[PATCH AUTOSEL 5.10 09/85] net: stmmac: Set FIFO sizes for ipq806x

[PATCH AUTOSEL 5.10 09/85] net: stmmac: Set FIFO sizes for ipq806x

[Sasha Levin]

From: Jonathan McDowell <noodles@earth.li>

[ Upstream commit e127906b68b49ddb3ecba39ffa36a329c48197d3 ]

Commit eaf4fac47807 ("net: stmmac: Do not accept invalid MTU values")
started using the TX FIFO size to verify what counts as a valid MTU
request for the stmmac driver.  This is unset for the ipq806x variant.
Looking at older patches for this it seems the RX + TXs buffers can be
up to 8k, so set appropriately.

(I sent this as an RFC patch in June last year, but received no replies.
I've been running with this on my hardware (a MikroTik RB3011) since
then with larger MTUs to support both the internal qca8k switch and
VLANs with no problems. Without the patch it's impossible to set the
larger MTU required to support this.)

Signed-off-by: Jonathan McDowell <noodles@earth.li>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
index bf3250e0e59c..749585fe6fc9 100644
--- a/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
+++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-ipq806x.c
@@ -352,6 +352,8 @@ static int ipq806x_gmac_probe(struct platform_device *pdev)
 	plat_dat->bsp_priv = gmac;
 	plat_dat->fix_mac_speed = ipq806x_gmac_fix_mac_speed;
 	plat_dat->multicast_filter_bins = 0;
+	plat_dat->tx_fifo_size = 8192;
+	plat_dat->rx_fifo_size = 8192;
 
 	err = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res);
 	if (err)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 32/85] Bluetooth: btusb: Enable quirk boolean flag for Mediatek Chip.

[Sasha Levin]

From: "mark-yw.chen" <mark-yw.chen@mediatek.com>

[ Upstream commit 27e554a4fcd84e499bf0a82122b8c4c3f1de38b6 ]

Adding support LE scatternet and WBS for Mediatek Chip

Signed-off-by: mark-yw.chen <mark-yw.chen@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/bluetooth/btusb.c | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
index 2953b96b3ced..175cb1c0d569 100644
--- a/drivers/bluetooth/btusb.c
+++ b/drivers/bluetooth/btusb.c
@@ -392,7 +392,9 @@ static const struct usb_device_id blacklist_table[] = {
 
 	/* MediaTek Bluetooth devices */
 	{ USB_VENDOR_AND_INTERFACE_INFO(0x0e8d, 0xe0, 0x01, 0x01),
-	  .driver_info = BTUSB_MEDIATEK },
+	  .driver_info = BTUSB_MEDIATEK |
+			 BTUSB_WIDEBAND_SPEECH |
+			 BTUSB_VALID_LE_STATES },
 
 	/* Additional Realtek 8723AE Bluetooth devices */
 	{ USB_DEVICE(0x0930, 0x021d), .driver_info = BTUSB_REALTEK },
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 36/85] coresight: Do not scan for graph if none is present

[Sasha Levin]

From: Suzuki K Poulose <suzuki.poulose@arm.com>

[ Upstream commit 2b921b671a8d29c2adb255a86409aad1e3267309 ]

If a graph node is not found for a given node, of_get_next_endpoint()
will emit the following error message :

 OF: graph: no port node found in /<node_name>

If the given component doesn't have any explicit connections (e.g,
ETE) we could simply ignore the graph parsing. As for any legacy
component where this is mandatory, the device will not be usable
as before this patch. Updating the DT bindings to Yaml and enabling
the schema checks can detect such issues with the DT.

Cc: Mike Leach <mike.leach@linaro.org>
Cc: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20210405164307.1720226-11-suzuki.poulose@arm.com
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/hwtracing/coresight/coresight-platform.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/drivers/hwtracing/coresight/coresight-platform.c b/drivers/hwtracing/coresight/coresight-platform.c
index 3629b7885aca..c594f45319fc 100644
--- a/drivers/hwtracing/coresight/coresight-platform.c
+++ b/drivers/hwtracing/coresight/coresight-platform.c
@@ -90,6 +90,12 @@ static void of_coresight_get_ports_legacy(const struct device_node *node,
 	struct of_endpoint endpoint;
 	int in = 0, out = 0;
 
+	/*
+	 * Avoid warnings in of_graph_get_next_endpoint()
+	 * if the device doesn't have any graph connections
+	 */
+	if (!of_graph_is_present(node))
+		return;
 	do {
 		ep = of_graph_get_next_endpoint(node, ep);
 		if (!ep)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 39/85] pinctrl: samsung: use 'int' for register masks in Exynos

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

[ Upstream commit fa0c10a5f3a49130dd11281aa27e7e1c8654abc7 ]

The Special Function Registers on all Exynos SoC, including ARM64, are
32-bit wide, so entire driver uses matching functions like readl() or
writel().  On 64-bit ARM using unsigned long for register masks:
1. makes little sense as immediately after bitwise operation it will be
   cast to 32-bit value when calling writel(),
2. is actually error-prone because it might promote other operands to
   64-bit.

Addresses-Coverity: Unintentional integer overflow
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20210408195029.69974-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pinctrl/samsung/pinctrl-exynos.c | 10 +++++-----
 1 file changed, 5 insertions(+), 5 deletions(-)

diff --git a/drivers/pinctrl/samsung/pinctrl-exynos.c b/drivers/pinctrl/samsung/pinctrl-exynos.c
index b9ea09fabf84..493079a47d05 100644
--- a/drivers/pinctrl/samsung/pinctrl-exynos.c
+++ b/drivers/pinctrl/samsung/pinctrl-exynos.c
@@ -55,7 +55,7 @@ static void exynos_irq_mask(struct irq_data *irqd)
 	struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
 	struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
 	unsigned long reg_mask = our_chip->eint_mask + bank->eint_offset;
-	unsigned long mask;
+	unsigned int mask;
 	unsigned long flags;
 
 	spin_lock_irqsave(&bank->slock, flags);
@@ -83,7 +83,7 @@ static void exynos_irq_unmask(struct irq_data *irqd)
 	struct exynos_irq_chip *our_chip = to_exynos_irq_chip(chip);
 	struct samsung_pin_bank *bank = irq_data_get_irq_chip_data(irqd);
 	unsigned long reg_mask = our_chip->eint_mask + bank->eint_offset;
-	unsigned long mask;
+	unsigned int mask;
 	unsigned long flags;
 
 	/*
@@ -483,7 +483,7 @@ static void exynos_irq_eint0_15(struct irq_desc *desc)
 	chained_irq_exit(chip, desc);
 }
 
-static inline void exynos_irq_demux_eint(unsigned long pend,
+static inline void exynos_irq_demux_eint(unsigned int pend,
 						struct irq_domain *domain)
 {
 	unsigned int irq;
@@ -500,8 +500,8 @@ static void exynos_irq_demux_eint16_31(struct irq_desc *desc)
 {
 	struct irq_chip *chip = irq_desc_get_chip(desc);
 	struct exynos_muxed_weint_data *eintd = irq_desc_get_handler_data(desc);
-	unsigned long pend;
-	unsigned long mask;
+	unsigned int pend;
+	unsigned int mask;
 	int i;
 
 	chained_irq_enter(chip, desc);
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 41/85] mt76: mt7615: support loading EEPROM for MT7613BE

[Sasha Levin]

From: Sander Vanheule <sander@svanheule.net>

[ Upstream commit 858ebf446bee7d5077bd99488aae617908c3f4fe ]

EEPROM blobs for MT7613BE radios start with (little endian) 0x7663,
which is also the PCI device ID for this device. The EEPROM is required
for the radio to work at useful power levels, otherwise only the lowest
power level is available.

Suggested-by: Georgi Vlaev <georgi.vlaev@konsulko.com>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c b/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
index f4756bb946c3..e9cdcdc54d5c 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/eeprom.c
@@ -86,6 +86,7 @@ static int mt7615_check_eeprom(struct mt76_dev *dev)
 	switch (val) {
 	case 0x7615:
 	case 0x7622:
+	case 0x7663:
 		return 0;
 	default:
 		return -EINVAL;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 42/85] mt76: mt76x0: disable GTK offloading

[Sasha Levin]

From: David Bauer <mail@david-bauer.net>

[ Upstream commit 4b36cc6b390f18dbc59a45fb4141f90d7dfe2b23 ]

When operating two VAP on a MT7610 with encryption (PSK2, SAE, OWE),
only the first one to be created will transmit properly encrypteded
frames.

All subsequently created VAPs will sent out frames with the payload left
unencrypted, breaking multicast traffic (ICMP6 NDP) and potentially
disclosing information to a third party.

Disable GTK offloading and encrypt these frames in software to
circumvent this issue. THis only seems to be necessary on MT7610 chips,
as MT7612 is not affected from our testing.

Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt76x02_util.c | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/drivers/net/wireless/mediatek/mt76/mt76x02_util.c b/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
index 11b769af2f8f..0f191bd28417 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x02_util.c
@@ -446,6 +446,10 @@ int mt76x02_set_key(struct ieee80211_hw *hw, enum set_key_cmd cmd,
 	    !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
 		return -EOPNOTSUPP;
 
+	/* MT76x0 GTK offloading does not work with more than one VIF */
+	if (is_mt76x0(dev) && !(key->flags & IEEE80211_KEY_FLAG_PAIRWISE))
+		return -EOPNOTSUPP;
+
 	msta = sta ? (struct mt76x02_sta *)sta->drv_priv : NULL;
 	wcid = msta ? &msta->wcid : &mvif->group_wcid;
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 43/85] mt76: mt7915: fix txpower init for TSSI off chips

[Sasha Levin]

From: Shayne Chen <shayne.chen@mediatek.com>

[ Upstream commit a226ccd04c479ccd23d6927c64bad1b441707f70 ]

Fix incorrect txpower init value for TSSI off chips which causes
too small txpower.

Signed-off-by: Shayne Chen <shayne.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../wireless/mediatek/mt76/mt7915/eeprom.c    | 19 +++++++++++++------
 1 file changed, 13 insertions(+), 6 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c b/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c
index 7deba7ebd68a..e4c5f968f706 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7915/eeprom.c
@@ -104,7 +104,7 @@ int mt7915_eeprom_get_target_power(struct mt7915_dev *dev,
 				   struct ieee80211_channel *chan,
 				   u8 chain_idx)
 {
-	int index;
+	int index, target_power;
 	bool tssi_on;
 
 	if (chain_idx > 3)
@@ -113,15 +113,22 @@ int mt7915_eeprom_get_target_power(struct mt7915_dev *dev,
 	tssi_on = mt7915_tssi_enabled(dev, chan->band);
 
 	if (chan->band == NL80211_BAND_2GHZ) {
-		index = MT_EE_TX0_POWER_2G + chain_idx * 3 + !tssi_on;
+		index = MT_EE_TX0_POWER_2G + chain_idx * 3;
+		target_power = mt7915_eeprom_read(dev, index);
+
+		if (!tssi_on)
+			target_power += mt7915_eeprom_read(dev, index + 1);
 	} else {
-		int group = tssi_on ?
-			    mt7915_get_channel_group(chan->hw_value) : 8;
+		int group = mt7915_get_channel_group(chan->hw_value);
+
+		index = MT_EE_TX0_POWER_5G + chain_idx * 12;
+		target_power = mt7915_eeprom_read(dev, index + group);
 
-		index = MT_EE_TX0_POWER_5G + chain_idx * 12 + group;
+		if (!tssi_on)
+			target_power += mt7915_eeprom_read(dev, index + 8);
 	}
 
-	return mt7915_eeprom_read(dev, index);
+	return target_power;
 }
 
 static const u8 sku_cck_delta_map[] = {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 69/85] mt76: mt7615: fix entering driver-own state on mt7663

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 5c7d374444afdeb9dd534a37c4f6c13af032da0c ]

Fixes hardware wakeup issues

Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/wireless/mediatek/mt76/mt7615/mcu.c | 12 ++++++++++--
 1 file changed, 10 insertions(+), 2 deletions(-)

diff --git a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
index c31036f57aef..62a971660da7 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7615/mcu.c
@@ -341,12 +341,20 @@ static int mt7615_mcu_drv_pmctrl(struct mt7615_dev *dev)
 	u32 addr;
 	int err;
 
-	addr = is_mt7663(mdev) ? MT_PCIE_DOORBELL_PUSH : MT_CFG_LPCR_HOST;
+	if (is_mt7663(mdev)) {
+		/* Clear firmware own via N9 eint */
+		mt76_wr(dev, MT_PCIE_DOORBELL_PUSH, MT_CFG_LPCR_HOST_DRV_OWN);
+		mt76_poll(dev, MT_CONN_ON_MISC, MT_CFG_LPCR_HOST_FW_OWN, 0, 3000);
+
+		addr = MT_CONN_HIF_ON_LPCTL;
+	} else {
+		addr = MT_CFG_LPCR_HOST;
+	}
+
 	mt76_wr(dev, addr, MT_CFG_LPCR_HOST_DRV_OWN);
 
 	mt7622_trigger_hif_int(dev, true);
 
-	addr = is_mt7663(mdev) ? MT_CONN_HIF_ON_LPCTL : MT_CFG_LPCR_HOST;
 	err = !mt76_poll_msec(dev, addr, MT_CFG_LPCR_HOST_FW_OWN, 0, 3000);
 
 	mt7622_trigger_hif_int(dev, false);
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 76/85] net: ethernet: mtk_eth_soc: fix RX VLAN offload

[Sasha Levin]

From: Felix Fietkau <nbd@nbd.name>

[ Upstream commit 3f57d8c40fea9b20543cab4da12f4680d2ef182c ]

The VLAN ID in the rx descriptor is only valid if the RX_DMA_VTAG bit is
set. Fixes frames wrongly marked with VLAN tags.

Signed-off-by: Felix Fietkau <nbd@nbd.name>
[Ilya: fix commit message]
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 2 +-
 drivers/net/ethernet/mediatek/mtk_eth_soc.h | 1 +
 2 files changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index 6d2d60675ffd..d930fcda9c3b 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -1319,7 +1319,7 @@ static int mtk_poll_rx(struct napi_struct *napi, int budget,
 		skb->protocol = eth_type_trans(skb, netdev);
 
 		if (netdev->features & NETIF_F_HW_VLAN_CTAG_RX &&
-		    RX_DMA_VID(trxd.rxd3))
+		    (trxd.rxd2 & RX_DMA_VTAG))
 			__vlan_hwaccel_put_tag(skb, htons(ETH_P_8021Q),
 					       RX_DMA_VID(trxd.rxd3));
 		skb_record_rx_queue(skb, 0);
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
index 454cfcd465fd..73ce1f0f307a 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -295,6 +295,7 @@
 #define RX_DMA_LSO		BIT(30)
 #define RX_DMA_PLEN0(_x)	(((_x) & 0x3fff) << 16)
 #define RX_DMA_GET_PLEN0(_x)	(((_x) >> 16) & 0x3fff)
+#define RX_DMA_VTAG		BIT(15)
 
 /* QDMA descriptor rxd3 */
 #define RX_DMA_VID(_x)		((_x) & 0xfff)
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel