[PATCH 2/3] ARM: dts: sun8i: h3: Split out non-SoC-specific parts of Bananapi M2 Plus

Chen-Yu Tsai
2018-08-30T08:09:25Z

Three more variants of the Bananapi M2 Plus have been introduced. One
with the H5 instead of the H3, another with the H2+ instead, and the
last with the H3 but with WiFi and eMMC removed.

All these variants use the same board. This patch splits out the
non-SoC-specific parts of the device tree, so that they can be shared
among all the variants. The original Bananapi M2 Plus has been renamed
to Bananapi M2 Plus H3.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
---
.../boot/dts/sun8i-h3-bananapi-m2-plus.dts | 190 +-----------------
...2-plus.dts => sunxi-bananapi-m2-plus.dtsi} | 5 -
2 files changed, 2 insertions(+), 193 deletions(-)
copy arch/arm/boot/dts/{sun8i-h3-bananapi-m2-plus.dts => sunxi-bananapi-m2-plus.dtsi} (97%)

diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
index bdda0d99128e..195a75da13f1 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
@@ -42,195 +42,9 @@

/dts-v1/;
#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
+#include "sunxi-bananapi-m2-plus.dtsi"

/ {
- model = "Banana Pi BPI-M2-Plus";
+ model = "Banana Pi BPI-M2-Plus H3";
compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
-
- aliases {
- ethernet0 = &emac;
- serial0 = &uart0;
- serial1 = &uart1;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- connector {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con_in: endpoint {
- remote-endpoint = <&hdmi_out_con>;
- };
- };
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
-
- pwr_led {
- label = "bananapi-m2-plus:red:pwr";
- gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
- default-state = "on";
- };
- };
-
- gpio_keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
-
- sw4 {
- label = "power";
- linux,code = <BTN_0>;
- gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
- };
- };
-
- reg_gmac_3v3: gmac-3v3 {
- compatible = "regulator-fixed";
- regulator-name = "gmac-3v3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- startup-delay-us = <100000>;
- enable-active-high;
- gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>;
- };
-
- wifi_pwrseq: wifi_pwrseq {
- compatible = "mmc-pwrseq-simple";
- pinctrl-names = "default";
- reset-gpios = <&r_pio 0 7 GPIO_ACTIVE_LOW>; /* PL7 */
- };
-};
-
-&de {
- status = "okay";
-};
-
-&ehci0 {
- status = "okay";
-};
-
-&ehci1 {
- status = "okay";
-};
-
-&ehci2 {
- status = "okay";
-};
-
-&emac {
- pinctrl-names = "default";
- pinctrl-0 = <&emac_rgmii_pins>;
- phy-supply = <&reg_gmac_3v3>;
- phy-handle = <&ext_rgmii_phy>;
- phy-mode = "rgmii";
-
- status = "okay";
-};
-
-&external_mdio {
- ext_rgmii_phy: ethernet-phy at 1 {
- compatible = "ethernet-phy-ieee802.3-c22";
- reg = <1>;
- };
-};
-
-&hdmi {
- status = "okay";
-};
-
-&hdmi_out {
- hdmi_out_con: endpoint {
- remote-endpoint = <&hdmi_con_in>;
- };
-};
-
-&ir {
- pinctrl-names = "default";
- pinctrl-0 = <&ir_pins_a>;
- status = "okay";
-};
-
-&mmc0 {
- vmmc-supply = <&reg_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
- status = "okay";
-};
-
-&mmc1 {
- vmmc-supply = <&reg_vcc3v3>;
- vqmmc-supply = <&reg_vcc3v3>;
- mmc-pwrseq = <&wifi_pwrseq>;
- bus-width = <4>;
- non-removable;
- status = "okay";
-
- brcmf: wifi at 1 {
- reg = <1>;
- compatible = "brcm,bcm4329-fmac";
- interrupt-parent = <&pio>;
- interrupts = <6 10 IRQ_TYPE_LEVEL_LOW>; /* PG10 / EINT10 */
- interrupt-names = "host-wake";
- };
-};
-
-&mmc2 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc2_8bit_pins>;
- vmmc-supply = <&reg_vcc3v3>;
- vqmmc-supply = <&reg_vcc3v3>;
- bus-width = <8>;
- non-removable;
- status = "okay";
-};
-
-&ohci0 {
- status = "okay";
-};
-
-&ohci1 {
- status = "okay";
-};
-
-&ohci2 {
- status = "okay";
-};
-
-&reg_usb0_vbus {
- gpio = <&pio 3 11 GPIO_ACTIVE_HIGH>; /* PD11 */
- status = "okay";
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
-};
-
-&uart1 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
- status = "okay";
-};
-
-&usb_otg {
- dr_mode = "otg";
- status = "okay";
-};
-
-&usbphy {
- usb0_id_det-gpios = <&r_pio 0 6 GPIO_ACTIVE_HIGH>; /* PL6 */
- usb0_vbus-supply = <&reg_usb0_vbus>;
- /* USB host VBUS is on as long as VCC-IO is on */
- status = "okay";
};
diff --git a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
similarity index 97%
copy from arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
copy to arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
index bdda0d99128e..b3283aeb5b7d 100644
--- a/arch/arm/boot/dts/sun8i-h3-bananapi-m2-plus.dts
+++ b/arch/arm/boot/dts/sunxi-bananapi-m2-plus.dtsi
@@ -40,17 +40,12 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/

-/dts-v1/;
-#include "sun8i-h3.dtsi"
#include "sunxi-common-regulators.dtsi"

#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>

/ {
- model = "Banana Pi BPI-M2-Plus";
- compatible = "sinovoip,bpi-m2-plus", "allwinner,sun8i-h3";
-
aliases {
ethernet0 = &emac;
serial0 = &uart0;
--
2.18.0