From: Sasha Levin <sashal@kernel.org>
To: linux-kernel@vger.kernel.org, stable@vger.kernel.org
Cc: Sasha Levin <sashal@kernel.org>,
Neil Armstrong <narmstrong@baylibre.com>,
Linus Walleij <linus.walleij@linaro.org>,
linux-gpio@vger.kernel.org, linux-amlogic@lists.infradead.org,
linux-arm-kernel@lists.infradead.org
Subject: [PATCH AUTOSEL 4.19 050/671] pinctrl: meson-gxl: remove invalid GPIOX tsin_a pins
Date: Thu, 16 Jan 2020 11:44:41 -0500 [thread overview]
Message-ID: <20200116165502.8838-50-sashal@kernel.org> (raw)
In-Reply-To: <20200116165502.8838-1-sashal@kernel.org>
From: Neil Armstrong <narmstrong@baylibre.com>
[ Upstream commit d801064cb871806e6843738ecad38993646f53f7 ]
The GPIOX tsin_a pins wrongly uses the SDCard pinctrl bits, this
patch completely removes these pins entries until we find out what
are the correct bits and registers to be used instead.
Fixes: 5a6ae9b80139 ("pinctrl: meson-gxl: add tsin_a pins")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/pinctrl/meson/pinctrl-meson-gxl.c | 12 ++----------
1 file changed, 2 insertions(+), 10 deletions(-)
diff --git a/drivers/pinctrl/meson/pinctrl-meson-gxl.c b/drivers/pinctrl/meson/pinctrl-meson-gxl.c
index 158f618f1695..0c0a5018102b 100644
--- a/drivers/pinctrl/meson/pinctrl-meson-gxl.c
+++ b/drivers/pinctrl/meson/pinctrl-meson-gxl.c
@@ -239,13 +239,9 @@ static const unsigned int eth_link_led_pins[] = { GPIOZ_14 };
static const unsigned int eth_act_led_pins[] = { GPIOZ_15 };
static const unsigned int tsin_a_d0_pins[] = { GPIODV_0 };
-static const unsigned int tsin_a_d0_x_pins[] = { GPIOX_10 };
static const unsigned int tsin_a_clk_pins[] = { GPIODV_8 };
-static const unsigned int tsin_a_clk_x_pins[] = { GPIOX_11 };
static const unsigned int tsin_a_sop_pins[] = { GPIODV_9 };
-static const unsigned int tsin_a_sop_x_pins[] = { GPIOX_8 };
static const unsigned int tsin_a_d_valid_pins[] = { GPIODV_10 };
-static const unsigned int tsin_a_d_valid_x_pins[] = { GPIOX_9 };
static const unsigned int tsin_a_fail_pins[] = { GPIODV_11 };
static const unsigned int tsin_a_dp_pins[] = {
GPIODV_1, GPIODV_2, GPIODV_3, GPIODV_4, GPIODV_5, GPIODV_6, GPIODV_7,
@@ -432,10 +428,6 @@ static struct meson_pmx_group meson_gxl_periphs_groups[] = {
GROUP(spi_miso, 5, 2),
GROUP(spi_ss0, 5, 1),
GROUP(spi_sclk, 5, 0),
- GROUP(tsin_a_sop_x, 6, 3),
- GROUP(tsin_a_d_valid_x, 6, 2),
- GROUP(tsin_a_d0_x, 6, 1),
- GROUP(tsin_a_clk_x, 6, 0),
/* Bank Z */
GROUP(eth_mdio, 4, 23),
@@ -698,8 +690,8 @@ static const char * const eth_led_groups[] = {
};
static const char * const tsin_a_groups[] = {
- "tsin_a_clk", "tsin_a_clk_x", "tsin_a_sop", "tsin_a_sop_x",
- "tsin_a_d_valid", "tsin_a_d_valid_x", "tsin_a_d0", "tsin_a_d0_x",
+ "tsin_a_clk", "tsin_a_sop",
+ "tsin_a_d_valid", "tsin_a_d0",
"tsin_a_dp", "tsin_a_fail",
};
--
2.20.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-01-16 17:02 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20200116165502.8838-1-sashal@kernel.org>
2020-01-16 16:43 ` [PATCH AUTOSEL 4.19 002/671] ARM: dts: at91: nattis: set the PRLUD and HIPOW signals low Sasha Levin
2020-01-16 16:43 ` [PATCH AUTOSEL 4.19 003/671] ARM: dts: at91: nattis: make the SD-card slot work Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 010/671] ARM: qcom_defconfig: Enable MAILBOX Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 012/671] PCI: iproc: Remove PAXC slot check to allow VF support Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 018/671] mailbox: mediatek: Add check for possible failure of kzalloc Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 041/671] drm/sun4i: hdmi: Fix double flag assignation Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 047/671] ARM: dts: bcm283x: Correct mailbox register sizes Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 049/671] ASoC: sun8i-codec: add missing route for ADC Sasha Levin
2020-01-16 16:44 ` Sasha Levin [this message]
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 057/671] arm64: dts: meson-gx: Add hdmi_5v regulator as hdmi tx supply Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 064/671] staging: bcm2835-camera: Abort probe if there is no camera Sasha Levin
2020-01-16 16:44 ` [PATCH AUTOSEL 4.19 065/671] staging: bcm2835-camera: fix module autoloading Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 088/671] clk: samsung: exynos4: fix refcount leak in exynos4_get_xom() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 089/671] clk: imx6q: fix refcount leak in imx6q_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 090/671] clk: imx6sx: fix refcount leak in imx6sx_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 091/671] clk: imx7d: fix refcount leak in imx7d_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 092/671] clk: vf610: fix refcount leak in vf610_clocks_init() Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 098/671] MIPS: BCM63XX: drop unused and broken DSP platform device Sasha Levin
2020-01-16 16:45 ` [PATCH AUTOSEL 4.19 099/671] arm64: defconfig: Re-enable bcm2835-thermal driver Sasha Levin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200116165502.8838-50-sashal@kernel.org \
--to=sashal@kernel.org \
--cc=linus.walleij@linaro.org \
--cc=linux-amlogic@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=narmstrong@baylibre.com \
--cc=stable@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).