From: Russell King - ARM Linux admin <linux@armlinux.org.uk>
To: Stefan Lehner <stefan-lehner@aon.at>
Cc: linux-arm-kernel@lists.infradead.org
Subject: Re: StrongARM SA-1110 / SA-1111 and Kernel 4.9.210 (Jornada 720)
Date: Fri, 7 Feb 2020 23:19:46 +0000 [thread overview]
Message-ID: <20200207231946.GZ25745@shell.armlinux.org.uk> (raw)
In-Reply-To: <002d01d5ddac$fc6f6590$f54e30b0$@at>
Hi,
Hmm, if you enable early printk, can you then get the kernel boot
messages?
Enable CONFIG_EARLY_PRINTK, and then supply "earlyprintk" on the
kernel command line.
Thanks.
On Fri, Feb 07, 2020 at 12:51:51PM +0100, Stefan Lehner wrote:
> Hello!
> I tested it with both options enabled and it makes no difference. No error
> messages during boot. The kernel compiles fine!
>
> Regards
> Stefan
>
>
>
>
> -----Ursprüngliche Nachricht-----
> Von: linux-arm-kernel [mailto:linux-arm-kernel-bounces@lists.infradead.org]
> Im Auftrag von Russell King - ARM Linux admin
> Gesendet: Mittwoch, 22. Jänner 2020 11:25
> An: Stefan Lehner
> Cc: linux-arm-kernel@lists.infradead.org
> Betreff: Re: StrongARM SA-1110 / SA-1111 and Kernel 4.9.210 (Jornada 720)
>
> On Wed, Jan 22, 2020 at 11:21:36AM +0100, Stefan Lehner wrote:
> >
> > On Wed, Jan 22, 2020 at 09:10:13AM +0100, Stefan Lehner wrote:
> > > Hi!
> > > I like to get a newer Linux Kernel running on my Jornada 720. It has a
> > > StrongArm SA-1110 CPU and the SA-1111 companion chip.
> > > I patched the kernel source with the BX emulation to run a newer Debian
> > > userland. The kernel compiled fine.
> > > It starts to boot on the Jornada with the linexec bootloader. But it
> seems
> > > that it doesnt detect any CF or PCMCIA card. I managed to get the
> > > jornada720_pcmcia_configure_socket() running and it detects the card and
> > > powers it up with the correct voltage (3V for the CF card in socket 1).
> >
> > >> What was required for that?
> >
> > I had to comment out:
> > # CONFIG_PCMCIA_SA1100 is not set
> > and activate:
> > CONFIG_PCMCIA_SA1111=y
> > in the kernel .config.
>
> Yes, you'll need CONFIG_PCMCIA_SA1111 set, because the Jornada720 uses
> the companion chip. CONFIG_PCMCIA_SA1100 should make no difference, so
> can we spend some time working out why you needed to disable it?
>
> Did you get any error messages during boot with both enabled?
>
> --
> RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
> FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps
> up
> According to speedtest.net: 11.9Mbps down 500kbps up
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
--
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTC broadband for 0.8mile line in suburbia: sync at 12.1Mbps down 622kbps up
According to speedtest.net: 11.9Mbps down 500kbps up
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-02-07 23:20 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-22 8:10 StrongARM SA-1110 / SA-1111 and Kernel 4.9.210 (Jornada 720) Stefan Lehner
2020-01-22 9:22 ` Russell King - ARM Linux admin
2020-01-22 10:21 ` Stefan Lehner
2020-01-22 10:25 ` Russell King - ARM Linux admin
2020-01-23 16:24 ` AW: " Stefan Lehner
2020-02-07 11:51 ` Stefan Lehner
2020-02-07 23:19 ` Russell King - ARM Linux admin [this message]
2020-02-08 7:54 ` Stefan Lehner
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200207231946.GZ25745@shell.armlinux.org.uk \
--to=linux@armlinux.org.uk \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=stefan-lehner@aon.at \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).