[PATCH 5.4 014/314] ARM: dts: stm32: Add missing ethernet PHY reset on AV96

[PATCH 5.4 014/314] ARM: dts: stm32: Add missing ethernet PHY reset on AV96

[Greg Kroah-Hartman]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 010ca9fe500bfe365860b50220ff80541c18f0e1 ]

Add PHY reset GPIO on AV96 ethernet PHY.

Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157a-avenger96.dts | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/stm32mp157a-avenger96.dts b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
index 2e4742c53d048..7b8c3f25861c9 100644
--- a/arch/arm/boot/dts/stm32mp157a-avenger96.dts
+++ b/arch/arm/boot/dts/stm32mp157a-avenger96.dts
@@ -91,6 +91,9 @@
 		#address-cells = <1>;
 		#size-cells = <0>;
 		compatible = "snps,dwmac-mdio";
+		reset-gpios = <&gpioz 2 GPIO_ACTIVE_LOW>;
+		reset-delay-us = <1000>;
+
 		phy0: ethernet-phy@7 {
 			reg = <7>;
 		};
-- 
2.25.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.4 031/314] serial: 8250: Fix max baud limit in generic 8250 port

[Greg Kroah-Hartman]

From: Serge Semin <Sergey.Semin@baikalelectronics.ru>

[ Upstream commit 7b668c064ec33f3d687c3a413d05e355172e6c92 ]

Standard 8250 UART ports are designed in a way so they can communicate
with baud rates up to 1/16 of a reference frequency. It's expected from
most of the currently supported UART controllers. That's why the former
version of serial8250_get_baud_rate() method called uart_get_baud_rate()
with min and max baud rates passed as (port->uartclk / 16 / UART_DIV_MAX)
and ((port->uartclk + tolerance) / 16) respectively. Doing otherwise, like
it was suggested in commit ("serial: 8250_mtk: support big baud rate."),
caused acceptance of bauds, which was higher than the normal UART
controllers actually supported. As a result if some user-space program
requested to set a baud greater than (uartclk / 16) it would have been
permitted without truncation, but then serial8250_get_divisor(baud)
(which calls uart_get_divisor() to get the reference clock divisor) would
have returned a zero divisor. Setting zero divisor will cause an
unpredictable effect varying from chip to chip. In case of DW APB UART the
communications just stop.

Lets fix this problem by getting back the limitation of (uartclk +
tolerance) / 16 maximum baud supported by the generic 8250 port. Mediatek
8250 UART ports driver developer shouldn't have touched it in the first
place  notably seeing he already provided a custom version of set_termios()
callback in that glue-driver which took into account the extended baud
rate values and accordingly updated the standard and vendor-specific
divisor latch registers anyway.

Fixes: 81bb549fdf14 ("serial: 8250_mtk: support big baud rate.")
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Cc: Alexey Malahov <Alexey.Malahov@baikalelectronics.ru>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Paul Burton <paulburton@kernel.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Long Cheng <long.cheng@mediatek.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: linux-mips@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/20200506233136.11842-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/tty/serial/8250/8250_port.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/tty/serial/8250/8250_port.c b/drivers/tty/serial/8250/8250_port.c
index 2c65c775bf5aa..dbb27303a6b49 100644
--- a/drivers/tty/serial/8250/8250_port.c
+++ b/drivers/tty/serial/8250/8250_port.c
@@ -2539,6 +2539,8 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
 					     struct ktermios *termios,
 					     struct ktermios *old)
 {
+	unsigned int tolerance = port->uartclk / 100;
+
 	/*
 	 * Ask the core to calculate the divisor for us.
 	 * Allow 1% tolerance at the upper limit so uart clks marginally
@@ -2547,7 +2549,7 @@ static unsigned int serial8250_get_baud_rate(struct uart_port *port,
 	 */
 	return uart_get_baud_rate(port, termios, old,
 				  port->uartclk / 16 / UART_DIV_MAX,
-				  port->uartclk);
+				  (port->uartclk + tolerance) / 16);
 }
 
 void
-- 
2.25.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.4 153/314] usb/ohci-platform: Fix a warning when hibernating

[Greg Kroah-Hartman]

From: Qais Yousef <qais.yousef@arm.com>

[ Upstream commit 1cb3b0095c3d0bb96912bfbbce4fc006d41f367c ]

The following warning was observed when attempting to suspend to disk
using a USB flash as a swap device.

[  111.779649] ------------[ cut here ]------------
[  111.788382] URB (____ptrval____) submitted while active
[  111.796646] WARNING: CPU: 3 PID: 365 at drivers/usb/core/urb.c:363 usb_submit_urb+0x3d8/0x590
[  111.805417] Modules linked in:
[  111.808584] CPU: 3 PID: 365 Comm: kworker/3:2 Not tainted 5.6.0-rc6-00002-gdfd1731f9a3e-dirty #545
[  111.817796] Hardware name: ARM Juno development board (r2) (DT)
[  111.823896] Workqueue: usb_hub_wq hub_event
[  111.828217] pstate: 60000005 (nZCv daif -PAN -UAO)
[  111.833156] pc : usb_submit_urb+0x3d8/0x590
[  111.837471] lr : usb_submit_urb+0x3d8/0x590
[  111.841783] sp : ffff800018de38b0
[  111.845205] x29: ffff800018de38b0 x28: 0000000000000003
[  111.850682] x27: ffff000970530b20 x26: ffff8000133fd000
[  111.856159] x25: ffff8000133fd000 x24: ffff800018de3b38
[  111.861635] x23: 0000000000000004 x22: 0000000000000c00
[  111.867112] x21: 0000000000000000 x20: 00000000fffffff0
[  111.872589] x19: ffff0009704e7a00 x18: ffffffffffffffff
[  111.878065] x17: 00000000a7c8f4bc x16: 000000002af33de8
[  111.883542] x15: ffff8000133fda88 x14: 0720072007200720
[  111.889019] x13: 0720072007200720 x12: 0720072007200720
[  111.894496] x11: 0000000000000000 x10: 00000000a5286134
[  111.899973] x9 : 0000000000000002 x8 : ffff000970c837a0
[  111.905449] x7 : 0000000000000000 x6 : ffff800018de3570
[  111.910926] x5 : 0000000000000001 x4 : 0000000000000003
[  111.916401] x3 : 0000000000000000 x2 : ffff800013427118
[  111.921879] x1 : 9d4e965b4b7d7c00 x0 : 0000000000000000
[  111.927356] Call trace:
[  111.929892]  usb_submit_urb+0x3d8/0x590
[  111.933852]  hub_activate+0x108/0x7f0
[  111.937633]  hub_resume+0xac/0x148
[  111.941149]  usb_resume_interface.isra.10+0x60/0x138
[  111.946265]  usb_resume_both+0xe4/0x140
[  111.950225]  usb_runtime_resume+0x24/0x30
[  111.954365]  __rpm_callback+0xdc/0x138
[  111.958236]  rpm_callback+0x34/0x98
[  111.961841]  rpm_resume+0x4a8/0x720
[  111.965445]  rpm_resume+0x50c/0x720
[  111.969049]  __pm_runtime_resume+0x4c/0xb8
[  111.973276]  usb_autopm_get_interface+0x28/0x60
[  111.977948]  hub_event+0x80/0x16d8
[  111.981466]  process_one_work+0x2a4/0x748
[  111.985604]  worker_thread+0x48/0x498
[  111.989387]  kthread+0x13c/0x140
[  111.992725]  ret_from_fork+0x10/0x18
[  111.996415] irq event stamp: 354
[  111.999756] hardirqs last  enabled at (353): [<ffff80001019ea1c>] console_unlock+0x504/0x5b8
[  112.008441] hardirqs last disabled at (354): [<ffff8000100a95d0>] do_debug_exception+0x1a8/0x258
[  112.017479] softirqs last  enabled at (350): [<ffff8000100818a4>] __do_softirq+0x4bc/0x568
[  112.025984] softirqs last disabled at (343): [<ffff8000101145a4>] irq_exit+0x144/0x150
[  112.034129] ---[ end trace dc96030b9cf6c8a3 ]---

The problem was tracked down to a missing call to
pm_runtime_set_active() on resume in ohci-platform.

Link: https://lore.kernel.org/lkml/20200323143857.db5zphxhq4hz3hmd@e107158-lin.cambridge.arm.com/
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
CC: Tony Prisk <linux@prisktech.co.nz>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: Oliver Neukum <oneukum@suse.de>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20200518154931.6144-1-qais.yousef@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/host/ohci-platform.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/usb/host/ohci-platform.c b/drivers/usb/host/ohci-platform.c
index 7addfc2cbadce..4a8456f12a73d 100644
--- a/drivers/usb/host/ohci-platform.c
+++ b/drivers/usb/host/ohci-platform.c
@@ -299,6 +299,11 @@ static int ohci_platform_resume(struct device *dev)
 	}
 
 	ohci_resume(hcd, false);
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
 	return 0;
 }
 #endif /* CONFIG_PM_SLEEP */
-- 
2.25.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.4 195/314] misc: xilinx-sdfec: improve get_user_pages_fast() error handling

[Greg Kroah-Hartman]

From: John Hubbard <jhubbard@nvidia.com>

[ Upstream commit 57343d51613227373759f5b0f2eede257fd4b82e ]

This fixes the case of get_user_pages_fast() returning a -errno.
The result needs to be stored in a signed integer. And for safe
signed/unsigned comparisons, it's best to keep everything signed.
And get_user_pages_fast() also expects a signed value for number
of pages to pin.

Therefore, change most relevant variables, from u32 to int. Leave
"n" unsigned, for convenience in checking for overflow. And provide
a WARN_ON_ONCE() and early return, if overflow occurs.

Also, as long as we're tidying up: rename the page array from page,
to pages, in order to match the conventions used in most other call
sites.

Fixes: 20ec628e8007e ("misc: xilinx_sdfec: Add ability to configure LDPC")
Cc: Derek Kiernan <derek.kiernan@xilinx.com>
Cc: Dragan Cvetic <dragan.cvetic@xilinx.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Link: https://lore.kernel.org/r/20200527012628.1100649-2-jhubbard@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/misc/xilinx_sdfec.c | 27 +++++++++++++++++----------
 1 file changed, 17 insertions(+), 10 deletions(-)

diff --git a/drivers/misc/xilinx_sdfec.c b/drivers/misc/xilinx_sdfec.c
index 48ba7e02bed72..d4c14b617201e 100644
--- a/drivers/misc/xilinx_sdfec.c
+++ b/drivers/misc/xilinx_sdfec.c
@@ -602,10 +602,10 @@ static int xsdfec_table_write(struct xsdfec_dev *xsdfec, u32 offset,
 			      const u32 depth)
 {
 	u32 reg = 0;
-	u32 res;
-	u32 n, i;
+	int res, i, nr_pages;
+	u32 n;
 	u32 *addr = NULL;
-	struct page *page[MAX_NUM_PAGES];
+	struct page *pages[MAX_NUM_PAGES];
 
 	/*
 	 * Writes that go beyond the length of
@@ -622,15 +622,22 @@ static int xsdfec_table_write(struct xsdfec_dev *xsdfec, u32 offset,
 	if ((len * XSDFEC_REG_WIDTH_JUMP) % PAGE_SIZE)
 		n += 1;
 
-	res = get_user_pages_fast((unsigned long)src_ptr, n, 0, page);
-	if (res < n) {
-		for (i = 0; i < res; i++)
-			put_page(page[i]);
+	if (WARN_ON_ONCE(n > INT_MAX))
+		return -EINVAL;
+
+	nr_pages = n;
+
+	res = get_user_pages_fast((unsigned long)src_ptr, nr_pages, 0, pages);
+	if (res < nr_pages) {
+		if (res > 0) {
+			for (i = 0; i < res; i++)
+				put_page(pages[i]);
+		}
 		return -EINVAL;
 	}
 
-	for (i = 0; i < n; i++) {
-		addr = kmap(page[i]);
+	for (i = 0; i < nr_pages; i++) {
+		addr = kmap(pages[i]);
 		do {
 			xsdfec_regwrite(xsdfec,
 					base_addr + ((offset + reg) *
@@ -639,7 +646,7 @@ static int xsdfec_table_write(struct xsdfec_dev *xsdfec, u32 offset,
 			reg++;
 		} while ((reg < len) &&
 			 ((reg * XSDFEC_REG_WIDTH_JUMP) % PAGE_SIZE));
-		put_page(page[i]);
+		put_page(pages[i]);
 	}
 	return reg;
 }
-- 
2.25.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.4 260/314] usb/xhci-plat: Set PM runtime as active on resume

[Greg Kroah-Hartman]

From: Qais Yousef <qais.yousef@arm.com>

[ Upstream commit 79112cc3c29f4a8c73a21428fbcbcb0afb005e3e ]

Follow suit of ohci-platform.c and perform pm_runtime_set_active() on
resume.

ohci-platform.c had a warning reported due to the missing
pm_runtime_set_active() [1].

[1] https://lore.kernel.org/lkml/20200323143857.db5zphxhq4hz3hmd@e107158-lin.cambridge.arm.com/

Signed-off-by: Qais Yousef <qais.yousef@arm.com>
CC: Tony Prisk <linux@prisktech.co.nz>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: Oliver Neukum <oneukum@suse.de>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20200518154931.6144-2-qais.yousef@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/host/xhci-plat.c | 10 +++++++++-
 1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/usb/host/xhci-plat.c b/drivers/usb/host/xhci-plat.c
index 52c625c023410..60d06e9b600f8 100644
--- a/drivers/usb/host/xhci-plat.c
+++ b/drivers/usb/host/xhci-plat.c
@@ -410,7 +410,15 @@ static int __maybe_unused xhci_plat_resume(struct device *dev)
 	if (ret)
 		return ret;
 
-	return xhci_resume(xhci, 0);
+	ret = xhci_resume(xhci, 0);
+	if (ret)
+		return ret;
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
 }
 
 static int __maybe_unused xhci_plat_runtime_suspend(struct device *dev)
-- 
2.25.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.4 262/314] usb/ehci-platform: Set PM runtime as active on resume

[Greg Kroah-Hartman]

From: Qais Yousef <qais.yousef@arm.com>

[ Upstream commit 16bdc04cc98ab0c74392ceef2475ecc5e73fcf49 ]

Follow suit of ohci-platform.c and perform pm_runtime_set_active() on
resume.

ohci-platform.c had a warning reported due to the missing
pm_runtime_set_active() [1].

[1] https://lore.kernel.org/lkml/20200323143857.db5zphxhq4hz3hmd@e107158-lin.cambridge.arm.com/

Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Qais Yousef <qais.yousef@arm.com>
CC: Tony Prisk <linux@prisktech.co.nz>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Mathias Nyman <mathias.nyman@intel.com>
CC: Oliver Neukum <oneukum@suse.de>
CC: linux-arm-kernel@lists.infradead.org
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/r/20200518154931.6144-3-qais.yousef@arm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/host/ehci-platform.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/usb/host/ehci-platform.c b/drivers/usb/host/ehci-platform.c
index e4fc3f66d43bf..e9a49007cce4a 100644
--- a/drivers/usb/host/ehci-platform.c
+++ b/drivers/usb/host/ehci-platform.c
@@ -455,6 +455,10 @@ static int ehci_platform_resume(struct device *dev)
 
 	ehci_resume(hcd, priv->reset_on_resume);
 
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
 	if (priv->quirk_poll)
 		quirk_poll_init(priv);
 
-- 
2.25.1




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel