[PATCH v2 17/18] arm64: dts: allwinner: a64: NanoPi-A64: Add Wifi/Bluetooth chip

[maxime.ripard@bootlin.com (Maxime Ripard)]

On Thu, Jul 26, 2018 at 01:35:31AM +0100, Andre Przywara wrote:
> The NanoPi-A64 has an on-board WiFi/Bluetooth combo chip, connected
> to the usual MMC1 and UART1. The AXP power line is the always-on
> VDD_SYS_3.3V, but it uses pin L2 to enable the regulator.
> As the actual WiFi driver is not in mainline Linux, it doesn't have a
> compatible string, so we omit this from the node.
> 
> Add the respective nodes to the DT to make it usable.
> 
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> ---
>  .../boot/dts/allwinner/sun50i-a64-nanopi-a64.dts   | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts
> index bd35a093e6cd..705e0b23589e 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-a64-nanopi-a64.dts
> @@ -53,11 +53,17 @@
>  	aliases {
>  		ethernet0 = &emac;
>  		serial0 = &uart0;
> +		serial1 = &uart1;
>  	};
>  
>  	chosen {
>  		stdout-path = "serial0:115200n8";
>  	};
> +
> +	wifi_pwrseq: wifi_pwrseq {
> +		compatible = "mmc-pwrseq-simple";
> +		reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */
> +	};
>  };
>  
>  &ehci0 {
> @@ -105,6 +111,24 @@
>  	status = "okay";
>  };
>  
> +&mmc1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc1_pins>;
> +	vmmc-supply = <&reg_dcdc1>;
> +	vqmmc-supply = <&reg_dldo4>;
> +	mmc-pwrseq = <&wifi_pwrseq>;
> +	bus-width = <4>;
> +	non-removable;
> +	status = "okay";
> +
> +	rtl8189etv: wifi at 1 {
> +		reg = <1>;
> +		interrupt-parent = <&r_pio>;
> +		interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* PL3 */
> +		interrupt-names = "host-wake";
> +	};
> +};
> +
>  &ohci0 {
>  	status = "okay";
>  };
> @@ -222,6 +246,13 @@
>  	status = "okay";
>  };
>  
> +/* Connected to the Bluetooth UART, with hardware handshake pins */
> +&uart1 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
> +	status = "okay";
> +};

Same thing here, if it has serdev support, then it should have a real
node here.

Maxime

-- 
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20180726/78506723/attachment.sig>