From: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
To: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Cc: linux-actions@lists.infradead.org, linux-kernel@vger.kernel.org,
"Peter Rosin" <peda@axentia.se>, "Wolfram Sang" <wsa@kernel.org>,
linux-i2c@vger.kernel.org, "Andreas Färber" <afaerber@suse.de>,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH 2/3] i2c: owl: Add support for atomic transfers
Date: Sun, 11 Oct 2020 19:39:20 +0530 [thread overview]
Message-ID: <20201011140920.GB4971@Mani-XPS-13-9360> (raw)
In-Reply-To: <1af37112fafd6cf069dfe864560f77996f57d80d.1602190168.git.cristian.ciocaltea@gmail.com>
On Fri, Oct 09, 2020 at 12:44:40AM +0300, Cristian Ciocaltea wrote:
> Atomic transfers are required to properly power off a machine through
> an I2C controlled PMIC, such as the Actions Semi ATC260x series.
>
> System shutdown may happen with interrupts being disabled and, as a
> consequence, the kernel may hang if the driver does not support atomic
> transfers.
>
> This functionality is essentially implemented by polling the FIFO
> Status register until either Command Execute Completed or NACK Error
> bits are set.
>
> Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Thanks,
Mani
> ---
> drivers/i2c/busses/i2c-owl.c | 76 ++++++++++++++++++++++++++----------
> 1 file changed, 56 insertions(+), 20 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-owl.c b/drivers/i2c/busses/i2c-owl.c
> index a163b8f308c1..547132768119 100644
> --- a/drivers/i2c/busses/i2c-owl.c
> +++ b/drivers/i2c/busses/i2c-owl.c
> @@ -14,6 +14,7 @@
> #include <linux/i2c.h>
> #include <linux/interrupt.h>
> #include <linux/io.h>
> +#include <linux/iopoll.h>
> #include <linux/module.h>
> #include <linux/of_device.h>
>
> @@ -76,6 +77,7 @@
> #define OWL_I2C_FIFOCTL_TFR BIT(2)
>
> /* I2Cc_FIFOSTAT Bit Mask */
> +#define OWL_I2C_FIFOSTAT_CECB BIT(0)
> #define OWL_I2C_FIFOSTAT_RNB BIT(1)
> #define OWL_I2C_FIFOSTAT_RFE BIT(2)
> #define OWL_I2C_FIFOSTAT_TFF BIT(5)
> @@ -83,7 +85,8 @@
> #define OWL_I2C_FIFOSTAT_RFD GENMASK(15, 8)
>
> /* I2C bus timeout */
> -#define OWL_I2C_TIMEOUT msecs_to_jiffies(4 * 1000)
> +#define OWL_I2C_TIMEOUT_MS (4 * 1000)
> +#define OWL_I2C_TIMEOUT msecs_to_jiffies(OWL_I2C_TIMEOUT_MS)
>
> #define OWL_I2C_MAX_RETRIES 50
>
> @@ -161,15 +164,11 @@ static void owl_i2c_set_freq(struct owl_i2c_dev *i2c_dev)
> writel(OWL_I2C_DIV_FACTOR(val), i2c_dev->base + OWL_I2C_REG_CLKDIV);
> }
>
> -static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> +static void owl_i2c_xfer_data(struct owl_i2c_dev *i2c_dev)
> {
> - struct owl_i2c_dev *i2c_dev = _dev;
> struct i2c_msg *msg = i2c_dev->msg;
> - unsigned long flags;
> unsigned int stat, fifostat;
>
> - spin_lock_irqsave(&i2c_dev->lock, flags);
> -
> i2c_dev->err = 0;
>
> /* Handle NACK from slave */
> @@ -179,7 +178,7 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> /* Clear NACK error bit by writing "1" */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOSTAT,
> OWL_I2C_FIFOSTAT_RNB, true);
> - goto stop;
> + return;
> }
>
> /* Handle bus error */
> @@ -189,7 +188,7 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> /* Clear BUS error bit by writing "1" */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT,
> OWL_I2C_STAT_BEB, true);
> - goto stop;
> + return;
> }
>
> /* Handle FIFO read */
> @@ -207,13 +206,23 @@ static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> i2c_dev->base + OWL_I2C_REG_TXDAT);
> }
> }
> +}
> +
> +static irqreturn_t owl_i2c_interrupt(int irq, void *_dev)
> +{
> + struct owl_i2c_dev *i2c_dev = _dev;
> + unsigned long flags;
> +
> + spin_lock_irqsave(&i2c_dev->lock, flags);
> +
> + owl_i2c_xfer_data(i2c_dev);
>
> -stop:
> /* Clear pending interrupts */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT,
> OWL_I2C_STAT_IRQP, true);
>
> complete_all(&i2c_dev->msg_complete);
> +
> spin_unlock_irqrestore(&i2c_dev->lock, flags);
>
> return IRQ_HANDLED;
> @@ -241,8 +250,8 @@ static int owl_i2c_check_bus_busy(struct i2c_adapter *adap)
> return 0;
> }
>
> -static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> - int num)
> +static int owl_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg *msgs,
> + int num, bool atomic)
> {
> struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap);
> struct i2c_msg *msg;
> @@ -286,11 +295,12 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> goto err_exit;
> }
>
> - reinit_completion(&i2c_dev->msg_complete);
> + if (!atomic)
> + reinit_completion(&i2c_dev->msg_complete);
>
> - /* Enable I2C controller interrupt */
> + /* Enable/disable I2C controller interrupt */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
> - OWL_I2C_CTL_IRQE, true);
> + OWL_I2C_CTL_IRQE, !atomic);
>
> /*
> * Select: FIFO enable, Master mode, Stop enable, Data count enable,
> @@ -358,20 +368,33 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
>
> spin_unlock_irqrestore(&i2c_dev->lock, flags);
>
> - time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
> - adap->timeout);
> + if (atomic) {
> + /* Wait for Command Execute Completed or NACK Error bits */
> + ret = readl_poll_timeout_atomic(i2c_dev->base + OWL_I2C_REG_FIFOSTAT,
> + val, val & (OWL_I2C_FIFOSTAT_CECB |
> + OWL_I2C_FIFOSTAT_RNB),
> + 10, OWL_I2C_TIMEOUT_MS * 1000);
> + } else {
> + time_left = wait_for_completion_timeout(&i2c_dev->msg_complete,
> + adap->timeout);
> + if (!time_left)
> + ret = -ETIMEDOUT;
> + }
>
> spin_lock_irqsave(&i2c_dev->lock, flags);
> - if (time_left == 0) {
> +
> + if (ret) {
> dev_err(&adap->dev, "Transaction timed out\n");
> /* Send stop condition and release the bus */
> owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL,
> OWL_I2C_CTL_GBCC_STOP | OWL_I2C_CTL_RB,
> true);
> - ret = -ETIMEDOUT;
> goto err_exit;
> }
>
> + if (atomic)
> + owl_i2c_xfer_data(i2c_dev);
> +
> ret = i2c_dev->err < 0 ? i2c_dev->err : num;
>
> err_exit:
> @@ -385,9 +408,22 @@ static int owl_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> return ret;
> }
>
> +static int owl_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
> + int num)
> +{
> + return owl_i2c_xfer_common(adap, msgs, num, false);
> +}
> +
> +static int owl_i2c_xfer_atomic(struct i2c_adapter *adap,
> + struct i2c_msg *msgs, int num)
> +{
> + return owl_i2c_xfer_common(adap, msgs, num, true);
> +}
> +
> static const struct i2c_algorithm owl_i2c_algorithm = {
> - .master_xfer = owl_i2c_master_xfer,
> - .functionality = owl_i2c_func,
> + .master_xfer = owl_i2c_xfer,
> + .master_xfer_atomic = owl_i2c_xfer_atomic,
> + .functionality = owl_i2c_func,
> };
>
> static const struct i2c_adapter_quirks owl_i2c_quirks = {
> --
> 2.28.0
>
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2020-10-11 14:10 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-10-08 21:44 [PATCH 0/3] Improve Actions Semi Owl I2C driver Cristian Ciocaltea
2020-10-08 21:44 ` [PATCH 1/3] i2c: owl: Clear NACK and BUS error bits Cristian Ciocaltea
2020-10-10 11:16 ` Wolfram Sang
2020-10-11 14:09 ` Manivannan Sadhasivam
2020-10-12 9:05 ` Cristian Ciocaltea
2020-10-08 21:44 ` [PATCH 2/3] i2c: owl: Add support for atomic transfers Cristian Ciocaltea
2020-10-11 14:09 ` Manivannan Sadhasivam [this message]
2020-10-12 9:07 ` Cristian Ciocaltea
2020-11-03 20:57 ` Wolfram Sang
2020-10-08 21:44 ` [PATCH 3/3] i2c: owl: Enable asynchronous probing Cristian Ciocaltea
2020-10-11 14:06 ` Manivannan Sadhasivam
2020-10-12 9:08 ` Cristian Ciocaltea
2020-11-03 20:57 ` Wolfram Sang
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201011140920.GB4971@Mani-XPS-13-9360 \
--to=manivannan.sadhasivam@linaro.org \
--cc=afaerber@suse.de \
--cc=cristian.ciocaltea@gmail.com \
--cc=linux-actions@lists.infradead.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-i2c@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=peda@axentia.se \
--cc=wsa@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox