[PATCH AUTOSEL 5.13 003/108] ARM: dts: rockchip: Fix thermal sensor cells o rk322x

[PATCH AUTOSEL 5.13 003/108] ARM: dts: rockchip: Fix thermal sensor cells o rk322x

[Sasha Levin]

From: Ezequiel Garcia <ezequiel@collabora.com>

[ Upstream commit d5c24e20daf09587cbc221d40be1ba92673e8d94 ]

The number of cells to be used with a thermal sensor specifier
must be "1". Fix this.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210506175514.168365-2-ezequiel@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk322x.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi
index 208f21245095..9f02ba7a0cc2 100644
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rk322x.dtsi
@@ -517,7 +517,7 @@ tsadc: tsadc@11150000 {
 		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
 		pinctrl-2 = <&otp_pin>;
-		#thermal-sensor-cells = <0>;
+		#thermal-sensor-cells = <1>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
 	};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 004/108] ARM: dts: rockchip: fix pinctrl sleep nodename for rk3036-kylin and rk3288

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit dfbfb86a43f9a5bbd166d88bca9e07ee4e1bff31 ]

A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.

Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288

make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3036-kylin.dts | 2 +-
 arch/arm/boot/dts/rk3288.dtsi      | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/rk3036-kylin.dts b/arch/arm/boot/dts/rk3036-kylin.dts
index 7154b827ea2f..e817eba8c622 100644
--- a/arch/arm/boot/dts/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rk3036-kylin.dts
@@ -390,7 +390,7 @@ sdmmc_pwr: sdmmc-pwr {
 		};
 	};
 
-	sleep {
+	suspend {
 		global_pwroff: global-pwroff {
 			rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
 		};
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 05557ad02b33..24b903240cb3 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -1582,7 +1582,7 @@ pcfg_pull_none_12ma: pcfg-pull-none-12ma {
 			drive-strength = <12>;
 		};
 
-		sleep {
+		suspend {
 			global_pwroff: global-pwroff {
 				rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 005/108] arm64: dts: rockchip: Use only supported PCIe link speed on rk3399

[Sasha Levin]

From: Peter Robinson <pbrobinson@gmail.com>

[ Upstream commit 954d5986afa50c178ea7554e6abdd611d08f5ade ]

The max link speed supported by the rk3399 is already set in the
rk3399.dtsi file so don't set unsupported link speeds in device
specific DTs. This is the same fix as 642fb27.

Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Link: https://lore.kernel.org/r/20210413141709.845592-1-pbrobinson@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi      | 1 -
 arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi    | 1 -
 arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi | 1 -
 3 files changed, 3 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
index 16fd58c4a80f..8c0ff6c96e03 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-nanopi4.dtsi
@@ -510,7 +510,6 @@ &pcie_phy {
 };
 
 &pcie0 {
-	max-link-speed = <2>;
 	num-lanes = <2>;
 	vpcie0v9-supply = <&vcca0v9_s3>;
 	vpcie1v8-supply = <&vcca1v8_s3>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
index 7d0a7c697703..b28888ea9262 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4.dtsi
@@ -474,7 +474,6 @@ &pcie_phy {
 
 &pcie0 {
 	ep-gpios = <&gpio4 RK_PD3 GPIO_ACTIVE_HIGH>;
-	max-link-speed = <2>;
 	num-lanes = <4>;
 	pinctrl-0 = <&pcie_clkreqnb_cpm>;
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi b/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
index c0074b3ed4af..01d1a75c8b4d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399pro-vmarc-som.dtsi
@@ -329,7 +329,6 @@ &pcie_phy {
 
 &pcie0 {
 	ep-gpios = <&gpio0 RK_PB4 GPIO_ACTIVE_HIGH>;
-	max-link-speed = <2>;
 	num-lanes = <4>;
 	pinctrl-0 = <&pcie_clkreqnb_cpm>;
 	pinctrl-names = "default";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 006/108] arm64: dts: rockchip: fix pinctrl sleep nodename for rk3399.dtsi

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit a7ecfad495f8af63a5cb332c91f60ab2018897f5 ]

A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.

Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 634a91af8e83..7c1b69f3a4c1 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -2354,7 +2354,7 @@ sdmmc_wp: sdmmc-wp {
 			};
 		};
 
-		sleep {
+		suspend {
 			ap_pwroff: ap-pwroff {
 				rockchip,pins = <1 RK_PA5 1 &pcfg_pull_none>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 007/108] ARM: dts: rockchip: Fix the timer clocks order

[Sasha Levin]

From: Ezequiel Garcia <ezequiel@collabora.com>

[ Upstream commit 7b46d674ac000b101fdad92cf16cc11d90b72f86 ]

Fixed order is the device-tree convention.
The timer driver currently gets clocks by name,
so no changes are needed there.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210506111136.3941-3-ezequiel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3188.dtsi | 8 ++++----
 arch/arm/boot/dts/rk3288.dtsi | 4 ++--
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index 2298a8d840ba..2c08ae60e4a1 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -150,16 +150,16 @@ timer3: timer@2000e000 {
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x2000e000 0x20>;
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER3>, <&cru PCLK_TIMER3>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER3>, <&cru SCLK_TIMER3>;
+		clock-names = "pclk", "timer";
 	};
 
 	timer6: timer@200380a0 {
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x200380a0 0x20>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER6>, <&cru PCLK_TIMER0>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER6>;
+		clock-names = "pclk", "timer";
 	};
 
 	i2s0: i2s@1011a000 {
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 24b903240cb3..1e6594f8a293 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -196,8 +196,8 @@ timer: timer@ff810000 {
 		compatible = "rockchip,rk3288-timer";
 		reg = <0x0 0xff810000 0x0 0x20>;
 		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};
 
 	display-subsystem {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 008/108] ARM: dts: rockchip: Fix IOMMU nodes properties on rk322x

[Sasha Levin]

From: Benjamin Gaignard <benjamin.gaignard@collabora.com>

[ Upstream commit 6b023929666f0be5df75f5e0278d1b70effadf42 ]

Add '#" to iommu-cells properties.
Remove useless interrupt-names properties

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Link: https://lore.kernel.org/r/20210507090232.233049-4-benjamin.gaignard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk322x.dtsi | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi
index 9f02ba7a0cc2..25f83f2f5618 100644
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rk322x.dtsi
@@ -558,10 +558,9 @@ vpu_mmu: iommu@20020800 {
 		compatible = "rockchip,iommu";
 		reg = <0x20020800 0x100>;
 		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
@@ -569,10 +568,9 @@ vdec_mmu: iommu@20030480 {
 		compatible = "rockchip,iommu";
 		reg = <0x20030480 0x40>, <0x200304c0 0x40>;
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vdec_mmu";
 		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
@@ -602,7 +600,6 @@ vop_mmu: iommu@20053f00 {
 		compatible = "rockchip,iommu";
 		reg = <0x20053f00 0x100>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -623,10 +620,9 @@ iep_mmu: iommu@20070800 {
 		compatible = "rockchip,iommu";
 		reg = <0x20070800 0x100>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 009/108] ARM: dts: rockchip: Fix power-controller node names for rk3066a

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit f2948781a72f0d8cf2adf31758c357f2f35e6c79 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3066a.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/rk3066a.dtsi b/arch/arm/boot/dts/rk3066a.dtsi
index 252750c97f97..bbc3bff50856 100644
--- a/arch/arm/boot/dts/rk3066a.dtsi
+++ b/arch/arm/boot/dts/rk3066a.dtsi
@@ -755,7 +755,7 @@ power: power-controller {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pd_vio@RK3066_PD_VIO {
+		power-domain@RK3066_PD_VIO {
 			reg = <RK3066_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -782,7 +782,7 @@ pd_vio@RK3066_PD_VIO {
 				 <&qos_rga>;
 		};
 
-		pd_video@RK3066_PD_VIDEO {
+		power-domain@RK3066_PD_VIDEO {
 			reg = <RK3066_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
@@ -791,7 +791,7 @@ pd_video@RK3066_PD_VIDEO {
 			pm_qos = <&qos_vpu>;
 		};
 
-		pd_gpu@RK3066_PD_GPU {
+		power-domain@RK3066_PD_GPU {
 			reg = <RK3066_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 010/108] ARM: dts: rockchip: Fix power-controller node names for rk3188

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit d3bcbcd396175ac26aa54919c0b31c7d2878fc24 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3188.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index 2c08ae60e4a1..b6bde9d12c2b 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -699,7 +699,7 @@ power: power-controller {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pd_vio@RK3188_PD_VIO {
+		power-domain@RK3188_PD_VIO {
 			reg = <RK3188_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -721,7 +721,7 @@ pd_vio@RK3188_PD_VIO {
 				 <&qos_rga>;
 		};
 
-		pd_video@RK3188_PD_VIDEO {
+		power-domain@RK3188_PD_VIDEO {
 			reg = <RK3188_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
@@ -730,7 +730,7 @@ pd_video@RK3188_PD_VIDEO {
 			pm_qos = <&qos_vpu>;
 		};
 
-		pd_gpu@RK3188_PD_GPU {
+		power-domain@RK3188_PD_GPU {
 			reg = <RK3188_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 011/108] ARM: dts: rockchip: Fix power-controller node names for rk3288

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit 970cdc53cb1afa73602028c103dbfb6a230080be ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3288.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 1e6594f8a293..d6dbfbd99568 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -765,7 +765,7 @@ power: power-controller {
 			 *	*_HDMI		HDMI
 			 *	*_MIPI_*	MIPI
 			 */
-			pd_vio@RK3288_PD_VIO {
+			power-domain@RK3288_PD_VIO {
 				reg = <RK3288_PD_VIO>;
 				clocks = <&cru ACLK_IEP>,
 					 <&cru ACLK_ISP>,
@@ -807,7 +807,7 @@ pd_vio@RK3288_PD_VIO {
 			 * Note: The following 3 are HEVC(H.265) clocks,
 			 * and on the ACLK_HEVC_NIU (NOC).
 			 */
-			pd_hevc@RK3288_PD_HEVC {
+			power-domain@RK3288_PD_HEVC {
 				reg = <RK3288_PD_HEVC>;
 				clocks = <&cru ACLK_HEVC>,
 					 <&cru SCLK_HEVC_CABAC>,
@@ -821,7 +821,7 @@ pd_hevc@RK3288_PD_HEVC {
 			 * (video endecoder & decoder) clocks that on the
 			 * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC).
 			 */
-			pd_video@RK3288_PD_VIDEO {
+			power-domain@RK3288_PD_VIDEO {
 				reg = <RK3288_PD_VIDEO>;
 				clocks = <&cru ACLK_VCODEC>,
 					 <&cru HCLK_VCODEC>;
@@ -832,7 +832,7 @@ pd_video@RK3288_PD_VIDEO {
 			 * Note: ACLK_GPU is the GPU clock,
 			 * and on the ACLK_GPU_NIU (NOC).
 			 */
-			pd_gpu@RK3288_PD_GPU {
+			power-domain@RK3288_PD_GPU {
 				reg = <RK3288_PD_GPU>;
 				clocks = <&cru ACLK_GPU>;
 				pm_qos = <&qos_gpu_r>,
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 012/108] arm64: dts: rockchip: Fix power-controller node names for px30

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit d5de0d688ac6e0202674577b05d0726b8a6af401 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/px30.dtsi | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi
index 09baa8a167ce..2b43c3d72dd9 100644
--- a/arch/arm64/boot/dts/rockchip/px30.dtsi
+++ b/arch/arm64/boot/dts/rockchip/px30.dtsi
@@ -244,20 +244,20 @@ power: power-controller {
 			#size-cells = <0>;
 
 			/* These power domains are grouped by VD_LOGIC */
-			pd_usb@PX30_PD_USB {
+			power-domain@PX30_PD_USB {
 				reg = <PX30_PD_USB>;
 				clocks = <&cru HCLK_HOST>,
 					 <&cru HCLK_OTG>,
 					 <&cru SCLK_OTG_ADP>;
 				pm_qos = <&qos_usb_host>, <&qos_usb_otg>;
 			};
-			pd_sdcard@PX30_PD_SDCARD {
+			power-domain@PX30_PD_SDCARD {
 				reg = <PX30_PD_SDCARD>;
 				clocks = <&cru HCLK_SDMMC>,
 					 <&cru SCLK_SDMMC>;
 				pm_qos = <&qos_sdmmc>;
 			};
-			pd_gmac@PX30_PD_GMAC {
+			power-domain@PX30_PD_GMAC {
 				reg = <PX30_PD_GMAC>;
 				clocks = <&cru ACLK_GMAC>,
 					 <&cru PCLK_GMAC>,
@@ -265,7 +265,7 @@ pd_gmac@PX30_PD_GMAC {
 					 <&cru SCLK_GMAC_RX_TX>;
 				pm_qos = <&qos_gmac>;
 			};
-			pd_mmc_nand@PX30_PD_MMC_NAND {
+			power-domain@PX30_PD_MMC_NAND {
 				reg = <PX30_PD_MMC_NAND>;
 				clocks =  <&cru HCLK_NANDC>,
 					  <&cru HCLK_EMMC>,
@@ -278,14 +278,14 @@ pd_mmc_nand@PX30_PD_MMC_NAND {
 				pm_qos = <&qos_emmc>, <&qos_nand>,
 					 <&qos_sdio>, <&qos_sfc>;
 			};
-			pd_vpu@PX30_PD_VPU {
+			power-domain@PX30_PD_VPU {
 				reg = <PX30_PD_VPU>;
 				clocks = <&cru ACLK_VPU>,
 					 <&cru HCLK_VPU>,
 					 <&cru SCLK_CORE_VPU>;
 				pm_qos = <&qos_vpu>, <&qos_vpu_r128>;
 			};
-			pd_vo@PX30_PD_VO {
+			power-domain@PX30_PD_VO {
 				reg = <PX30_PD_VO>;
 				clocks = <&cru ACLK_RGA>,
 					 <&cru ACLK_VOPB>,
@@ -301,7 +301,7 @@ pd_vo@PX30_PD_VO {
 				pm_qos = <&qos_rga_rd>, <&qos_rga_wr>,
 					 <&qos_vop_m0>, <&qos_vop_m1>;
 			};
-			pd_vi@PX30_PD_VI {
+			power-domain@PX30_PD_VI {
 				reg = <PX30_PD_VI>;
 				clocks = <&cru ACLK_CIF>,
 					 <&cru ACLK_ISP>,
@@ -312,7 +312,7 @@ pd_vi@PX30_PD_VI {
 					 <&qos_isp_wr>, <&qos_isp_m1>,
 					 <&qos_vip>;
 			};
-			pd_gpu@PX30_PD_GPU {
+			power-domain@PX30_PD_GPU {
 				reg = <PX30_PD_GPU>;
 				clocks = <&cru SCLK_GPU>;
 				pm_qos = <&qos_gpu>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 013/108] arm64: dts: rockchip: Fix power-controller node names for rk3328

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit 6e6a282b49c6db408d27231e3c709fbdf25e3c1b ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-7-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3328.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 3ed69ecbcf3c..d2d8b675c9e9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -300,13 +300,13 @@ power: power-controller {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			pd_hevc@RK3328_PD_HEVC {
+			power-domain@RK3328_PD_HEVC {
 				reg = <RK3328_PD_HEVC>;
 			};
-			pd_video@RK3328_PD_VIDEO {
+			power-domain@RK3328_PD_VIDEO {
 				reg = <RK3328_PD_VIDEO>;
 			};
-			pd_vpu@RK3328_PD_VPU {
+			power-domain@RK3328_PD_VPU {
 				reg = <RK3328_PD_VPU>;
 				clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 014/108] arm64: dts: rockchip: Fix power-controller node names for rk3399

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit 148bbe29f9108812c6fedd8a228f9e1ed6b422f7 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-8-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 40 ++++++++++++------------
 1 file changed, 20 insertions(+), 20 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 7c1b69f3a4c1..1703817c7354 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -968,26 +968,26 @@ power: power-controller {
 			#size-cells = <0>;
 
 			/* These power domains are grouped by VD_CENTER */
-			pd_iep@RK3399_PD_IEP {
+			power-domain@RK3399_PD_IEP {
 				reg = <RK3399_PD_IEP>;
 				clocks = <&cru ACLK_IEP>,
 					 <&cru HCLK_IEP>;
 				pm_qos = <&qos_iep>;
 			};
-			pd_rga@RK3399_PD_RGA {
+			power-domain@RK3399_PD_RGA {
 				reg = <RK3399_PD_RGA>;
 				clocks = <&cru ACLK_RGA>,
 					 <&cru HCLK_RGA>;
 				pm_qos = <&qos_rga_r>,
 					 <&qos_rga_w>;
 			};
-			pd_vcodec@RK3399_PD_VCODEC {
+			power-domain@RK3399_PD_VCODEC {
 				reg = <RK3399_PD_VCODEC>;
 				clocks = <&cru ACLK_VCODEC>,
 					 <&cru HCLK_VCODEC>;
 				pm_qos = <&qos_video_m0>;
 			};
-			pd_vdu@RK3399_PD_VDU {
+			power-domain@RK3399_PD_VDU {
 				reg = <RK3399_PD_VDU>;
 				clocks = <&cru ACLK_VDU>,
 					 <&cru HCLK_VDU>;
@@ -996,94 +996,94 @@ pd_vdu@RK3399_PD_VDU {
 			};
 
 			/* These power domains are grouped by VD_GPU */
-			pd_gpu@RK3399_PD_GPU {
+			power-domain@RK3399_PD_GPU {
 				reg = <RK3399_PD_GPU>;
 				clocks = <&cru ACLK_GPU>;
 				pm_qos = <&qos_gpu>;
 			};
 
 			/* These power domains are grouped by VD_LOGIC */
-			pd_edp@RK3399_PD_EDP {
+			power-domain@RK3399_PD_EDP {
 				reg = <RK3399_PD_EDP>;
 				clocks = <&cru PCLK_EDP_CTRL>;
 			};
-			pd_emmc@RK3399_PD_EMMC {
+			power-domain@RK3399_PD_EMMC {
 				reg = <RK3399_PD_EMMC>;
 				clocks = <&cru ACLK_EMMC>;
 				pm_qos = <&qos_emmc>;
 			};
-			pd_gmac@RK3399_PD_GMAC {
+			power-domain@RK3399_PD_GMAC {
 				reg = <RK3399_PD_GMAC>;
 				clocks = <&cru ACLK_GMAC>,
 					 <&cru PCLK_GMAC>;
 				pm_qos = <&qos_gmac>;
 			};
-			pd_sd@RK3399_PD_SD {
+			power-domain@RK3399_PD_SD {
 				reg = <RK3399_PD_SD>;
 				clocks = <&cru HCLK_SDMMC>,
 					 <&cru SCLK_SDMMC>;
 				pm_qos = <&qos_sd>;
 			};
-			pd_sdioaudio@RK3399_PD_SDIOAUDIO {
+			power-domain@RK3399_PD_SDIOAUDIO {
 				reg = <RK3399_PD_SDIOAUDIO>;
 				clocks = <&cru HCLK_SDIO>;
 				pm_qos = <&qos_sdioaudio>;
 			};
-			pd_tcpc0@RK3399_PD_TCPD0 {
+			power-domain@RK3399_PD_TCPD0 {
 				reg = <RK3399_PD_TCPD0>;
 				clocks = <&cru SCLK_UPHY0_TCPDCORE>,
 					 <&cru SCLK_UPHY0_TCPDPHY_REF>;
 			};
-			pd_tcpc1@RK3399_PD_TCPD1 {
+			power-domain@RK3399_PD_TCPD1 {
 				reg = <RK3399_PD_TCPD1>;
 				clocks = <&cru SCLK_UPHY1_TCPDCORE>,
 					 <&cru SCLK_UPHY1_TCPDPHY_REF>;
 			};
-			pd_usb3@RK3399_PD_USB3 {
+			power-domain@RK3399_PD_USB3 {
 				reg = <RK3399_PD_USB3>;
 				clocks = <&cru ACLK_USB3>;
 				pm_qos = <&qos_usb_otg0>,
 					 <&qos_usb_otg1>;
 			};
-			pd_vio@RK3399_PD_VIO {
+			power-domain@RK3399_PD_VIO {
 				reg = <RK3399_PD_VIO>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				pd_hdcp@RK3399_PD_HDCP {
+				power-domain@RK3399_PD_HDCP {
 					reg = <RK3399_PD_HDCP>;
 					clocks = <&cru ACLK_HDCP>,
 						 <&cru HCLK_HDCP>,
 						 <&cru PCLK_HDCP>;
 					pm_qos = <&qos_hdcp>;
 				};
-				pd_isp0@RK3399_PD_ISP0 {
+				power-domain@RK3399_PD_ISP0 {
 					reg = <RK3399_PD_ISP0>;
 					clocks = <&cru ACLK_ISP0>,
 						 <&cru HCLK_ISP0>;
 					pm_qos = <&qos_isp0_m0>,
 						 <&qos_isp0_m1>;
 				};
-				pd_isp1@RK3399_PD_ISP1 {
+				power-domain@RK3399_PD_ISP1 {
 					reg = <RK3399_PD_ISP1>;
 					clocks = <&cru ACLK_ISP1>,
 						 <&cru HCLK_ISP1>;
 					pm_qos = <&qos_isp1_m0>,
 						 <&qos_isp1_m1>;
 				};
-				pd_vo@RK3399_PD_VO {
+				power-domain@RK3399_PD_VO {
 					reg = <RK3399_PD_VO>;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					pd_vopb@RK3399_PD_VOPB {
+					power-domain@RK3399_PD_VOPB {
 						reg = <RK3399_PD_VOPB>;
 						clocks = <&cru ACLK_VOP0>,
 							 <&cru HCLK_VOP0>;
 						pm_qos = <&qos_vop_big_r>,
 							 <&qos_vop_big_w>;
 					};
-					pd_vopl@RK3399_PD_VOPL {
+					power-domain@RK3399_PD_VOPL {
 						reg = <RK3399_PD_VOPL>;
 						clocks = <&cru ACLK_VOP1>,
 							 <&cru HCLK_VOP1>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 016/108] ARM: dts: BCM5301X: Fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit b660269cba748dfd07eb5551a88ff34d5ea0b86e ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts      | 4 ++--
 arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts     | 4 ++--
 arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi          | 4 ++--
 arch/arm/boot/dts/bcm5301x.dtsi                   | 2 +-
 arch/arm/boot/dts/bcm953012k.dts                  | 4 ++--
 arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi | 2 +-
 6 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
index 8636600385fd..c81944cd6d0b 100644
--- a/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
+++ b/arch/arm/boot/dts/bcm4708-luxul-xwc-1000.dts
@@ -24,8 +24,8 @@ memory@0 {
 		reg = <0x00000000 0x08000000>;
 	};
 
-	nand: nand@18028000 {
-		nandcs@0 {
+	nand_controller: nand-controller@18028000 {
+		nand@0 {
 			partitions {
 				compatible = "fixed-partitions";
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
index e635a15041dd..a6e2aeb28675 100644
--- a/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
+++ b/arch/arm/boot/dts/bcm47094-dlink-dir-885l.dts
@@ -25,8 +25,8 @@ memory@0 {
 		      <0x88000000 0x08000000>;
 	};
 
-	nand: nand@18028000 {
-		nandcs@0 {
+	nand_controller: nand-controller@18028000 {
+		nand@0 {
 			partitions {
 				compatible = "fixed-partitions";
 				#address-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
index 925a7c9ce5b7..be9a00ff752d 100644
--- a/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
+++ b/arch/arm/boot/dts/bcm5301x-nand-cs0.dtsi
@@ -6,8 +6,8 @@
  */
 
 / {
-	nand@18028000 {
-		nandcs: nandcs@0 {
+	nand-controller@18028000 {
+		nandcs: nand@0 {
 			compatible = "brcm,nandcs";
 			reg = <0>;
 			#address-cells = <1>;
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 7db72a2f1020..092ec525c01c 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -501,7 +501,7 @@ rng: rng@18004000 {
 		reg = <0x18004000 0x14>;
 	};
 
-	nand: nand@18028000 {
+	nand_controller: nand-controller@18028000 {
 		compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1", "brcm,brcmnand";
 		reg = <0x18028000 0x600>, <0x1811a408 0x600>, <0x18028f00 0x20>;
 		reg-names = "nand", "iproc-idm", "iproc-ext";
diff --git a/arch/arm/boot/dts/bcm953012k.dts b/arch/arm/boot/dts/bcm953012k.dts
index 046c59fb4846..de40bd59a5fa 100644
--- a/arch/arm/boot/dts/bcm953012k.dts
+++ b/arch/arm/boot/dts/bcm953012k.dts
@@ -49,8 +49,8 @@ memory@80000000 {
 	};
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
index 8060178b365d..a5a64d17d9ea 100644
--- a/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
+++ b/arch/arm64/boot/dts/broadcom/bcm4908/bcm4908.dtsi
@@ -306,7 +306,7 @@ nand@1800 {
 			interrupt-names = "nand";
 			status = "okay";
 
-			nandcs: nandcs@0 {
+			nandcs: nand@0 {
 				compatible = "brcm,nandcs";
 				reg = <0>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 017/108] ARM: brcmstb: dts: fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 9a800ce1aada6e0f56b78e4713f4858c8990c1f7 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm7445-bcm97445svmb.dts | 4 ++--
 arch/arm/boot/dts/bcm7445.dtsi             | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts b/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
index 8313b7cad542..f92d2cf85972 100644
--- a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
+++ b/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
@@ -14,10 +14,10 @@ memory@0 {
 	};
 };
 
-&nand {
+&nand_controller {
 	status = "okay";
 
-	nandcs@1 {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <1>;
 		nand-ecc-step-size = <512>;
diff --git a/arch/arm/boot/dts/bcm7445.dtsi b/arch/arm/boot/dts/bcm7445.dtsi
index 58f67c9b830b..5ac2042515b8 100644
--- a/arch/arm/boot/dts/bcm7445.dtsi
+++ b/arch/arm/boot/dts/bcm7445.dtsi
@@ -148,7 +148,7 @@ aon-ctrl@410000 {
 			reg-names = "aon-ctrl", "aon-sram";
 		};
 
-		nand: nand@3e2800 {
+		nand_controller: nand-controller@3e2800 {
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 018/108] ARM: Cygnus: dts: fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit e256b48a3b07ee1ae4bfa60abbf509ba8e386862 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi      | 2 +-
 arch/arm/boot/dts/bcm911360_entphn.dts | 4 ++--
 arch/arm/boot/dts/bcm958300k.dts       | 4 ++--
 arch/arm/boot/dts/bcm958305k.dts       | 4 ++--
 4 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index 0025c88f660c..8ecb7861ce10 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -460,7 +460,7 @@ sdhci1: sdhci@18043000 {
 			status = "disabled";
 		};
 
-		nand: nand@18046000 {
+		nand_controller: nand-controller@18046000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x18046000 0x600>, <0xf8105408 0x600>,
 			      <0x18046f00 0x20>;
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index b2d323f4a5ab..a76c74b44bba 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -82,8 +82,8 @@ &uart3 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index b4a1392bd5a6..dda3e11b711f 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -60,8 +60,8 @@ &uart3 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index 3378683321d3..ea3c6b88b313 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -68,8 +68,8 @@ &uart3 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 019/108] ARM: NSP: dts: fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 0484594be733d5cdf976f55a2d4e8d887f351b69 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-nsp.dtsi     | 2 +-
 arch/arm/boot/dts/bcm958522er.dts  | 4 ++--
 arch/arm/boot/dts/bcm958525er.dts  | 4 ++--
 arch/arm/boot/dts/bcm958525xmc.dts | 4 ++--
 arch/arm/boot/dts/bcm958622hr.dts  | 4 ++--
 arch/arm/boot/dts/bcm958623hr.dts  | 4 ++--
 arch/arm/boot/dts/bcm958625hr.dts  | 4 ++--
 arch/arm/boot/dts/bcm958625k.dts   | 4 ++--
 arch/arm/boot/dts/bcm988312hr.dts  | 4 ++--
 9 files changed, 17 insertions(+), 17 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index b4d2cc70afb1..748df7955ae6 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -269,7 +269,7 @@ mailbox: mailbox@25c00 {
 			dma-coherent;
 		};
 
-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x026000 0x600>,
 			      <0x11b408 0x600>,
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/bcm958522er.dts
index 5443fc079e6e..1f73885ec274 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/bcm958522er.dts
@@ -74,8 +74,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/bcm958525er.dts
index e1e3c26cef19..b6b9ca8b0972 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/bcm958525er.dts
@@ -74,8 +74,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index f161ba2e7e5e..ecf426f6ad5d 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -90,8 +90,8 @@ rtc@68 {
 	};
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/bcm958622hr.dts
index 83cb877d63db..8ca18da981ad 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/bcm958622hr.dts
@@ -78,8 +78,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/bcm958623hr.dts
index 4e106ce1384a..9747378db531 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -78,8 +78,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/bcm958625hr.dts
index cda6cc281e18..0f92b773afb8 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -89,8 +89,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index ffbff0014c65..9e984ca0e6df 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -68,8 +68,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/bcm988312hr.dts
index 3fd39c479a3c..5475dab8181d 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/bcm988312hr.dts
@@ -74,8 +74,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 021/108] ARM: dts: Hurricane 2: Fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit a4528d9029e2eda16e4fc9b9da1de1fbec10ab26 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-hr2.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm-hr2.dtsi b/arch/arm/boot/dts/bcm-hr2.dtsi
index e8df458aad39..84cda16f68a2 100644
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/bcm-hr2.dtsi
@@ -179,7 +179,7 @@ amac0: ethernet@22000 {
 			status = "disabled";
 		};
 
-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x26000 0x600>,
 			      <0x11b408 0x600>,
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 022/108] ARM: dts: BCM5301X: Fix pinmux subnodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit bb95d7d440fefd104c593d9cb20da6d34a474e97 ]

This matches pinmux-node.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm47094.dtsi | 2 +-
 arch/arm/boot/dts/bcm5301x.dtsi | 6 +++---
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/bcm47094.dtsi b/arch/arm/boot/dts/bcm47094.dtsi
index 2a8f7312d1be..6282363313e1 100644
--- a/arch/arm/boot/dts/bcm47094.dtsi
+++ b/arch/arm/boot/dts/bcm47094.dtsi
@@ -11,7 +11,7 @@ / {
 &pinctrl {
 	compatible = "brcm,bcm4709-pinmux";
 
-	pinmux_mdio: mdio {
+	pinmux_mdio: mdio-pins {
 		groups = "mdio_grp";
 		function = "mdio";
 	};
diff --git a/arch/arm/boot/dts/bcm5301x.dtsi b/arch/arm/boot/dts/bcm5301x.dtsi
index 092ec525c01c..5b9723a10bd6 100644
--- a/arch/arm/boot/dts/bcm5301x.dtsi
+++ b/arch/arm/boot/dts/bcm5301x.dtsi
@@ -458,18 +458,18 @@ spi-pins {
 					function = "spi";
 				};
 
-				pinmux_i2c: i2c {
+				pinmux_i2c: i2c-pins {
 					groups = "i2c_grp";
 					function = "i2c";
 				};
 
-				pinmux_pwm: pwm {
+				pinmux_pwm: pwm-pins {
 					groups = "pwm0_grp", "pwm1_grp",
 						 "pwm2_grp", "pwm3_grp";
 					function = "pwm";
 				};
 
-				pinmux_uart1: uart1 {
+				pinmux_uart1: uart1-pins {
 					groups = "uart1_grp";
 					function = "uart1";
 				};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 023/108] soc: bcm: brcmstb: remove unused variable 'brcmstb_machine_match'

[Sasha Levin]

From: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>

[ Upstream commit c1f512182c54dc87efd2f7ac19f16a49ff8bb19e ]

Fix the following clang warning:

drivers/soc/bcm/brcmstb/common.c:17:34: warning: unused variable
'brcmstb_machine_match' [-Wunused-const-variable].

Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/bcm/brcmstb/common.c | 5 -----
 1 file changed, 5 deletions(-)

diff --git a/drivers/soc/bcm/brcmstb/common.c b/drivers/soc/bcm/brcmstb/common.c
index e87dfc6660f3..2a010881f4b6 100644
--- a/drivers/soc/bcm/brcmstb/common.c
+++ b/drivers/soc/bcm/brcmstb/common.c
@@ -14,11 +14,6 @@
 static u32 family_id;
 static u32 product_id;
 
-static const struct of_device_id brcmstb_machine_match[] = {
-	{ .compatible = "brcm,brcmstb", },
-	{ }
-};
-
 u32 brcmstb_get_family_id(void)
 {
 	return family_id;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 024/108] ARM: dts: imx25-pinfunc: Fix gpio function name for pads GPIO_[A-F]

[Sasha Levin]

From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

[ Upstream commit e0cdd26af8eb9001689a4cde4f72c61c1c4b06be ]

The pinfunc definitions used GPIO_A as function instead of GPIO_1_0 as
done for all the other pins with GPIO functionality. Fix for consistency.

There are no mainline users that needs adaption.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx25-pinfunc.h | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h
index f984b702efc5..908caf810351 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/imx25-pinfunc.h
@@ -563,15 +563,15 @@
 #define MX25_PAD_DE_B__DE_B			0x1f0 0x3ec 0x000 0x00 0x000
 #define MX25_PAD_DE_B__GPIO_2_20		0x1f0 0x3ec 0x000 0x05 0x000
 
-#define MX25_PAD_GPIO_A__GPIO_A			0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__GPIO_1_0		0x1f4 0x3f0 0x000 0x00 0x000
 #define MX25_PAD_GPIO_A__CAN1_TX		0x1f4 0x3f0 0x000 0x06 0x000
 #define MX25_PAD_GPIO_A__USBOTG_PWR		0x1f4 0x3f0 0x000 0x02 0x000
 
-#define MX25_PAD_GPIO_B__GPIO_B			0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__GPIO_1_1		0x1f8 0x3f4 0x000 0x00 0x000
 #define MX25_PAD_GPIO_B__USBOTG_OC		0x1f8 0x3f4 0x57c 0x02 0x001
 #define MX25_PAD_GPIO_B__CAN1_RX		0x1f8 0x3f4 0x480 0x06 0x001
 
-#define MX25_PAD_GPIO_C__GPIO_C			0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__GPIO_1_2		0x1fc 0x3f8 0x000 0x00 0x000
 #define MX25_PAD_GPIO_C__PWM4_PWMO		0x1fc 0x3f8 0x000 0x01 0x000
 #define MX25_PAD_GPIO_C__I2C2_SCL		0x1fc 0x3f8 0x51c 0x02 0x001
 #define MX25_PAD_GPIO_C__KPP_COL4		0x1fc 0x3f8 0x52c 0x03 0x001
@@ -580,18 +580,18 @@
 #define MX25_PAD_GPIO_C__CAN2_TX		0x1fc 0x3f8 0x000 0x06 0x000
 #define MX25_PAD_GPIO_C__CSPI2_SS2		0x1fc 0x3f8 0x000 0x07 0x000
 
-#define MX25_PAD_GPIO_D__GPIO_D			0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__GPIO_1_3		0x200 0x3fc 0x000 0x00 0x000
 #define MX25_PAD_GPIO_D__I2C2_SDA		0x200 0x3fc 0x520 0x02 0x001
 #define MX25_PAD_GPIO_D__CAN2_RX		0x200 0x3fc 0x484 0x06 0x001
 #define MX25_PAD_GPIO_D__CSPI3_SS2		0x200 0x3fc 0x4c4 0x07 0x001
 
-#define MX25_PAD_GPIO_E__GPIO_E			0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__GPIO_1_4		0x204 0x400 0x000 0x00 0x000
 #define MX25_PAD_GPIO_E__I2C3_CLK		0x204 0x400 0x524 0x01 0x002
 #define MX25_PAD_GPIO_E__LD16			0x204 0x400 0x000 0x02 0x000
 #define MX25_PAD_GPIO_E__AUD7_TXD		0x204 0x400 0x000 0x04 0x000
 #define MX25_PAD_GPIO_E__UART4_RXD		0x204 0x400 0x570 0x06 0x002
 
-#define MX25_PAD_GPIO_F__GPIO_F			0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__GPIO_1_5		0x208 0x404 0x000 0x00 0x000
 #define MX25_PAD_GPIO_F__LD17			0x208 0x404 0x000 0x02 0x000
 #define MX25_PAD_GPIO_F__AUD7_TXC		0x208 0x404 0x000 0x04 0x000
 #define MX25_PAD_GPIO_F__UART4_TXD		0x208 0x404 0x000 0x06 0x000
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 5.13 024/108] ARM: dts: imx25-pinfunc: Fix gpio function name for pads GPIO_[A-F]

[Uwe Kleine-König]

[-- Attachment #1.1: Type: text/plain, Size: 997 bytes --]

On Wed, Jul 14, 2021 at 03:36:36PM -0400, Sasha Levin wrote:
> From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> 
> [ Upstream commit e0cdd26af8eb9001689a4cde4f72c61c1c4b06be ]
> 
> The pinfunc definitions used GPIO_A as function instead of GPIO_1_0 as
> done for all the other pins with GPIO functionality. Fix for consistency.
> 
> There are no mainline users that needs adaption.
> 
> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
> Signed-off-by: Sasha Levin <sashal@kernel.org>

I'm not convinced it's a good idea to take this patch for stable.
in-tree users are unaffected and the only effect this can have on
out-of-tree users is to break them. So the gain of having this is not
positive.

Am I missing something?

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 5.13 024/108] ARM: dts: imx25-pinfunc: Fix gpio function name for pads GPIO_[A-F]

[Sasha Levin]

On Wed, Jul 14, 2021 at 10:35:50PM +0200, Uwe Kleine-König wrote:
>On Wed, Jul 14, 2021 at 03:36:36PM -0400, Sasha Levin wrote:
>> From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
>>
>> [ Upstream commit e0cdd26af8eb9001689a4cde4f72c61c1c4b06be ]
>>
>> The pinfunc definitions used GPIO_A as function instead of GPIO_1_0 as
>> done for all the other pins with GPIO functionality. Fix for consistency.
>>
>> There are no mainline users that needs adaption.
>>
>> Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
>> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
>> Signed-off-by: Sasha Levin <sashal@kernel.org>
>
>I'm not convinced it's a good idea to take this patch for stable.
>in-tree users are unaffected and the only effect this can have on
>out-of-tree users is to break them. So the gain of having this is not
>positive.
>
>Am I missing something?

Hm, if those definitions don't have an in-tree users, why are they still
around to begin with?

-- 
Thanks,
Sasha

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH AUTOSEL 5.13 024/108] ARM: dts: imx25-pinfunc: Fix gpio function name for pads GPIO_[A-F]

[Uwe Kleine-König]

[-- Attachment #1.1: Type: text/plain, Size: 1505 bytes --]

On Wed, Jul 14, 2021 at 04:59:21PM -0400, Sasha Levin wrote:
> On Wed, Jul 14, 2021 at 10:35:50PM +0200, Uwe Kleine-König wrote:
> > On Wed, Jul 14, 2021 at 03:36:36PM -0400, Sasha Levin wrote:
> > > From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> > > 
> > > [ Upstream commit e0cdd26af8eb9001689a4cde4f72c61c1c4b06be ]
> > > 
> > > The pinfunc definitions used GPIO_A as function instead of GPIO_1_0 as
> > > done for all the other pins with GPIO functionality. Fix for consistency.
> > > 
> > > There are no mainline users that needs adaption.
> > > 
> > > Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
> > > Signed-off-by: Shawn Guo <shawnguo@kernel.org>
> > > Signed-off-by: Sasha Levin <sashal@kernel.org>
> > 
> > I'm not convinced it's a good idea to take this patch for stable.
> > in-tree users are unaffected and the only effect this can have on
> > out-of-tree users is to break them. So the gain of having this is not
> > positive.
> > 
> > Am I missing something?
> 
> Hm, if those definitions don't have an in-tree users, why are they still
> around to begin with?

It's hardware description and out-of-tree dts might make use of it. Even
if no in-tree user benefits, it's IMO better to have this included, but
I admit you could judge differently here.

Best regards
Uwe

-- 
Pengutronix e.K.                           | Uwe Kleine-König            |
Industrial Linux Solutions                 | https://www.pengutronix.de/ |

[-- Attachment #1.2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

[-- Attachment #2: Type: text/plain, Size: 176 bytes --]

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 025/108] ARM: dts: exynos: align Broadcom WiFi with dtschema

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

[ Upstream commit cc29e39412b9a78b43f7dfa09d739f8ba9fa7984 ]

The Broadcom BCM4329 family dtschema expects devices to be compatible
also with brcm,bcm4329-fmac:

  arch/arm/boot/dts/exynos3250-rinato.dt.yaml: wifi@1: compatible: 'oneOf' conditional failed, one must be fixed:
    ['brcm,bcm4334-fmac'] is too short
    'brcm,bcm4329-fmac' was expected

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/exynos3250-rinato.dts         | 2 +-
 arch/arm/boot/dts/exynos4210-i9100.dts          | 2 +-
 arch/arm/boot/dts/exynos4210-trats.dts          | 2 +-
 arch/arm/boot/dts/exynos4210-universal_c210.dts | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index c52b9cf4f74c..f6ba5e426040 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -653,7 +653,7 @@ &mshc_1 {
 	mmc-pwrseq = <&wlan_pwrseq>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4334-fmac";
+		compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 
 		interrupt-parent = <&gpx1>;
diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts
index 525ff3d2fac3..db70f62cc08f 100644
--- a/arch/arm/boot/dts/exynos4210-i9100.dts
+++ b/arch/arm/boot/dts/exynos4210-i9100.dts
@@ -806,7 +806,7 @@ &sdhci_3 {
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4330-fmac";
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 
 		interrupt-parent = <&gpx2>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index d2406c9146b8..3eb8df319246 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -521,7 +521,7 @@ &sdhci_3 {
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4330-fmac";
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 
 		interrupt-parent = <&gpx2>;
diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts
index dd44ad2c6ad6..f052853244a4 100644
--- a/arch/arm/boot/dts/exynos4210-universal_c210.dts
+++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts
@@ -614,7 +614,7 @@ &sdhci_3 {
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4330-fmac";
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpx2>;
 		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 026/108] soc: mediatek: add missing MODULE_DEVICE_TABLE

[Sasha Levin]

From: Zou Wei <zou_wei@huawei.com>

[ Upstream commit ba96de3ae5a7e2121cac80053b277eb2ab51a0ae ]

This patch adds missing MODULE_DEVICE_TABLE definition which generates
correct modalias for automatic loading of this driver when it is built
as an external module.

Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1620705350-104687-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/soc/mediatek/mtk-devapc.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/soc/mediatek/mtk-devapc.c b/drivers/soc/mediatek/mtk-devapc.c
index f1cea041dc5a..7c65ad3d1f8a 100644
--- a/drivers/soc/mediatek/mtk-devapc.c
+++ b/drivers/soc/mediatek/mtk-devapc.c
@@ -234,6 +234,7 @@ static const struct of_device_id mtk_devapc_dt_match[] = {
 	}, {
 	},
 };
+MODULE_DEVICE_TABLE(of, mtk_devapc_dt_match);
 
 static int mtk_devapc_probe(struct platform_device *pdev)
 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 027/108] ARM: dts: imx6: phyFLEX: Fix UART hardware flow control

[Sasha Levin]

From: Primoz Fiser <primoz.fiser@norik.com>

[ Upstream commit 14cdc1f243d79e0b46be150502b7dba9c5a6bdfd ]

Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.

Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.

Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
index 7bd658b7bdda..f3236204cb5a 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -322,8 +322,8 @@ pinctrl_uart3: uart3grp {
 			fsl,pins = <
 				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
 				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D30__UART3_RTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_CTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
 			>;
 		};
 
@@ -410,6 +410,7 @@ &reg_soc {
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
 	status = "disabled";
 };
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 028/108] ARM: imx: pm-imx5: Fix references to imx5_cpu_suspend_info

[Sasha Levin]

From: Jonathan Neuschäfer <j.neuschaefer@gmx.net>

[ Upstream commit 89b759469d525f4d5f9c29cd3b1f490311c67f85 ]

The name of the struct, as defined in arch/arm/mach-imx/pm-imx5.c,
is imx5_cpu_suspend_info.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-imx/suspend-imx53.S | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-imx/suspend-imx53.S b/arch/arm/mach-imx/suspend-imx53.S
index 41b8aad65363..46570ec2fbcf 100644
--- a/arch/arm/mach-imx/suspend-imx53.S
+++ b/arch/arm/mach-imx/suspend-imx53.S
@@ -28,11 +28,11 @@
  *                              ^
  *                              ^
  *                      imx53_suspend code
- *              PM_INFO structure(imx53_suspend_info)
+ *              PM_INFO structure(imx5_cpu_suspend_info)
  * ======================== low address =======================
  */
 
-/* Offsets of members of struct imx53_suspend_info */
+/* Offsets of members of struct imx5_cpu_suspend_info */
 #define SUSPEND_INFO_MX53_M4IF_V_OFFSET		0x0
 #define SUSPEND_INFO_MX53_IOMUXC_V_OFFSET	0x4
 #define SUSPEND_INFO_MX53_IO_COUNT_OFFSET	0x8
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 029/108] arm64: dts: rockchip: fix regulator-gpio states array

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit b82f8e2992534aab0fa762a37376be30df263701 ]

A test with the command below gives this error:

/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long

dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts       | 4 ++--
 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts   | 4 ++--
 arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts       | 4 ++--
 arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi | 2 +-
 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi         | 4 ++--
 5 files changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
index 3dddd4742c3a..665b2e69455d 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
@@ -84,8 +84,8 @@ vcc_sdmmc: vcc-sdmmc {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 		gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x0
-			  3300000 0x1>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
 		vin-supply = <&vcc5v0_sys>;
 	};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
index f807bc066ccb..d5001d13e374 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
@@ -76,8 +76,8 @@ vcc_io_sdio: sdmmcio-regulator {
 		regulator-settling-time-us = <5000>;
 		regulator-type = "voltage";
 		startup-delay-us = <2000>;
-		states = <1800000 0x1
-			  3300000 0x0>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
 		vin-supply = <&vcc_io_33>;
 	};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
index a05732b59f38..a99979afd373 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -50,8 +50,8 @@ vcc_sd: sdmmc-regulator {
 	vcc_sdio: sdmmcio-regulator {
 		compatible = "regulator-gpio";
 		gpios = <&grf_gpio 0 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1
-			  3300000 0x0>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
 		regulator-name = "vcc_sdio";
 		regulator-type = "voltage";
 		regulator-min-microvolt = <1800000>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
index beee5fbb3443..5d7a9d96d163 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
@@ -245,7 +245,7 @@ &ppvar_gpu_pwm {
 };
 
 &ppvar_sd_card_io {
-	states = <1800000 0x0 3300000 0x1>;
+	states = <1800000 0x0>, <3300000 0x1>;
 	regulator-max-microvolt = <3300000>;
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index 4002742fed4c..c1bcc8ca3769 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -252,8 +252,8 @@ ppvar_sd_card_io: ppvar-sd-card-io {
 		enable-active-high;
 		enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1
-			  3000000 0x0>;
+		states = <1800000 0x1>,
+			 <3000000 0x0>;
 
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3000000>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 030/108] ARM: dts: ux500: Fix interrupt cells

[Sasha Levin]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

[ Upstream commit e4ff0112a03c2e353c8457cd33c88feb89dfec41 ]

Fix interrupt cells in DT AB8500/AB8505 source files. The
compiled DTB files will stay the same.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ab8500.dtsi | 26 +++++++++++++-------------
 arch/arm/boot/dts/ste-ab8505.dtsi | 22 +++++++++++-----------
 2 files changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
index a16a00fb5fa5..f78b41002490 100644
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -42,15 +42,15 @@ ab8500_gpio: ab8500-gpio {
 
 				ab8500-rtc {
 					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};
 
 				gpadc: ab8500-gpadc {
 					compatible = "stericsson,ab8500-gpadc";
-					interrupts = <32 IRQ_TYPE_LEVEL_HIGH
-						      39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH>,
+						     <39 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "HW_CONV_END", "SW_CONV_END";
 					vddadc-supply = <&ab8500_ldo_tvout_reg>;
 					#address-cells = <1>;
@@ -219,13 +219,13 @@ ab8500_chargalg {
 
 				ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ID_WAKEUP_R",
 							  "ID_WAKEUP_F",
 							  "VBUS_DET_F",
@@ -242,8 +242,8 @@ ab8500_usb {
 
 				ab8500-ponkey {
 					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
 				};
 
diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi
index cc045b2fc217..3380afa74c14 100644
--- a/arch/arm/boot/dts/ste-ab8505.dtsi
+++ b/arch/arm/boot/dts/ste-ab8505.dtsi
@@ -39,8 +39,8 @@ ab8505_gpio: ab8505-gpio {
 
 				ab8500-rtc {
 					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};
 
@@ -182,13 +182,13 @@ ab8500_chargalg {
 
 				ab8500_usb: ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ID_WAKEUP_R",
 							  "ID_WAKEUP_F",
 							  "VBUS_DET_F",
@@ -205,8 +205,8 @@ ab8500_usb: ab8500_usb {
 
 				ab8500-ponkey {
 					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
 				};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 031/108] ARM: dts: ux500: Rename gpio-controller node

[Sasha Levin]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

[ Upstream commit 4917b702818872fdf2a9973705af3aa7d3d1f19e ]

Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ab8500.dtsi      | 2 +-
 arch/arm/boot/dts/ste-ab8505.dtsi      | 2 +-
 arch/arm/boot/dts/ste-href-ab8500.dtsi | 2 +-
 arch/arm/boot/dts/ste-href.dtsi        | 2 +-
 arch/arm/boot/dts/ste-snowball.dts     | 2 +-
 5 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
index f78b41002490..d0fe3f9aa183 100644
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -34,7 +34,7 @@ ab8500_clock: clock-controller {
 					#clock-cells = <1>;
 				};
 
-				ab8500_gpio: ab8500-gpio {
+				ab8500_gpio: ab8500-gpiocontroller {
 					compatible = "stericsson,ab8500-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi
index 3380afa74c14..0defc15b9bbc 100644
--- a/arch/arm/boot/dts/ste-ab8505.dtsi
+++ b/arch/arm/boot/dts/ste-ab8505.dtsi
@@ -31,7 +31,7 @@ ab8500_clock: clock-controller {
 					#clock-cells = <1>;
 				};
 
-				ab8505_gpio: ab8505-gpio {
+				ab8505_gpio: ab8505-gpiocontroller {
 					compatible = "stericsson,ab8505-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/ste-href-ab8500.dtsi
index 4946743de7b9..3ccb7b5c7162 100644
--- a/arch/arm/boot/dts/ste-href-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi
@@ -9,7 +9,7 @@ / {
 	soc {
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 					/* Hog a few default settings */
 					pinctrl-names = "default";
 					pinctrl-0 = <&gpio2_default_mode>,
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index 83b179692dff..7566b4963ef6 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -202,7 +202,7 @@ msp3: msp@80125000 {
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 				};
 
 				ab8500_usb {
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index b344b3748143..40f1d7c9c1d4 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -376,7 +376,7 @@ spi@80002000 {
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 					/*
 					 * AB8500 GPIOs are numbered starting from 1, so the first
 					 * index 0 is what in the datasheet is called "GPIO1", and
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 032/108] ARM: dts: ux500: Fix orientation of accelerometer

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit 4beba4011995a2c44ee27e1d358dc32e6b9211b3 ]

This adds a mounting matrix to the accelerometer
on the TVK1281618 R3.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
index 70f058352efc..511e097cc33e 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
@@ -89,6 +89,9 @@ accelerometer@19 {
 					     <19 IRQ_TYPE_EDGE_RISING>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
 			};
 			magnetometer@1e {
 				compatible = "st,lsm303dlm-magn";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 033/108] ARM: dts: ux500: Fix some compatible strings

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit 59ba546d1662c4beb738725965041f350afe24b4 ]

The Golden and Skomer phones have BCM4334 WLAN+BT chips,
so make the compatible strings reflect the new available
bindings for these.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ux500-samsung-golden.dts | 3 ++-
 arch/arm/boot/dts/ste-ux500-samsung-janice.dts | 4 ++--
 arch/arm/boot/dts/ste-ux500-samsung-skomer.dts | 3 ++-
 3 files changed, 6 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
index 0d43ee6583cf..40df7c61bf69 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-golden.dts
@@ -121,7 +121,7 @@ mmc@80118000 {
 			#size-cells = <0>;
 
 			wifi@1 {
-				compatible = "brcm,bcm4329-fmac";
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 				reg = <1>;
 
 				/* GPIO216 (WLAN_HOST_WAKE) */
@@ -162,6 +162,7 @@ uart@80120000 {
 			pinctrl-1 = <&u0_a_1_sleep>;
 
 			bluetooth {
+				/* BCM4334B0 actually */
 				compatible = "brcm,bcm4330-bt";
 				/* GPIO222 (BT_VREG_ON) */
 				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
index f24369873ce2..eaf8039d10ad 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
@@ -401,8 +401,7 @@ mmc@80118000 {
 			status = "okay";
 
 			wifi@1 {
-				/* Actually BRCM4330 */
-				compatible = "brcm,bcm4329-fmac";
+				compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 				reg = <1>;
 				/* GPIO216 WL_HOST_WAKE */
 				interrupt-parent = <&gpio6>;
@@ -436,6 +435,7 @@ uart@80120000 {
 			status = "okay";
 
 			bluetooth {
+				/* BCM4330B1 actually */
 				compatible = "brcm,bcm4330-bt";
 				/* GPIO222 rail BT_VREG_EN to BT_REG_ON */
 				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
index d28a00757d0b..94afd7a0fe1f 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-skomer.dts
@@ -211,7 +211,7 @@ mmc@80118000 {
 			#size-cells = <0>;
 
 			wifi@1 {
-				compatible = "brcm,bcm4329-fmac";
+				compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 				reg = <1>;
 				/* GPIO216 WL_HOST_WAKE */
 				interrupt-parent = <&gpio6>;
@@ -247,6 +247,7 @@ uart@80120000 {
 
 			/* FIXME: not quite working yet, probably needs regulators */
 			bluetooth {
+				/* BCM4334B0 actually */
 				compatible = "brcm,bcm4330-bt";
 				shutdown-gpios = <&gpio6 30 GPIO_ACTIVE_HIGH>;
 				device-wakeup-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 034/108] ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE value

[Sasha Levin]

From: Oleksij Rempel <o.rempel@pengutronix.de>

[ Upstream commit 723de6a4126b2474a8106e943749e1554012dad6 ]

Without SoC specific PHY fixups the network interface on this board will
fail to work. Provide missing DT properties to make it work again.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index 065d3ab0f50a..e7d9bfbfd0e4 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -106,6 +106,8 @@ rgmii_phy: ethernet-phy@4 {
 			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
 			reset-deassert-us = <1000>;
+			qca,smarteee-tw-us-1g = <24>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 035/108] ARM: dts: ux500: Fix orientation of Janice accelerometer

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit e409c1e1d5cb164361229e3a3f084e4a32544fb6 ]

This fixes up the axis on the Janice accelerometer to give
the right orientation according to tests.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ux500-samsung-janice.dts | 7 +++----
 1 file changed, 3 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
index eaf8039d10ad..25af066f6f3a 100644
--- a/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
+++ b/arch/arm/boot/dts/ste-ux500-samsung-janice.dts
@@ -583,10 +583,9 @@ i2c-gate {
 					accelerometer@08 {
 						compatible = "bosch,bma222";
 						reg = <0x08>;
-						/* FIXME: no idea about this */
-						mount-matrix = "1", "0", "0",
-							       "0", "1", "0",
-							       "0", "0", "1";
+						mount-matrix = "0", "1", "0",
+							       "-1", "0", "0",
+							       "0", "0", "-1";
 						vddio-supply = <&ab8500_ldo_aux2_reg>; // 1.8V
 						vdd-supply = <&ab8500_ldo_aux1_reg>; // 3V
 					};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 050/108] arm64: dts: ti: k3-am654x/j721e/j7200-common-proc-board: Fix MCU_RGMII1_TXC direction

[Sasha Levin]

From: Grygorii Strashko <grygorii.strashko@ti.com>

[ Upstream commit 69db725cdb2b803af67897a08ea54467d11f6020 ]

The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.

Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts        | 2 +-
 arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index eddb2ffb93ca..97c344088483 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -136,7 +136,7 @@ AM65X_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* (L2) MCU_RGMII1_RD3 */
 			AM65X_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* (L5) MCU_RGMII1_RD2 */
 			AM65X_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* (M6) MCU_RGMII1_RD1 */
 			AM65X_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* (L6) MCU_RGMII1_RD0 */
-			AM65X_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* (N1) MCU_RGMII1_TXC */
+			AM65X_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* (N1) MCU_RGMII1_TXC */
 			AM65X_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* (M1) MCU_RGMII1_RXC */
 		>;
 	};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index bedd01b7a32c..d14f3c18b65f 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -90,7 +90,7 @@ J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
 			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
 			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
 			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
 			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 60764366e22b..351bb84db65b 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -237,7 +237,7 @@ J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
 			J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
 			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
 			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
 			J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 057/108] ARM: dts: stm32: Remove extra size-cells on dhcom-pdk2

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 28b9a4679d8074512f12967497c161b992eb3b75 ]

Fix make dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: gpio-keys-polled: '#address-cells' is a dependency of '#size-cells'
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: gpio-keys: '#address-cells' is a dependency of '#size-cells'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index 5523f4138fd6..0fbf9913e8df 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -34,7 +34,6 @@ display_bl: display-bl {
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#size-cells = <0>;
 		poll-interval = <20>;
 
 		/*
@@ -60,7 +59,6 @@ button-2 {
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#size-cells = <0>;
 
 		button-1 {
 			label = "TA2-GPIO-B";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 058/108] ARM: dts: stm32: Fix touchscreen node on dhcom-pdk2

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 4b5fadef3fc2ab8863ffdf31eed6a745b1bf6e61 ]

Fix make dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml:0:0: /soc/i2c@40015000/polytouch@38: failed to match any schema with compatible: ['edt,edt-ft5x06']

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index 0fbf9913e8df..b8c8f0b284c3 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -182,8 +182,8 @@ sgtl5000_rx_endpoint: endpoint@1 {
 
 	};
 
-	polytouch@38 {
-		compatible = "edt,edt-ft5x06";
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
 		reg = <0x38>;
 		interrupt-parent = <&gpiog>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 059/108] ARM: dts: stm32: fix stm32mp157c-odyssey card detect pin

[Sasha Levin]

From: Grzegorz Szymaszek <gszymaszek@short.pl>

[ Upstream commit 0171b07373cc8c2815ca5fa79a7308fdefa54ca4 ]

The microSD card detect pin is physically connected to the MPU pin PI3.
The Device Tree configuration of the card detect pin was wrong—it was
set to pin PB7 instead. If such configuration was used, the kernel would
hang on “Waiting for root device” when booting from a microSD card.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157c-odyssey.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
index a7ffec8f1516..be1dd5e9e744 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey.dts
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -64,7 +64,7 @@ &sdmmc1 {
 	pinctrl-0 = <&sdmmc1_b4_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
-	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	disable-wp;
 	st,neg-edge;
 	bus-width = <4>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 060/108] ARM: dts: stm32: fix gpio-keys node on STM32 MCU boards

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit bf24b91f4baf7e421c770a1d9c7d381b10206ac9 ]

Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.

Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32429i-eval.dts  | 8 +++-----
 arch/arm/boot/dts/stm32746g-eval.dts  | 6 ++----
 arch/arm/boot/dts/stm32f429-disco.dts | 6 ++----
 arch/arm/boot/dts/stm32f469-disco.dts | 6 ++----
 arch/arm/boot/dts/stm32f769-disco.dts | 6 ++----
 5 files changed, 11 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/stm32429i-eval.dts b/arch/arm/boot/dts/stm32429i-eval.dts
index 7e10ae744c9d..9ac1ffe53413 100644
--- a/arch/arm/boot/dts/stm32429i-eval.dts
+++ b/arch/arm/boot/dts/stm32429i-eval.dts
@@ -119,17 +119,15 @@ led-blue {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 0>;
 		};
-		button@1 {
+		button-1 {
 			label = "Tamper";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioc 13 0>;
diff --git a/arch/arm/boot/dts/stm32746g-eval.dts b/arch/arm/boot/dts/stm32746g-eval.dts
index ca8c192449ee..327613fd9666 100644
--- a/arch/arm/boot/dts/stm32746g-eval.dts
+++ b/arch/arm/boot/dts/stm32746g-eval.dts
@@ -81,12 +81,10 @@ led-blue {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioc 13 0>;
diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
index 3dc068b91ca1..075ac57d0bf4 100644
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/stm32f429-disco.dts
@@ -81,12 +81,10 @@ led-green {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 0>;
diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
index 2e1b3bbbe4b5..8c982ae79f43 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -104,12 +104,10 @@ led-blue {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/stm32f769-disco.dts b/arch/arm/boot/dts/stm32f769-disco.dts
index 0ce7fbc20fa4..be943b701980 100644
--- a/arch/arm/boot/dts/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/stm32f769-disco.dts
@@ -75,12 +75,10 @@ led-red {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 061/108] ARM: dts: stm32: fix RCC node name on stm32f429 MCU

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit e4b948415a89a219d13e454011cdcf9e63ecc529 ]

This prevent warning observed with "make dtbs_check W=1"

Warning (simple_bus_reg): /soc/rcc@40023810: simple-bus unit address format
error, expected "40023800"

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f429.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index f6530d724d00..41e0087bdbf9 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -709,7 +709,7 @@ crc: crc@40023000 {
 			status = "disabled";
 		};
 
-		rcc: rcc@40023810 {
+		rcc: rcc@40023800 {
 			#reset-cells = <1>;
 			#clock-cells = <2>;
 			compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 062/108] ARM: dts: stm32: fix timer nodes on STM32 MCU to prevent warnings

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit 2388f14d8747f8304e26ee870790e188c9431efd ]

Prevent warning seen with "make dtbs_check W=1" command:

Warning (avoid_unnecessary_addr_size): /soc/timers@40001c00: unnecessary
address-cells/size-cells without "ranges" or child "reg" property

Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f429.dtsi | 8 --------
 arch/arm/boot/dts/stm32f746.dtsi | 8 --------
 arch/arm/boot/dts/stm32h743.dtsi | 4 ----
 3 files changed, 20 deletions(-)

diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index 41e0087bdbf9..8748d5850298 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -283,8 +283,6 @@ timer@11 {
 		};
 
 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM13)>;
@@ -299,8 +297,6 @@ pwm {
 		};
 
 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM14)>;
@@ -633,8 +629,6 @@ timer@8 {
 		};
 
 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM10)>;
@@ -649,8 +643,6 @@ pwm {
 		};
 
 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM11)>;
diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi
index e1df603fc981..72c1b76684b6 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -265,8 +265,6 @@ timer@11 {
 		};
 
 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM13)>;
@@ -281,8 +279,6 @@ pwm {
 		};
 
 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM14)>;
@@ -531,8 +527,6 @@ timer@8 {
 		};
 
 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM10)>;
@@ -547,8 +541,6 @@ pwm {
 		};
 
 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM11)>;
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
index 05ecdf9ff03a..6e42ca2dada2 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -485,8 +485,6 @@ trigger@2 {
 		};
 
 		lptimer4: timer@58002c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58002c00 0x400>;
 			clocks = <&rcc LPTIM4_CK>;
@@ -501,8 +499,6 @@ pwm {
 		};
 
 		lptimer5: timer@58003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58003000 0x400>;
 			clocks = <&rcc LPTIM5_CK>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 064/108] firmware: arm_scmi: Add SMCCC discovery dependency in Kconfig

[Sasha Levin]

From: Etienne Carriere <etienne.carriere@linaro.org>

[ Upstream commit c05b07963e965ae34e75ee8c33af1095350cd87e ]

ARM_SCMI_PROTOCOL depends on either MAILBOX or HAVE_ARM_SMCCC_DISCOVERY,
not MAILBOX alone. Fix the depedency in Kconfig file and driver to
reflect the same.

Link: https://lore.kernel.org/r/20210521134055.24271-1-etienne.carriere@linaro.org
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[sudeep.holla: Minor tweaks to subject and change log]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/Kconfig           | 2 +-
 drivers/firmware/arm_scmi/common.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
index db0ea2d2d75a..a9c613c32282 100644
--- a/drivers/firmware/Kconfig
+++ b/drivers/firmware/Kconfig
@@ -9,7 +9,7 @@ menu "Firmware Drivers"
 config ARM_SCMI_PROTOCOL
 	tristate "ARM System Control and Management Interface (SCMI) Message Protocol"
 	depends on ARM || ARM64 || COMPILE_TEST
-	depends on MAILBOX
+	depends on MAILBOX || HAVE_ARM_SMCCC_DISCOVERY
 	help
 	  ARM System Control and Management Interface (SCMI) protocol is a
 	  set of operating system-independent software interfaces that are
diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
index 228bf4a71d23..8685619d38f9 100644
--- a/drivers/firmware/arm_scmi/common.h
+++ b/drivers/firmware/arm_scmi/common.h
@@ -331,7 +331,7 @@ struct scmi_desc {
 };
 
 extern const struct scmi_desc scmi_mailbox_desc;
-#ifdef CONFIG_HAVE_ARM_SMCCC
+#ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
 extern const struct scmi_desc scmi_smc_desc;
 #endif
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 065/108] firmware: arm_scmi: Fix the build when CONFIG_MAILBOX is not selected

[Sasha Levin]

From: Sudeep Holla <sudeep.holla@arm.com>

[ Upstream commit ab7766b72855e6a68109b915d071181b93086e29 ]

0day CI kernel test robot reported following build error with randconfig

aarch64-linux-ld: drivers/firmware/arm_scmi/driver.o:(.rodata+0x1e0):
		undefined reference to `scmi_mailbox_desc'

Fix the error by adding CONFIG_MAILBOX dependency for scmi_mailbox_desc.

Link: https://lore.kernel.org/r/20210603072631.1660963-1-sudeep.holla@arm.com
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/arm_scmi/driver.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
index 66eb3f0e5daf..41d80bbaa9a2 100644
--- a/drivers/firmware/arm_scmi/driver.c
+++ b/drivers/firmware/arm_scmi/driver.c
@@ -1567,7 +1567,9 @@ ATTRIBUTE_GROUPS(versions);
 
 /* Each compatible listed below must have descriptor associated with it */
 static const struct of_device_id scmi_of_match[] = {
+#ifdef CONFIG_MAILBOX
 	{ .compatible = "arm,scmi", .data = &scmi_mailbox_desc },
+#endif
 #ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
 	{ .compatible = "arm,scmi-smc", .data = &scmi_smc_desc},
 #endif
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 066/108] ARM: dts: aspeed: Everest: Fix cable card PCA chips

[Sasha Levin]

From: Santosh Puranik <santosh.puranik@in.ibm.com>

[ Upstream commit 010da3daf9278ed03d38b7dcb0422f1a7df1bdd3 ]

Correct two PCA chips which were placed on the wrong I2C bus and
address.

Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Santosh Puranik <santosh.puranik@in.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts | 168 +++++++++----------
 1 file changed, 83 insertions(+), 85 deletions(-)

diff --git a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
index 3295c8c7c05c..27af28c8847d 100644
--- a/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-ibm-everest.dts
@@ -353,10 +353,47 @@ gpio@15 {
 
 &i2c1 {
 	status = "okay";
+};
+
+&i2c2 {
+	status = "okay";
+};
 
-	pca2: pca9552@61 {
+&i2c3 {
+	status = "okay";
+
+	eeprom@54 {
+		compatible = "atmel,24c128";
+		reg = <0x54>;
+	};
+
+	power-supply@68 {
+		compatible = "ibm,cffps";
+		reg = <0x68>;
+	};
+
+	power-supply@69 {
+		compatible = "ibm,cffps";
+		reg = <0x69>;
+	};
+
+	power-supply@6a {
+		compatible = "ibm,cffps";
+		reg = <0x6a>;
+	};
+
+	power-supply@6b {
+		compatible = "ibm,cffps";
+		reg = <0x6b>;
+	};
+};
+
+&i2c4 {
+	status = "okay";
+
+	pca2: pca9552@65 {
 		compatible = "nxp,pca9552";
-		reg = <0x61>;
+		reg = <0x65>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -424,12 +461,54 @@ gpio@9 {
 			reg = <9>;
 			type = <PCA955X_TYPE_GPIO>;
 		};
+	};
 
+	i2c-switch@70 {
+		compatible = "nxp,pca9546";
+		reg = <0x70>;
+		#address-cells = <1>;
+		#size-cells = <0>;
+		status = "okay";
+		i2c-mux-idle-disconnect;
+
+		i2c4mux0chn0: i2c@0 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0>;
+			eeprom@52 {
+				compatible = "atmel,24c64";
+				reg = <0x52>;
+			};
+		};
+
+		i2c4mux0chn1: i2c@1 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <1>;
+			eeprom@50 {
+				compatible = "atmel,24c64";
+				reg = <0x50>;
+			};
+		};
+
+		i2c4mux0chn2: i2c@2 {
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <2>;
+			eeprom@51 {
+				compatible = "atmel,24c64";
+				reg = <0x51>;
+			};
+		};
 	};
+};
 
-	pca3: pca9552@62 {
+&i2c5 {
+	status = "okay";
+
+	pca3: pca9552@66 {
 		compatible = "nxp,pca9552";
-		reg = <0x62>;
+		reg = <0x66>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 
@@ -512,87 +591,6 @@ gpio@11 {
 
 	};
 
-};
-
-&i2c2 {
-	status = "okay";
-};
-
-&i2c3 {
-	status = "okay";
-
-	eeprom@54 {
-		compatible = "atmel,24c128";
-		reg = <0x54>;
-	};
-
-	power-supply@68 {
-		compatible = "ibm,cffps";
-		reg = <0x68>;
-	};
-
-	power-supply@69 {
-		compatible = "ibm,cffps";
-		reg = <0x69>;
-	};
-
-	power-supply@6a {
-		compatible = "ibm,cffps";
-		reg = <0x6a>;
-	};
-
-	power-supply@6b {
-		compatible = "ibm,cffps";
-		reg = <0x6b>;
-	};
-};
-
-&i2c4 {
-	status = "okay";
-
-	i2c-switch@70 {
-		compatible = "nxp,pca9546";
-		reg = <0x70>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		status = "okay";
-		i2c-mux-idle-disconnect;
-
-		i2c4mux0chn0: i2c@0 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <0>;
-			eeprom@52 {
-				compatible = "atmel,24c64";
-				reg = <0x52>;
-			};
-		};
-
-		i2c4mux0chn1: i2c@1 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <1>;
-			eeprom@50 {
-				compatible = "atmel,24c64";
-				reg = <0x50>;
-			};
-		};
-
-		i2c4mux0chn2: i2c@2 {
-			#address-cells = <1>;
-			#size-cells = <0>;
-			reg = <2>;
-			eeprom@51 {
-				compatible = "atmel,24c64";
-				reg = <0x51>;
-			};
-		};
-	};
-};
-
-&i2c5 {
-	status = "okay";
-
 	i2c-switch@70 {
 		compatible = "nxp,pca9546";
 		reg = <0x70>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 067/108] ARM: dts: bcm283x: Fix up MMC node names

[Sasha Levin]

From: Stefan Wahren <stefan.wahren@i2se.com>

[ Upstream commit f230c32349eb0a43a012a81c08a7f13859b86cbb ]

Fix the node names for the MMC/SD card controller to conform
to the standard node name mmc@..

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-2-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2711.dtsi | 2 +-
 arch/arm/boot/dts/bcm283x.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index 720beec54d61..d872064db761 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -413,7 +413,7 @@ emmc2bus: emmc2bus {
 		ranges = <0x0 0x7e000000  0x0 0xfe000000  0x01800000>;
 		dma-ranges = <0x0 0xc0000000  0x0 0x00000000  0x40000000>;
 
-		emmc2: emmc2@7e340000 {
+		emmc2: mmc@7e340000 {
 			compatible = "brcm,bcm2711-emmc2";
 			reg = <0x0 0x7e340000 0x100>;
 			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index b83a864e2e8b..0f3be55201a5 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -420,7 +420,7 @@ pwm: pwm@7e20c000 {
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7e300000 {
+		sdhci: mmc@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
 			interrupts = <2 30>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 068/108] ARM: dts: bcm283x: Fix up GPIO LED node names

[Sasha Levin]

From: Stefan Wahren <stefan.wahren@i2se.com>

[ Upstream commit 5f30dacf37bc93308e91e4d0fc94681ca73f0f91 ]

Fix the node names for the GPIO LEDs to conform to the standard node
name led-..

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2711-rpi-4-b.dts      | 4 ++--
 arch/arm/boot/dts/bcm2835-rpi-a-plus.dts   | 4 ++--
 arch/arm/boot/dts/bcm2835-rpi-a.dts        | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-b-plus.dts   | 4 ++--
 arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts   | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-b.dts        | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi     | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-zero-w.dts   | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-zero.dts     | 2 +-
 arch/arm/boot/dts/bcm2835-rpi.dtsi         | 2 +-
 arch/arm/boot/dts/bcm2836-rpi-2-b.dts      | 4 ++--
 arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 4 ++--
 arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 4 ++--
 arch/arm/boot/dts/bcm2837-rpi-3-b.dts      | 2 +-
 arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi     | 2 +-
 15 files changed, 21 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index 3b4ab947492a..27d2f859adfc 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -29,11 +29,11 @@ aliases {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
index 6c8ce39833bf..40b9405f1a8e 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@@ -14,11 +14,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts
index 17fdd48346ff..11edb581dbaf 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts
@@ -14,7 +14,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
index b0355c229cdc..1b435c64bd9c 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@@ -15,11 +15,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 33b3b5c02521..a23c25c00eea 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -15,7 +15,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts
index 2b69957e0113..1b63d6b19750 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -15,7 +15,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
index 58059c2ce129..e4e6b6abbfc1 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
@@ -5,7 +5,7 @@
 
 / {
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
index f65448c01e31..33b2b77aa47d 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
@@ -23,7 +23,7 @@ chosen {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
index 6dd93c6f4966..6f9b3a908f28 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
@@ -18,7 +18,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index d94357b21f7e..87ddcad76083 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -4,7 +4,7 @@ / {
 	leds {
 		compatible = "gpio-leds";
 
-		act {
+		led-act {
 			label = "ACT";
 			default-state = "keep";
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
index 0455a680394a..d8af8eeac7b6 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@@ -15,11 +15,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
index 28be0332c1c8..77099a7871b0 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
@@ -19,11 +19,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
index 37343148643d..61010266ca9a 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -20,11 +20,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index 054ecaa355c9..dd4a48604097 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -20,7 +20,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
index 925cb37c22f0..828a20561b96 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
@@ -14,7 +14,7 @@ leds {
 		 * Since there is no upstream GPIO driver yet,
 		 * remove the incomplete node.
 		 */
-		/delete-node/ act;
+		/delete-node/ led-act;
 	};
 
 	reg_3v3: fixed-regulator {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 070/108] arm64: dts: juno: Update SCPI nodes as per the YAML schema

[Sasha Levin]

From: Sudeep Holla <sudeep.holla@arm.com>

[ Upstream commit 70010556b158a0fefe43415fb0c58347dcce7da0 ]

The SCPI YAML schema expects standard node names for clocks and
power domain controllers. Fix those as per the schema for Juno
platforms.

