From: Wolfram Sang <wsa@the-dreams.de>
To: Biwen Li <biwen.li@nxp.com>, Joshua Frkuska <joshua_frkuska@mentor.com>
Cc: shawnguo@kernel.org, s.hauer@pengutronix.de,
linux-kernel@vger.kernel.org, linux-imx@nxp.com,
kernel@pengutronix.de, laurentiu.tudor@nxp.com,
festevam@gmail.com, linux-arm-kernel@lists.infradead.org,
linux-i2c@vger.kernel.org
Subject: Re: i2c: imx: support slave mode for imx I2C driver
Date: Thu, 8 Aug 2019 22:02:02 +0200 [thread overview]
Message-ID: <20190808200202.GA6609@ninjato> (raw)
In-Reply-To: <20190808035343.34120-1-biwen.li@nxp.com>
[-- Attachment #1.1: Type: text/plain, Size: 7905 bytes --]
On Thu, Aug 08, 2019 at 11:53:43AM +0800, Biwen Li wrote:
> The patch supports slave mode for imx I2C driver
>
> Signed-off-by: Biwen Li <biwen.li@nxp.com>
Wow, this is much simpler than the other approach flying around:
http://patchwork.ozlabs.org/patch/1124048/
Can this one be master and slave on the same bus, too?
CCing the author of the other patch.
> ---
> drivers/i2c/busses/i2c-imx.c | 199 ++++++++++++++++++++++++++++++++---
> 1 file changed, 185 insertions(+), 14 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-imx.c b/drivers/i2c/busses/i2c-imx.c
> index b1b8b938d7f4..f7583a9fa56f 100644
> --- a/drivers/i2c/busses/i2c-imx.c
> +++ b/drivers/i2c/busses/i2c-imx.c
> @@ -202,6 +202,9 @@ struct imx_i2c_struct {
> struct pinctrl_state *pinctrl_pins_gpio;
>
> struct imx_i2c_dma *dma;
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> + struct i2c_client *slave;
> +#endif /* CONFIG_I2C_SLAVE */
> };
>
> static const struct imx_i2c_hwdata imx1_i2c_hwdata = {
> @@ -583,23 +586,40 @@ static void i2c_imx_stop(struct imx_i2c_struct *i2c_imx)
> imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
> }
>
> -static irqreturn_t i2c_imx_isr(int irq, void *dev_id)
> +/* Clear interrupt flag bit */
> +static void i2c_imx_clr_if_bit(struct imx_i2c_struct *i2c_imx)
> {
> - struct imx_i2c_struct *i2c_imx = dev_id;
> - unsigned int temp;
> + unsigned int status;
>
> - temp = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
> - if (temp & I2SR_IIF) {
> - /* save status register */
> - i2c_imx->i2csr = temp;
> - temp &= ~I2SR_IIF;
> - temp |= (i2c_imx->hwdata->i2sr_clr_opcode & I2SR_IIF);
> - imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2SR);
> - wake_up(&i2c_imx->queue);
> - return IRQ_HANDLED;
> - }
> + status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
> + status &= ~I2SR_IIF;
> + status |= (i2c_imx->hwdata->i2sr_clr_opcode & I2SR_IIF);
> + imx_i2c_write_reg(status, i2c_imx, IMX_I2C_I2SR);
> +}
> +
> +/* Clear arbitration lost bit */
> +static void i2c_imx_clr_al_bit(struct imx_i2c_struct *i2c_imx)
> +{
> + unsigned int status;
> +
> + status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
> + status &= ~I2SR_IAL;
> + imx_i2c_write_reg(status, i2c_imx, IMX_I2C_I2SR);
> +}
>
> - return IRQ_NONE;
> +static irqreturn_t i2c_imx_master_isr(struct imx_i2c_struct *i2c_imx)
> +{
> + unsigned int status;
> +
> + dev_dbg(&i2c_imx->adapter.dev, "<%s>: master interrupt\n", __func__);
> +
> + /* Save status register */
> + status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
> + i2c_imx->i2csr = status | I2SR_IIF;
> +
> + wake_up(&i2c_imx->queue);
> +
> + return IRQ_HANDLED;
> }
>
> static int i2c_imx_dma_write(struct imx_i2c_struct *i2c_imx,
> @@ -1043,11 +1063,162 @@ static u32 i2c_imx_func(struct i2c_adapter *adapter)
> | I2C_FUNC_SMBUS_READ_BLOCK_DATA;
> }
>
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> +static void i2c_imx_slave_init(struct imx_i2c_struct *i2c_imx)
> +{
> + unsigned int temp;
> +
> + dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
> +
> + /* Set slave addr. */
> + imx_i2c_write_reg((i2c_imx->slave->addr << 1), i2c_imx, IMX_I2C_IADR);
> +
> + /* Disable i2c module */
> + temp = i2c_imx->hwdata->i2cr_ien_opcode
> + ^ I2CR_IEN;
> + imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
> +
> + /* Reset status register */
> + imx_i2c_write_reg(i2c_imx->hwdata->i2sr_clr_opcode, i2c_imx,
> + IMX_I2C_I2SR);
> +
> + /* Enable module and enable interrupt from i2c module */
> + temp = i2c_imx->hwdata->i2cr_ien_opcode
> + | I2CR_IIEN;
> + imx_i2c_write_reg(temp, i2c_imx, IMX_I2C_I2CR);
> +
> + /* Wait controller to be stable */
> + usleep_range(50, 150);
> +}
> +
> +static irqreturn_t i2c_imx_slave_isr(struct imx_i2c_struct *i2c_imx)
> +{
> + unsigned int status, ctl;
> + u8 value;
> +
> + if (!i2c_imx->slave) {
> + dev_err(&i2c_imx->adapter.dev, "cannot deal with slave irq,i2c_imx->slave is null");
> + return IRQ_NONE;
> + }
> +
> + status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
> + ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
> + if (status & I2SR_IAL) { /* Arbitration lost */
> + i2c_imx_clr_al_bit(i2c_imx);
> + } else if (status & I2SR_IAAS) { /* Addressed as a slave */
> + if (status & I2SR_SRW) { /* Master wants to read from us*/
> + dev_dbg(&i2c_imx->adapter.dev, "read requested");
> + i2c_slave_event(i2c_imx->slave, I2C_SLAVE_READ_REQUESTED, &value);
> +
> + /* Slave transimt */
> + ctl |= I2CR_MTX;
> + imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
> +
> + /* Send data */
> + imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
> + } else { /* Master wants to write to us */
> + dev_dbg(&i2c_imx->adapter.dev, "write requested");
> + i2c_slave_event(i2c_imx->slave, I2C_SLAVE_WRITE_REQUESTED, &value);
> +
> + /* Slave receive */
> + ctl &= ~I2CR_MTX;
> + imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
> + /* Dummy read */
> + value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
> + }
> + } else {
> + if (!(ctl & I2CR_MTX)) { /* Receive mode */
> + if (status & I2SR_IBB) { /* No STOP signal detected */
> + ctl &= ~I2CR_MTX;
> + imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
> +
> + value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
> + i2c_slave_event(i2c_imx->slave, I2C_SLAVE_WRITE_RECEIVED, &value);
> + } else { /* STOP signal is detected */
> + dev_dbg(&i2c_imx->adapter.dev,
> + "STOP signal detected");
> + i2c_slave_event(i2c_imx->slave, I2C_SLAVE_STOP, &value);
> + }
> + } else { /* Transmit mode */
> + if (!(status & I2SR_RXAK)) { /* Received ACK */
> + ctl |= I2CR_MTX;
> + imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
> +
> + i2c_slave_event(i2c_imx->slave, I2C_SLAVE_READ_PROCESSED, &value);
> +
> + imx_i2c_write_reg(value, i2c_imx, IMX_I2C_I2DR);
> + } else { /* Received NAK */
> + ctl &= ~I2CR_MTX;
> + imx_i2c_write_reg(ctl, i2c_imx, IMX_I2C_I2CR);
> + value = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2DR);
> + }
> + }
> + }
> + return IRQ_HANDLED;
> +}
> +
> +static int i2c_imx_reg_slave(struct i2c_client *client)
> +{
> + struct imx_i2c_struct *i2c_imx = i2c_get_adapdata(client->adapter);
> +
> + if (i2c_imx->slave)
> + return -EINVAL;
> +
> + dev_dbg(&i2c_imx->adapter.dev, "<%s>\n", __func__);
> + i2c_imx->slave = client;
> +
> + i2c_imx_slave_init(i2c_imx);
> +
> + return 0;
> +}
> +
> +static int i2c_imx_unreg_slave(struct i2c_client *client)
> +{
> + struct imx_i2c_struct *i2c_imx = i2c_get_adapdata(client->adapter);
> +
> + if (!i2c_imx->slave)
> + return -EINVAL;
> +
> + i2c_imx->slave = NULL;
> +
> + return 0;
> +}
> +#endif /* CONFIG_I2C_SLAVE */
> +
> static const struct i2c_algorithm i2c_imx_algo = {
> .master_xfer = i2c_imx_xfer,
> .functionality = i2c_imx_func,
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> + .reg_slave = i2c_imx_reg_slave,
> + .unreg_slave = i2c_imx_unreg_slave,
> +#endif /* CONFIG_I2C_SLAVE */
> };
>
> +static irqreturn_t i2c_imx_isr(int irq, void *dev_id)
> +{
> + struct imx_i2c_struct *i2c_imx = dev_id;
> + unsigned int status, ctl;
> + irqreturn_t irq_status = IRQ_NONE;
> +
> + status = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2SR);
> + ctl = imx_i2c_read_reg(i2c_imx, IMX_I2C_I2CR);
> +
> + if (status & I2SR_IIF) {
> + i2c_imx_clr_if_bit(i2c_imx);
> +#if IS_ENABLED(CONFIG_I2C_SLAVE)
> + if (ctl & I2CR_MSTA)
> + irq_status = i2c_imx_master_isr(i2c_imx);
> + else
> + irq_status = i2c_imx_slave_isr(i2c_imx);
> +#else
> + irq_status = i2c_imx_master_isr(i2c_imx);
> +
> +#endif /* CONFIG_I2C_SLAVE */
> + }
> +
> + return irq_status;
> +}
> +
> static int i2c_imx_probe(struct platform_device *pdev)
> {
> const struct of_device_id *of_id = of_match_device(i2c_imx_dt_ids,
> --
> 2.17.1
>
[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
[-- Attachment #2: Type: text/plain, Size: 176 bytes --]
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2019-08-08 20:02 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-08-08 3:53 i2c: imx: support slave mode for imx I2C driver Biwen Li
2019-08-08 14:18 ` Sascha Hauer
2019-08-09 4:04 ` [EXT] " Biwen Li
2019-08-12 6:38 ` Sascha Hauer
2019-08-12 7:11 ` Biwen Li
2019-08-08 20:02 ` Wolfram Sang [this message]
2019-08-09 3:18 ` Biwen Li
2019-08-09 15:10 ` Wolfram Sang
2019-08-12 4:22 ` Biwen Li
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190808200202.GA6609@ninjato \
--to=wsa@the-dreams.de \
--cc=biwen.li@nxp.com \
--cc=festevam@gmail.com \
--cc=joshua_frkuska@mentor.com \
--cc=kernel@pengutronix.de \
--cc=laurentiu.tudor@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-imx@nxp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=s.hauer@pengutronix.de \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).