Re: [linux-sunxi] [PATCH v8 0/4] Add support for Orange Pi 3

From: Maxime Ripard <maxime.ripard@bootlin.com>
To: Chen-Yu Tsai <wens@csie.org>
Cc: "Ondřej Jirman" <megous@megous.com>,
	"Mark Rutland" <mark.rutland@arm.com>,
	devicetree <devicetree@vger.kernel.org>,
	"David Airlie" <airlied@linux.ie>,
	linux-kernel <linux-kernel@vger.kernel.org>,
	"Jernej Skrabec" <jernej.skrabec@gmail.com>,
	linux-sunxi <linux-sunxi@googlegroups.com>,
	"Rob Herring" <robh+dt@kernel.org>,
	dri-devel <dri-devel@lists.freedesktop.org>,
	"Daniel Vetter" <daniel@ffwll.ch>,
	linux-arm-kernel <linux-arm-kernel@lists.infradead.org>
Subject: Re: [linux-sunxi] [PATCH v8 0/4] Add support for Orange Pi 3
Date: Mon, 12 Aug 2019 10:14:45 +0200	[thread overview]
Message-ID: <20190812081445.kfsbikfrt3pmsh6d@flea> (raw)
In-Reply-To: <CAGb2v67JVG2rhOdUwBmfsO0+RYb4DNOPmUo=Q_UhL3N+niLiEg@mail.gmail.com>

[-- Attachment #1.1: Type: text/plain, Size: 1681 bytes --]

On Mon, Aug 12, 2019 at 03:54:03PM +0800, Chen-Yu Tsai wrote:
> On Mon, Aug 12, 2019 at 3:45 PM Jernej Škrabec <jernej.skrabec@gmail.com> wrote:
> >
> > Dne torek, 06. avgust 2019 ob 17:57:39 CEST je megous@megous.com napisal(a):
> > > From: Ondrej Jirman <megous@megous.com>
> > >
> > > This series implements support for Xunlong Orange Pi 3 board. There
> > > are only a few patches remaining.
> > >
> > > - ethernet support - just a DT change (patch 1)
> > > - HDMI support (patches 2-4)
> > >
> > > For some people, ethernet doesn't work after reboot because u-boot doesn't
> > > support AXP805 PMIC, and will not turn off the etherent PHY regulators.
> > > So the regulator controlled by gpio will be shut down, but the other one
> > > controlled by the AXP PMIC will not.
> > >
> > > This is a problem only when running with a builtin driver. This needs
> > > to be fixed in u-boot.
> > >
> > >
> > > Please take a look.
> >
> > Is there anything missing? It would be nice to get this in 5.4. There is a lot
> > of H6 boards which needs DDC bus enable mechanism (part of H6 reference
> > design), including Beelink GS1 which already has HDMI node in mainline kernel
> > DT, but due to disabled DDC lines works only with 1024x768 (fallback
> > resolution in DRM core).
>
> I have a few minor comments about patch 1.
>
> I think the HDMI bits are good, but I don't have maintainership / commit
> permissions for drm-misc, so I'll have to wait until someone applies patches
> 2 and 3 before I apply patch 4.

I've applied 2,3 and 4

Thanks!
Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel