[PATCH 1/2] ARM: dts: imx6qdl-sabresd: Pass phy-reset-duration

[PATCH 1/2] ARM: dts: imx6qdl-sabresd: Pass phy-reset-duration

[Fabio Estevam]

According to the AR8031 datasheet:

"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."

Pass the 'phy-reset-duration' property to meet such requirement.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 28b35ccb3757..9697211b7693 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -204,6 +204,7 @@
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
+	phy-reset-duration = <10>;
 	fsl,magic-packet;
 	status = "okay";
 };
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/2] ARM: dts: imx6qdl-sabresd: Add an mdio node

[Fabio Estevam]

imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.

The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.

Improve the Ethernet representation by adding an mdio node with such
information.

An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
---
 arch/arm/boot/dts/imx6qdl-sabresd.dtsi | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
index 9697211b7693..fb70ae0811af 100644
--- a/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-sabresd.dtsi
@@ -203,10 +203,21 @@
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_enet>;
 	phy-mode = "rgmii-id";
+	phy-handle = <&phy>;
 	phy-reset-gpios = <&gpio1 25 GPIO_ACTIVE_LOW>;
 	phy-reset-duration = <10>;
 	fsl,magic-packet;
 	status = "okay";
+
+	mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		phy: ethernet-phy@1 {
+			reg = <1>;
+			qca,clk-out-frequency = <125000000>;
+		};
+	};
 };
 
 &hdmi {
-- 
2.17.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel