REGRESSION: i2c-imx endlessly triggers clk warning

[Russell King - ARM Linux admin <linux@armlinux.org.uk>]

Booting 5.2 on the VF610 based ZII rev B board results in the board
not making progress due to an endless stream of:

[  153.077831] ------------[ cut here ]------------
[  153.082528] WARNING: CPU: 0 PID: 15 at drivers/clk/clk.c:924 clk_core_disable_lock+0x18/0x24
[  153.093077] i2c0 already disabled
[  153.096416] Modules linked in:
[  153.099521] CPU: 0 PID: 15 Comm: kworker/0:1 Tainted: G        W         5.2.0+ #321
[  153.107290] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[  153.113772] Workqueue: events deferred_probe_work_func
[  153.118979] [<c0019560>] (unwind_backtrace) from [<c0014734>] (show_stack+0x10/0x14)
[  153.126778] [<c0014734>] (show_stack) from [<c083f8dc>] (dump_stack+0x9c/0xd4)
[  153.134051] [<c083f8dc>] (dump_stack) from [<c0031154>] (__warn+0xf8/0x124)
[  153.141056] [<c0031154>] (__warn) from [<c0031248>] (warn_slowpath_fmt+0x38/0x48)
[  153.148580] [<c0031248>] (warn_slowpath_fmt) from [<c040fde0>] (clk_core_disable_lock+0x18/0x24)
[  153.157413] [<c040fde0>] (clk_core_disable_lock) from [<c058f520>] (i2c_imx_probe+0x554/0x6ec)
[  153.166076] [<c058f520>] (i2c_imx_probe) from [<c04b9178>] (platform_drv_probe+0x48/0x98)
[  153.174297] [<c04b9178>] (platform_drv_probe) from [<c04b7298>] (really_probe+0x1d8/0x2c0)
[  153.182605] [<c04b7298>] (really_probe) from [<c04b7554>] (driver_probe_device+0x5c/0x174)
[  153.190909] [<c04b7554>] (driver_probe_device) from [<c04b58c8>] (bus_for_each_drv+0x44/0x8c)
[  153.199480] [<c04b58c8>] (bus_for_each_drv) from [<c04b746c>] (__device_attach+0xa0/0x108)
[  153.207782] [<c04b746c>] (__device_attach) from [<c04b65a4>] (bus_probe_device+0x88/0x90)
[  153.215999] [<c04b65a4>] (bus_probe_device) from [<c04b6a04>] (deferred_probe_work_func+0x60/0x90)
[  153.225003] [<c04b6a04>] (deferred_probe_work_func) from [<c004f190>] (process_one_work+0x204/0x634)
[  153.234178] [<c004f190>] (process_one_work) from [<c004f618>] (worker_thread+0x20/0x484)
[  153.242315] [<c004f618>] (worker_thread) from [<c0055c2c>] (kthread+0x118/0x150)
[  153.249758] [<c0055c2c>] (kthread) from [<c00090b4>] (ret_from_fork+0x14/0x20)
[  153.257006] Exception stack(0xdde43fb0 to 0xdde43ff8)
[  153.262095] 3fa0:                                     00000000 00000000 00000000 00000000
[  153.270306] 3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[  153.278520] 3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
[  153.285159] irq event stamp: 3323022
[  153.288787] hardirqs last  enabled at (3323021): [<c0861c4c>] _raw_spin_unlock_irq+0x24/0x2c
[  153.297261] hardirqs last disabled at (3323022): [<c040d7a0>] clk_enable_lock+0x10/0x124
[  153.305392] softirqs last  enabled at (3322092): [<c000a504>] __do_softirq+0x344/0x540
[  153.313352] softirqs last disabled at (3322081): [<c00385c0>] irq_exit+0x10c/0x128
[  153.320946] ---[ end trace a506731ccd9bd703 ]---

My guess is that this is due to a combination of e1ab9a468e3b ("i2c:
imx: improve the error handling in i2c_imx_dma_request()") and the fact
that my configuration has CONFIG_FSL_EDMA=m.  Given that the boot makes
no progress, it seems that this driver now requires EDMA to be built-in
_if_ this driver is also built in.  It seems that Kconfig allows an
invalid configuration as far as the driver is concerned.

However, even though it seems that EDMA needs to be built-in with
5.2, this should not trigger the above kernel warning, which suggests
something is wrong in the driver cleanup paths.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel