* [PATCH V2] ARM: DTS: da850-evm: use phandles to extend nodes
@ 2018-04-27 9:47 Adam Ford
2018-05-01 10:57 ` Sekhar Nori
0 siblings, 1 reply; 2+ messages in thread
From: Adam Ford @ 2018-04-27 9:47 UTC (permalink / raw)
To: linux-arm-kernel
Many node labels in the device tree (like serial0, serial1, etc) are being
redefined, so let's modernize the device tree by using phandles to
extend the existing nodes. This helps reduce the whitespace.
Signed-off-by: Adam Ford <aford173@gmail.com>
---
V2: Rename subject per feedback from Sekhar.
Extend notes from tps6507x
Add empty line after each node
arch/arm/boot/dts/da850-evm.dts | 370 ++++++++++++++++----------------
1 file changed, 188 insertions(+), 182 deletions(-)
diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index a56d43d53ba1..52ffe6c517e3 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -27,146 +27,6 @@
spi0 = &spi1;
};
- soc at 1c00000 {
- pmx_core: pinmux at 14120 {
- status = "okay";
-
- mcasp0_pins: pinmux_mcasp0_pins {
- pinctrl-single,bits = <
- /*
- * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
- * AFSR, AMUTE
- */
- 0x00 0x11111111 0xffffffff
- /* AXR11, AXR12 */
- 0x04 0x00011000 0x000ff000
- >;
- };
- nand_pins: nand_pins {
- pinctrl-single,bits = <
- /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
- 0x1c 0x10110110 0xf0ff0ff0
- /*
- * EMA_D[0], EMA_D[1], EMA_D[2],
- * EMA_D[3], EMA_D[4], EMA_D[5],
- * EMA_D[6], EMA_D[7]
- */
- 0x24 0x11111111 0xffffffff
- /* EMA_A[1], EMA_A[2] */
- 0x30 0x01100000 0x0ff00000
- >;
- };
- };
- serial0: serial at 42000 {
- status = "okay";
- };
- serial1: serial at 10c000 {
- status = "okay";
- };
- serial2: serial at 10d000 {
- status = "okay";
- };
- rtc0: rtc at 23000 {
- status = "okay";
- };
- i2c0: i2c at 22000 {
- status = "okay";
- clock-frequency = <100000>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
-
- tps: tps at 48 {
- reg = <0x48>;
- };
- tlv320aic3106: tlv320aic3106 at 18 {
- #sound-dai-cells = <0>;
- compatible = "ti,tlv320aic3106";
- reg = <0x18>;
- status = "okay";
-
- /* Regulators */
- IOVDD-supply = <&vdcdc2_reg>;
- /* Derived from VBAT: Baseboard 3.3V / 1.8V */
- AVDD-supply = <&vbat>;
- DRVDD-supply = <&vbat>;
- DVDD-supply = <&vbat>;
- };
- tca6416: gpio at 20 {
- compatible = "ti,tca6416";
- reg = <0x20>;
- gpio-controller;
- #gpio-cells = <2>;
- };
- };
- wdt: wdt at 21000 {
- status = "okay";
- };
- mmc0: mmc at 40000 {
- max-frequency = <50000000>;
- bus-width = <4>;
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins>;
- cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>;
- wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>;
- };
- spi1: spi at 30e000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
- flash: m25p80 at 0 {
- #address-cells = <1>;
- #size-cells = <1>;
- compatible = "m25p64";
- spi-max-frequency = <30000000>;
- m25p,fast-read;
- reg = <0>;
- partition at 0 {
- label = "U-Boot-SPL";
- reg = <0x00000000 0x00010000>;
- read-only;
- };
- partition at 1 {
- label = "U-Boot";
- reg = <0x00010000 0x00080000>;
- read-only;
- };
- partition at 2 {
- label = "U-Boot-Env";
- reg = <0x00090000 0x00010000>;
- read-only;
- };
- partition at 3 {
- label = "Kernel";
- reg = <0x000a0000 0x00280000>;
- };
- partition at 4 {
- label = "Filesystem";
- reg = <0x00320000 0x00400000>;
- };
- partition at 5 {
- label = "MAC-Address";
- reg = <0x007f0000 0x00010000>;
- read-only;
- };
- };
- };
- mdio: mdio at 224000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mdio_pins>;
- bus_freq = <2200000>;
- };
- eth0: ethernet at 220000 {
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&mii_pins>;
- };
- gpio: gpio at 226000 {
- status = "okay";
- };
- };
-
backlight {
compatible = "gpio-backlight";
enable-gpios = <&gpio 48 GPIO_ACTIVE_HIGH>;
@@ -257,61 +117,207 @@
};
};
-/include/ "tps6507x.dtsi"
+&pmx_core {
+ status = "okay";
-&tps {
- vdcdc1_2-supply = <&vbat>;
- vdcdc3-supply = <&vbat>;
- vldo1_2-supply = <&vbat>;
+ mcasp0_pins: pinmux_mcasp0_pins {
+ pinctrl-single,bits = <
+ /*
+ * AHCLKX, ACLKX, AFSX, AHCLKR, ACLKR,
+ * AFSR, AMUTE
+ */
+ 0x00 0x11111111 0xffffffff
+ /* AXR11, AXR12 */
+ 0x04 0x00011000 0x000ff000
+ >;
+ };
- regulators {
- vdcdc1_reg: regulator at 0 {
- regulator-name = "VDCDC1_3.3V";
- regulator-min-microvolt = <3150000>;
- regulator-max-microvolt = <3450000>;
- regulator-always-on;
- regulator-boot-on;
- };
+ nand_pins: nand_pins {
+ pinctrl-single,bits = <
+ /* EMA_WAIT[0], EMA_OE, EMA_WE, EMA_CS[4], EMA_CS[3] */
+ 0x1c 0x10110110 0xf0ff0ff0
+ /*
+ * EMA_D[0], EMA_D[1], EMA_D[2],
+ * EMA_D[3], EMA_D[4], EMA_D[5],
+ * EMA_D[6], EMA_D[7]
+ */
+ 0x24 0x11111111 0xffffffff
+ /* EMA_A[1], EMA_A[2] */
+ 0x30 0x01100000 0x0ff00000
+ >;
+ };
+};
- vdcdc2_reg: regulator at 1 {
- regulator-name = "VDCDC2_3.3V";
- regulator-min-microvolt = <1710000>;
- regulator-max-microvolt = <3450000>;
- regulator-always-on;
- regulator-boot-on;
- ti,defdcdc_default = <1>;
- };
+&serial0 {
+ status = "okay";
+};
- vdcdc3_reg: regulator at 2 {
- regulator-name = "VDCDC3_1.2V";
- regulator-min-microvolt = <950000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-boot-on;
- ti,defdcdc_default = <1>;
- };
+&serial1 {
+ status = "okay";
+};
- ldo1_reg: regulator at 3 {
- regulator-name = "LDO1_1.8V";
- regulator-min-microvolt = <1710000>;
- regulator-max-microvolt = <1890000>;
- regulator-always-on;
- regulator-boot-on;
- };
+&serial2 {
+ status = "okay";
+};
+
+&rtc0 {
+ status = "okay";
+};
- ldo2_reg: regulator at 4 {
- regulator-name = "LDO2_1.2V";
- regulator-min-microvolt = <1140000>;
- regulator-max-microvolt = <1320000>;
- regulator-always-on;
- regulator-boot-on;
+&i2c0 {
+ status = "okay";
+ clock-frequency = <100000>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+
+ tps: tps at 48 {
+ reg = <0x48>;
+ };
+
+ tlv320aic3106: tlv320aic3106 at 18 {
+ #sound-dai-cells = <0>;
+ compatible = "ti,tlv320aic3106";
+ reg = <0x18>;
+ status = "okay";
+
+ /* Regulators */
+ IOVDD-supply = <&vdcdc2_reg>;
+ /* Derived from VBAT: Baseboard 3.3V / 1.8V */
+ AVDD-supply = <&vbat>;
+ DRVDD-supply = <&vbat>;
+ DVDD-supply = <&vbat>;
+ };
+
+ tca6416: gpio at 20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+};
+
+&wdt {
+ status = "okay";
+};
+
+&mmc0 {
+ max-frequency = <50000000>;
+ bus-width = <4>;
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins>;
+ cd-gpios = <&gpio 64 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio 65 GPIO_ACTIVE_HIGH>;
+};
+
+&spi1 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins &spi1_cs0_pin>;
+ flash: m25p80 at 0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "m25p64";
+ spi-max-frequency = <30000000>;
+ m25p,fast-read;
+ reg = <0>;
+ partition at 0 {
+ label = "U-Boot-SPL";
+ reg = <0x00000000 0x00010000>;
+ read-only;
+ };
+ partition at 1 {
+ label = "U-Boot";
+ reg = <0x00010000 0x00080000>;
+ read-only;
+ };
+ partition at 2 {
+ label = "U-Boot-Env";
+ reg = <0x00090000 0x00010000>;
+ read-only;
+ };
+ partition at 3 {
+ label = "Kernel";
+ reg = <0x000a0000 0x00280000>;
+ };
+ partition at 4 {
+ label = "Filesystem";
+ reg = <0x00320000 0x00400000>;
+ };
+ partition at 5 {
+ label = "MAC-Address";
+ reg = <0x007f0000 0x00010000>;
+ read-only;
};
};
+};
+
+&mdio {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mdio_pins>;
+ bus_freq = <2200000>;
+};
+ð0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&mii_pins>;
+};
+
+/include/ "tps6507x.dtsi"
+
+&tps {
+ vdcdc1_2-supply = <&vbat>;
+ vdcdc3-supply = <&vbat>;
+ vldo1_2-supply = <&vbat>;
+};
+
+&vdcdc1_reg {
+ regulator-name = "VDCDC1_3.3V";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3450000>;
+ regulator-always-on;
+ regulator-boot-on;
+
touchscreen {
ti,min-pressure = <0x30>;
};
};
+&vdcdc2_reg {
+ regulator-name = "VDCDC2_3.3V";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <3450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,defdcdc_default = <1>;
+};
+
+&vdcdc3_reg {
+ regulator-name = "VDCDC3_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,defdcdc_default = <1>;
+};
+
+&ldo1_reg {
+ regulator-name = "LDO1_1.8V";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-always-on;
+ regulator-boot-on;
+};
+
+&ldo2_reg {
+ regulator-name = "LDO2_1.2V";
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-always-on;
+ regulator-boot-on;
+};
+
&gpio {
status = "okay";
};
--
2.17.0
^ permalink raw reply related [flat|nested] 2+ messages in thread
end of thread, other threads:[~2018-05-01 10:57 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2018-04-27 9:47 [PATCH V2] ARM: DTS: da850-evm: use phandles to extend nodes Adam Ford
2018-05-01 10:57 ` Sekhar Nori
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).