Re: [PATCH v3 2/6] dt-bindings: usb: dwc3: Add the Amlogic A1 Family DWC3 Glue Bindings

[Rob Herring <robh@kernel.org>]

On Fri, Dec 27, 2019 at 02:36:42PM +0800, Hanjie Lin wrote:
> The Amlogic A1 SoC Family embeds 1 USB Controllers:
>  - a DWC3 IP configured as Host for USB2 and USB3
> 
> A glue connects the controllers to the USB2 PHY of A1 SoC.
> 
> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
> Signed-off-by: Yue Wang <yue.wang@amlogic.com>
> ---
>  .../bindings/usb/amlogic,meson-g12a-usb-ctrl.yaml  | 57 +++++++++++++++++++---
>  1 file changed, 51 insertions(+), 6 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.yaml b/Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.yaml
> index 4efb77b..6103cc2 100644
> --- a/Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.yaml
> +++ b/Documentation/devicetree/bindings/usb/amlogic,meson-g12a-usb-ctrl.yaml
> @@ -9,6 +9,8 @@ title: Amlogic Meson G12A DWC3 USB SoC Controller Glue
>  
>  maintainers:
>    - Neil Armstrong <narmstrong@baylibre.com>
> +  - Hanjie Lin <hanjie.lin@amlogic.com>
> +  - Yue Wang <yue.wang@amlogic.com>
>  
>  description: |
>    The Amlogic G12A embeds a DWC3 USB IP Core configured for USB2 and USB3
> @@ -22,10 +24,14 @@ description: |
>    The DWC3 Glue controls the PHY routing and power, an interrupt line is
>    connected to the Glue to serve as OTG ID change detection.
>  
> +  The Amlogic A1 embeds a DWC3 USB IP Core configured for USB2 in
> +  host-only mode.
> +
>  properties:
>    compatible:
>      enum:
>        - amlogic,meson-g12a-usb-ctrl
> +      - amlogic,meson-a1-usb-ctrl
>  
>    ranges: true
>  
> @@ -37,6 +43,11 @@ properties:
>  
>    clocks:
>      minItems: 1
> +    maxItems: 4
> +
> +  clock-names:
> +    minItems: 1
> +    maxItems: 4
>  
>    resets:
>      minItems: 1
> @@ -47,17 +58,22 @@ properties:
>    interrupts:
>      maxItems: 1
>  
> +  phys:
> +    minItems: 1
> +    maxItems: 3
> +
>    phy-names:
>      items:
>        - const: usb2-phy0 # USB2 PHY0 if USBHOST_A port is used
>        - const: usb2-phy1 # USB2 PHY1 if USBOTG_B port is used
>        - const: usb3-phy0 # USB3 PHY if USB3_0 is used
>  
> -  phys:
> -    minItems: 1
> -    maxItems: 3
> -

Why the unnecessary move?

> -  dr_mode: true
> +  dr_mode:
> +    description: usb mode for G12A
> +    enum:
> +      - host
> +      - peripheral
> +      - otg

No, this is a common property that doesn't need to be redefined here. It 
was correct as-is.

>  
>    power-domains:
>      maxItems: 1
> @@ -80,9 +96,9 @@ required:
>    - resets
>    - reg
>    - interrupts
> -  - phy-names
>    - phys
>    - dr_mode
> +  - phy-names

Again, unnecessary change.

>  
>  examples:
>    - |
> @@ -124,4 +140,33 @@ examples:
>                snps,quirk-frame-length-adjustment;
>            };
>      };
> +  - |
> +    a1_usb: usb@ffe09000 {

You are only adding a compatible. No need for a whole new example.

> +          status = "okay";
> +          compatible = "amlogic,meson-a1-usb-ctrl";
> +          reg = <0 0xffe09000 0x0 0xa0>;
> +          #address-cells = <1>;
> +          #size-cells = <1>;
> +          ranges;
>  
> +          clocks = <&clkc_periphs 36>,
> +                   <&clkc_periphs 85>,
> +                   <&clkc_periphs 2>,
> +                   <&clkc_periphs 3>;
> +          clock-names = "usb_ctrl", "usb_bus", "xtal_usb_phy",
> +                        "xtal_usb_ctrl";
> +
> +          resets = <&reset 36>;
> +
> +          phys = <&usb2_phy1>;
> +          phy-names = "usb2-phy1";
> +
> +          a1_dwc3: usb@ff400000 {
> +                  compatible = "snps,dwc3";
> +                  reg = <0xff400000 0x100000>;
> +                  interrupts = <0 90 4>;
> +                  dr_mode = "host";
> +                  snps,dis_u2_susphy_quirk;
> +                  snps,quirk-frame-length-adjustment = <0x20>;
> +          };
> +    };
> -- 
> 2.7.4
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel