From: Krzysztof Kozlowski <krzk@kernel.org>
To: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
Rob Herring <robh+dt@kernel.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
linux-arm-kernel@lists.infradead.org,
linux-media@vger.kernel.org
Subject: Re: [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor
Date: Wed, 27 Jan 2021 13:51:34 +0100 [thread overview]
Message-ID: <20210127125134.aayb2xb4lcl4ekn5@kozik-lap> (raw)
In-Reply-To: <20210127124553.GB32460@paasikivi.fi.intel.com>
On Wed, Jan 27, 2021 at 02:45:53PM +0200, Sakari Ailus wrote:
> On Wed, Jan 27, 2021 at 01:26:12PM +0100, Krzysztof Kozlowski wrote:
> > On Fri, Jan 22, 2021 at 11:18:22AM +0200, Sakari Ailus wrote:
> > > Hi Krysztof,
> > >
> > > On Wed, Nov 18, 2020 at 09:27:12PM +0100, Krzysztof Kozlowski wrote:
> > > > Add bindings for the IMX258 camera sensor. The bindings, just like the
> > > > driver, are quite limited, e.g. do not support regulator supplies.
> > > >
> > > > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> > > > Reviewed-by: Rob Herring <robh@kernel.org>
> > > >
> > > > ---
> > > >
> > > > Changes since v4:
> > > > 1. Add clock-lanes,
> > > > 2. Add Rob's review,
> > > > 3. Add one more example and extend existing one,
> > > > 4. Add common clock properties (assigned-*).
> > > >
> > > > Changes since v3:
> > > > 1. Document also two lane setup.
> > > >
> > > > Changes since v2:
> > > > 1. Remove clock-frequency, add reset GPIOs, add supplies.
> > > > 2. Use additionalProperties.
> > > >
> > > > Changes since v1:
> > > > 1. None
> > > > ---
> > > > .../devicetree/bindings/media/i2c/imx258.yaml | 140 ++++++++++++++++++
> > > > MAINTAINERS | 1 +
> > > > 2 files changed, 141 insertions(+)
> > > > create mode 100644 Documentation/devicetree/bindings/media/i2c/imx258.yaml
> > > >
> > > > diff --git a/Documentation/devicetree/bindings/media/i2c/imx258.yaml b/Documentation/devicetree/bindings/media/i2c/imx258.yaml
> > > > new file mode 100644
> > > > index 000000000000..4a3471fb88a1
> > > > --- /dev/null
> > > > +++ b/Documentation/devicetree/bindings/media/i2c/imx258.yaml
> > > > @@ -0,0 +1,140 @@
> > > > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > > > +%YAML 1.2
> > > > +---
> > > > +$id: http://devicetree.org/schemas/media/i2c/imx258.yaml#
> > > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > > +
> > > > +title: Sony IMX258 13 Mpixel CMOS Digital Image Sensor
> > > > +
> > > > +maintainers:
> > > > + - Krzysztof Kozlowski <krzk@kernel.org>
> > > > +
> > > > +description: |-
> > > > + IMX258 is a diagonal 5.867mm (Type 1/3.06) 13 Mega-pixel CMOS active pixel
> > > > + type stacked image sensor with a square pixel array of size 4208 x 3120. It
> > > > + is programmable through I2C interface. Image data is sent through MIPI
> > > > + CSI-2.
> > > > +
> > > > +properties:
> > > > + compatible:
> > > > + const: sony,imx258
> > > > +
> > > > + assigned-clocks: true
> > > > + assigned-clock-parents: true
> > > > + assigned-clock-rates: true
> > > > +
> > > > + clocks:
> > > > + description:
> > > > + Clock frequency from 6 to 27 MHz.
> > > > + maxItems: 1
> > > > +
> > > > + reg:
> > > > + maxItems: 1
> > > > +
> > > > + reset-gpios:
> > > > + description: |-
> > > > + Reference to the GPIO connected to the XCLR pin, if any.
> > > > +
> > > > + vana-supply:
> > > > + description:
> > > > + Analog voltage (VANA) supply, 2.7 V
> > > > +
> > > > + vdig-supply:
> > > > + description:
> > > > + Digital I/O voltage (VDIG) supply, 1.2 V
> > > > +
> > > > + vif-supply:
> > > > + description:
> > > > + Interface voltage (VIF) supply, 1.8 V
> > > > +
> > > > + # See ../video-interfaces.txt for more details
> > > > + port:
> > > > + type: object
> > > > + properties:
> > > > + endpoint:
> > > > + type: object
> > > > + properties:
> > > > + clock-lanes:
> > > > + const: 0
> > >
> > > This is redundant. Please remove, same for the examples. Can be a separate
> > > patch, too.
> >
> > Before I remove too much - you mean "clock-lanes" is redundant or entire
> > set of properties in "port" node?
>
> Just clock-lanes. The rest are just as they should be IMO.
Yes, makes sense. Thanks for confirmation.
Best regards,
Krzysztof
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
prev parent reply other threads:[~2021-01-27 12:53 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-18 20:27 [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor Krzysztof Kozlowski
2020-11-18 20:27 ` [PATCH v6 2/4] media: i2c: imx258: add support for binding via device tree Krzysztof Kozlowski
2020-11-18 20:27 ` [PATCH v6 3/4] media: i2c: imx258: simplify getting state container Krzysztof Kozlowski
2020-11-18 20:27 ` [PATCH v6 4/4] media: i2c: imx258: get clock from device properties and enable it via runtime PM Krzysztof Kozlowski
2021-01-22 9:18 ` [PATCH v6 1/4] dt-bindings: media: imx258: add bindings for IMX258 sensor Sakari Ailus
2021-01-27 12:23 ` Krzysztof Kozlowski
2021-01-27 12:26 ` Krzysztof Kozlowski
2021-01-27 12:45 ` Sakari Ailus
2021-01-27 12:51 ` Krzysztof Kozlowski [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20210127125134.aayb2xb4lcl4ekn5@kozik-lap \
--to=krzk@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=robh+dt@kernel.org \
--cc=sakari.ailus@linux.intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox