* [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH @ 2018-10-04 22:42 Marek Vasut 2018-10-04 22:42 ` [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board Marek Vasut 2018-10-16 22:32 ` [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Rob Herring 0 siblings, 2 replies; 7+ messages in thread From: Marek Vasut @ 2018-10-04 22:42 UTC (permalink / raw) To: linux-arm-kernel Add vendor prefix for Menlo Systems GmbH, http://www.menlosystems.com/ . Signed-off-by: Marek Vasut <marex@denx.de> Cc: Rob Herring <robh+dt@kernel.org> Cc: devicetree at vger.kernel.org --- Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + 1 file changed, 1 insertion(+) diff --git a/Documentation/devicetree/bindings/vendor-prefixes.txt b/Documentation/devicetree/bindings/vendor-prefixes.txt index 4cf887bac4ac..2bf470e06a15 100644 --- a/Documentation/devicetree/bindings/vendor-prefixes.txt +++ b/Documentation/devicetree/bindings/vendor-prefixes.txt @@ -233,6 +233,7 @@ melexis Melexis N.V. melfas MELFAS Inc. mellanox Mellanox Technologies memsic MEMSIC Inc. +menlo Menlo Systems GmbH merrii Merrii Technology Co., Ltd. micrel Micrel Inc. microchip Microchip Technology Inc. -- 2.18.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board 2018-10-04 22:42 [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Marek Vasut @ 2018-10-04 22:42 ` Marek Vasut 2019-02-18 12:04 ` Marek Vasut 2018-10-16 22:32 ` [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Rob Herring 1 sibling, 1 reply; 7+ messages in thread From: Marek Vasut @ 2018-10-04 22:42 UTC (permalink / raw) To: linux-arm-kernel Add device tree for the Menlosystems board based on i.MX53 M53 SoM. Signed-off-by: Marek Vasut <marex@denx.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/imx53-m53menlo.dts | 327 +++++++++++++++++++++++++++ 2 files changed, 328 insertions(+) create mode 100644 arch/arm/boot/dts/imx53-m53menlo.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index b0e966d625b9..731fc7de76b3 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -376,6 +376,7 @@ dtb-$(CONFIG_SOC_IMX53) += \ imx53-kp-ddc.dtb \ imx53-kp-hsc.dtb \ imx53-m53evk.dtb \ + imx53-m53menlo.dtb \ imx53-mba53.dtb \ imx53-ppd.dtb \ imx53-qsb.dtb \ diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts new file mode 100644 index 000000000000..405a57ad01a7 --- /dev/null +++ b/arch/arm/boot/dts/imx53-m53menlo.dts @@ -0,0 +1,327 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright (C) 2017 Marek Vasut <marex@denx.de> + */ + +/dts-v1/; +#include "imx53-m53.dtsi" + +/ { + model = "MENLO M53 EMBEDDED DEVICE"; + compatible = "fsl,imx53"; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&led_pin_gpio>; + + user1 { + label = "TestLed601"; + gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "mmc0"; + }; + + user2 { + label = "TestLed602"; + gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; + linux,default-trigger = "heartbeat"; + }; + + eth { + label = "EthLedYe"; + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; + linux,default-trigger = "none"; + }; + }; + + panel { + compatible = "edt,etm070080dh6"; + enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; + + port { + panel_in: endpoint { + remote-endpoint = <&lvds0_out>; + }; + }; + }; + + regulators { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <0>; + + reg_usbh1_vbus: regulator at 3 { + compatible = "regulator-fixed"; + reg = <3>; + regulator-name = "vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpio1 2 0>; + }; + }; +}; + +&can1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can1>; + status = "okay"; +}; + +&can2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2>; + status = "okay"; +}; + +&clks { + assigned-clocks = <&clks IMX5_CLK_CKO1_SEL>, + <&clks IMX5_CLK_CKO1_PODF>, + <&clks IMX5_CLK_CKO1>; + assigned-clock-parents = <&clks IMX5_CLK_AHB>; + assigned-clock-rates = <133333334>, <33333334>, <33333334>; +}; + +&esdhc1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_esdhc1>; + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + +&fec { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_fec>; + phy-mode = "rmii"; + status = "okay"; +}; + +&i2c1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + edt-ft5x06 at 38 { + compatible = "edt,edt-ft5x06"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_edt_ft5x06>; + interrupt-parent = <&gpio6>; + interrupts = <5 GPIO_ACTIVE_LOW>; + reset-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; + wake-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; + }; + + eeprom at 50 { + compatible = "atmel,24c64"; + reg = <0x50>; + pagesize = <32>; + }; + + dac at 60 { + compatible = "microchip,mcp4725"; + reg = <0x60>; + }; +}; + +&i2c2 { + stmpe610 at 41 { + status = "disabled"; + }; +}; + +&i2c3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; +}; + +&iomuxc { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_hog>; + + imx53-m53evk { + hoggrp { + fsl,pins = < + MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 + MX53_PAD_EIM_EB3__GPIO2_31 0x80000000 + MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 + MX53_PAD_GPIO_19__CCM_CLKO 0x1d5 + MX53_PAD_CSI0_MCLK__CCM_CSI0_MCLK 0x1d5 + MX53_PAD_CSI0_DAT4__GPIO5_22 0x1d5 + MX53_PAD_CSI0_DAT5__GPIO5_23 0x1d5 + MX53_PAD_CSI0_DAT6__GPIO5_24 0x1d5 + MX53_PAD_CSI0_DAT7__GPIO5_25 0x1d5 + MX53_PAD_CSI0_DAT8__GPIO5_26 0x1d5 + MX53_PAD_CSI0_DAT9__GPIO5_27 0x1d5 + MX53_PAD_CSI0_DAT10__GPIO5_28 0x1d5 + MX53_PAD_CSI0_DAT11__GPIO5_29 0x1d5 + MX53_PAD_CSI0_DAT14__GPIO6_0 0x1d5 + >; + }; + + led_pin_gpio: led_gpio at 0 { + fsl,pins = < + MX53_PAD_CSI0_DAT15__GPIO6_1 0x1d5 + MX53_PAD_CSI0_DAT16__GPIO6_2 0x1d5 + >; + }; + + pinctrl_can1: can1grp { + fsl,pins = < + MX53_PAD_GPIO_7__CAN1_TXCAN 0x80000000 + MX53_PAD_GPIO_8__CAN1_RXCAN 0x80000000 + >; + }; + + pinctrl_can2: can2grp { + fsl,pins = < + MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000 + MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000 + >; + }; + + pinctrl_display_gpio: display-gpiogrp { + fsl,pins = < + MX53_PAD_CSI0_DAT12__GPIO5_30 0x1d5 /* Reset */ + MX53_PAD_CSI0_DAT13__GPIO5_31 0x1d5 /* Interrupt */ + >; + }; + + pinctrl_edt_ft5x06: edt-ft5x06grp { + fsl,pins = < + MX53_PAD_PATA_DATA9__GPIO2_9 0x1d5 /* Reset */ + MX53_PAD_CSI0_DAT19__GPIO6_5 0x1d5 /* Interrupt */ + MX53_PAD_PATA_DATA10__GPIO2_10 0x1d5 /* Wake */ + >; + }; + + pinctrl_esdhc1: esdhc1grp { + fsl,pins = < + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 + >; + }; + + pinctrl_fec: fecgrp { + fsl,pins = < + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000 + MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 + MX53_PAD_GPIO_5__I2C3_SCL 0xc0000000 + >; + }; + + pinctrl_lvds0: lvds0grp { + fsl,pins = < + MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000 + MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000 + MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000 + MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000 + MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000 + >; + }; + + pinctrl_power_button_gpio: powerbutgrp { + fsl,pins = < + MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD 0x1d5 + >; + }; + + pinctrl_power_out_gpio: poweroutgrp { + fsl,pins = < + MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD 0x1d5 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 + >; + }; + + pinctrl_usb: usbgrp { + fsl,pins = < + MX53_PAD_GPIO_2__GPIO1_2 0x80000000 + MX53_PAD_GPIO_3__USBOH3_USBH1_OC 0x80000000 + >; + }; + }; +}; + +&ldb { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_lvds0>; + status = "okay"; + + lvds0: lvds-channel at 0 { + fsl,data-mapping = "spwg"; + fsl,data-width = <18>; + status = "okay"; + + port at 2 { + reg = <2>; + lvds0_out: endpoint { + remote-endpoint = <&panel_in>; + }; + }; + }; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usbh1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_usb>; + vbus-supply = <®_usbh1_vbus>; + phy_type = "utmi"; + dr_mode = "peripheral"; + status = "okay"; +}; + +&usbotg { + dr_mode = "peripheral"; + status = "okay"; +}; -- 2.18.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board 2018-10-04 22:42 ` [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board Marek Vasut @ 2019-02-18 12:04 ` Marek Vasut 2019-02-28 14:37 ` Shawn Guo 0 siblings, 1 reply; 7+ messages in thread From: Marek Vasut @ 2019-02-18 12:04 UTC (permalink / raw) To: linux-arm-kernel; +Cc: Shawn Guo On 10/5/18 12:42 AM, Marek Vasut wrote: > Add device tree for the Menlosystems board based on i.MX53 M53 SoM. > > Signed-off-by: Marek Vasut <marex@denx.de> Shawn, bump ? > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/imx53-m53menlo.dts | 327 +++++++++++++++++++++++++++ > 2 files changed, 328 insertions(+) > create mode 100644 arch/arm/boot/dts/imx53-m53menlo.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index b0e966d625b9..731fc7de76b3 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -376,6 +376,7 @@ dtb-$(CONFIG_SOC_IMX53) += \ > imx53-kp-ddc.dtb \ > imx53-kp-hsc.dtb \ > imx53-m53evk.dtb \ > + imx53-m53menlo.dtb \ > imx53-mba53.dtb \ > imx53-ppd.dtb \ > imx53-qsb.dtb \ > diff --git a/arch/arm/boot/dts/imx53-m53menlo.dts b/arch/arm/boot/dts/imx53-m53menlo.dts > new file mode 100644 > index 000000000000..405a57ad01a7 > --- /dev/null > +++ b/arch/arm/boot/dts/imx53-m53menlo.dts > @@ -0,0 +1,327 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright (C) 2017 Marek Vasut <marex@denx.de> > + */ > + > +/dts-v1/; > +#include "imx53-m53.dtsi" > + > +/ { > + model = "MENLO M53 EMBEDDED DEVICE"; > + compatible = "fsl,imx53"; > + > + leds { > + compatible = "gpio-leds"; > + pinctrl-names = "default"; > + pinctrl-0 = <&led_pin_gpio>; > + > + user1 { > + label = "TestLed601"; > + gpios = <&gpio6 1 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "mmc0"; > + }; > + > + user2 { > + label = "TestLed602"; > + gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "heartbeat"; > + }; > + > + eth { > + label = "EthLedYe"; > + gpios = <&gpio2 11 GPIO_ACTIVE_LOW>; > + linux,default-trigger = "none"; > + }; > + }; > + > + panel { > + compatible = "edt,etm070080dh6"; > + enable-gpios = <&gpio6 0 GPIO_ACTIVE_HIGH>; > + > + port { > + panel_in: endpoint { > + remote-endpoint = <&lvds0_out>; > + }; > + }; > + }; > + > + regulators { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <0>; > + > + reg_usbh1_vbus: regulator@3 { > + compatible = "regulator-fixed"; > + reg = <3>; > + regulator-name = "vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpio1 2 0>; > + }; > + }; > +}; > + > +&can1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_can1>; > + status = "okay"; > +}; > + > +&can2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_can2>; > + status = "okay"; > +}; > + > +&clks { > + assigned-clocks = <&clks IMX5_CLK_CKO1_SEL>, > + <&clks IMX5_CLK_CKO1_PODF>, > + <&clks IMX5_CLK_CKO1>; > + assigned-clock-parents = <&clks IMX5_CLK_AHB>; > + assigned-clock-rates = <133333334>, <33333334>, <33333334>; > +}; > + > +&esdhc1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_esdhc1>; > + cd-gpios = <&gpio1 1 GPIO_ACTIVE_LOW>; > + wp-gpios = <&gpio1 9 GPIO_ACTIVE_HIGH>; > + status = "okay"; > +}; > + > +&fec { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_fec>; > + phy-mode = "rmii"; > + status = "okay"; > +}; > + > +&i2c1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c1>; > + status = "okay"; > + > + edt-ft5x06@38 { > + compatible = "edt,edt-ft5x06"; > + reg = <0x38>; > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_edt_ft5x06>; > + interrupt-parent = <&gpio6>; > + interrupts = <5 GPIO_ACTIVE_LOW>; > + reset-gpios = <&gpio2 9 GPIO_ACTIVE_LOW>; > + wake-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>; > + }; > + > + eeprom@50 { > + compatible = "atmel,24c64"; > + reg = <0x50>; > + pagesize = <32>; > + }; > + > + dac@60 { > + compatible = "microchip,mcp4725"; > + reg = <0x60>; > + }; > +}; > + > +&i2c2 { > + stmpe610@41 { > + status = "disabled"; > + }; > +}; > + > +&i2c3 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_i2c3>; > + status = "okay"; > +}; > + > +&iomuxc { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_hog>; > + > + imx53-m53evk { > + hoggrp { > + fsl,pins = < > + MX53_PAD_GPIO_0__CCM_SSI_EXT1_CLK 0x80000000 > + MX53_PAD_EIM_EB3__GPIO2_31 0x80000000 > + MX53_PAD_PATA_DA_0__GPIO7_6 0x80000000 > + MX53_PAD_GPIO_19__CCM_CLKO 0x1d5 > + MX53_PAD_CSI0_MCLK__CCM_CSI0_MCLK 0x1d5 > + MX53_PAD_CSI0_DAT4__GPIO5_22 0x1d5 > + MX53_PAD_CSI0_DAT5__GPIO5_23 0x1d5 > + MX53_PAD_CSI0_DAT6__GPIO5_24 0x1d5 > + MX53_PAD_CSI0_DAT7__GPIO5_25 0x1d5 > + MX53_PAD_CSI0_DAT8__GPIO5_26 0x1d5 > + MX53_PAD_CSI0_DAT9__GPIO5_27 0x1d5 > + MX53_PAD_CSI0_DAT10__GPIO5_28 0x1d5 > + MX53_PAD_CSI0_DAT11__GPIO5_29 0x1d5 > + MX53_PAD_CSI0_DAT14__GPIO6_0 0x1d5 > + >; > + }; > + > + led_pin_gpio: led_gpio@0 { > + fsl,pins = < > + MX53_PAD_CSI0_DAT15__GPIO6_1 0x1d5 > + MX53_PAD_CSI0_DAT16__GPIO6_2 0x1d5 > + >; > + }; > + > + pinctrl_can1: can1grp { > + fsl,pins = < > + MX53_PAD_GPIO_7__CAN1_TXCAN 0x80000000 > + MX53_PAD_GPIO_8__CAN1_RXCAN 0x80000000 > + >; > + }; > + > + pinctrl_can2: can2grp { > + fsl,pins = < > + MX53_PAD_KEY_COL4__CAN2_TXCAN 0x80000000 > + MX53_PAD_KEY_ROW4__CAN2_RXCAN 0x80000000 > + >; > + }; > + > + pinctrl_display_gpio: display-gpiogrp { > + fsl,pins = < > + MX53_PAD_CSI0_DAT12__GPIO5_30 0x1d5 /* Reset */ > + MX53_PAD_CSI0_DAT13__GPIO5_31 0x1d5 /* Interrupt */ > + >; > + }; > + > + pinctrl_edt_ft5x06: edt-ft5x06grp { > + fsl,pins = < > + MX53_PAD_PATA_DATA9__GPIO2_9 0x1d5 /* Reset */ > + MX53_PAD_CSI0_DAT19__GPIO6_5 0x1d5 /* Interrupt */ > + MX53_PAD_PATA_DATA10__GPIO2_10 0x1d5 /* Wake */ > + >; > + }; > + > + pinctrl_esdhc1: esdhc1grp { > + fsl,pins = < > + MX53_PAD_SD1_DATA0__ESDHC1_DAT0 0x1d5 > + MX53_PAD_SD1_DATA1__ESDHC1_DAT1 0x1d5 > + MX53_PAD_SD1_DATA2__ESDHC1_DAT2 0x1d5 > + MX53_PAD_SD1_DATA3__ESDHC1_DAT3 0x1d5 > + MX53_PAD_SD1_CMD__ESDHC1_CMD 0x1d5 > + MX53_PAD_SD1_CLK__ESDHC1_CLK 0x1d5 > + >; > + }; > + > + pinctrl_fec: fecgrp { > + fsl,pins = < > + MX53_PAD_FEC_MDC__FEC_MDC 0x80000000 > + MX53_PAD_FEC_MDIO__FEC_MDIO 0x80000000 > + MX53_PAD_FEC_REF_CLK__FEC_TX_CLK 0x80000000 > + MX53_PAD_FEC_RX_ER__FEC_RX_ER 0x80000000 > + MX53_PAD_FEC_CRS_DV__FEC_RX_DV 0x80000000 > + MX53_PAD_FEC_RXD1__FEC_RDATA_1 0x80000000 > + MX53_PAD_FEC_RXD0__FEC_RDATA_0 0x80000000 > + MX53_PAD_FEC_TX_EN__FEC_TX_EN 0x80000000 > + MX53_PAD_FEC_TXD1__FEC_TDATA_1 0x80000000 > + MX53_PAD_FEC_TXD0__FEC_TDATA_0 0x80000000 > + >; > + }; > + > + pinctrl_i2c1: i2c1grp { > + fsl,pins = < > + MX53_PAD_EIM_D21__I2C1_SCL 0xc0000000 > + MX53_PAD_EIM_D28__I2C1_SDA 0xc0000000 > + >; > + }; > + > + pinctrl_i2c3: i2c3grp { > + fsl,pins = < > + MX53_PAD_GPIO_6__I2C3_SDA 0xc0000000 > + MX53_PAD_GPIO_5__I2C3_SCL 0xc0000000 > + >; > + }; > + > + pinctrl_lvds0: lvds0grp { > + fsl,pins = < > + MX53_PAD_LVDS0_CLK_P__LDB_LVDS0_CLK 0x80000000 > + MX53_PAD_LVDS0_TX0_P__LDB_LVDS0_TX0 0x80000000 > + MX53_PAD_LVDS0_TX1_P__LDB_LVDS0_TX1 0x80000000 > + MX53_PAD_LVDS0_TX2_P__LDB_LVDS0_TX2 0x80000000 > + MX53_PAD_LVDS0_TX3_P__LDB_LVDS0_TX3 0x80000000 > + >; > + }; > + > + pinctrl_power_button_gpio: powerbutgrp { > + fsl,pins = < > + MX53_PAD_SD2_DATA0__AUDMUX_AUD4_RXD 0x1d5 > + >; > + }; > + > + pinctrl_power_out_gpio: poweroutgrp { > + fsl,pins = < > + MX53_PAD_SD2_DATA2__AUDMUX_AUD4_TXD 0x1d5 > + >; > + }; > + > + pinctrl_uart1: uart1grp { > + fsl,pins = < > + MX53_PAD_PATA_DIOW__UART1_TXD_MUX 0x1e4 > + MX53_PAD_PATA_DMACK__UART1_RXD_MUX 0x1e4 > + >; > + }; > + > + pinctrl_uart2: uart2grp { > + fsl,pins = < > + MX53_PAD_PATA_BUFFER_EN__UART2_RXD_MUX 0x1e4 > + MX53_PAD_PATA_DMARQ__UART2_TXD_MUX 0x1e4 > + >; > + }; > + > + pinctrl_usb: usbgrp { > + fsl,pins = < > + MX53_PAD_GPIO_2__GPIO1_2 0x80000000 > + MX53_PAD_GPIO_3__USBOH3_USBH1_OC 0x80000000 > + >; > + }; > + }; > +}; > + > +&ldb { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_lvds0>; > + status = "okay"; > + > + lvds0: lvds-channel@0 { > + fsl,data-mapping = "spwg"; > + fsl,data-width = <18>; > + status = "okay"; > + > + port@2 { > + reg = <2>; > + lvds0_out: endpoint { > + remote-endpoint = <&panel_in>; > + }; > + }; > + }; > +}; > + > +&uart1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart1>; > + status = "okay"; > +}; > + > +&uart2 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_uart2>; > + status = "okay"; > +}; > + > +&usbh1 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_usb>; > + vbus-supply = <®_usbh1_vbus>; > + phy_type = "utmi"; > + dr_mode = "peripheral"; > + status = "okay"; > +}; > + > +&usbotg { > + dr_mode = "peripheral"; > + status = "okay"; > +}; > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board 2019-02-18 12:04 ` Marek Vasut @ 2019-02-28 14:37 ` Shawn Guo 2019-03-02 14:52 ` Marek Vasut 0 siblings, 1 reply; 7+ messages in thread From: Shawn Guo @ 2019-02-28 14:37 UTC (permalink / raw) To: Marek Vasut; +Cc: linux-arm-kernel On Mon, Feb 18, 2019 at 01:04:36PM +0100, Marek Vasut wrote: > On 10/5/18 12:42 AM, Marek Vasut wrote: > > Add device tree for the Menlosystems board based on i.MX53 M53 SoM. > > > > Signed-off-by: Marek Vasut <marex@denx.de> > > Shawn, bump ? Please resend it to recipients that scripts/get_maintainer.pl gives. Shawn _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board 2019-02-28 14:37 ` Shawn Guo @ 2019-03-02 14:52 ` Marek Vasut 0 siblings, 0 replies; 7+ messages in thread From: Marek Vasut @ 2019-03-02 14:52 UTC (permalink / raw) To: Shawn Guo; +Cc: linux-arm-kernel On 2/28/19 3:37 PM, Shawn Guo wrote: > On Mon, Feb 18, 2019 at 01:04:36PM +0100, Marek Vasut wrote: >> On 10/5/18 12:42 AM, Marek Vasut wrote: >>> Add device tree for the Menlosystems board based on i.MX53 M53 SoM. >>> >>> Signed-off-by: Marek Vasut <marex@denx.de> >> >> Shawn, bump ? > > Please resend it to recipients that scripts/get_maintainer.pl gives. Thank you for the useful feedback. -- Best regards, Marek Vasut _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH 2018-10-04 22:42 [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Marek Vasut 2018-10-04 22:42 ` [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board Marek Vasut @ 2018-10-16 22:32 ` Rob Herring 2019-02-19 14:06 ` Marek Vasut 1 sibling, 1 reply; 7+ messages in thread From: Rob Herring @ 2018-10-16 22:32 UTC (permalink / raw) To: linux-arm-kernel On Fri, 5 Oct 2018 00:42:26 +0200, Marek Vasut wrote: > Add vendor prefix for Menlo Systems GmbH, http://www.menlosystems.com/ . > > Signed-off-by: Marek Vasut <marex@denx.de> > Cc: Rob Herring <robh+dt@kernel.org> > Cc: devicetree at vger.kernel.org > --- > Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + > 1 file changed, 1 insertion(+) > Reviewed-by: Rob Herring <robh@kernel.org> ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH 2018-10-16 22:32 ` [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Rob Herring @ 2019-02-19 14:06 ` Marek Vasut 0 siblings, 0 replies; 7+ messages in thread From: Marek Vasut @ 2019-02-19 14:06 UTC (permalink / raw) To: Rob Herring; +Cc: devicetree, linux-arm-kernel On 10/17/18 12:32 AM, Rob Herring wrote: > On Fri, 5 Oct 2018 00:42:26 +0200, Marek Vasut wrote: >> Add vendor prefix for Menlo Systems GmbH, http://www.menlosystems.com/ . >> >> Signed-off-by: Marek Vasut <marex@denx.de> >> Cc: Rob Herring <robh+dt@kernel.org> >> Cc: devicetree@vger.kernel.org >> --- >> Documentation/devicetree/bindings/vendor-prefixes.txt | 1 + >> 1 file changed, 1 insertion(+) >> > > Reviewed-by: Rob Herring <robh@kernel.org> Could this be applied separately , so I don't have to repost it ? It seems I'm not getting any feedback from the iMX maintainer for months... _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2019-03-02 15:48 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2018-10-04 22:42 [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Marek Vasut 2018-10-04 22:42 ` [PATCH 2/2] ARM: dts: imx53: Add Menlosystems M53 board Marek Vasut 2019-02-18 12:04 ` Marek Vasut 2019-02-28 14:37 ` Shawn Guo 2019-03-02 14:52 ` Marek Vasut 2018-10-16 22:32 ` [PATCH 1/2] of: Add vendor prefix for Menlo Systems GmbH Rob Herring 2019-02-19 14:06 ` Marek Vasut
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).