions(+), 18 deletions(-)
> >>>
> >>> diff --git a/drivers/mtd/nand/raw/jz4780_nand.c b/drivers/mtd/nand/raw/jz4780_nand.c
> >>> index e69f6ae4c539..fd5dc9d9b0c6 100644
> >>> --- a/drivers/mtd/nand/raw/jz4780_nand.c
> >>> +++ b/drivers/mtd/nand/raw/jz4780_nand.c
> >>> @@ -157,9 +157,8 @@ static int jz4780_nand_ecc_correct(struct mtd_info *mtd, u8 *dat,
> >>>  	return jz4780_bch_correct(nfc->bch, &params, dat, read_ecc);
> >>>  }
> >>>  
> >>> -static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *dev)
> >>> +static int jz4780_nand_attach_chip(struct nand_chip *chip)
> >>>  {
> >>> -	struct nand_chip *chip = &nand->chip;
> >>>  	struct mtd_info *mtd = nand_to_mtd(chip);
> >>>  	struct jz4780_nand_controller *nfc = to_jz4780_nand_controller(chip->controller);
> >>>  	int eccbytes;
> >>> @@ -170,7 +169,8 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
> >>>  	switch (chip->ecc.mode) {
> >>>  	case NAND_ECC_HW:
> >>>  		if (!nfc->bch) {
> >>> -			dev_err(dev, "HW BCH selected, but BCH controller not found\n");
> >>> +			dev_err(nfc->dev,
> >>> +				"HW BCH selected, but BCH controller not found\n");
> >>>  			return -ENODEV;
> >>>  		}
> >>>  
> >>> @@ -179,15 +179,16 @@ static int jz4780_nand_init_ecc(struct jz4780_nand_chip *nand, struct device *de
> >>>  		chip->ecc.correct = jz4780_nand_ecc_correct;
> >>>  		/* fall through */
> >>>  	case NAND_ECC_SOFT:
> >>> -		dev_info(dev, "using %s (strength %d, size %d, bytes %d)\n",
> >>> -			(nfc->bch) ? "hardware BCH" : "software ECC",
> >>> -			chip->ecc.strength, chip->ecc.size, chip->ecc.bytes);
> >>> +		dev_info(nfc->dev, "using %s (strength %d, size %d, bytes %d)\n",
> >>> +			 (nfc->bch) ? "hardware BCH" : "software ECC",
> >>> +			 chip->ecc.strength, chip->ecc.size, chip->ecc.bytes)>  		break;
> >>>  	case NAND_ECC_NONE:
> >>> -		dev_info(dev, "not using ECC\n");
> >>> +		dev_info(nfc->dev, "not using ECC\n");
> >>>  		break;
> >>>  	default:
> >>> -		dev_err(dev, "ECC mode %d not supported\n", chip->ecc.mode);
> >>> +		dev_err(nfc->dev, "ECC mode %d not supported\n",
> >>> +			chip->ecc.mode);
> >>>  		return -EINVAL;
> >>>  	}    
> >> These changes seem redundant as dev is passed into the function,
> >> although you could remove it from the function defintion.  
> > 
> > That is right, I should have also removed the 'dev' parameter.
> >   
> 
> That'd be great

Actually there is nothing to do, the new prototype is already:

    static int jz4780_nand_attach_chip(struct nand_chip *chip);

which doesn't have the *dev parameter anymore :-)

Thanks anyway for reviewing!
Miqu?l

-- 
Miquel Raynal, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com