[PATCH 5.5 130/399] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3

[PATCH 5.5 130/399] ARM: dts: imx6: rdu2: Disable WP for USDHC2 and USDHC3

[Greg Kroah-Hartman]

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit cd58a174e58649426fb43d7456e5f7d7eab58af1 ]

RDU2 production units come with resistor connecting WP pin to
correpsonding GPIO DNPed for both SD card slots. Drop any WP related
configuration and mark both slots with "disable-wp".

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 6 ++----
 1 file changed, 2 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
index a2a4f33a3e3ef..4ec9fb332610e 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@@ -629,7 +629,7 @@
 	pinctrl-0 = <&pinctrl_usdhc2>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 2 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 3 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
@@ -642,7 +642,7 @@
 	pinctrl-0 = <&pinctrl_usdhc3>;
 	bus-width = <4>;
 	cd-gpios = <&gpio2 0 GPIO_ACTIVE_LOW>;
-	wp-gpios = <&gpio2 1 GPIO_ACTIVE_HIGH>;
+	disable-wp;
 	vmmc-supply = <&reg_3p3v_sd>;
 	vqmmc-supply = <&reg_3p3v>;
 	no-1-8-v;
@@ -1056,7 +1056,6 @@
 			MX6QDL_PAD_SD2_DAT1__SD2_DATA1		0x17059
 			MX6QDL_PAD_SD2_DAT2__SD2_DATA2		0x17059
 			MX6QDL_PAD_SD2_DAT3__SD2_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D3__GPIO2_IO03		0x40010040
 			MX6QDL_PAD_NANDF_D2__GPIO2_IO02		0x40010040
 		>;
 	};
@@ -1069,7 +1068,6 @@
 			MX6QDL_PAD_SD3_DAT1__SD3_DATA1		0x17059
 			MX6QDL_PAD_SD3_DAT2__SD3_DATA2		0x17059
 			MX6QDL_PAD_SD3_DAT3__SD3_DATA3		0x17059
-			MX6QDL_PAD_NANDF_D1__GPIO2_IO01		0x40010040
 			MX6QDL_PAD_NANDF_D0__GPIO2_IO00		0x40010040
 
 		>;
-- 
2.20.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.5 131/399] ARM: dts: imx6: rdu2: Limit USBH1 to Full Speed

[Greg Kroah-Hartman]

From: Andrey Smirnov <andrew.smirnov@gmail.com>

[ Upstream commit 6bb1e09c4c375db29770444f689f35f5cbe696bc ]

Cabling used to connect devices to USBH1 on RDU2 does not meet USB
spec cable quality and cable length requirements to operate at High
Speed, so limit the port to Full Speed only.

Reported-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
index 4ec9fb332610e..cbafadbe86f45 100644
--- a/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-zii-rdu2.dtsi
@@ -776,6 +776,7 @@
 &usbh1 {
 	vbus-supply = <&reg_5p0v_main>;
 	disable-over-current;
+	maximum-speed = "full-speed";
 	status = "okay";
 };
 
-- 
2.20.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel