From: antoine.tenart@bootlin.com (Antoine Tenart)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH net-next v2 09/13] net: mvpp2: 2500baseX support
Date: Fri, 4 May 2018 15:56:39 +0200 [thread overview]
Message-ID: <20180504135643.23466-10-antoine.tenart@bootlin.com> (raw)
In-Reply-To: <20180504135643.23466-1-antoine.tenart@bootlin.com>
This patch adds the 2500Base-X PHY mode support in the Marvell PPv2
driver. 2500Base-X is quite close to 1000Base-X and SGMII modes and uses
nearly the same code path.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
---
drivers/net/ethernet/marvell/mvpp2.c | 51 +++++++++++++++++++++-------
1 file changed, 39 insertions(+), 12 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 4775ab56075e..ec061d971b1c 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -4870,6 +4870,7 @@ static int mvpp22_gop_init(struct mvpp2_port *port)
break;
case PHY_INTERFACE_MODE_SGMII:
case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
mvpp22_gop_init_sgmii(port);
break;
case PHY_INTERFACE_MODE_10GKR:
@@ -4908,7 +4909,8 @@ static void mvpp22_gop_unmask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
/* Enable the GMAC link status irq for this port */
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val |= MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
@@ -4939,7 +4941,8 @@ static void mvpp22_gop_mask_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_SUM_MASK);
val &= ~MVPP22_GMAC_INT_SUM_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_SUM_MASK);
@@ -4952,7 +4955,8 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_MASK);
val |= MVPP22_GMAC_INT_MASK_LINK_STAT;
writel(val, port->base + MVPP22_GMAC_INT_MASK);
@@ -4967,6 +4971,16 @@ static void mvpp22_gop_setup_irq(struct mvpp2_port *port)
mvpp22_gop_unmask_irq(port);
}
+/* Sets the PHY mode of the COMPHY (which configures the serdes lanes).
+ *
+ * The PHY mode used by the PPv2 driver comes from the network subsystem, while
+ * the one given to the COMPHY comes from the generic PHY subsystem. Hence they
+ * differ.
+ *
+ * The COMPHY configures the serdes lanes regardless of the actual use of the
+ * lanes by the physical layer. This is why configurations like
+ * "PPv2 (2500BaseX) - COMPHY (2500SGMII)" are valid.
+ */
static int mvpp22_comphy_init(struct mvpp2_port *port)
{
enum phy_mode mode;
@@ -4980,6 +4994,9 @@ static int mvpp22_comphy_init(struct mvpp2_port *port)
case PHY_INTERFACE_MODE_1000BASEX:
mode = PHY_MODE_SGMII;
break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ mode = PHY_MODE_2500SGMII;
+ break;
case PHY_INTERFACE_MODE_10GKR:
mode = PHY_MODE_10GKR;
break;
@@ -5058,7 +5075,8 @@ static void mvpp2_port_loopback_set(struct mvpp2_port *port,
val &= ~MVPP2_GMAC_GMII_LB_EN_MASK;
if (port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX)
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX)
val |= MVPP2_GMAC_PCS_LB_EN_MASK;
else
val &= ~MVPP2_GMAC_PCS_LB_EN_MASK;
@@ -6269,7 +6287,8 @@ static irqreturn_t mvpp2_link_status_isr(int irq, void *dev_id)
}
} else if (phy_interface_mode_is_rgmii(port->phy_interface) ||
port->phy_interface == PHY_INTERFACE_MODE_SGMII ||
- port->phy_interface == PHY_INTERFACE_MODE_1000BASEX) {
+ port->phy_interface == PHY_INTERFACE_MODE_1000BASEX ||
+ port->phy_interface == PHY_INTERFACE_MODE_2500BASEX) {
val = readl(port->base + MVPP22_GMAC_INT_STAT);
if (val & MVPP22_GMAC_INT_STAT_LINK) {
event = true;
@@ -8053,8 +8072,10 @@ static void mvpp2_phylink_validate(struct net_device *dev,
phylink_set(mask, 10000baseT_Full);
/* Fall-through */
case PHY_INTERFACE_MODE_1000BASEX:
+ case PHY_INTERFACE_MODE_2500BASEX:
phylink_set(mask, 1000baseT_Full);
phylink_set(mask, 1000baseX_Full);
+ phylink_set(mask, 2500baseX_Full);
}
bitmap_and(supported, supported, mask, __ETHTOOL_LINK_MODE_MASK_NBITS);
@@ -8097,6 +8118,9 @@ static void mvpp2_gmac_link_state(struct mvpp2_port *port,
case PHY_INTERFACE_MODE_1000BASEX:
state->speed = SPEED_1000;
break;
+ case PHY_INTERFACE_MODE_2500BASEX:
+ state->speed = SPEED_2500;
+ break;
default:
if (val & MVPP2_GMAC_STATUS0_GMII_SPEED)
state->speed = SPEED_1000;
@@ -8195,11 +8219,12 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
ctrl0 &= ~MVPP2_GMAC_PORT_TYPE_MASK;
ctrl2 &= ~(MVPP2_GMAC_PORT_RESET_MASK | MVPP2_GMAC_PCS_ENABLE_MASK);
- if (state->interface == PHY_INTERFACE_MODE_1000BASEX) {
- /* 1000BaseX port cannot negotiate speed nor can it negotiate
- * duplex: they are always operating with a fixed speed of
- * 1000Mbps in full duplex, so force 1000 speed and full duplex
- * here.
+ if (state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+ state->interface == PHY_INTERFACE_MODE_2500BASEX) {
+ /* 1000BaseX and 2500BaseX ports cannot negotiate speed nor can
+ * they negotiate duplex: they are always operating with a fixed
+ * speed of 1000/2500Mbps in full duplex, so force 1000/2500
+ * speed and full duplex here.
*/
ctrl0 |= MVPP2_GMAC_PORT_TYPE_MASK;
an |= MVPP2_GMAC_CONFIG_GMII_SPEED |
@@ -8216,7 +8241,8 @@ static void mvpp2_gmac_config(struct mvpp2_port *port, unsigned int mode,
an |= MVPP2_GMAC_FC_ADV_ASM_EN;
if (state->interface == PHY_INTERFACE_MODE_SGMII ||
- state->interface == PHY_INTERFACE_MODE_1000BASEX) {
+ state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+ state->interface == PHY_INTERFACE_MODE_2500BASEX) {
an |= MVPP2_GMAC_IN_BAND_AUTONEG;
ctrl2 |= MVPP2_GMAC_INBAND_AN_MASK | MVPP2_GMAC_PCS_ENABLE_MASK;
@@ -8279,7 +8305,8 @@ static void mvpp2_mac_config(struct net_device *dev, unsigned int mode,
mvpp2_xlg_config(port, mode, state);
else if (phy_interface_mode_is_rgmii(state->interface) ||
state->interface == PHY_INTERFACE_MODE_SGMII ||
- state->interface == PHY_INTERFACE_MODE_1000BASEX)
+ state->interface == PHY_INTERFACE_MODE_1000BASEX ||
+ state->interface == PHY_INTERFACE_MODE_2500BASEX)
mvpp2_gmac_config(port, mode, state);
if (port->priv->hw_version == MVPP21 && port->flags & MVPP2_F_LOOPBACK)
--
2.17.0
next prev parent reply other threads:[~2018-05-04 13:56 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-05-04 13:56 [PATCH net-next v2 00/13] net: mvpp2: phylink conversion Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 01/13] net: phy: sfp: make the i2c-bus property really optional Antoine Tenart
2018-05-04 17:03 ` Florian Fainelli
2018-05-04 17:19 ` Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 02/13] net: phy: sfp: handle non-wired SFP connectors Antoine Tenart
2018-05-04 17:04 ` Florian Fainelli
2018-05-04 17:17 ` Andrew Lunn
2018-05-04 17:23 ` Antoine Tenart
2018-05-05 15:39 ` Thomas Petazzoni
2018-05-05 17:48 ` Andrew Lunn
2018-05-08 11:52 ` Russell King - ARM Linux
2018-05-14 9:26 ` Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 03/13] net: phy: sfp: warn the user when no tx_disable pin is available Antoine Tenart
2018-05-04 17:07 ` Florian Fainelli
2018-05-04 17:14 ` Andrew Lunn
2018-05-05 20:38 ` Florian Fainelli
2018-05-05 20:52 ` Andrew Lunn
2018-05-08 12:45 ` Russell King - ARM Linux
2018-05-08 11:53 ` Russell King - ARM Linux
2018-05-04 13:56 ` [PATCH net-next v2 04/13] net: mvpp2: align the ethtool ops definition Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 05/13] net: mvpp2: phylink support Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 06/13] phy: add 2.5G SGMII mode to the phy_mode enum Antoine Tenart
2018-05-08 12:34 ` Russell King - ARM Linux
2018-05-14 8:37 ` Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 07/13] phy: cp110-comphy: 2.5G SGMII mode Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 08/13] net: mvpp2: 1000baseX support Antoine Tenart
2018-05-04 13:56 ` Antoine Tenart [this message]
2018-05-04 13:56 ` [PATCH net-next v2 10/13] arm64: dts: marvell: mcbin: add 10G SFP support Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 11/13] arm64: dts: marvell: mcbin: enable the fourth network interface Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 12/13] arm64: dts: marvell: 7040-db: describe the 10G SFP cage Antoine Tenart
2018-05-04 13:56 ` [PATCH net-next v2 13/13] arm64: dts: marvell: 8040-db: describe the 10G SFP cages Antoine Tenart
2018-05-08 3:18 ` [PATCH net-next v2 00/13] net: mvpp2: phylink conversion David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20180504135643.23466-10-antoine.tenart@bootlin.com \
--to=antoine.tenart@bootlin.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).