Link: https://lore.kernel.org/r/20210608145133.2088631-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/arm/juno-base.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi
index 1cc7fdcec51b..8e7a66943b01 100644
--- a/arch/arm64/boot/dts/arm/juno-base.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-base.dtsi
@@ -568,13 +568,13 @@ scpi {
 		clocks {
 			compatible = "arm,scpi-clocks";
 
-			scpi_dvfs: scpi-dvfs {
+			scpi_dvfs: clocks-0 {
 				compatible = "arm,scpi-dvfs-clocks";
 				#clock-cells = <1>;
 				clock-indices = <0>, <1>, <2>;
 				clock-output-names = "atlclk", "aplclk","gpuclk";
 			};
-			scpi_clk: scpi-clk {
+			scpi_clk: clocks-1 {
 				compatible = "arm,scpi-variable-clocks";
 				#clock-cells = <1>;
 				clock-indices = <3>;
@@ -582,7 +582,7 @@ scpi_clk: scpi-clk {
 			};
 		};
 
-		scpi_devpd: scpi-power-domains {
+		scpi_devpd: power-controller {
 			compatible = "arm,scpi-power-domains";
 			num-domains = <2>;
 			#power-domain-cells = <1>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 071/108] ARM: dts: rockchip: fix supply properties in io-domains nodes

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit f07edc41220b14ce057a4e6d7161b30688ddb8a2 ]

A test with rockchip-io-domain.yaml gives notifications
for supply properties in io-domains nodes.
Fix them all into ".*-supply$" format.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210606181632.13371-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3288-rock2-som.dtsi | 2 +-
 arch/arm/boot/dts/rk3288-vyasa.dts      | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
index 44bb5e6f83b1..76363b8afcb9 100644
--- a/arch/arm/boot/dts/rk3288-rock2-som.dtsi
+++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
@@ -218,7 +218,7 @@ &io_domains {
 	flash0-supply = <&vcc_flash>;
 	flash1-supply = <&vccio_pmu>;
 	gpio30-supply = <&vccio_pmu>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
diff --git a/arch/arm/boot/dts/rk3288-vyasa.dts b/arch/arm/boot/dts/rk3288-vyasa.dts
index aa50f8ed4ca0..b156a83eb7d7 100644
--- a/arch/arm/boot/dts/rk3288-vyasa.dts
+++ b/arch/arm/boot/dts/rk3288-vyasa.dts
@@ -379,10 +379,10 @@ &io_domains {
 	audio-supply = <&vcc_18>;
 	bb-supply = <&vcc_io>;
 	dvp-supply = <&vcc_io>;
-	flash0-suuply = <&vcc_18>;
+	flash0-supply = <&vcc_18>;
 	flash1-supply = <&vcc_lan>;
 	gpio30-supply = <&vcc_io>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 072/108] ARM: dts: stm32: fix i2c node name on stm32f746 to prevent warnings

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit ad0ed10ba5792064fc3accbf8f0341152a57eecb ]

Replace upper case by lower case in i2c nodes name.

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f746.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi
index 72c1b76684b6..014b416f57e6 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -360,9 +360,9 @@ i2c2: i2c@40005800 {
 			status = "disabled";
 		};
 
-		i2c3: i2c@40005C00 {
+		i2c3: i2c@40005c00 {
 			compatible = "st,stm32f7-i2c";
-			reg = <0x40005C00 0x400>;
+			reg = <0x40005c00 0x400>;
 			interrupts = <72>,
 				     <73>;
 			resets = <&rcc STM32F7_APB1_RESET(I2C3)>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 073/108] ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit fb1406335c067be074eab38206cf9abfdce2fb0b ]

It fixes the following warning seen running "make dtbs_check W=1"

Warning (simple_bus_reg): /soc/stmmac-axi-config: missing or empty
reg/ranges property

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp151.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi
index fcd3230c469b..23234f950de6 100644
--- a/arch/arm/boot/dts/stm32mp151.dtsi
+++ b/arch/arm/boot/dts/stm32mp151.dtsi
@@ -1416,12 +1416,6 @@ crc1: crc@58009000 {
 			status = "disabled";
 		};
 
-		stmmac_axi_config_0: stmmac-axi-config {
-			snps,wr_osr_lmt = <0x7>;
-			snps,rd_osr_lmt = <0x7>;
-			snps,blen = <0 0 0 0 16 8 4>;
-		};
-
 		ethernet0: ethernet@5800a000 {
 			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
 			reg = <0x5800a000 0x2000>;
@@ -1447,6 +1441,12 @@ ethernet0: ethernet@5800a000 {
 			snps,axi-config = <&stmmac_axi_config_0>;
 			snps,tso;
 			status = "disabled";
+
+			stmmac_axi_config_0: stmmac-axi-config {
+				snps,wr_osr_lmt = <0x7>;
+				snps,rd_osr_lmt = <0x7>;
+				snps,blen = <0 0 0 0 16 8 4>;
+			};
 		};
 
 		usbh_ohci: usb@5800c000 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 074/108] ARM: dts: stm32: fix ltdc pinctrl on microdev2.0-of7

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit 11aaf2a0f8f070e87833775965950157bf57e49a ]

It prevents the following warning:

 pin-controller@50002000: 'ltdc' does not match any of the regexes:
'-[0-9]*$', '^gpio@[0-9a-f]*$', 'pinctrl-[0-9]+'

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts  | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
index 674b2d330dc4..5670b23812a2 100644
--- a/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
+++ b/arch/arm/boot/dts/stm32mp157a-microgea-stm32mp1-microdev2.0-of7.dts
@@ -89,7 +89,7 @@ ltdc_ep0_out: endpoint@0 {
 };
 
 &pinctrl {
-	ltdc_pins: ltdc {
+	ltdc_pins: ltdc-0 {
 		pins {
 			pinmux = <STM32_PINMUX('G', 10, AF14)>,	/* LTDC_B2 */
 				 <STM32_PINMUX('H', 12, AF14)>,	/* LTDC_R6 */
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 075/108] ARM: dts: stm32: fix the Odyssey SoM eMMC VQMMC supply

[Sasha Levin]

From: Grzegorz Szymaszek <gszymaszek@short.pl>

[ Upstream commit f493162319788802b6a49634f7268e691b4c10ec ]

The Seeed SoM-STM32MP157C device tree had the eMMC’s (SDMMC2) VQMMC
supply set to v3v3 (buck4), the same as the VMMC supply. That was
incorrect, as on the SoM, the VQMMC supply is provided from vdd (buck3)
instead.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
index 6cf49a0a9e69..b5601d270c8f 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -269,7 +269,7 @@ &sdmmc2 {
 	st,neg-edge;
 	bus-width = <8>;
 	vmmc-supply = <&v3v3>;
-	vqmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
 	mmc-ddr-3_3v;
 	status = "okay";
 };
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 076/108] ARM: dts: stm32: Drop unused linux, wakeup from touchscreen node on DHCOM SoM

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 5247a50c8b53ca214a488da648e1bb35c35c2597 ]

Fix the following dtbs_check warning:
touchscreen@38: 'linux,wakeup' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index b8c8f0b284c3..c5ea08fec535 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -187,7 +187,6 @@ touchscreen@38 {
 		reg = <0x38>;
 		interrupt-parent = <&gpiog>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
-		linux,wakeup;
 	};
 };
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 077/108] ARM: dts: stm32: Rename eth@N to ethernet@N on DHCOM SoM

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit b586250df24226f8a257e11e1f5953054c54fd35 ]

Fix the following dtbs_check warning:
eth@1,0: $nodename:0: 'eth@1,0' does not match '^ethernet(@.*)?$'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 272a1a67a9ad..ae58f3b4d9d4 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -144,7 +144,7 @@ &fmc {
 	pinctrl-1 = <&fmc_sleep_pins_b>;
 	status = "okay";
 
-	ksz8851: ks8851mll@1,0 {
+	ksz8851: ethernet@1,0 {
 		compatible = "micrel,ks8851-mll";
 		reg = <1 0x0 0x2>, <1 0x2 0x20000>;
 		interrupt-parent = <&gpioc>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 078/108] ARM: dts: stm32: Rename spi-flash/mx66l51235l@N to flash@N on DHCOM SoM

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 9b8a9b389d8464e1ca5a4e92c6a4422844ad4ef3 ]

Fix the following dtbs_check warning:
spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 2 +-
 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index ae58f3b4d9d4..260ef8965e08 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -431,7 +431,7 @@ &qspi {
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
index 013ae369791d..2b0ac605549d 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -198,7 +198,7 @@ &qspi {
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: spi-flash@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 079/108] ARM: dts: stm32: fix stpmic node for stm32mp1 boards

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit 4bf4abe19089245b7b12f35e5cafb5477b3e2c48 ]

On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:

-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157a-stinger96.dtsi   | 7 ++-----
 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 5 +----
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi   | 5 +----
 arch/arm/boot/dts/stm32mp15xx-osd32.dtsi       | 7 ++-----
 4 files changed, 6 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
index 113c48b2ef93..a4b14ef3caee 100644
--- a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
@@ -184,8 +184,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -208,7 +206,6 @@ v1v8: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -219,13 +216,13 @@ bst_out: boost {
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
index b5601d270c8f..2d9461006810 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -173,8 +173,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -197,7 +195,6 @@ v1v2_hdmi: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			 bst_out: boost {
@@ -213,7 +210,7 @@ vbus_otg: pwr_sw1 {
 			 vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			 };
 		};
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 260ef8965e08..3b7fbfac89af 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -327,8 +327,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -350,7 +348,6 @@ v1v8: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -366,7 +363,7 @@ vbus_otg: pwr_sw1 {
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
index 713485a95795..6706d8311a66 100644
--- a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
@@ -146,8 +146,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -171,7 +169,6 @@ v1v2_hdmi: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -182,13 +179,13 @@ bst_out: boost {
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 081/108] ARM: OMAP2+: Block suspend for am3 and am4 if PM is not configured

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 093a474ce10d8ea3db3ef2922aca5a38f34bab1b ]

If the PM related modules are not loaded and PM firmware not configured,
the system suspend fails to resume. Let's fix this by adding initial
platform_suspend_ops to block suspend and warn about missing modules.

When pm33xx and wkup_m3_ipc have been loaded and m3 coprocessor booted
with it's firmware, pm33xx sets up working platform_suspend_ops. Note
that we need to configure at least PM_SUSPEND_STANDBY to have
suspend_set_ops().

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-omap2/pm33xx-core.c | 40 +++++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm/mach-omap2/pm33xx-core.c b/arch/arm/mach-omap2/pm33xx-core.c
index 56f2c0bcae5a..bf0d25fd2cea 100644
--- a/arch/arm/mach-omap2/pm33xx-core.c
+++ b/arch/arm/mach-omap2/pm33xx-core.c
@@ -8,6 +8,7 @@
 
 #include <linux/cpuidle.h>
 #include <linux/platform_data/pm33xx.h>
+#include <linux/suspend.h>
 #include <asm/cpuidle.h>
 #include <asm/smp_scu.h>
 #include <asm/suspend.h>
@@ -324,6 +325,44 @@ static struct am33xx_pm_platform_data *am33xx_pm_get_pdata(void)
 		return NULL;
 }
 
+#ifdef CONFIG_SUSPEND
+/*
+ * Block system suspend initially. Later on pm33xx sets up it's own
+ * platform_suspend_ops after probe. That depends also on loaded
+ * wkup_m3_ipc and booted am335x-pm-firmware.elf.
+ */
+static int amx3_suspend_block(suspend_state_t state)
+{
+	pr_warn("PM not initialized for pm33xx, wkup_m3_ipc, or am335x-pm-firmware.elf\n");
+
+	return -EINVAL;
+}
+
+static int amx3_pm_valid(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+		return 1;
+	default:
+		return 0;
+	}
+}
+
+static const struct platform_suspend_ops amx3_blocked_pm_ops = {
+	.begin = amx3_suspend_block,
+	.valid = amx3_pm_valid,
+};
+
+static void __init amx3_block_suspend(void)
+{
+	suspend_set_ops(&amx3_blocked_pm_ops);
+}
+#else
+static inline void amx3_block_suspend(void)
+{
+}
+#endif	/* CONFIG_SUSPEND */
+
 int __init amx3_common_pm_init(void)
 {
 	struct am33xx_pm_platform_data *pdata;
@@ -337,6 +376,7 @@ int __init amx3_common_pm_init(void)
 	devinfo.size_data = sizeof(*pdata);
 	devinfo.id = -1;
 	platform_device_register_full(&devinfo);
+	amx3_block_suspend();
 
 	return 0;
 }
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 084/108] arm64: dts: rockchip: Update RK3399 PCI host bridge window to 32-bit address memory

[Sasha Levin]

From: Punit Agrawal <punitagrawal@gmail.com>

[ Upstream commit 8efe01b4386ab38a36b99cfdc1dc02c38a8898c3 ]

The PCIe host bridge on RK3399 advertises a single 64-bit memory
address range even though it lies entirely below 4GB.

Previously the OF PCI range parser treated 64-bit ranges more
leniently (i.e., as 32-bit), but since commit 9d57e61bf723 ("of/pci:
Add IORESOURCE_MEM_64 to resource flags for 64-bit memory addresses")
the code takes a stricter view and treats the ranges as advertised in
the device tree (i.e, as 64-bit).

The change in behaviour causes failure when allocating bus addresses
to devices connected behind a PCI-to-PCI bridge that require
non-prefetchable memory ranges. The allocation failure was observed
for certain Samsung NVMe drives connected to RockPro64 boards.

Update the host bridge window attributes to treat it as 32-bit address
memory. This fixes the allocation failure observed since commit
9d57e61bf723.

Reported-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/7a1e2ebc-f7d8-8431-d844-41a9c36a8911@arm.com
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Punit Agrawal <punitagrawal@gmail.com>
Tested-by: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20210607112856.3499682-5-punitagrawal@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 1703817c7354..7f8081f9e30e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -227,7 +227,7 @@ pcie0: pcie@f8000000 {
 		       <&pcie_phy 2>, <&pcie_phy 3>;
 		phy-names = "pcie-phy-0", "pcie-phy-1",
 			    "pcie-phy-2", "pcie-phy-3";
-		ranges = <0x83000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x1e00000>,
+		ranges = <0x82000000 0x0 0xfa000000 0x0 0xfa000000 0x0 0x1e00000>,
 			 <0x81000000 0x0 0xfbe00000 0x0 0xfbe00000 0x0 0x100000>;
 		resets = <&cru SRST_PCIE_CORE>, <&cru SRST_PCIE_MGMT>,
 			 <&cru SRST_PCIE_MGMT_STICKY>, <&cru SRST_PCIE_PIPE>,
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 085/108] arm64: dts: ls208xa: remove bus-num from dspi node

[Sasha Levin]

From: Mian Yousaf Kaukab <ykaukab@suse.de>

[ Upstream commit 8240c972c1798ea013cbb407722295fc826b3584 ]

On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:

[   10.471363] couldn't get idr
[   10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[   10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[   10.471708] fsl-dspi: probe of 2100000.spi failed with error -16

Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c33c ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.

Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index 135ac8210871..801ba9612d36 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -929,7 +929,6 @@ dspi: spi@2100000 {
 					    QORIQ_CLK_PLL_DIV(4)>;
 			clock-names = "dspi";
 			spi-num-chipselects = <5>;
-			bus-num = <0>;
 		};
 
 		esdhc: esdhc@2140000 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 086/108] arm64: dts: imx8mn-beacon-som: Assign PMIC clock

[Sasha Levin]

From: Adam Ford <aford173@gmail.com>

[ Upstream commit 1de3aa8611d21d6be546ca1cd13ee05bdd650018 ]

The PMIC throws an errors because the clock isn't assigned to it.
Fix this by assigning the clocks info.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
index c35eeaff958f..54eaf3d6055b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mn-beacon-som.dtsi
@@ -120,6 +120,9 @@ pmic@4b {
 		interrupt-parent = <&gpio1>;
 		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
+		#clock-cells = <0>;
+		clocks = <&osc_32k 0>;
+		clock-output-names = "clk-32k-out";
 
 		regulators {
 			buck1_reg: BUCK1 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 087/108] arm64: dts: imx8mq: assign PCIe clocks

[Sasha Levin]

From: Lucas Stach <l.stach@pengutronix.de>

[ Upstream commit 15a5261e4d052bf85c7fba24dbe0e9a7c8c05925 ]

This fixes multiple issues with the current non-existent PCIe clock setup:

The controller can run at up to 250MHz, so use a parent that provides this
clock.

The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.

The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 17c449e12c2e..91df9c5350ae 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -1383,6 +1383,14 @@ pcie0: pcie@33800000 {
 			         <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>,
 			         <&src IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF>;
 			reset-names = "pciephy", "apps", "turnoff";
+			assigned-clocks = <&clk IMX8MQ_CLK_PCIE1_CTRL>,
+			                  <&clk IMX8MQ_CLK_PCIE1_PHY>,
+			                  <&clk IMX8MQ_CLK_PCIE1_AUX>;
+			assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>,
+			                         <&clk IMX8MQ_SYS2_PLL_100M>,
+			                         <&clk IMX8MQ_SYS1_PLL_80M>;
+			assigned-clock-rates = <250000000>, <100000000>,
+			                       <10000000>;
 			status = "disabled";
 		};
 
@@ -1413,6 +1421,14 @@ pcie1: pcie@33c00000 {
 			         <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>,
 			         <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF>;
 			reset-names = "pciephy", "apps", "turnoff";
+			assigned-clocks = <&clk IMX8MQ_CLK_PCIE2_CTRL>,
+			                  <&clk IMX8MQ_CLK_PCIE2_PHY>,
+			                  <&clk IMX8MQ_CLK_PCIE2_AUX>;
+			assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>,
+			                         <&clk IMX8MQ_SYS2_PLL_100M>,
+			                         <&clk IMX8MQ_SYS1_PLL_80M>;
+			assigned-clock-rates = <250000000>, <100000000>,
+			                       <10000000>;
 			status = "disabled";
 		};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 088/108] arm64: dts: imx8: conn: fix enet clock setting

[Sasha Levin]

From: Dong Aisheng <aisheng.dong@nxp.com>

[ Upstream commit dfda1fd16aa71c839e4002109b0cd15f61105ebb ]

enet_clk_ref actually is sourced from internal gpr clocks
which needs a default rate. Also update enet lpcg clock
output names to be more straightforward.

Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 .../boot/dts/freescale/imx8-ss-conn.dtsi      | 50 ++++++++++++-------
 1 file changed, 32 insertions(+), 18 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
index e1e81ca0ca69..a79f42a9618e 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-conn.dtsi
@@ -77,9 +77,12 @@ fec1: ethernet@5b040000 {
 			     <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&enet0_lpcg IMX_LPCG_CLK_4>,
 			 <&enet0_lpcg IMX_LPCG_CLK_2>,
-			 <&enet0_lpcg IMX_LPCG_CLK_1>,
+			 <&enet0_lpcg IMX_LPCG_CLK_3>,
 			 <&enet0_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "ahb", "enet_clk_ref", "ptp";
+		assigned-clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_PM_CLK_PER>,
+				  <&clk IMX_SC_R_ENET_0 IMX_SC_C_CLKDIV>;
+		assigned-clock-rates = <250000000>, <125000000>;
 		fsl,num-tx-queues=<3>;
 		fsl,num-rx-queues=<3>;
 		power-domains = <&pd IMX_SC_R_ENET_0>;
@@ -94,9 +97,12 @@ fec2: ethernet@5b050000 {
 				<GIC_SPI 263 IRQ_TYPE_LEVEL_HIGH>;
 		clocks = <&enet1_lpcg IMX_LPCG_CLK_4>,
 			 <&enet1_lpcg IMX_LPCG_CLK_2>,
-			 <&enet1_lpcg IMX_LPCG_CLK_1>,
+			 <&enet1_lpcg IMX_LPCG_CLK_3>,
 			 <&enet1_lpcg IMX_LPCG_CLK_0>;
 		clock-names = "ipg", "ahb", "enet_clk_ref", "ptp";
+		assigned-clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
+				  <&clk IMX_SC_R_ENET_1 IMX_SC_C_CLKDIV>;
+		assigned-clock-rates = <250000000>, <125000000>;
 		fsl,num-tx-queues=<3>;
 		fsl,num-rx-queues=<3>;
 		power-domains = <&pd IMX_SC_R_ENET_1>;
@@ -152,15 +158,19 @@ enet0_lpcg: clock-controller@5b230000 {
 		#clock-cells = <1>;
 		clocks = <&clk IMX_SC_R_ENET_0 IMX_SC_PM_CLK_PER>,
 			 <&clk IMX_SC_R_ENET_0 IMX_SC_PM_CLK_PER>,
-			 <&conn_axi_clk>, <&conn_ipg_clk>, <&conn_ipg_clk>;
+			 <&conn_axi_clk>,
+			 <&clk IMX_SC_R_ENET_0 IMX_SC_C_TXCLK>,
+			 <&conn_ipg_clk>,
+			 <&conn_ipg_clk>;
 		clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
-				<IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>,
-				<IMX_LPCG_CLK_5>;
-		clock-output-names = "enet0_ipg_root_clk",
-				     "enet0_tx_clk",
-				     "enet0_ahb_clk",
-				     "enet0_ipg_clk",
-				     "enet0_ipg_s_clk";
+				<IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_3>,
+				<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>;
+		clock-output-names = "enet0_lpcg_timer_clk",
+				     "enet0_lpcg_txc_sampling_clk",
+				     "enet0_lpcg_ahb_clk",
+				     "enet0_lpcg_rgmii_txc_clk",
+				     "enet0_lpcg_ipg_clk",
+				     "enet0_lpcg_ipg_s_clk";
 		power-domains = <&pd IMX_SC_R_ENET_0>;
 	};
 
@@ -170,15 +180,19 @@ enet1_lpcg: clock-controller@5b240000 {
 		#clock-cells = <1>;
 		clocks = <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
 			 <&clk IMX_SC_R_ENET_1 IMX_SC_PM_CLK_PER>,
-			 <&conn_axi_clk>, <&conn_ipg_clk>, <&conn_ipg_clk>;
+			 <&conn_axi_clk>,
+			 <&clk IMX_SC_R_ENET_1 IMX_SC_C_TXCLK>,
+			 <&conn_ipg_clk>,
+			 <&conn_ipg_clk>;
 		clock-indices = <IMX_LPCG_CLK_0>, <IMX_LPCG_CLK_1>,
-				<IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_4>,
-				<IMX_LPCG_CLK_5>;
-		clock-output-names = "enet1_ipg_root_clk",
-				     "enet1_tx_clk",
-				     "enet1_ahb_clk",
-				     "enet1_ipg_clk",
-				     "enet1_ipg_s_clk";
+				<IMX_LPCG_CLK_2>, <IMX_LPCG_CLK_3>,
+				<IMX_LPCG_CLK_4>, <IMX_LPCG_CLK_5>;
+		clock-output-names = "enet1_lpcg_timer_clk",
+				     "enet1_lpcg_txc_sampling_clk",
+				     "enet1_lpcg_ahb_clk",
+				     "enet1_lpcg_rgmii_txc_clk",
+				     "enet1_lpcg_ipg_clk",
+				     "enet1_lpcg_ipg_s_clk";
 		power-domains = <&pd IMX_SC_R_ENET_1>;
 	};
 };
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 091/108] thermal/drivers/imx_sc: Add missing of_node_put for loop iteration

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

[ Upstream commit 3da97620e8d60da4a7eaae46e03e0a494780642d ]

Early exits from for_each_available_child_of_node() should decrement the
node reference counter.  Reported by Coccinelle:

  drivers/thermal/imx_sc_thermal.c:93:1-33: WARNING:
    Function "for_each_available_child_of_node" should have of_node_put() before return around line 97.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210614192230.19248-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/thermal/imx_sc_thermal.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/thermal/imx_sc_thermal.c b/drivers/thermal/imx_sc_thermal.c
index b01d28eca7ee..8d76dbfde6a9 100644
--- a/drivers/thermal/imx_sc_thermal.c
+++ b/drivers/thermal/imx_sc_thermal.c
@@ -93,6 +93,7 @@ static int imx_sc_thermal_probe(struct platform_device *pdev)
 	for_each_available_child_of_node(np, child) {
 		sensor = devm_kzalloc(&pdev->dev, sizeof(*sensor), GFP_KERNEL);
 		if (!sensor) {
+			of_node_put(child);
 			of_node_put(sensor_np);
 			return -ENOMEM;
 		}
@@ -104,6 +105,7 @@ static int imx_sc_thermal_probe(struct platform_device *pdev)
 			dev_err(&pdev->dev,
 				"failed to get valid sensor resource id: %d\n",
 				ret);
+			of_node_put(child);
 			break;
 		}
 
@@ -114,6 +116,7 @@ static int imx_sc_thermal_probe(struct platform_device *pdev)
 		if (IS_ERR(sensor->tzd)) {
 			dev_err(&pdev->dev, "failed to register thermal zone\n");
 			ret = PTR_ERR(sensor->tzd);
+			of_node_put(child);
 			break;
 		}
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.13 096/108] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme

[Sasha Levin]

From: Konstantin Porotchkin <kostap@marvell.com>

[ Upstream commit e3850467bf8c82de4a052619136839fe8054b774 ]

Eliminate 1MB gap between Linux and filesystem partitions.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts
index 2c2af001619b..9758609541c7 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-db.dts
+++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts
@@ -260,7 +260,7 @@ partition@0 {
 			};
 			partition@200000 {
 				label = "Linux";
-				reg = <0x200000 0xd00000>;
+				reg = <0x200000 0xe00000>;
 			};
 			partition@1000000 {
 				label = "Filesystem";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel