[PATCH v2 1/3] dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml

* [PATCH v2 1/3] dt-bindings: mmc: convert synopsys dw-mshc bindings to yaml
@ 2020-01-16 15:22 Johan Jonker
  2020-01-16 15:22 ` [PATCH v2 2/3] dt-bindings: mmc: convert rockchip " Johan Jonker
                   ` (3 more replies)
  0 siblings, 4 replies; 9+ messages in thread
From: Johan Jonker @ 2020-01-16 15:22 UTC (permalink / raw)
  To: ulf.hansson
  Cc: mark.rutland, devicetree, heiko, linux-mmc, linux-kernel,
	linux-rockchip, robh+dt, linux-arm-kernel

Current dts files with 'dwmmc' nodes are manually verified.
In order to automate this process synopsys-dw-mshc.txt
has to be converted to yaml. In the new setup
synopsys-dw-mshc.yaml will inherit properties from
mmc-controller.yaml and synopsys-dw-mshc-common.yaml.
'dwmmc' will no longer be a valid name for a node and
should be changed to 'mmc'.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
---
 .../bindings/mmc/synopsys-dw-mshc-common.yaml      |  68 ++++++++++
 .../devicetree/bindings/mmc/synopsys-dw-mshc.txt   | 141 ---------------------
 .../devicetree/bindings/mmc/synopsys-dw-mshc.yaml  |  70 ++++++++++
 3 files changed, 138 insertions(+), 141 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml
 delete mode 100644 Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
 create mode 100644 Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml

diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml
new file mode 100644
index 000000000..890d47a87
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc-common.yaml
@@ -0,0 +1,68 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/synopsys-dw-mshc-common.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys Designware Mobile Storage Host Controller Common Properties
+
+allOf:
+  - $ref: "mmc-controller.yaml#"
+
+maintainers:
+  - Ulf Hansson <ulf.hansson@linaro.org>
+
+# Everything else is described in the common file
+properties:
+  resets:
+    maxItems: 1
+
+  reset-names:
+    const: reset
+
+  clock-frequency:
+    description:
+      Should be the frequency (in Hz) of the ciu clock.  If this
+      is specified and the ciu clock is specified then we'll try to set the ciu
+      clock to this at probe time.
+
+  fifo-depth:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      The maximum size of the tx/rx fifo's. If this property is not
+      specified, the default value of the fifo size is determined from the
+      controller registers.
+
+  card-detect-delay:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+      - default: 0
+    description:
+      Delay in milli-seconds before detecting card after card
+      insert event. The default value is 0.
+
+  data-addr:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/uint32
+    description:
+      Override fifo address with value provided by DT. The default FIFO reg
+      offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A)
+      by driver. If the controller does not follow this rule, please use
+      this property to set fifo address in device tree.
+
+  fifo-watermark-aligned:
+    allOf:
+      - $ref: /schemas/types.yaml#/definitions/flag
+    description:
+      Data done irq is expected if data length is less than
+      watermark in PIO mode. But fifo watermark is requested to be aligned
+      with data length in some SoC so that TX/RX irq can be generated with
+      data done irq. Add this watermark quirk to mark this requirement and
+      force fifo watermark setting accordingly.
+
+  dmas:
+    maxItems: 1
+
+  dma-names:
+    const: rx-tx
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
deleted file mode 100644
index 7e5e427a2..000000000
--- a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.txt
+++ /dev/null
@@ -1,141 +0,0 @@
-* Synopsys Designware Mobile Storage Host Controller
-
-The Synopsys designware mobile storage host controller is used to interface
-a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
-differences between the core mmc properties described by mmc.txt and the
-properties used by the Synopsys Designware Mobile Storage Host Controller.
-
-Required Properties:
-
-* compatible: should be
-	- snps,dw-mshc: for controllers compliant with synopsys dw-mshc.
-* #address-cells: should be 1.
-* #size-cells: should be 0.
-
-# Slots (DEPRECATED): The slot specific information are contained within
-  child-nodes with each child-node representing a supported slot. There should
-  be atleast one child node representing a card slot. The name of the child node
-  representing the slot is recommended to be slot@n where n is the unique number
-  of the slot connected to the controller. The following are optional properties
-  which can be included in the slot child node.
-
-	* reg: specifies the physical slot number. The valid values of this
-	  property is 0 to (num-slots -1), where num-slots is the value
-	  specified by the num-slots property.
-
-	* bus-width: as documented in mmc core bindings.
-
-	* wp-gpios: specifies the write protect gpio line. The format of the
-	  gpio specifier depends on the gpio controller. If a GPIO is not used
-	  for write-protect, this property is optional.
-
-	* disable-wp: If the wp-gpios property isn't present then (by default)
-	  we'd assume that the write protect is hooked up directly to the
-	  controller's special purpose write protect line (accessible via
-	  the WRTPRT register).  However, it's possible that we simply don't
-	  want write protect.  In that case specify 'disable-wp'.
-	  NOTE: This property is not required for slots known to always
-	  connect to eMMC or SDIO cards.
-
-Optional properties:
-
-* resets: phandle + reset specifier pair, intended to represent hardware
-  reset signal present internally in some host controller IC designs.
-  See Documentation/devicetree/bindings/reset/reset.txt for details.
-
-* reset-names: request name for using "resets" property. Must be "reset".
-	(It will be used together with "resets" property.)
-
-* clocks: from common clock binding: handle to biu and ciu clocks for the
-  bus interface unit clock and the card interface unit clock.
-
-* clock-names: from common clock binding: Shall be "biu" and "ciu".
-  If the biu clock is missing we'll simply skip enabling it.  If the
-  ciu clock is missing we'll just assume that the clock is running at
-  clock-frequency.  It is an error to omit both the ciu clock and the
-  clock-frequency.
-
-* clock-frequency: should be the frequency (in Hz) of the ciu clock.  If this
-  is specified and the ciu clock is specified then we'll try to set the ciu
-  clock to this at probe time.
-
-* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not
-  specified, the default value of the fifo size is determined from the
-  controller registers.
-
-* card-detect-delay: Delay in milli-seconds before detecting card after card
-  insert event. The default value is 0.
-
-* data-addr: Override fifo address with value provided by DT. The default FIFO reg
-  offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
-  driver. If the controller does not follow this rule, please use this property
-  to set fifo address in device tree.
-
-* fifo-watermark-aligned: Data done irq is expected if data length is less than
-  watermark in PIO mode. But fifo watermark is requested to be aligned with data
-  length in some SoC so that TX/RX irq can be generated with data done irq. Add this
-  watermark quirk to mark this requirement and force fifo watermark setting
-  accordingly.
-
-* vmmc-supply: The phandle to the regulator to use for vmmc.  If this is
-  specified we'll defer probe until we can find this regulator.
-
-* dmas: List of DMA specifiers with the controller specific format as described
-  in the generic DMA client binding. Refer to dma.txt for details.
-
-* dma-names: request names for generic DMA client binding. Must be "rx-tx".
-  Refer to dma.txt for details.
-
-Aliases:
-
-- All the MSHC controller nodes should be represented in the aliases node using
-  the following format 'mshc{n}' where n is a unique number for the alias.
-
-Example:
-
-The MSHC controller node can be split into two portions, SoC specific and
-board specific portions as listed below.
-
-	dwmmc0@12200000 {
-		compatible = "snps,dw-mshc";
-		clocks = <&clock 351>, <&clock 132>;
-		clock-names = "biu", "ciu";
-		reg = <0x12200000 0x1000>;
-		interrupts = <0 75 0>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		data-addr = <0x200>;
-		fifo-watermark-aligned;
-		resets = <&rst 20>;
-		reset-names = "reset";
-	};
-
-[board specific internal DMA resources]
-
-	dwmmc0@12200000 {
-		clock-frequency = <400000000>;
-		clock-freq-min-max = <400000 200000000>;
-		broken-cd;
-		fifo-depth = <0x80>;
-		card-detect-delay = <200>;
-		vmmc-supply = <&buck8>;
-		bus-width = <8>;
-		cap-mmc-highspeed;
-		cap-sd-highspeed;
-	};
-
-[board specific generic DMA request binding]
-
-	dwmmc0@12200000 {
-		clock-frequency = <400000000>;
-		clock-freq-min-max = <400000 200000000>;
-		broken-cd;
-		fifo-depth = <0x80>;
-		card-detect-delay = <200>;
-		vmmc-supply = <&buck8>;
-		bus-width = <8>;
-		cap-mmc-highspeed;
-		cap-sd-highspeed;
-		dmas = <&pdma 12>;
-		dma-names = "rx-tx";
-	};
diff --git a/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml
new file mode 100644
index 000000000..05f9f36dc
--- /dev/null
+++ b/Documentation/devicetree/bindings/mmc/synopsys-dw-mshc.yaml
@@ -0,0 +1,70 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mmc/synopsys-dw-mshc.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Synopsys Designware Mobile Storage Host Controller Binding
+
+allOf:
+  - $ref: "synopsys-dw-mshc-common.yaml#"
+
+maintainers:
+  - Ulf Hansson <ulf.hansson@linaro.org>
+
+# Everything else is described in the common file
+properties:
+  compatible:
+    const: snps,dw-mshc
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    minItems: 2
+    maxItems: 2
+    description:
+      Handle to "biu" and "ciu" clocks for the
+      bus interface unit clock and the card interface unit clock.
+
+  clock-names:
+    items:
+      - const: biu
+      - const: ciu
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+  - clock-names
+
+examples:
+  - |
+    mmc@12200000 {
+      compatible = "snps,dw-mshc";
+      reg = <0x12200000 0x1000>;
+      interrupts = <0 75 0>;
+      clocks = <&clock 351>, <&clock 132>;
+      clock-names = "biu", "ciu";
+      dmas = <&pdma 12>;
+      dma-names = "rx-tx";
+      resets = <&rst 20>;
+      reset-names = "reset";
+      vmmc-supply = <&buck8>;
+      #address-cells = <1>;
+      #size-cells = <0>;
+      broken-cd;
+      bus-width = <8>;
+      cap-mmc-highspeed;
+      cap-sd-highspeed;
+      card-detect-delay = <200>;
+      clock-freq-min-max = <400000 200000000>;
+      clock-frequency = <400000000>;
+      data-addr = <0x200>;
+      fifo-depth = <0x80>;
+      fifo-watermark-aligned;
+    };
-- 
2.11.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

^ permalink raw reply related	[flat|nested] 9+ messages in thread