From mboxrd@z Thu Jan  1 00:00:00 1970
From: bjorn.andersson@linaro.org (Bjorn Andersson)
Date: Tue, 27 Mar 2018 10:49:13 -0700
Subject: [PATCH v5 13/13] ARM: dts: ipq8074: Enable few peripherals for
 hk01 board
In-Reply-To: <1521800336-19266-14-git-send-email-sricharan@codeaurora.org>
References: <1521800336-19266-1-git-send-email-sricharan@codeaurora.org>
 <1521800336-19266-14-git-send-email-sricharan@codeaurora.org>
Message-ID: <20180327174913.GP1403@tuxbook-pro>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On Fri 23 Mar 03:18 PDT 2018, Sricharan R wrote:

> Reviewed-by: Abhishek Sahu <absahu@codeaurora.org>
> Signed-off-by: Sricharan R <sricharan@codeaurora.org>
> ---
>  arch/arm64/boot/dts/qcom/ipq8074-hk01.dts | 103 ++++++++++++++++++++++++++++++
>  1 file changed, 103 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
> index 6a838b5..dbca7ec 100644
> --- a/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
> +++ b/arch/arm64/boot/dts/qcom/ipq8074-hk01.dts
> @@ -21,6 +21,7 @@
>  
>  	aliases {
>  		serial0 = &blsp1_uart5;
> +		serial1 = &serial_blsp2;
>  	};
>  
>  	chosen {
> @@ -41,6 +42,47 @@
>  					bias-disable;
>  				};
>  			};
> +
> +			 i2c_0_pins: i2c_0_pinmux {
> +				  mux {
> +					   pins = "gpio42", "gpio43";
> +					   function = "blsp1_i2c";
> +					   drive-strength = <8>;
> +					   bias-disable;
> +				  };
> +			 };
> +
> +			 spi_0_pins: spi_0_pins {
> +				  mux {
> +					   pins = "gpio38", "gpio39", "gpio40", "gpio41";
> +					   function = "blsp0_spi";
> +					   drive-strength = <8>;
> +					   bias-disable;
> +				  };
> +			 };
> +
> +			 hsuart_pins: hsuart_pins {
> +				  mux {
> +					   pins = "gpio46", "gpio47", "gpio48", "gpio49";
> +					   function = "blsp2_uart";
> +					   drive-strength = <8>;
> +					   bias-disable;
> +				  };
> +			 };
> +
> +			 qpic_pins: qpic_pins {
> +				mux {
> +					   pins = "gpio1", "gpio3", "gpio4",
> +						  "gpio5", "gpio6", "gpio7",
> +						  "gpio8", "gpio10", "gpio11",
> +						  "gpio12", "gpio13", "gpio14",
> +						  "gpio15", "gpio16", "gpio17";
> +					   function = "qpic";

I would prefer that you move the pinmux part to the same dtsi that
defines the nand and add the board specific pinconf (electrical
properties) here. That way we limit the repetition between the board
files.

> +					   drive-strength = <8>;
> +					   bias-disable;
> +				  };
> +			};
> +
>  		};
>  

Other than that,

Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Regards,
Bjorn