linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Raag Jadav <raagjadav@gmail.com>
To: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: alexandre.belloni@bootlin.com, linux-kernel@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org, linux-i2c@vger.kernel.org
Subject: Re: [PATCH] i2c: at91: handle TXRDY interrupt spam
Date: Sat, 4 May 2019 05:28:51 +0530	[thread overview]
Message-ID: <20190503235851.GA4242@pc> (raw)
In-Reply-To: <20190502140116.rim72idpgvq4h4vc@M43218.corp.atmel.com>

On Thu, May 02, 2019 at 04:01:16PM +0200, Ludovic Desroches wrote:
> On Tue, Apr 30, 2019 at 04:03:32AM +0530, Raag Jadav wrote:
> > External E-Mail
> > 
> > 
> > On Mon, Apr 29, 2019 at 11:00:05AM +0200, Ludovic Desroches wrote:
> > > Hello Raag,
> > > 
> > > On Tue, Apr 23, 2019 at 01:06:48PM +0530, Raag Jadav wrote:
> > > > External E-Mail
> > > > 
> > > > 
> > > > Performing i2c write operation while SDA or SCL line is held
> > > > or grounded by slave device, we go into infinite at91_twi_write_next_byte
> > > > loop with TXRDY interrupt spam.
> > > 
> > > Sorry but I am not sure to have the full picture, the controller is in
> > > slave or master mode?
> > > 
> > > SVREAD is only used in slave mode. When SVREAD is set, it means that a read
> > > access is performed and your issue concerns the write operation.
> > > 
> > > Regards
> > > 
> > > Ludovic
> > 
> > Yes, even though the datasheet suggests that SVREAD is irrelevant in master mode,
> > TXRDY and SVREAD are the only ones being set in status register upon reproducing the issue.
> > Couldn't think of a better way to handle such strange behaviour.
> > Any suggestions would be appreciated.
> 
> I have the confirmation that you can't rely on the SVREAD flag when in
> master mode. This flag should always have the same value.
> 
> I am trying to understand what could lead to your situation. Can you
> give me more details. What kind of device it is? What does lead to this
> situation? Does it happen randomly or not?

One of the sama5d2 based board I worked on, was having trouble complete its boot
because of a faulty i2c device, which was randomly holding down the SDA line
on i2c write operation, not allowing the controller to complete its transmission,
causing a massive TXRDY interrupt spam, ultimately hanging the processor.

Another strange observation was that SVREAD was being set in the status register
along with TXRDY, every time I reproduced the issue.
You can reproduce it by simply grounding the SDA line and performing i2c write
on the bus.

Note that NACK, LOCK or TXCOMP are never set as the transmission never completes.
I'm not sure why slave bits are being set in master mode,
but it's been working reliably for me.

This patch doesn't recover the SDA line. It just prevents the processor from
getting hanged in case of i2c bus lockup.

Cheers,
Raag

> 
> Regards
> 
> Ludovic
> 
> > 
> > Cheers,
> > Raag
> > 
> > > 
> > > > 
> > > > Signed-off-by: Raag Jadav <raagjadav@gmail.com>
> > > > ---
> > > >  drivers/i2c/busses/i2c-at91.c | 6 +++++-
> > > >  1 file changed, 5 insertions(+), 1 deletion(-)
> > > > 
> > > > diff --git a/drivers/i2c/busses/i2c-at91.c b/drivers/i2c/busses/i2c-at91.c
> > > > index 3f3e8b3..b2f5fdb 100644
> > > > --- a/drivers/i2c/busses/i2c-at91.c
> > > > +++ b/drivers/i2c/busses/i2c-at91.c
> > > > @@ -72,6 +72,7 @@
> > > >  #define	AT91_TWI_TXCOMP		BIT(0)	/* Transmission Complete */
> > > >  #define	AT91_TWI_RXRDY		BIT(1)	/* Receive Holding Register Ready */
> > > >  #define	AT91_TWI_TXRDY		BIT(2)	/* Transmit Holding Register Ready */
> > > > +#define	AT91_TWI_SVREAD		BIT(3)	/* Slave Read */
> > > >  #define	AT91_TWI_OVRE		BIT(6)	/* Overrun Error */
> > > >  #define	AT91_TWI_UNRE		BIT(7)	/* Underrun Error */
> > > >  #define	AT91_TWI_NACK		BIT(8)	/* Not Acknowledged */
> > > > @@ -571,7 +572,10 @@ static irqreturn_t atmel_twi_interrupt(int irq, void *dev_id)
> > > >  		at91_disable_twi_interrupts(dev);
> > > >  		complete(&dev->cmd_complete);
> > > >  	} else if (irqstatus & AT91_TWI_TXRDY) {
> > > > -		at91_twi_write_next_byte(dev);
> > > > +		if ((status & AT91_TWI_SVREAD) && (dev->buf_len == 0))
> > > > +			at91_twi_write(dev, AT91_TWI_IDR, AT91_TWI_TXRDY);
> > > > +		else
> > > > +			at91_twi_write_next_byte(dev);
> > > >  	}
> > > >  
> > > >  	/* catch error flags */
> > > > -- 
> > > > 2.7.4
> > > > 
> > > > 
> > 
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> > 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2019-05-03 23:59 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-04-23  7:36 [PATCH] i2c: at91: handle TXRDY interrupt spam Raag Jadav
2019-04-29  9:00 ` Ludovic Desroches
2019-04-29 22:33   ` Raag Jadav
2019-05-02 14:01     ` Ludovic Desroches
2019-05-03 23:58       ` Raag Jadav [this message]
2019-05-06  8:19         ` Eugen.Hristev
2019-05-06 16:02           ` Raag Jadav
2019-05-14  8:52           ` Ludovic Desroches
2019-05-14  8:42         ` Ludovic Desroches

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190503235851.GA4242@pc \
    --to=raagjadav@gmail.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-i2c@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=ludovic.desroches@microchip.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).