From: Shawn Guo <shawnguo@kernel.org>
To: Li Yang <leoyang.li@nxp.com>
Cc: linux-kernel@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 06/15] arm64: defconfig: Enable NXP/FSL SPI controller drivers
Date: Wed, 11 Mar 2020 13:51:06 +0800 [thread overview]
Message-ID: <20200311055104.GA29269@dragon> (raw)
In-Reply-To: <1582585690-463-7-git-send-email-leoyang.li@nxp.com>
On Mon, Feb 24, 2020 at 05:08:01PM -0600, Li Yang wrote:
> Enables SPI controller drivers used in various NXP/FSL SoCs.
>
> Enabled as built-in to load RFS from SPI flash without requiring
> initramfs.
RootFS on SPI flash? On which platforms?
Shawn
>
> Signed-off-by: Li Yang <leoyang.li@nxp.com>
> ---
> arch/arm64/configs/defconfig | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index 7390c8f3838d..e97ef8b944b8 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -398,8 +398,11 @@ CONFIG_SPI=y
> CONFIG_SPI_ARMADA_3700=y
> CONFIG_SPI_BCM2835=m
> CONFIG_SPI_BCM2835AUX=m
> +CONFIG_SPI_FSL_LPSPI=y
> +CONFIG_SPI_FSL_QUADSPI=y
> CONFIG_SPI_NXP_FLEXSPI=y
> CONFIG_SPI_IMX=m
> +CONFIG_SPI_FSL_DSPI=y
> CONFIG_SPI_MESON_SPICC=m
> CONFIG_SPI_MESON_SPIFC=m
> CONFIG_SPI_ORION=y
> --
> 2.17.1
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-03-11 5:51 UTC|newest]
Thread overview: 24+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-02-24 23:07 [PATCH 00/15] Enable drivers for NXP/FSL QorIQ arm64 boards Li Yang
2020-02-24 23:07 ` [PATCH 01/15] arm64: defconfig: run through savedefconfig for ordering Li Yang
2020-02-24 23:07 ` [PATCH 02/15] arm64: defconfig: Enable NXP flexcan driver Li Yang
2020-02-24 23:07 ` [PATCH 03/15] arm64: defconfig: Enable QorIQ DPAA1 drivers Li Yang
2020-02-24 23:07 ` [PATCH 04/15] arm64: defconfig: Enable QorIQ DPAA2 drivers Li Yang
2020-02-24 23:08 ` [PATCH 05/15] arm64: defconfig: Enable ENETC Ethernet controller and FELIX switch Li Yang
2020-02-24 23:08 ` [PATCH 06/15] arm64: defconfig: Enable NXP/FSL SPI controller drivers Li Yang
2020-03-11 5:51 ` Shawn Guo [this message]
[not found] ` <CADRPPNQ-VWmVMdBuEUj9RdXAYvt4dhy+scP-EaYbrXj3McSaVQ@mail.gmail.com>
2020-03-11 7:06 ` Shawn Guo
2020-02-24 23:08 ` [PATCH 07/15] arm64: defconfig: Enable QorIQ cpufreq driver Li Yang
2020-03-11 6:12 ` Shawn Guo
2020-03-11 18:54 ` Leo Li
2020-03-12 14:22 ` Shawn Guo
2020-03-12 16:31 ` Leo Li
2020-02-24 23:08 ` [PATCH 08/15] arm64: defconfig: Enable ARM SBSA watchdog driver Li Yang
2020-02-24 23:08 ` [PATCH 09/15] arm64: defconfig: Enable QorIQ IFC NAND controller driver Li Yang
2020-03-11 6:13 ` Shawn Guo
2020-03-11 18:55 ` Leo Li
2020-02-24 23:08 ` [PATCH 10/15] arm64: defconfig: Enable QorIQ GPIO driver Li Yang
2020-02-24 23:08 ` [PATCH 11/15] arm64: defconfig: Enable ARM Mali display driver Li Yang
2020-02-24 23:08 ` [PATCH 12/15] arm64: defconfig: Enable flash device drivers for QorIQ boards Li Yang
2020-02-24 23:08 ` [PATCH 13/15] arm64: defconfig: Enable RTC devices " Li Yang
2020-02-24 23:08 ` [PATCH 14/15] arm64: defconfig: Enable PHY devices used on " Li Yang
2020-02-24 23:08 ` [PATCH 15/15] arm64: defconfig: Enable e1000 device Li Yang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200311055104.GA29269@dragon \
--to=shawnguo@kernel.org \
--cc=leoyang.li@nxp.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).