From mboxrd@z Thu Jan  1 00:00:00 1970
From: boris.brezillon@bootlin.com (Boris Brezillon)
Date: Thu, 18 Oct 2018 16:24:49 +0200
Subject: [PATCH v5 2/2] mtd: rawnand: meson: add support for Amlogic
 NAND flash controller
In-Reply-To: <1539839345-14021-3-git-send-email-jianxin.pan@amlogic.com>
References: <1539839345-14021-1-git-send-email-jianxin.pan@amlogic.com>
 <1539839345-14021-3-git-send-email-jianxin.pan@amlogic.com>
Message-ID: <20181018162449.3fe433e7@bbrezillon>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On Thu, 18 Oct 2018 13:09:05 +0800
Jianxin Pan <jianxin.pan@amlogic.com> wrote:

> +static int meson_nfc_exec_op(struct nand_chip *chip,
> +			     const struct nand_operation *op, bool check_only)
> +{
> +	struct mtd_info *mtd = nand_to_mtd(chip);
> +	struct meson_nfc *nfc = nand_get_controller_data(chip);
> +	const struct nand_op_instr *instr = NULL;
> +	int ret = 0, cmd;
> +	unsigned int op_id;
> +	int i;
> +
> +	for (op_id = 0; op_id < op->ninstrs; op_id++) {
> +		instr = &op->instrs[op_id];
> +		switch (instr->type) {
> +		case NAND_OP_CMD_INSTR:
> +			if (instr->ctx.cmd.opcode == NAND_CMD_STATUS)
> +				meson_nfc_cmd_idle(nfc, nfc->timing.twb);

Hm, I don't want drivers to base their decisions on the opcode value.
There's a ->delay_ns field in the instruction object, can't you use
that one instead? Also, I don't understand why this is only needed for
the STATUS command. It should normally be applied to all instructions.

> +			cmd = nfc->param.chip_select | NFC_CMD_CLE;
> +			cmd |= instr->ctx.cmd.opcode & 0xff;
> +			writel(cmd, nfc->reg_base + NFC_REG_CMD);
> +			if (instr->ctx.cmd.opcode == NAND_CMD_STATUS)
> +				meson_nfc_cmd_idle(nfc, nfc->timing.twhr);
> +			break;
> +
> +		case NAND_OP_ADDR_INSTR:
> +			for (i = 0; i < instr->ctx.addr.naddrs; i++) {
> +				cmd = nfc->param.chip_select | NFC_CMD_ALE;
> +				cmd |= instr->ctx.addr.addrs[i] & 0xff;
> +				writel(cmd, nfc->reg_base + NFC_REG_CMD);
> +			}
> +			break;
> +
> +		case NAND_OP_DATA_IN_INSTR:
> +			meson_nfc_read_buf(mtd, instr->ctx.data.buf.in,
> +					   instr->ctx.data.len);
> +			break;
> +
> +		case NAND_OP_DATA_OUT_INSTR:
> +			meson_nfc_write_buf(mtd, instr->ctx.data.buf.out,
> +					    instr->ctx.data.len);
> +			break;
> +
> +		case NAND_OP_WAITRDY_INSTR:
> +			meson_nfc_queue_rb(nfc, instr->ctx.waitrdy.timeout_ms);
> +			break;
> +		}
> +	}
> +	return ret;
> +}