linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Fabio Estevam <festevam@gmail.com>
To: shawnguo@kernel.org
Cc: Fabio Estevam <festevam@gmail.com>,
	ezequiel@collabora.com, linux-arm-kernel@lists.infradead.org
Subject: [PATCH 1/2] ARM: dts: imx6qdl-wandboard: Add OV5645 camera support
Date: Mon, 22 Jul 2019 10:36:50 -0300	[thread overview]
Message-ID: <20190722133651.14729-1-festevam@gmail.com> (raw)

From: Ezequiel Garcia <ezequiel@collabora.com>

imx6qdl-wandboard can be connected to a OV5645 camera via
MIPI CSI port. Add support for it.

PAD_GPIO_6 has been originally used for the Ethernet FEC
ERR006687 workaround, but it needs to be used to provide the
camera sensor clock, so adjust it accordingly.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
 arch/arm/boot/dts/imx6qdl-wandboard.dtsi | 73 ++++++++++++++++++++++--
 arch/arm64/boot/dts/freescale/Makefile   |  1 +
 2 files changed, 70 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
index 50d9a989e06a..2cfb4112a467 100644
--- a/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-wandboard.dtsi
@@ -33,6 +33,30 @@
 		spdif-out;
 	};
 
+	reg_1p5v: regulator-1p5v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P5V";
+		regulator-min-microvolt = <1500000>;
+		regulator-max-microvolt = <1500000>;
+		regulator-always-on;
+	};
+
+	reg_1p8v: regulator-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "1P8V";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+		regulator-always-on;
+	};
+
+	reg_2p8v: regulator-2p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "2P8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		regulator-always-on;
+	};
+
 	reg_2p5v: regulator-2p5v {
 		compatible = "regulator-fixed";
 		regulator-name = "2P5V";
@@ -94,6 +118,29 @@
 		VDDIO-supply = <&reg_3p3v>;
 		lrclk-strength = <3>;
 	};
+
+	camera@3c {
+		compatible = "ovti,ov5645";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ov5645>;
+		reg = <0x3c>;
+		clocks = <&clks IMX6QDL_CLK_CKO2>;
+		clock-names = "xclk";
+		clock-frequency = <24000000>;
+		vdddo-supply = <&reg_1p8v>;
+		vdda-supply = <&reg_2p8v>;
+		vddd-supply = <&reg_1p5v>;
+		enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpio4 14 GPIO_ACTIVE_LOW>;
+
+		port {
+			ov5645_to_mipi_csi2: endpoint {
+				remote-endpoint = <&mipi_csi2_in>;
+				clock-lanes = <0>;
+				data-lanes = <1 2>;
+			};
+		};
+	};
 };
 
 &iomuxc {
@@ -128,7 +175,6 @@
 				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
 				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x1b030
 				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0x4001b0a8
-				MX6QDL_PAD_GPIO_6__ENET_IRQ		0x000b1
 			>;
 		};
 
@@ -152,6 +198,14 @@
 			>;
 		};
 
+		pinctrl_ov5645: ov5645grp {
+			fsl,pins = <
+				MX6QDL_PAD_GPIO_3__CCM_CLKO2		0x000b0
+				MX6QDL_PAD_GPIO_6__GPIO1_IO06		0x1b0b0
+				MX6QDL_PAD_KEY_COL4__GPIO4_IO14		0x1b0b0
+			>;
+		};
+
 		pinctrl_spdif: spdifgrp {
 			fsl,pins = <
 				MX6QDL_PAD_ENET_RXD0__SPDIF_OUT		0x1b0b0
@@ -226,12 +280,23 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio3 29 GPIO_ACTIVE_LOW>;
-	interrupts-extended = <&gpio1 6 IRQ_TYPE_LEVEL_HIGH>,
-			      <&intc 0 119 IRQ_TYPE_LEVEL_HIGH>;
-	fsl,err006687-workaround-present;
 	status = "okay";
 };
 
+&mipi_csi {
+	status = "okay";
+
+	port@0 {
+		reg = <0>;
+
+		mipi_csi2_in: endpoint {
+			remote-endpoint = <&ov5645_to_mipi_csi2>;
+			clock-lanes = <0>;
+			data-lanes = <1 2>;
+		};
+	};
+};
+
 &spdif {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_spdif>;
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index c043aca66572..99627a499a73 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -23,6 +23,7 @@ dtb-$(CONFIG_ARCH_LAYERSCAPE) += fsl-lx2160a-rdb.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mm-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-evk.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-rmb3.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mq-zii-ultra-zest.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek.dtb
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

             reply	other threads:[~2019-07-22 13:37 UTC|newest]

Thread overview: 4+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-07-22 13:36 Fabio Estevam [this message]
2019-07-22 13:36 ` [PATCH 2/2] ARM: imx_v6_v7_defconfig: Select the OV5645 camera driver Fabio Estevam
2019-07-22 14:14 ` [PATCH 1/2] ARM: dts: imx6qdl-wandboard: Add OV5645 camera support Ezequiel Garcia
2019-07-22 14:15   ` Fabio Estevam

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190722133651.14729-1-festevam@gmail.com \
    --to=festevam@gmail.com \
    --cc=ezequiel@collabora.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=shawnguo@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).