[PATCH] ARM: dts: Update the NSPIRE DTS files for DRM

[Linus Walleij <linus.walleij@linaro.org>]

The DRM subsystem graphics drivers require more granular
definition of the connection between display drivers and
panels, and a proper panel compatible. This utilizes the
bindings merged to the DRM subsystem to properly define
the display on the NSPIRE devices.

We also do away with the undocumented DT binding
"lcd-type".

We add both the clocks to the CLCD block so the driver
have full control over its clocking.

Cc: Daniel Tang <dt.tangr@gmail.com>
Cc: Fabian Vogt <fabian@ritter-vogt.de>
Tested-by: Fabian Vogt <fabian@ritter-vogt.de>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
---
ARM SoC folks:

Please apply this directly for v5.4 DTS changes.
I have negotiated with the NSPIRE maintainers to do
this change.

This is a split from the v3 patch
"ARM: nspire: Move CLCD set-up to device tree"
so you can apply DTS changes separately.
---
 arch/arm/boot/dts/nspire-classic.dtsi | 15 ++++++++++++++-
 arch/arm/boot/dts/nspire-cx.dts       | 15 ++++++++++++++-
 arch/arm/boot/dts/nspire.dtsi         | 10 ++++++++--
 3 files changed, 36 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/nspire-classic.dtsi b/arch/arm/boot/dts/nspire-classic.dtsi
index c53f42777851..41744cc2bc72 100644
--- a/arch/arm/boot/dts/nspire-classic.dtsi
+++ b/arch/arm/boot/dts/nspire-classic.dtsi
@@ -8,7 +8,11 @@
 /include/ "nspire.dtsi"
 
 &lcd {
-	lcd-type = "classic";
+	port {
+		clcd_pads: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
 };
 
 &fast_timer {
@@ -69,6 +73,15 @@
 			#interrupt-cells = <1>;
 		};
 	};
+
+	panel {
+		compatible = "ti,nspire-classic-lcd-panel";
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&clcd_pads>;
+			};
+		};
+	};
 	chosen {
 		bootargs = "debug earlyprintk console=tty0 console=ttyS0,115200n8 root=/dev/ram0";
 	};
diff --git a/arch/arm/boot/dts/nspire-cx.dts b/arch/arm/boot/dts/nspire-cx.dts
index da95c3736651..0c16b04e2744 100644
--- a/arch/arm/boot/dts/nspire-cx.dts
+++ b/arch/arm/boot/dts/nspire-cx.dts
@@ -9,7 +9,11 @@
 /include/ "nspire.dtsi"
 
 &lcd {
-	lcd-type = "cx";
+	port {
+		clcd_pads: endpoint {
+			remote-endpoint = <&panel_in>;
+		};
+	};
 };
 
 &fast_timer {
@@ -106,6 +110,15 @@
 			};
 		};
 	};
+
+	panel {
+		compatible = "ti,nspire-cx-lcd-panel";
+		port {
+			panel_in: endpoint {
+				remote-endpoint = <&clcd_pads>;
+			};
+		};
+	};
 	chosen {
 		bootargs = "debug earlyprintk console=tty0 console=ttyAMA0,115200n8 root=/dev/ram0";
 	};
diff --git a/arch/arm/boot/dts/nspire.dtsi b/arch/arm/boot/dts/nspire.dtsi
index c35fd6667716..d9a0fd7524dc 100644
--- a/arch/arm/boot/dts/nspire.dtsi
+++ b/arch/arm/boot/dts/nspire.dtsi
@@ -95,8 +95,14 @@
 			reg = <0xC0000000 0x1000>;
 			interrupts = <21>;
 
-			clocks = <&apb_pclk>;
-			clock-names = "apb_pclk";
+			/*
+			 * We assume the same clock is fed to APB and CLCDCLK.
+			 * There is some code to scale the clock down by a factor
+			 * 48 for the display so likely the frequency to the
+			 * display is 1MHz and the CLCDCLK is 48 MHz.
+			 */
+			clocks = <&apb_pclk>, <&apb_pclk>;
+			clock-names = "clcdclk", "apb_pclk";
 		};
 
 		adc: adc@C4000000 {
-- 
2.21.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel