[PATCH AUTOSEL 5.10 03/88] ARM: dts: rockchip: Fix thermal sensor cells o rk322x

[PATCH AUTOSEL 5.10 03/88] ARM: dts: rockchip: Fix thermal sensor cells o rk322x

[Sasha Levin]

From: Ezequiel Garcia <ezequiel@collabora.com>

[ Upstream commit d5c24e20daf09587cbc221d40be1ba92673e8d94 ]

The number of cells to be used with a thermal sensor specifier
must be "1". Fix this.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20210506175514.168365-2-ezequiel@collabora.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk322x.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi
index 48e6e8d44a1a..5fdea760ffd4 100644
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rk322x.dtsi
@@ -524,7 +524,7 @@ tsadc: tsadc@11150000 {
 		pinctrl-0 = <&otp_pin>;
 		pinctrl-1 = <&otp_out>;
 		pinctrl-2 = <&otp_pin>;
-		#thermal-sensor-cells = <0>;
+		#thermal-sensor-cells = <1>;
 		rockchip,hw-tshut-temp = <95000>;
 		status = "disabled";
 	};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 04/88] ARM: dts: rockchip: fix pinctrl sleep nodename for rk3036-kylin and rk3288

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit dfbfb86a43f9a5bbd166d88bca9e07ee4e1bff31 ]

A test with the command below aimed at powerpc generates
notifications in the Rockchip ARM tree.

Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3036-kylin and rk3288

make ARCH=arm dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3036-kylin.dts | 2 +-
 arch/arm/boot/dts/rk3288.dtsi      | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/rk3036-kylin.dts b/arch/arm/boot/dts/rk3036-kylin.dts
index 7154b827ea2f..e817eba8c622 100644
--- a/arch/arm/boot/dts/rk3036-kylin.dts
+++ b/arch/arm/boot/dts/rk3036-kylin.dts
@@ -390,7 +390,7 @@ sdmmc_pwr: sdmmc-pwr {
 		};
 	};
 
-	sleep {
+	suspend {
 		global_pwroff: global-pwroff {
 			rockchip,pins = <2 RK_PA7 1 &pcfg_pull_none>;
 		};
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 68d5a58cfe88..fb2e89aa71c9 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -1593,7 +1593,7 @@ pcfg_pull_none_12ma: pcfg-pull-none-12ma {
 			drive-strength = <12>;
 		};
 
-		sleep {
+		suspend {
 			global_pwroff: global-pwroff {
 				rockchip,pins = <0 RK_PA0 1 &pcfg_pull_none>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 05/88] arm64: dts: rockchip: fix pinctrl sleep nodename for rk3399.dtsi

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit a7ecfad495f8af63a5cb332c91f60ab2018897f5 ]

A test with the command below aimed at powerpc generates
notifications in the Rockchip arm64 tree.

Fix pinctrl "sleep" nodename by renaming it to "suspend"
for rk3399.dtsi

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/powerpc/sleep.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210126110221.10815-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index 7e69603fb41c..ee6287b872db 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -2342,7 +2342,7 @@ sdmmc_wp: sdmmc-wp {
 			};
 		};
 
-		sleep {
+		suspend {
 			ap_pwroff: ap-pwroff {
 				rockchip,pins = <1 RK_PA5 1 &pcfg_pull_none>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 06/88] ARM: dts: rockchip: Fix the timer clocks order

[Sasha Levin]

From: Ezequiel Garcia <ezequiel@collabora.com>

[ Upstream commit 7b46d674ac000b101fdad92cf16cc11d90b72f86 ]

Fixed order is the device-tree convention.
The timer driver currently gets clocks by name,
so no changes are needed there.

Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Link: https://lore.kernel.org/r/20210506111136.3941-3-ezequiel@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3188.dtsi | 8 ++++----
 arch/arm/boot/dts/rk3288.dtsi | 4 ++--
 2 files changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index 2298a8d840ba..2c08ae60e4a1 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -150,16 +150,16 @@ timer3: timer@2000e000 {
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x2000e000 0x20>;
 		interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER3>, <&cru PCLK_TIMER3>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER3>, <&cru SCLK_TIMER3>;
+		clock-names = "pclk", "timer";
 	};
 
 	timer6: timer@200380a0 {
 		compatible = "rockchip,rk3188-timer", "rockchip,rk3288-timer";
 		reg = <0x200380a0 0x20>;
 		interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&cru SCLK_TIMER6>, <&cru PCLK_TIMER0>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER0>, <&cru SCLK_TIMER6>;
+		clock-names = "pclk", "timer";
 	};
 
 	i2s0: i2s@1011a000 {
diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index fb2e89aa71c9..49b196546cdf 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -240,8 +240,8 @@ timer: timer@ff810000 {
 		compatible = "rockchip,rk3288-timer";
 		reg = <0x0 0xff810000 0x0 0x20>;
 		interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
-		clocks = <&xin24m>, <&cru PCLK_TIMER>;
-		clock-names = "timer", "pclk";
+		clocks = <&cru PCLK_TIMER>, <&xin24m>;
+		clock-names = "pclk", "timer";
 	};
 
 	display-subsystem {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 07/88] ARM: dts: rockchip: Fix IOMMU nodes properties on rk322x

[Sasha Levin]

From: Benjamin Gaignard <benjamin.gaignard@collabora.com>

[ Upstream commit 6b023929666f0be5df75f5e0278d1b70effadf42 ]

Add '#" to iommu-cells properties.
Remove useless interrupt-names properties

Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Link: https://lore.kernel.org/r/20210507090232.233049-4-benjamin.gaignard@collabora.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk322x.dtsi | 10 +++-------
 1 file changed, 3 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/rk322x.dtsi b/arch/arm/boot/dts/rk322x.dtsi
index 5fdea760ffd4..7de8b006ca13 100644
--- a/arch/arm/boot/dts/rk322x.dtsi
+++ b/arch/arm/boot/dts/rk322x.dtsi
@@ -565,10 +565,9 @@ vpu_mmu: iommu@20020800 {
 		compatible = "rockchip,iommu";
 		reg = <0x20020800 0x100>;
 		interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vpu_mmu";
 		clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
@@ -576,10 +575,9 @@ vdec_mmu: iommu@20030480 {
 		compatible = "rockchip,iommu";
 		reg = <0x20030480 0x40>, <0x200304c0 0x40>;
 		interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vdec_mmu";
 		clocks = <&cru ACLK_RKVDEC>, <&cru HCLK_RKVDEC>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
@@ -609,7 +607,6 @@ vop_mmu: iommu@20053f00 {
 		compatible = "rockchip,iommu";
 		reg = <0x20053f00 0x100>;
 		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "vop_mmu";
 		clocks = <&cru ACLK_VOP>, <&cru HCLK_VOP>;
 		clock-names = "aclk", "iface";
 		#iommu-cells = <0>;
@@ -630,10 +627,9 @@ iep_mmu: iommu@20070800 {
 		compatible = "rockchip,iommu";
 		reg = <0x20070800 0x100>;
 		interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-		interrupt-names = "iep_mmu";
 		clocks = <&cru ACLK_IEP>, <&cru HCLK_IEP>;
 		clock-names = "aclk", "iface";
-		iommu-cells = <0>;
+		#iommu-cells = <0>;
 		status = "disabled";
 	};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 08/88] ARM: dts: rockchip: Fix power-controller node names for rk3066a

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit f2948781a72f0d8cf2adf31758c357f2f35e6c79 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-2-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3066a.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/rk3066a.dtsi b/arch/arm/boot/dts/rk3066a.dtsi
index 252750c97f97..bbc3bff50856 100644
--- a/arch/arm/boot/dts/rk3066a.dtsi
+++ b/arch/arm/boot/dts/rk3066a.dtsi
@@ -755,7 +755,7 @@ power: power-controller {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pd_vio@RK3066_PD_VIO {
+		power-domain@RK3066_PD_VIO {
 			reg = <RK3066_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -782,7 +782,7 @@ pd_vio@RK3066_PD_VIO {
 				 <&qos_rga>;
 		};
 
-		pd_video@RK3066_PD_VIDEO {
+		power-domain@RK3066_PD_VIDEO {
 			reg = <RK3066_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
@@ -791,7 +791,7 @@ pd_video@RK3066_PD_VIDEO {
 			pm_qos = <&qos_vpu>;
 		};
 
-		pd_gpu@RK3066_PD_GPU {
+		power-domain@RK3066_PD_GPU {
 			reg = <RK3066_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 09/88] ARM: dts: rockchip: Fix power-controller node names for rk3188

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit d3bcbcd396175ac26aa54919c0b31c7d2878fc24 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-3-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3188.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/rk3188.dtsi b/arch/arm/boot/dts/rk3188.dtsi
index 2c08ae60e4a1..b6bde9d12c2b 100644
--- a/arch/arm/boot/dts/rk3188.dtsi
+++ b/arch/arm/boot/dts/rk3188.dtsi
@@ -699,7 +699,7 @@ power: power-controller {
 		#address-cells = <1>;
 		#size-cells = <0>;
 
-		pd_vio@RK3188_PD_VIO {
+		power-domain@RK3188_PD_VIO {
 			reg = <RK3188_PD_VIO>;
 			clocks = <&cru ACLK_LCDC0>,
 				 <&cru ACLK_LCDC1>,
@@ -721,7 +721,7 @@ pd_vio@RK3188_PD_VIO {
 				 <&qos_rga>;
 		};
 
-		pd_video@RK3188_PD_VIDEO {
+		power-domain@RK3188_PD_VIDEO {
 			reg = <RK3188_PD_VIDEO>;
 			clocks = <&cru ACLK_VDPU>,
 				 <&cru ACLK_VEPU>,
@@ -730,7 +730,7 @@ pd_video@RK3188_PD_VIDEO {
 			pm_qos = <&qos_vpu>;
 		};
 
-		pd_gpu@RK3188_PD_GPU {
+		power-domain@RK3188_PD_GPU {
 			reg = <RK3188_PD_GPU>;
 			clocks = <&cru ACLK_GPU>;
 			pm_qos = <&qos_gpu>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 10/88] ARM: dts: rockchip: Fix power-controller node names for rk3288

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit 970cdc53cb1afa73602028c103dbfb6a230080be ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-4-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3288.dtsi | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/rk3288.dtsi b/arch/arm/boot/dts/rk3288.dtsi
index 49b196546cdf..0d89ad274268 100644
--- a/arch/arm/boot/dts/rk3288.dtsi
+++ b/arch/arm/boot/dts/rk3288.dtsi
@@ -788,7 +788,7 @@ power: power-controller {
 			 *	*_HDMI		HDMI
 			 *	*_MIPI_*	MIPI
 			 */
-			pd_vio@RK3288_PD_VIO {
+			power-domain@RK3288_PD_VIO {
 				reg = <RK3288_PD_VIO>;
 				clocks = <&cru ACLK_IEP>,
 					 <&cru ACLK_ISP>,
@@ -830,7 +830,7 @@ pd_vio@RK3288_PD_VIO {
 			 * Note: The following 3 are HEVC(H.265) clocks,
 			 * and on the ACLK_HEVC_NIU (NOC).
 			 */
-			pd_hevc@RK3288_PD_HEVC {
+			power-domain@RK3288_PD_HEVC {
 				reg = <RK3288_PD_HEVC>;
 				clocks = <&cru ACLK_HEVC>,
 					 <&cru SCLK_HEVC_CABAC>,
@@ -844,7 +844,7 @@ pd_hevc@RK3288_PD_HEVC {
 			 * (video endecoder & decoder) clocks that on the
 			 * ACLK_VCODEC_NIU and HCLK_VCODEC_NIU (NOC).
 			 */
-			pd_video@RK3288_PD_VIDEO {
+			power-domain@RK3288_PD_VIDEO {
 				reg = <RK3288_PD_VIDEO>;
 				clocks = <&cru ACLK_VCODEC>,
 					 <&cru HCLK_VCODEC>;
@@ -855,7 +855,7 @@ pd_video@RK3288_PD_VIDEO {
 			 * Note: ACLK_GPU is the GPU clock,
 			 * and on the ACLK_GPU_NIU (NOC).
 			 */
-			pd_gpu@RK3288_PD_GPU {
+			power-domain@RK3288_PD_GPU {
 				reg = <RK3288_PD_GPU>;
 				clocks = <&cru ACLK_GPU>;
 				pm_qos = <&qos_gpu_r>,
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 11/88] arm64: dts: rockchip: Fix power-controller node names for px30

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit d5de0d688ac6e0202674577b05d0726b8a6af401 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-6-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/px30.dtsi | 16 ++++++++--------
 1 file changed, 8 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/px30.dtsi b/arch/arm64/boot/dts/rockchip/px30.dtsi
index 64193292d26c..0d6761074b11 100644
--- a/arch/arm64/boot/dts/rockchip/px30.dtsi
+++ b/arch/arm64/boot/dts/rockchip/px30.dtsi
@@ -244,20 +244,20 @@ power: power-controller {
 			#size-cells = <0>;
 
 			/* These power domains are grouped by VD_LOGIC */
-			pd_usb@PX30_PD_USB {
+			power-domain@PX30_PD_USB {
 				reg = <PX30_PD_USB>;
 				clocks = <&cru HCLK_HOST>,
 					 <&cru HCLK_OTG>,
 					 <&cru SCLK_OTG_ADP>;
 				pm_qos = <&qos_usb_host>, <&qos_usb_otg>;
 			};
-			pd_sdcard@PX30_PD_SDCARD {
+			power-domain@PX30_PD_SDCARD {
 				reg = <PX30_PD_SDCARD>;
 				clocks = <&cru HCLK_SDMMC>,
 					 <&cru SCLK_SDMMC>;
 				pm_qos = <&qos_sdmmc>;
 			};
-			pd_gmac@PX30_PD_GMAC {
+			power-domain@PX30_PD_GMAC {
 				reg = <PX30_PD_GMAC>;
 				clocks = <&cru ACLK_GMAC>,
 					 <&cru PCLK_GMAC>,
@@ -265,7 +265,7 @@ pd_gmac@PX30_PD_GMAC {
 					 <&cru SCLK_GMAC_RX_TX>;
 				pm_qos = <&qos_gmac>;
 			};
-			pd_mmc_nand@PX30_PD_MMC_NAND {
+			power-domain@PX30_PD_MMC_NAND {
 				reg = <PX30_PD_MMC_NAND>;
 				clocks =  <&cru HCLK_NANDC>,
 					  <&cru HCLK_EMMC>,
@@ -278,14 +278,14 @@ pd_mmc_nand@PX30_PD_MMC_NAND {
 				pm_qos = <&qos_emmc>, <&qos_nand>,
 					 <&qos_sdio>, <&qos_sfc>;
 			};
-			pd_vpu@PX30_PD_VPU {
+			power-domain@PX30_PD_VPU {
 				reg = <PX30_PD_VPU>;
 				clocks = <&cru ACLK_VPU>,
 					 <&cru HCLK_VPU>,
 					 <&cru SCLK_CORE_VPU>;
 				pm_qos = <&qos_vpu>, <&qos_vpu_r128>;
 			};
-			pd_vo@PX30_PD_VO {
+			power-domain@PX30_PD_VO {
 				reg = <PX30_PD_VO>;
 				clocks = <&cru ACLK_RGA>,
 					 <&cru ACLK_VOPB>,
@@ -301,7 +301,7 @@ pd_vo@PX30_PD_VO {
 				pm_qos = <&qos_rga_rd>, <&qos_rga_wr>,
 					 <&qos_vop_m0>, <&qos_vop_m1>;
 			};
-			pd_vi@PX30_PD_VI {
+			power-domain@PX30_PD_VI {
 				reg = <PX30_PD_VI>;
 				clocks = <&cru ACLK_CIF>,
 					 <&cru ACLK_ISP>,
@@ -312,7 +312,7 @@ pd_vi@PX30_PD_VI {
 					 <&qos_isp_wr>, <&qos_isp_m1>,
 					 <&qos_vip>;
 			};
-			pd_gpu@PX30_PD_GPU {
+			power-domain@PX30_PD_GPU {
 				reg = <PX30_PD_GPU>;
 				clocks = <&cru SCLK_GPU>;
 				pm_qos = <&qos_gpu>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 12/88] arm64: dts: rockchip: Fix power-controller node names for rk3328

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit 6e6a282b49c6db408d27231e3c709fbdf25e3c1b ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-7-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3328.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index 93c734d8a46c..60479af601f4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -318,13 +318,13 @@ power: power-controller {
 			#address-cells = <1>;
 			#size-cells = <0>;
 
-			pd_hevc@RK3328_PD_HEVC {
+			power-domain@RK3328_PD_HEVC {
 				reg = <RK3328_PD_HEVC>;
 			};
-			pd_video@RK3328_PD_VIDEO {
+			power-domain@RK3328_PD_VIDEO {
 				reg = <RK3328_PD_VIDEO>;
 			};
-			pd_vpu@RK3328_PD_VPU {
+			power-domain@RK3328_PD_VPU {
 				reg = <RK3328_PD_VPU>;
 				clocks = <&cru ACLK_VPU>, <&cru HCLK_VPU>;
 			};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 13/88] arm64: dts: rockchip: Fix power-controller node names for rk3399

[Sasha Levin]

From: Elaine Zhang <zhangqing@rock-chips.com>

[ Upstream commit 148bbe29f9108812c6fedd8a228f9e1ed6b422f7 ]

Use more generic names (as recommended in the device tree specification
or the binding documentation)

Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210417112952.8516-8-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3399.dtsi | 40 ++++++++++++------------
 1 file changed, 20 insertions(+), 20 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399.dtsi b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
index ee6287b872db..4b6065dbba55 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399.dtsi
@@ -1000,26 +1000,26 @@ power: power-controller {
 			#size-cells = <0>;
 
 			/* These power domains are grouped by VD_CENTER */
-			pd_iep@RK3399_PD_IEP {
+			power-domain@RK3399_PD_IEP {
 				reg = <RK3399_PD_IEP>;
 				clocks = <&cru ACLK_IEP>,
 					 <&cru HCLK_IEP>;
 				pm_qos = <&qos_iep>;
 			};
-			pd_rga@RK3399_PD_RGA {
+			power-domain@RK3399_PD_RGA {
 				reg = <RK3399_PD_RGA>;
 				clocks = <&cru ACLK_RGA>,
 					 <&cru HCLK_RGA>;
 				pm_qos = <&qos_rga_r>,
 					 <&qos_rga_w>;
 			};
-			pd_vcodec@RK3399_PD_VCODEC {
+			power-domain@RK3399_PD_VCODEC {
 				reg = <RK3399_PD_VCODEC>;
 				clocks = <&cru ACLK_VCODEC>,
 					 <&cru HCLK_VCODEC>;
 				pm_qos = <&qos_video_m0>;
 			};
-			pd_vdu@RK3399_PD_VDU {
+			power-domain@RK3399_PD_VDU {
 				reg = <RK3399_PD_VDU>;
 				clocks = <&cru ACLK_VDU>,
 					 <&cru HCLK_VDU>;
@@ -1028,94 +1028,94 @@ pd_vdu@RK3399_PD_VDU {
 			};
 
 			/* These power domains are grouped by VD_GPU */
-			pd_gpu@RK3399_PD_GPU {
+			power-domain@RK3399_PD_GPU {
 				reg = <RK3399_PD_GPU>;
 				clocks = <&cru ACLK_GPU>;
 				pm_qos = <&qos_gpu>;
 			};
 
 			/* These power domains are grouped by VD_LOGIC */
-			pd_edp@RK3399_PD_EDP {
+			power-domain@RK3399_PD_EDP {
 				reg = <RK3399_PD_EDP>;
 				clocks = <&cru PCLK_EDP_CTRL>;
 			};
-			pd_emmc@RK3399_PD_EMMC {
+			power-domain@RK3399_PD_EMMC {
 				reg = <RK3399_PD_EMMC>;
 				clocks = <&cru ACLK_EMMC>;
 				pm_qos = <&qos_emmc>;
 			};
-			pd_gmac@RK3399_PD_GMAC {
+			power-domain@RK3399_PD_GMAC {
 				reg = <RK3399_PD_GMAC>;
 				clocks = <&cru ACLK_GMAC>,
 					 <&cru PCLK_GMAC>;
 				pm_qos = <&qos_gmac>;
 			};
-			pd_sd@RK3399_PD_SD {
+			power-domain@RK3399_PD_SD {
 				reg = <RK3399_PD_SD>;
 				clocks = <&cru HCLK_SDMMC>,
 					 <&cru SCLK_SDMMC>;
 				pm_qos = <&qos_sd>;
 			};
-			pd_sdioaudio@RK3399_PD_SDIOAUDIO {
+			power-domain@RK3399_PD_SDIOAUDIO {
 				reg = <RK3399_PD_SDIOAUDIO>;
 				clocks = <&cru HCLK_SDIO>;
 				pm_qos = <&qos_sdioaudio>;
 			};
-			pd_tcpc0@RK3399_PD_TCPD0 {
+			power-domain@RK3399_PD_TCPD0 {
 				reg = <RK3399_PD_TCPD0>;
 				clocks = <&cru SCLK_UPHY0_TCPDCORE>,
 					 <&cru SCLK_UPHY0_TCPDPHY_REF>;
 			};
-			pd_tcpc1@RK3399_PD_TCPD1 {
+			power-domain@RK3399_PD_TCPD1 {
 				reg = <RK3399_PD_TCPD1>;
 				clocks = <&cru SCLK_UPHY1_TCPDCORE>,
 					 <&cru SCLK_UPHY1_TCPDPHY_REF>;
 			};
-			pd_usb3@RK3399_PD_USB3 {
+			power-domain@RK3399_PD_USB3 {
 				reg = <RK3399_PD_USB3>;
 				clocks = <&cru ACLK_USB3>;
 				pm_qos = <&qos_usb_otg0>,
 					 <&qos_usb_otg1>;
 			};
-			pd_vio@RK3399_PD_VIO {
+			power-domain@RK3399_PD_VIO {
 				reg = <RK3399_PD_VIO>;
 				#address-cells = <1>;
 				#size-cells = <0>;
 
-				pd_hdcp@RK3399_PD_HDCP {
+				power-domain@RK3399_PD_HDCP {
 					reg = <RK3399_PD_HDCP>;
 					clocks = <&cru ACLK_HDCP>,
 						 <&cru HCLK_HDCP>,
 						 <&cru PCLK_HDCP>;
 					pm_qos = <&qos_hdcp>;
 				};
-				pd_isp0@RK3399_PD_ISP0 {
+				power-domain@RK3399_PD_ISP0 {
 					reg = <RK3399_PD_ISP0>;
 					clocks = <&cru ACLK_ISP0>,
 						 <&cru HCLK_ISP0>;
 					pm_qos = <&qos_isp0_m0>,
 						 <&qos_isp0_m1>;
 				};
-				pd_isp1@RK3399_PD_ISP1 {
+				power-domain@RK3399_PD_ISP1 {
 					reg = <RK3399_PD_ISP1>;
 					clocks = <&cru ACLK_ISP1>,
 						 <&cru HCLK_ISP1>;
 					pm_qos = <&qos_isp1_m0>,
 						 <&qos_isp1_m1>;
 				};
-				pd_vo@RK3399_PD_VO {
+				power-domain@RK3399_PD_VO {
 					reg = <RK3399_PD_VO>;
 					#address-cells = <1>;
 					#size-cells = <0>;
 
-					pd_vopb@RK3399_PD_VOPB {
+					power-domain@RK3399_PD_VOPB {
 						reg = <RK3399_PD_VOPB>;
 						clocks = <&cru ACLK_VOP0>,
 							 <&cru HCLK_VOP0>;
 						pm_qos = <&qos_vop_big_r>,
 							 <&qos_vop_big_w>;
 					};
-					pd_vopl@RK3399_PD_VOPL {
+					power-domain@RK3399_PD_VOPL {
 						reg = <RK3399_PD_VOPL>;
 						clocks = <&cru ACLK_VOP1>,
 							 <&cru HCLK_VOP1>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 15/88] ARM: brcmstb: dts: fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 9a800ce1aada6e0f56b78e4713f4858c8990c1f7 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm7445-bcm97445svmb.dts | 4 ++--
 arch/arm/boot/dts/bcm7445.dtsi             | 2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts b/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
index 8313b7cad542..f92d2cf85972 100644
--- a/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
+++ b/arch/arm/boot/dts/bcm7445-bcm97445svmb.dts
@@ -14,10 +14,10 @@ memory@0 {
 	};
 };
 
-&nand {
+&nand_controller {
 	status = "okay";
 
-	nandcs@1 {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <1>;
 		nand-ecc-step-size = <512>;
diff --git a/arch/arm/boot/dts/bcm7445.dtsi b/arch/arm/boot/dts/bcm7445.dtsi
index 58f67c9b830b..5ac2042515b8 100644
--- a/arch/arm/boot/dts/bcm7445.dtsi
+++ b/arch/arm/boot/dts/bcm7445.dtsi
@@ -148,7 +148,7 @@ aon-ctrl@410000 {
 			reg-names = "aon-ctrl", "aon-sram";
 		};
 
-		nand: nand@3e2800 {
+		nand_controller: nand-controller@3e2800 {
 			status = "disabled";
 			#address-cells = <1>;
 			#size-cells = <0>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 16/88] ARM: Cygnus: dts: fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit e256b48a3b07ee1ae4bfa60abbf509ba8e386862 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-cygnus.dtsi      | 2 +-
 arch/arm/boot/dts/bcm911360_entphn.dts | 4 ++--
 arch/arm/boot/dts/bcm958300k.dts       | 4 ++--
 arch/arm/boot/dts/bcm958305k.dts       | 4 ++--
 4 files changed, 7 insertions(+), 7 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-cygnus.dtsi b/arch/arm/boot/dts/bcm-cygnus.dtsi
index dacaef2c14ca..ea3dc128b764 100644
--- a/arch/arm/boot/dts/bcm-cygnus.dtsi
+++ b/arch/arm/boot/dts/bcm-cygnus.dtsi
@@ -460,7 +460,7 @@ sdhci1: sdhci@18043000 {
 			status = "disabled";
 		};
 
-		nand: nand@18046000 {
+		nand_controller: nand-controller@18046000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x18046000 0x600>, <0xf8105408 0x600>,
 			      <0x18046f00 0x20>;
diff --git a/arch/arm/boot/dts/bcm911360_entphn.dts b/arch/arm/boot/dts/bcm911360_entphn.dts
index b2d323f4a5ab..a76c74b44bba 100644
--- a/arch/arm/boot/dts/bcm911360_entphn.dts
+++ b/arch/arm/boot/dts/bcm911360_entphn.dts
@@ -82,8 +82,8 @@ &uart3 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958300k.dts b/arch/arm/boot/dts/bcm958300k.dts
index b4a1392bd5a6..dda3e11b711f 100644
--- a/arch/arm/boot/dts/bcm958300k.dts
+++ b/arch/arm/boot/dts/bcm958300k.dts
@@ -60,8 +60,8 @@ &uart3 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958305k.dts b/arch/arm/boot/dts/bcm958305k.dts
index 3378683321d3..ea3c6b88b313 100644
--- a/arch/arm/boot/dts/bcm958305k.dts
+++ b/arch/arm/boot/dts/bcm958305k.dts
@@ -68,8 +68,8 @@ &uart3 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@1 {
+&nand_controller {
+	nand@1 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 17/88] ARM: NSP: dts: fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit 0484594be733d5cdf976f55a2d4e8d887f351b69 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-nsp.dtsi     | 2 +-
 arch/arm/boot/dts/bcm958522er.dts  | 4 ++--
 arch/arm/boot/dts/bcm958525er.dts  | 4 ++--
 arch/arm/boot/dts/bcm958525xmc.dts | 4 ++--
 arch/arm/boot/dts/bcm958622hr.dts  | 4 ++--
 arch/arm/boot/dts/bcm958623hr.dts  | 4 ++--
 arch/arm/boot/dts/bcm958625hr.dts  | 4 ++--
 arch/arm/boot/dts/bcm958625k.dts   | 4 ++--
 arch/arm/boot/dts/bcm988312hr.dts  | 4 ++--
 9 files changed, 17 insertions(+), 17 deletions(-)

diff --git a/arch/arm/boot/dts/bcm-nsp.dtsi b/arch/arm/boot/dts/bcm-nsp.dtsi
index e895f7cb8c9f..605b6d2f4a56 100644
--- a/arch/arm/boot/dts/bcm-nsp.dtsi
+++ b/arch/arm/boot/dts/bcm-nsp.dtsi
@@ -269,7 +269,7 @@ mailbox: mailbox@25c00 {
 			dma-coherent;
 		};
 
-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x026000 0x600>,
 			      <0x11b408 0x600>,
diff --git a/arch/arm/boot/dts/bcm958522er.dts b/arch/arm/boot/dts/bcm958522er.dts
index 7be4c4e628e0..5dd1001255c6 100644
--- a/arch/arm/boot/dts/bcm958522er.dts
+++ b/arch/arm/boot/dts/bcm958522er.dts
@@ -74,8 +74,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958525er.dts b/arch/arm/boot/dts/bcm958525er.dts
index e58ed7e95346..0e624c57b585 100644
--- a/arch/arm/boot/dts/bcm958525er.dts
+++ b/arch/arm/boot/dts/bcm958525er.dts
@@ -74,8 +74,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958525xmc.dts b/arch/arm/boot/dts/bcm958525xmc.dts
index 21f922dc6019..2ac6d61ad297 100644
--- a/arch/arm/boot/dts/bcm958525xmc.dts
+++ b/arch/arm/boot/dts/bcm958525xmc.dts
@@ -90,8 +90,8 @@ rtc@68 {
 	};
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958622hr.dts b/arch/arm/boot/dts/bcm958622hr.dts
index a49c2fd21f4a..e072fa83537a 100644
--- a/arch/arm/boot/dts/bcm958622hr.dts
+++ b/arch/arm/boot/dts/bcm958622hr.dts
@@ -78,8 +78,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958623hr.dts b/arch/arm/boot/dts/bcm958623hr.dts
index dd6dff6452b8..835f4765efbc 100644
--- a/arch/arm/boot/dts/bcm958623hr.dts
+++ b/arch/arm/boot/dts/bcm958623hr.dts
@@ -78,8 +78,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958625hr.dts b/arch/arm/boot/dts/bcm958625hr.dts
index a71371b4065e..57974b8fab86 100644
--- a/arch/arm/boot/dts/bcm958625hr.dts
+++ b/arch/arm/boot/dts/bcm958625hr.dts
@@ -89,8 +89,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm958625k.dts b/arch/arm/boot/dts/bcm958625k.dts
index 7782b61c51a1..45a043ea77ce 100644
--- a/arch/arm/boot/dts/bcm958625k.dts
+++ b/arch/arm/boot/dts/bcm958625k.dts
@@ -68,8 +68,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
diff --git a/arch/arm/boot/dts/bcm988312hr.dts b/arch/arm/boot/dts/bcm988312hr.dts
index edd0f630e025..16b212cc8a2a 100644
--- a/arch/arm/boot/dts/bcm988312hr.dts
+++ b/arch/arm/boot/dts/bcm988312hr.dts
@@ -74,8 +74,8 @@ &ehci0 {
 	status = "okay";
 };
 
-&nand {
-	nandcs@0 {
+&nand_controller {
+	nand@0 {
 		compatible = "brcm,nandcs";
 		reg = <0>;
 		nand-on-flash-bbt;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 19/88] ARM: dts: Hurricane 2: Fix NAND nodes names

[Sasha Levin]

From: Rafał Miłecki <rafal@milecki.pl>

[ Upstream commit a4528d9029e2eda16e4fc9b9da1de1fbec10ab26 ]

This matches nand-controller.yaml requirements.

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm-hr2.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/bcm-hr2.dtsi b/arch/arm/boot/dts/bcm-hr2.dtsi
index e8df458aad39..84cda16f68a2 100644
--- a/arch/arm/boot/dts/bcm-hr2.dtsi
+++ b/arch/arm/boot/dts/bcm-hr2.dtsi
@@ -179,7 +179,7 @@ amac0: ethernet@22000 {
 			status = "disabled";
 		};
 
-		nand: nand@26000 {
+		nand_controller: nand-controller@26000 {
 			compatible = "brcm,nand-iproc", "brcm,brcmnand-v6.1";
 			reg = <0x26000 0x600>,
 			      <0x11b408 0x600>,
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 20/88] ARM: dts: imx25-pinfunc: Fix gpio function name for pads GPIO_[A-F]

[Sasha Levin]

From: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>

[ Upstream commit e0cdd26af8eb9001689a4cde4f72c61c1c4b06be ]

The pinfunc definitions used GPIO_A as function instead of GPIO_1_0 as
done for all the other pins with GPIO functionality. Fix for consistency.

There are no mainline users that needs adaption.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx25-pinfunc.h | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/imx25-pinfunc.h b/arch/arm/boot/dts/imx25-pinfunc.h
index f984b702efc5..908caf810351 100644
--- a/arch/arm/boot/dts/imx25-pinfunc.h
+++ b/arch/arm/boot/dts/imx25-pinfunc.h
@@ -563,15 +563,15 @@
 #define MX25_PAD_DE_B__DE_B			0x1f0 0x3ec 0x000 0x00 0x000
 #define MX25_PAD_DE_B__GPIO_2_20		0x1f0 0x3ec 0x000 0x05 0x000
 
-#define MX25_PAD_GPIO_A__GPIO_A			0x1f4 0x3f0 0x000 0x00 0x000
+#define MX25_PAD_GPIO_A__GPIO_1_0		0x1f4 0x3f0 0x000 0x00 0x000
 #define MX25_PAD_GPIO_A__CAN1_TX		0x1f4 0x3f0 0x000 0x06 0x000
 #define MX25_PAD_GPIO_A__USBOTG_PWR		0x1f4 0x3f0 0x000 0x02 0x000
 
-#define MX25_PAD_GPIO_B__GPIO_B			0x1f8 0x3f4 0x000 0x00 0x000
+#define MX25_PAD_GPIO_B__GPIO_1_1		0x1f8 0x3f4 0x000 0x00 0x000
 #define MX25_PAD_GPIO_B__USBOTG_OC		0x1f8 0x3f4 0x57c 0x02 0x001
 #define MX25_PAD_GPIO_B__CAN1_RX		0x1f8 0x3f4 0x480 0x06 0x001
 
-#define MX25_PAD_GPIO_C__GPIO_C			0x1fc 0x3f8 0x000 0x00 0x000
+#define MX25_PAD_GPIO_C__GPIO_1_2		0x1fc 0x3f8 0x000 0x00 0x000
 #define MX25_PAD_GPIO_C__PWM4_PWMO		0x1fc 0x3f8 0x000 0x01 0x000
 #define MX25_PAD_GPIO_C__I2C2_SCL		0x1fc 0x3f8 0x51c 0x02 0x001
 #define MX25_PAD_GPIO_C__KPP_COL4		0x1fc 0x3f8 0x52c 0x03 0x001
@@ -580,18 +580,18 @@
 #define MX25_PAD_GPIO_C__CAN2_TX		0x1fc 0x3f8 0x000 0x06 0x000
 #define MX25_PAD_GPIO_C__CSPI2_SS2		0x1fc 0x3f8 0x000 0x07 0x000
 
-#define MX25_PAD_GPIO_D__GPIO_D			0x200 0x3fc 0x000 0x00 0x000
+#define MX25_PAD_GPIO_D__GPIO_1_3		0x200 0x3fc 0x000 0x00 0x000
 #define MX25_PAD_GPIO_D__I2C2_SDA		0x200 0x3fc 0x520 0x02 0x001
 #define MX25_PAD_GPIO_D__CAN2_RX		0x200 0x3fc 0x484 0x06 0x001
 #define MX25_PAD_GPIO_D__CSPI3_SS2		0x200 0x3fc 0x4c4 0x07 0x001
 
-#define MX25_PAD_GPIO_E__GPIO_E			0x204 0x400 0x000 0x00 0x000
+#define MX25_PAD_GPIO_E__GPIO_1_4		0x204 0x400 0x000 0x00 0x000
 #define MX25_PAD_GPIO_E__I2C3_CLK		0x204 0x400 0x524 0x01 0x002
 #define MX25_PAD_GPIO_E__LD16			0x204 0x400 0x000 0x02 0x000
 #define MX25_PAD_GPIO_E__AUD7_TXD		0x204 0x400 0x000 0x04 0x000
 #define MX25_PAD_GPIO_E__UART4_RXD		0x204 0x400 0x570 0x06 0x002
 
-#define MX25_PAD_GPIO_F__GPIO_F			0x208 0x404 0x000 0x00 0x000
+#define MX25_PAD_GPIO_F__GPIO_1_5		0x208 0x404 0x000 0x00 0x000
 #define MX25_PAD_GPIO_F__LD17			0x208 0x404 0x000 0x02 0x000
 #define MX25_PAD_GPIO_F__AUD7_TXC		0x208 0x404 0x000 0x04 0x000
 #define MX25_PAD_GPIO_F__UART4_TXD		0x208 0x404 0x000 0x06 0x000
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 21/88] ARM: dts: exynos: align Broadcom WiFi with dtschema

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

[ Upstream commit cc29e39412b9a78b43f7dfa09d739f8ba9fa7984 ]

The Broadcom BCM4329 family dtschema expects devices to be compatible
also with brcm,bcm4329-fmac:

  arch/arm/boot/dts/exynos3250-rinato.dt.yaml: wifi@1: compatible: 'oneOf' conditional failed, one must be fixed:
    ['brcm,bcm4334-fmac'] is too short
    'brcm,bcm4329-fmac' was expected

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210505135941.59898-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/exynos3250-rinato.dts         | 2 +-
 arch/arm/boot/dts/exynos4210-i9100.dts          | 2 +-
 arch/arm/boot/dts/exynos4210-trats.dts          | 2 +-
 arch/arm/boot/dts/exynos4210-universal_c210.dts | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index f9e3b13d3aac..8ef20a66e24e 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -653,7 +653,7 @@ &mshc_1 {
 	mmc-pwrseq = <&wlan_pwrseq>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4334-fmac";
+		compatible = "brcm,bcm4334-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 
 		interrupt-parent = <&gpx1>;
diff --git a/arch/arm/boot/dts/exynos4210-i9100.dts b/arch/arm/boot/dts/exynos4210-i9100.dts
index 7777bf51a6e6..083408f3f695 100644
--- a/arch/arm/boot/dts/exynos4210-i9100.dts
+++ b/arch/arm/boot/dts/exynos4210-i9100.dts
@@ -746,7 +746,7 @@ &sdhci_3 {
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4330-fmac";
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 
 		interrupt-parent = <&gpx2>;
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index a226bec56a45..68635dad541f 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -501,7 +501,7 @@ &sdhci_3 {
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4330-fmac";
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 
 		interrupt-parent = <&gpx2>;
diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts
index 08284e8f3624..28361994ff80 100644
--- a/arch/arm/boot/dts/exynos4210-universal_c210.dts
+++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts
@@ -596,7 +596,7 @@ &sdhci_3 {
 	pinctrl-0 = <&sd3_clk>, <&sd3_cmd>, <&sd3_bus4>;
 
 	brcmf: wifi@1 {
-		compatible = "brcm,bcm4330-fmac";
+		compatible = "brcm,bcm4330-fmac", "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpx2>;
 		interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 22/88] ARM: dts: imx6: phyFLEX: Fix UART hardware flow control

[Sasha Levin]

From: Primoz Fiser <primoz.fiser@norik.com>

[ Upstream commit 14cdc1f243d79e0b46be150502b7dba9c5a6bdfd ]

Serial interface uart3 on phyFLEX board is capable of 5-wire connection
including signals RTS and CTS for hardware flow control.

Fix signals UART3_CTS_B and UART3_RTS_B padmux assignments and add
missing property "uart-has-rtscts" to allow serial interface to be
configured and used with the hardware flow control.

Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi | 5 +++--
 1 file changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
index 5f84e9f2b576..33a70f436aa3 100644
--- a/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-phytec-pfla02.dtsi
@@ -315,8 +315,8 @@ pinctrl_uart3: uart3grp {
 			fsl,pins = <
 				MX6QDL_PAD_EIM_D24__UART3_TX_DATA	0x1b0b1
 				MX6QDL_PAD_EIM_D25__UART3_RX_DATA	0x1b0b1
-				MX6QDL_PAD_EIM_D30__UART3_RTS_B		0x1b0b1
-				MX6QDL_PAD_EIM_D31__UART3_CTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D31__UART3_RTS_B		0x1b0b1
+				MX6QDL_PAD_EIM_D30__UART3_CTS_B		0x1b0b1
 			>;
 		};
 
@@ -403,6 +403,7 @@ &reg_soc {
 &uart3 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_uart3>;
+	uart-has-rtscts;
 	status = "disabled";
 };
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 23/88] ARM: imx: pm-imx5: Fix references to imx5_cpu_suspend_info

[Sasha Levin]

From: Jonathan Neuschäfer <j.neuschaefer@gmx.net>

[ Upstream commit 89b759469d525f4d5f9c29cd3b1f490311c67f85 ]

The name of the struct, as defined in arch/arm/mach-imx/pm-imx5.c,
is imx5_cpu_suspend_info.

Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-imx/suspend-imx53.S | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/mach-imx/suspend-imx53.S b/arch/arm/mach-imx/suspend-imx53.S
index 41b8aad65363..46570ec2fbcf 100644
--- a/arch/arm/mach-imx/suspend-imx53.S
+++ b/arch/arm/mach-imx/suspend-imx53.S
@@ -28,11 +28,11 @@
  *                              ^
  *                              ^
  *                      imx53_suspend code
- *              PM_INFO structure(imx53_suspend_info)
+ *              PM_INFO structure(imx5_cpu_suspend_info)
  * ======================== low address =======================
  */
 
-/* Offsets of members of struct imx53_suspend_info */
+/* Offsets of members of struct imx5_cpu_suspend_info */
 #define SUSPEND_INFO_MX53_M4IF_V_OFFSET		0x0
 #define SUSPEND_INFO_MX53_IOMUXC_V_OFFSET	0x4
 #define SUSPEND_INFO_MX53_IO_COUNT_OFFSET	0x8
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 24/88] arm64: dts: rockchip: fix regulator-gpio states array

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit b82f8e2992534aab0fa762a37376be30df263701 ]

A test with the command below gives this error:

/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dt.yaml:
sdmmcio-regulator: states:0:
[1800000, 1, 3300000, 0] is too long

dtbs_check expects regulator-gpio states in a format
of 2 per item, so fix them all.

make ARCH=arm64 dtbs_check
DT_SCHEMA_FILES=Documentation/devicetree/bindings/
regulator/gpio-regulator.yaml

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210510215840.16270-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts       | 4 ++--
 arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts   | 4 ++--
 arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts       | 4 ++--
 arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi | 2 +-
 arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi         | 4 ++--
 5 files changed, 9 insertions(+), 9 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
index 7a96be10eaf0..bce6f8b7db43 100644
--- a/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3308-roc-cc.dts
@@ -78,8 +78,8 @@ vcc_sdmmc: vcc-sdmmc {
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3300000>;
 		gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x0
-			  3300000 0x1>;
+		states = <1800000 0x0>,
+			 <3300000 0x1>;
 		vin-supply = <&vcc5v0_sys>;
 	};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
index 1eecad724f04..83a0bdbe00d6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-nanopi-r2s.dts
@@ -71,8 +71,8 @@ vcc_io_sdio: sdmmcio-regulator {
 		regulator-settling-time-us = <5000>;
 		regulator-type = "voltage";
 		startup-delay-us = <2000>;
-		states = <1800000 0x1
-			  3300000 0x0>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
 		vin-supply = <&vcc_io_33>;
 	};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
index b76282e704de..daa9a0c601a9 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3328-roc-cc.dts
@@ -45,8 +45,8 @@ vcc_sd: sdmmc-regulator {
 	vcc_sdio: sdmmcio-regulator {
 		compatible = "regulator-gpio";
 		gpios = <&grf_gpio 0 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1
-			  3300000 0x0>;
+		states = <1800000 0x1>,
+			 <3300000 0x0>;
 		regulator-name = "vcc_sdio";
 		regulator-type = "voltage";
 		regulator-min-microvolt = <1800000>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
index 60cd1c18cd4e..e9ecffc409c0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru-scarlet.dtsi
@@ -245,7 +245,7 @@ &ppvar_gpu_pwm {
 };
 
 &ppvar_sd_card_io {
-	states = <1800000 0x0 3300000 0x1>;
+	states = <1800000 0x0>, <3300000 0x1>;
 	regulator-max-microvolt = <3300000>;
 };
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
index 32dcaf210085..765b24a2bcbf 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-gru.dtsi
@@ -247,8 +247,8 @@ ppvar_sd_card_io: ppvar-sd-card-io {
 		enable-active-high;
 		enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
 		gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
-		states = <1800000 0x1
-			  3000000 0x0>;
+		states = <1800000 0x1>,
+			 <3000000 0x0>;
 
 		regulator-min-microvolt = <1800000>;
 		regulator-max-microvolt = <3000000>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 25/88] ARM: dts: ux500: Fix interrupt cells

[Sasha Levin]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

[ Upstream commit e4ff0112a03c2e353c8457cd33c88feb89dfec41 ]

Fix interrupt cells in DT AB8500/AB8505 source files. The
compiled DTB files will stay the same.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ab8500.dtsi | 26 +++++++++++++-------------
 arch/arm/boot/dts/ste-ab8505.dtsi | 22 +++++++++++-----------
 2 files changed, 24 insertions(+), 24 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
index aab5719cc1a9..5fde474ade22 100644
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -42,15 +42,15 @@ ab8500_gpio: ab8500-gpio {
 
 				ab8500-rtc {
 					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};
 
 				gpadc: ab8500-gpadc {
 					compatible = "stericsson,ab8500-gpadc";
-					interrupts = <32 IRQ_TYPE_LEVEL_HIGH
-						      39 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <32 IRQ_TYPE_LEVEL_HIGH>,
+						     <39 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "HW_CONV_END", "SW_CONV_END";
 					vddadc-supply = <&ab8500_ldo_tvout_reg>;
 					#address-cells = <1>;
@@ -169,13 +169,13 @@ ab8500_chargalg {
 
 				ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ID_WAKEUP_R",
 							  "ID_WAKEUP_F",
 							  "VBUS_DET_F",
@@ -192,8 +192,8 @@ ab8500_usb {
 
 				ab8500-ponkey {
 					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
 				};
 
diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi
index 67bc69e67b33..dbaedda2824d 100644
--- a/arch/arm/boot/dts/ste-ab8505.dtsi
+++ b/arch/arm/boot/dts/ste-ab8505.dtsi
@@ -38,8 +38,8 @@ ab8505_gpio: ab8505-gpio {
 
 				ab8500-rtc {
 					compatible = "stericsson,ab8500-rtc";
-					interrupts = <17 IRQ_TYPE_LEVEL_HIGH
-						      18 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <17 IRQ_TYPE_LEVEL_HIGH>,
+						     <18 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "60S", "ALARM";
 				};
 
@@ -131,13 +131,13 @@ ab8500_chargalg {
 
 				ab8500_usb: ab8500_usb {
 					compatible = "stericsson,ab8500-usb";
-					interrupts = < 90 IRQ_TYPE_LEVEL_HIGH
-						       96 IRQ_TYPE_LEVEL_HIGH
-						       14 IRQ_TYPE_LEVEL_HIGH
-						       15 IRQ_TYPE_LEVEL_HIGH
-						       79 IRQ_TYPE_LEVEL_HIGH
-						       74 IRQ_TYPE_LEVEL_HIGH
-						       75 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <90 IRQ_TYPE_LEVEL_HIGH>,
+						     <96 IRQ_TYPE_LEVEL_HIGH>,
+						     <14 IRQ_TYPE_LEVEL_HIGH>,
+						     <15 IRQ_TYPE_LEVEL_HIGH>,
+						     <79 IRQ_TYPE_LEVEL_HIGH>,
+						     <74 IRQ_TYPE_LEVEL_HIGH>,
+						     <75 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ID_WAKEUP_R",
 							  "ID_WAKEUP_F",
 							  "VBUS_DET_F",
@@ -154,8 +154,8 @@ ab8500_usb: ab8500_usb {
 
 				ab8500-ponkey {
 					compatible = "stericsson,ab8500-poweron-key";
-					interrupts = <6 IRQ_TYPE_LEVEL_HIGH
-						      7 IRQ_TYPE_LEVEL_HIGH>;
+					interrupts = <6 IRQ_TYPE_LEVEL_HIGH>,
+						     <7 IRQ_TYPE_LEVEL_HIGH>;
 					interrupt-names = "ONKEY_DBF", "ONKEY_DBR";
 				};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 26/88] ARM: dts: ux500: Rename gpio-controller node

[Sasha Levin]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

[ Upstream commit 4917b702818872fdf2a9973705af3aa7d3d1f19e ]

Rename the AB8500 gpio controller node from ab8500-gpio to
ab8500-gpiocontroller, since -gpio is a common suffix for
gpio consumers.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-ab8500.dtsi      | 2 +-
 arch/arm/boot/dts/ste-ab8505.dtsi      | 2 +-
 arch/arm/boot/dts/ste-href-ab8500.dtsi | 2 +-
 arch/arm/boot/dts/ste-href.dtsi        | 2 +-
 arch/arm/boot/dts/ste-snowball.dts     | 2 +-
 5 files changed, 5 insertions(+), 5 deletions(-)

diff --git a/arch/arm/boot/dts/ste-ab8500.dtsi b/arch/arm/boot/dts/ste-ab8500.dtsi
index 5fde474ade22..16d50369226a 100644
--- a/arch/arm/boot/dts/ste-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-ab8500.dtsi
@@ -34,7 +34,7 @@ ab8500_clock: clock-controller {
 					#clock-cells = <1>;
 				};
 
-				ab8500_gpio: ab8500-gpio {
+				ab8500_gpio: ab8500-gpiocontroller {
 					compatible = "stericsson,ab8500-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/ste-ab8505.dtsi b/arch/arm/boot/dts/ste-ab8505.dtsi
index dbaedda2824d..8d2cda0b4d62 100644
--- a/arch/arm/boot/dts/ste-ab8505.dtsi
+++ b/arch/arm/boot/dts/ste-ab8505.dtsi
@@ -30,7 +30,7 @@ ab8500_clock: clock-controller {
 					#clock-cells = <1>;
 				};
 
-				ab8505_gpio: ab8505-gpio {
+				ab8505_gpio: ab8505-gpiocontroller {
 					compatible = "stericsson,ab8505-gpio";
 					gpio-controller;
 					#gpio-cells = <2>;
diff --git a/arch/arm/boot/dts/ste-href-ab8500.dtsi b/arch/arm/boot/dts/ste-href-ab8500.dtsi
index 4946743de7b9..3ccb7b5c7162 100644
--- a/arch/arm/boot/dts/ste-href-ab8500.dtsi
+++ b/arch/arm/boot/dts/ste-href-ab8500.dtsi
@@ -9,7 +9,7 @@ / {
 	soc {
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 					/* Hog a few default settings */
 					pinctrl-names = "default";
 					pinctrl-0 = <&gpio2_default_mode>,
diff --git a/arch/arm/boot/dts/ste-href.dtsi b/arch/arm/boot/dts/ste-href.dtsi
index ff47cbf6ed3b..81e4f6c2f9dd 100644
--- a/arch/arm/boot/dts/ste-href.dtsi
+++ b/arch/arm/boot/dts/ste-href.dtsi
@@ -217,7 +217,7 @@ msp3: msp@80125000 {
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 				};
 
 				ab8500_usb {
diff --git a/arch/arm/boot/dts/ste-snowball.dts b/arch/arm/boot/dts/ste-snowball.dts
index 27d8a07718a0..f6e0d71f6c09 100644
--- a/arch/arm/boot/dts/ste-snowball.dts
+++ b/arch/arm/boot/dts/ste-snowball.dts
@@ -376,7 +376,7 @@ spi@80002000 {
 
 		prcmu@80157000 {
 			ab8500 {
-				ab8500-gpio {
+				ab8500-gpiocontroller {
 					/*
 					 * AB8500 GPIOs are numbered starting from 1, so the first
 					 * index 0 is what in the datasheet is called "GPIO1", and
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 27/88] ARM: dts: ux500: Fix orientation of accelerometer

[Sasha Levin]

From: Linus Walleij <linus.walleij@linaro.org>

[ Upstream commit 4beba4011995a2c44ee27e1d358dc32e6b9211b3 ]

This adds a mounting matrix to the accelerometer
on the TVK1281618 R3.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
index c0de1337bdaa..457bddabc32c 100644
--- a/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
+++ b/arch/arm/boot/dts/ste-href-tvk1281618-r3.dtsi
@@ -19,6 +19,9 @@ accelerometer@19 {
 					     <19 IRQ_TYPE_EDGE_RISING>;
 				pinctrl-names = "default";
 				pinctrl-0 = <&accel_tvk_mode>;
+				mount-matrix = "0", "-1", "0",
+					       "-1", "0", "0",
+					       "0", "0", "-1";
 			};
 			magnetometer@1e {
 				compatible = "st,lsm303dlm-magn";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 28/88] ARM: dts: imx6dl-riotboard: configure PHY clock and set proper EEE value

[Sasha Levin]

From: Oleksij Rempel <o.rempel@pengutronix.de>

[ Upstream commit 723de6a4126b2474a8106e943749e1554012dad6 ]

Without SoC specific PHY fixups the network interface on this board will
fail to work. Provide missing DT properties to make it work again.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/imx6dl-riotboard.dts | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm/boot/dts/imx6dl-riotboard.dts b/arch/arm/boot/dts/imx6dl-riotboard.dts
index 065d3ab0f50a..e7d9bfbfd0e4 100644
--- a/arch/arm/boot/dts/imx6dl-riotboard.dts
+++ b/arch/arm/boot/dts/imx6dl-riotboard.dts
@@ -106,6 +106,8 @@ rgmii_phy: ethernet-phy@4 {
 			reset-gpios = <&gpio3 31 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <10000>;
 			reset-deassert-us = <1000>;
+			qca,smarteee-tw-us-1g = <24>;
+			qca,clk-out-frequency = <125000000>;
 		};
 	};
 };
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 42/88] arm64: dts: ti: k3-am654x/j721e/j7200-common-proc-board: Fix MCU_RGMII1_TXC direction

[Sasha Levin]

From: Grygorii Strashko <grygorii.strashko@ti.com>

[ Upstream commit 69db725cdb2b803af67897a08ea54467d11f6020 ]

The MCU RGMII MCU_RGMII1_TXC pin is defined as input by mistake, although
this does not make any difference functionality wise it's better to update
to avoid confusion.

Hence fix MCU RGMII MCU_RGMII1_TXC pin pinmux definitions to be an output
in K3 am654x/j721e/j7200 board files.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Link: https://lore.kernel.org/r/20210526132041.6104-1-grygorii.strashko@ti.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts        | 2 +-
 arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts | 2 +-
 arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index d12dd89f3405..937dd7280c7a 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -111,7 +111,7 @@ AM65X_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* (L2) MCU_RGMII1_RD3 */
 			AM65X_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* (L5) MCU_RGMII1_RD2 */
 			AM65X_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* (M6) MCU_RGMII1_RD1 */
 			AM65X_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* (L6) MCU_RGMII1_RD0 */
-			AM65X_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* (N1) MCU_RGMII1_TXC */
+			AM65X_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* (N1) MCU_RGMII1_TXC */
 			AM65X_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* (M1) MCU_RGMII1_RXC */
 		>;
 	};
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
index ef03e7636b66..e8a4143e1c24 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
@@ -29,7 +29,7 @@ J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
 			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
 			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
 			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
 			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
diff --git a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
index 52e121155563..3876942dd66c 100644
--- a/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-j721e-common-proc-board.dts
@@ -206,7 +206,7 @@ J721E_WKUP_IOPAD(0x0078, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
 			J721E_WKUP_IOPAD(0x007c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
 			J721E_WKUP_IOPAD(0x0080, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
 			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
-			J721E_WKUP_IOPAD(0x0070, PIN_INPUT, 0) /* MCU_RGMII1_TXC */
+			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
 			J721E_WKUP_IOPAD(0x0074, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
 		>;
 	};
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 47/88] ARM: dts: stm32: Remove extra size-cells on dhcom-pdk2

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 28b9a4679d8074512f12967497c161b992eb3b75 ]

Fix make dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: gpio-keys-polled: '#address-cells' is a dependency of '#size-cells'
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml: gpio-keys: '#address-cells' is a dependency of '#size-cells'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org

Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index 8456f172d4b1..180a0187a956 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -34,7 +34,6 @@ display_bl: display-bl {
 
 	gpio-keys-polled {
 		compatible = "gpio-keys-polled";
-		#size-cells = <0>;
 		poll-interval = <20>;
 
 		/*
@@ -60,7 +59,6 @@ button-2 {
 
 	gpio-keys {
 		compatible = "gpio-keys";
-		#size-cells = <0>;
 
 		button-1 {
 			label = "TA2-GPIO-B";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 48/88] ARM: dts: stm32: Fix touchscreen node on dhcom-pdk2

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 4b5fadef3fc2ab8863ffdf31eed6a745b1bf6e61 ]

Fix make dtbs_check warning:
arch/arm/boot/dts/stm32mp157c-dhcom-pdk2.dt.yaml:0:0: /soc/i2c@40015000/polytouch@38: failed to match any schema with compatible: ['edt,edt-ft5x06']

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index 180a0187a956..a2d903c0d57f 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -182,8 +182,8 @@ sgtl5000_rx_endpoint: endpoint@1 {
 
 	};
 
-	polytouch@38 {
-		compatible = "edt,edt-ft5x06";
+	touchscreen@38 {
+		compatible = "edt,edt-ft5406";
 		reg = <0x38>;
 		interrupt-parent = <&gpiog>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 49/88] ARM: dts: stm32: fix stm32mp157c-odyssey card detect pin

[Sasha Levin]

From: Grzegorz Szymaszek <gszymaszek@short.pl>

[ Upstream commit 0171b07373cc8c2815ca5fa79a7308fdefa54ca4 ]

The microSD card detect pin is physically connected to the MPU pin PI3.
The Device Tree configuration of the card detect pin was wrong—it was
set to pin PB7 instead. If such configuration was used, the kernel would
hang on “Waiting for root device” when booting from a microSD card.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157c-odyssey.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey.dts b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
index a7ffec8f1516..be1dd5e9e744 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey.dts
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey.dts
@@ -64,7 +64,7 @@ &sdmmc1 {
 	pinctrl-0 = <&sdmmc1_b4_pins_a>;
 	pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
 	pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
-	cd-gpios = <&gpiob 7 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
+	cd-gpios = <&gpioi 3 (GPIO_ACTIVE_LOW | GPIO_PULL_UP)>;
 	disable-wp;
 	st,neg-edge;
 	bus-width = <4>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 50/88] ARM: dts: stm32: fix gpio-keys node on STM32 MCU boards

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit bf24b91f4baf7e421c770a1d9c7d381b10206ac9 ]

Fix following warning observed with "make dtbs_check W=1" command.
It concerns f429 eval and disco boards, f769 disco board.

Warning (unit_address_vs_reg): /gpio_keys/button@0: node has a unit name,
but no reg or ranges property

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32429i-eval.dts  | 8 +++-----
 arch/arm/boot/dts/stm32746g-eval.dts  | 6 ++----
 arch/arm/boot/dts/stm32f429-disco.dts | 6 ++----
 arch/arm/boot/dts/stm32f469-disco.dts | 6 ++----
 arch/arm/boot/dts/stm32f769-disco.dts | 6 ++----
 5 files changed, 11 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/stm32429i-eval.dts b/arch/arm/boot/dts/stm32429i-eval.dts
index 67e7648de41e..8b0ead46ef9b 100644
--- a/arch/arm/boot/dts/stm32429i-eval.dts
+++ b/arch/arm/boot/dts/stm32429i-eval.dts
@@ -119,17 +119,15 @@ led-blue {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 0>;
 		};
-		button@1 {
+		button-1 {
 			label = "Tamper";
 			linux,code = <KEY_RESTART>;
 			gpios = <&gpioc 13 0>;
diff --git a/arch/arm/boot/dts/stm32746g-eval.dts b/arch/arm/boot/dts/stm32746g-eval.dts
index ca8c192449ee..327613fd9666 100644
--- a/arch/arm/boot/dts/stm32746g-eval.dts
+++ b/arch/arm/boot/dts/stm32746g-eval.dts
@@ -81,12 +81,10 @@ led-blue {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "Wake up";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioc 13 0>;
diff --git a/arch/arm/boot/dts/stm32f429-disco.dts b/arch/arm/boot/dts/stm32f429-disco.dts
index 3dc068b91ca1..075ac57d0bf4 100644
--- a/arch/arm/boot/dts/stm32f429-disco.dts
+++ b/arch/arm/boot/dts/stm32f429-disco.dts
@@ -81,12 +81,10 @@ led-green {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 0>;
diff --git a/arch/arm/boot/dts/stm32f469-disco.dts b/arch/arm/boot/dts/stm32f469-disco.dts
index 2e1b3bbbe4b5..8c982ae79f43 100644
--- a/arch/arm/boot/dts/stm32f469-disco.dts
+++ b/arch/arm/boot/dts/stm32f469-disco.dts
@@ -104,12 +104,10 @@ led-blue {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_WAKEUP>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
diff --git a/arch/arm/boot/dts/stm32f769-disco.dts b/arch/arm/boot/dts/stm32f769-disco.dts
index 0ce7fbc20fa4..be943b701980 100644
--- a/arch/arm/boot/dts/stm32f769-disco.dts
+++ b/arch/arm/boot/dts/stm32f769-disco.dts
@@ -75,12 +75,10 @@ led-red {
 		};
 	};
 
-	gpio_keys {
+	gpio-keys {
 		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
 		autorepeat;
-		button@0 {
+		button-0 {
 			label = "User";
 			linux,code = <KEY_HOME>;
 			gpios = <&gpioa 0 GPIO_ACTIVE_HIGH>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 51/88] ARM: dts: stm32: fix RCC node name on stm32f429 MCU

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit e4b948415a89a219d13e454011cdcf9e63ecc529 ]

This prevent warning observed with "make dtbs_check W=1"

Warning (simple_bus_reg): /soc/rcc@40023810: simple-bus unit address format
error, expected "40023800"

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f429.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index ad715a0e1c9a..9adccd4209fb 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -709,7 +709,7 @@ crc: crc@40023000 {
 			status = "disabled";
 		};
 
-		rcc: rcc@40023810 {
+		rcc: rcc@40023800 {
 			#reset-cells = <1>;
 			#clock-cells = <2>;
 			compatible = "st,stm32f42xx-rcc", "st,stm32-rcc";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 52/88] ARM: dts: stm32: fix timer nodes on STM32 MCU to prevent warnings

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit 2388f14d8747f8304e26ee870790e188c9431efd ]

Prevent warning seen with "make dtbs_check W=1" command:

Warning (avoid_unnecessary_addr_size): /soc/timers@40001c00: unnecessary
address-cells/size-cells without "ranges" or child "reg" property

Reviewed-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f429.dtsi | 8 --------
 arch/arm/boot/dts/stm32f746.dtsi | 8 --------
 arch/arm/boot/dts/stm32h743.dtsi | 4 ----
 3 files changed, 20 deletions(-)

diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
index 9adccd4209fb..0dc5fa94dbdf 100644
--- a/arch/arm/boot/dts/stm32f429.dtsi
+++ b/arch/arm/boot/dts/stm32f429.dtsi
@@ -283,8 +283,6 @@ timer@11 {
 		};
 
 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM13)>;
@@ -299,8 +297,6 @@ pwm {
 		};
 
 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F4_APB1_CLOCK(TIM14)>;
@@ -633,8 +629,6 @@ timer@8 {
 		};
 
 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM10)>;
@@ -649,8 +643,6 @@ pwm {
 		};
 
 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F4_APB2_CLOCK(TIM11)>;
diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi
index 640ff54ed00c..81a6fe653e66 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -265,8 +265,6 @@ timer@11 {
 		};
 
 		timers13: timers@40001c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40001C00 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM13)>;
@@ -281,8 +279,6 @@ pwm {
 		};
 
 		timers14: timers@40002000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40002000 0x400>;
 			clocks = <&rcc 0 STM32F7_APB1_CLOCK(TIM14)>;
@@ -531,8 +527,6 @@ timer@8 {
 		};
 
 		timers10: timers@40014400 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014400 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM10)>;
@@ -547,8 +541,6 @@ pwm {
 		};
 
 		timers11: timers@40014800 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-timers";
 			reg = <0x40014800 0x400>;
 			clocks = <&rcc 0 STM32F7_APB2_CLOCK(TIM11)>;
diff --git a/arch/arm/boot/dts/stm32h743.dtsi b/arch/arm/boot/dts/stm32h743.dtsi
index 7febe19e780d..1579707ea566 100644
--- a/arch/arm/boot/dts/stm32h743.dtsi
+++ b/arch/arm/boot/dts/stm32h743.dtsi
@@ -454,8 +454,6 @@ trigger@2 {
 		};
 
 		lptimer4: timer@58002c00 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58002c00 0x400>;
 			clocks = <&rcc LPTIM4_CK>;
@@ -470,8 +468,6 @@ pwm {
 		};
 
 		lptimer5: timer@58003000 {
-			#address-cells = <1>;
-			#size-cells = <0>;
 			compatible = "st,stm32-lptimer";
 			reg = <0x58003000 0x400>;
 			clocks = <&rcc LPTIM5_CK>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 54/88] firmware: arm_scmi: Add SMCCC discovery dependency in Kconfig

[Sasha Levin]

From: Etienne Carriere <etienne.carriere@linaro.org>

[ Upstream commit c05b07963e965ae34e75ee8c33af1095350cd87e ]

ARM_SCMI_PROTOCOL depends on either MAILBOX or HAVE_ARM_SMCCC_DISCOVERY,
not MAILBOX alone. Fix the depedency in Kconfig file and driver to
reflect the same.

Link: https://lore.kernel.org/r/20210521134055.24271-1-etienne.carriere@linaro.org
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
[sudeep.holla: Minor tweaks to subject and change log]
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/Kconfig           | 2 +-
 drivers/firmware/arm_scmi/common.h | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/firmware/Kconfig b/drivers/firmware/Kconfig
index 5fa6b3ca0a38..c08968c5ddf8 100644
--- a/drivers/firmware/Kconfig
+++ b/drivers/firmware/Kconfig
@@ -9,7 +9,7 @@ menu "Firmware Drivers"
 config ARM_SCMI_PROTOCOL
 	tristate "ARM System Control and Management Interface (SCMI) Message Protocol"
 	depends on ARM || ARM64 || COMPILE_TEST
-	depends on MAILBOX
+	depends on MAILBOX || HAVE_ARM_SMCCC_DISCOVERY
 	help
 	  ARM System Control and Management Interface (SCMI) protocol is a
 	  set of operating system-independent software interfaces that are
diff --git a/drivers/firmware/arm_scmi/common.h b/drivers/firmware/arm_scmi/common.h
index 65063fa948d4..34b7ae7980a3 100644
--- a/drivers/firmware/arm_scmi/common.h
+++ b/drivers/firmware/arm_scmi/common.h
@@ -243,7 +243,7 @@ struct scmi_desc {
 };
 
 extern const struct scmi_desc scmi_mailbox_desc;
-#ifdef CONFIG_HAVE_ARM_SMCCC
+#ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
 extern const struct scmi_desc scmi_smc_desc;
 #endif
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 55/88] firmware: arm_scmi: Fix the build when CONFIG_MAILBOX is not selected

[Sasha Levin]

From: Sudeep Holla <sudeep.holla@arm.com>

[ Upstream commit ab7766b72855e6a68109b915d071181b93086e29 ]

0day CI kernel test robot reported following build error with randconfig

aarch64-linux-ld: drivers/firmware/arm_scmi/driver.o:(.rodata+0x1e0):
		undefined reference to `scmi_mailbox_desc'

Fix the error by adding CONFIG_MAILBOX dependency for scmi_mailbox_desc.

Link: https://lore.kernel.org/r/20210603072631.1660963-1-sudeep.holla@arm.com
Cc: Etienne Carriere <etienne.carriere@linaro.org>
Cc: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/arm_scmi/driver.c | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/drivers/firmware/arm_scmi/driver.c b/drivers/firmware/arm_scmi/driver.c
index 6b2ce3f28f7b..7efbf66f117b 100644
--- a/drivers/firmware/arm_scmi/driver.c
+++ b/drivers/firmware/arm_scmi/driver.c
@@ -918,7 +918,9 @@ ATTRIBUTE_GROUPS(versions);
 
 /* Each compatible listed below must have descriptor associated with it */
 static const struct of_device_id scmi_of_match[] = {
+#ifdef CONFIG_MAILBOX
 	{ .compatible = "arm,scmi", .data = &scmi_mailbox_desc },
+#endif
 #ifdef CONFIG_HAVE_ARM_SMCCC_DISCOVERY
 	{ .compatible = "arm,scmi-smc", .data = &scmi_smc_desc},
 #endif
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 56/88] ARM: dts: bcm283x: Fix up MMC node names

[Sasha Levin]

From: Stefan Wahren <stefan.wahren@i2se.com>

[ Upstream commit f230c32349eb0a43a012a81c08a7f13859b86cbb ]

Fix the node names for the MMC/SD card controller to conform
to the standard node name mmc@..

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-2-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2711.dtsi | 2 +-
 arch/arm/boot/dts/bcm283x.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2711.dtsi b/arch/arm/boot/dts/bcm2711.dtsi
index 4847dd305317..3d040f6e2a20 100644
--- a/arch/arm/boot/dts/bcm2711.dtsi
+++ b/arch/arm/boot/dts/bcm2711.dtsi
@@ -395,7 +395,7 @@ emmc2bus: emmc2bus {
 		ranges = <0x0 0x7e000000  0x0 0xfe000000  0x01800000>;
 		dma-ranges = <0x0 0xc0000000  0x0 0x00000000  0x40000000>;
 
-		emmc2: emmc2@7e340000 {
+		emmc2: mmc@7e340000 {
 			compatible = "brcm,bcm2711-emmc2";
 			reg = <0x0 0x7e340000 0x100>;
 			interrupts = <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>;
diff --git a/arch/arm/boot/dts/bcm283x.dtsi b/arch/arm/boot/dts/bcm283x.dtsi
index b83a864e2e8b..0f3be55201a5 100644
--- a/arch/arm/boot/dts/bcm283x.dtsi
+++ b/arch/arm/boot/dts/bcm283x.dtsi
@@ -420,7 +420,7 @@ pwm: pwm@7e20c000 {
 			status = "disabled";
 		};
 
-		sdhci: sdhci@7e300000 {
+		sdhci: mmc@7e300000 {
 			compatible = "brcm,bcm2835-sdhci";
 			reg = <0x7e300000 0x100>;
 			interrupts = <2 30>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 57/88] ARM: dts: bcm283x: Fix up GPIO LED node names

[Sasha Levin]

From: Stefan Wahren <stefan.wahren@i2se.com>

[ Upstream commit 5f30dacf37bc93308e91e4d0fc94681ca73f0f91 ]

Fix the node names for the GPIO LEDs to conform to the standard node
name led-..

Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Link: https://lore.kernel.org/r/1622981777-5023-6-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/bcm2711-rpi-4-b.dts      | 4 ++--
 arch/arm/boot/dts/bcm2835-rpi-a-plus.dts   | 4 ++--
 arch/arm/boot/dts/bcm2835-rpi-a.dts        | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-b-plus.dts   | 4 ++--
 arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts   | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-b.dts        | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi     | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-zero-w.dts   | 2 +-
 arch/arm/boot/dts/bcm2835-rpi-zero.dts     | 2 +-
 arch/arm/boot/dts/bcm2835-rpi.dtsi         | 2 +-
 arch/arm/boot/dts/bcm2836-rpi-2-b.dts      | 4 ++--
 arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts | 4 ++--
 arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts | 4 ++--
 arch/arm/boot/dts/bcm2837-rpi-3-b.dts      | 2 +-
 arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi     | 2 +-
 15 files changed, 21 insertions(+), 21 deletions(-)

diff --git a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
index 09a1182c2936..5395e8c2484e 100644
--- a/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
+++ b/arch/arm/boot/dts/bcm2711-rpi-4-b.dts
@@ -28,11 +28,11 @@ aliases {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 42 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
index 6c8ce39833bf..40b9405f1a8e 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a-plus.dts
@@ -14,11 +14,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2835-rpi-a.dts b/arch/arm/boot/dts/bcm2835-rpi-a.dts
index 17fdd48346ff..11edb581dbaf 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-a.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-a.dts
@@ -14,7 +14,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
index b0355c229cdc..1b435c64bd9c 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-plus.dts
@@ -15,11 +15,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
index 33b3b5c02521..a23c25c00eea 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b-rev2.dts
@@ -15,7 +15,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-b.dts b/arch/arm/boot/dts/bcm2835-rpi-b.dts
index 2b69957e0113..1b63d6b19750 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-b.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-b.dts
@@ -15,7 +15,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
index 58059c2ce129..e4e6b6abbfc1 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi-cm1.dtsi
@@ -5,7 +5,7 @@
 
 / {
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
index f65448c01e31..33b2b77aa47d 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero-w.dts
@@ -23,7 +23,7 @@ chosen {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_LOW>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi-zero.dts b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
index 6dd93c6f4966..6f9b3a908f28 100644
--- a/arch/arm/boot/dts/bcm2835-rpi-zero.dts
+++ b/arch/arm/boot/dts/bcm2835-rpi-zero.dts
@@ -18,7 +18,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2835-rpi.dtsi b/arch/arm/boot/dts/bcm2835-rpi.dtsi
index d94357b21f7e..87ddcad76083 100644
--- a/arch/arm/boot/dts/bcm2835-rpi.dtsi
+++ b/arch/arm/boot/dts/bcm2835-rpi.dtsi
@@ -4,7 +4,7 @@ / {
 	leds {
 		compatible = "gpio-leds";
 
-		act {
+		led-act {
 			label = "ACT";
 			default-state = "keep";
 			linux,default-trigger = "heartbeat";
diff --git a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
index 0455a680394a..d8af8eeac7b6 100644
--- a/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
+++ b/arch/arm/boot/dts/bcm2836-rpi-2-b.dts
@@ -15,11 +15,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&gpio 35 GPIO_ACTIVE_HIGH>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
index 28be0332c1c8..77099a7871b0 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-a-plus.dts
@@ -19,11 +19,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
index 37343148643d..61010266ca9a 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b-plus.dts
@@ -20,11 +20,11 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&gpio 29 GPIO_ACTIVE_HIGH>;
 		};
 
-		pwr {
+		led-pwr {
 			label = "PWR";
 			gpios = <&expgpio 2 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
diff --git a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
index 054ecaa355c9..dd4a48604097 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
+++ b/arch/arm/boot/dts/bcm2837-rpi-3-b.dts
@@ -20,7 +20,7 @@ memory@0 {
 	};
 
 	leds {
-		act {
+		led-act {
 			gpios = <&expgpio 2 GPIO_ACTIVE_HIGH>;
 		};
 	};
diff --git a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
index 925cb37c22f0..828a20561b96 100644
--- a/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
+++ b/arch/arm/boot/dts/bcm2837-rpi-cm3.dtsi
@@ -14,7 +14,7 @@ leds {
 		 * Since there is no upstream GPIO driver yet,
 		 * remove the incomplete node.
 		 */
-		/delete-node/ act;
+		/delete-node/ led-act;
 	};
 
 	reg_3v3: fixed-regulator {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 58/88] arm64: dts: juno: Update SCPI nodes as per the YAML schema

[Sasha Levin]

From: Sudeep Holla <sudeep.holla@arm.com>

[ Upstream commit 70010556b158a0fefe43415fb0c58347dcce7da0 ]

The SCPI YAML schema expects standard node names for clocks and
power domain controllers. Fix those as per the schema for Juno
platforms.

Link: https://lore.kernel.org/r/20210608145133.2088631-1-sudeep.holla@arm.com
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/arm/juno-base.dtsi | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/arm/juno-base.dtsi b/arch/arm64/boot/dts/arm/juno-base.dtsi
index f6c55877fbd9..2c0161125ece 100644
--- a/arch/arm64/boot/dts/arm/juno-base.dtsi
+++ b/arch/arm64/boot/dts/arm/juno-base.dtsi
@@ -564,13 +564,13 @@ scpi {
 		clocks {
 			compatible = "arm,scpi-clocks";
 
-			scpi_dvfs: scpi-dvfs {
+			scpi_dvfs: clocks-0 {
 				compatible = "arm,scpi-dvfs-clocks";
 				#clock-cells = <1>;
 				clock-indices = <0>, <1>, <2>;
 				clock-output-names = "atlclk", "aplclk","gpuclk";
 			};
-			scpi_clk: scpi-clk {
+			scpi_clk: clocks-1 {
 				compatible = "arm,scpi-variable-clocks";
 				#clock-cells = <1>;
 				clock-indices = <3>;
@@ -578,7 +578,7 @@ scpi_clk: scpi-clk {
 			};
 		};
 
-		scpi_devpd: scpi-power-domains {
+		scpi_devpd: power-controller {
 			compatible = "arm,scpi-power-domains";
 			num-domains = <2>;
 			#power-domain-cells = <1>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 59/88] ARM: dts: rockchip: fix supply properties in io-domains nodes

[Sasha Levin]

From: Johan Jonker <jbx6244@gmail.com>

[ Upstream commit f07edc41220b14ce057a4e6d7161b30688ddb8a2 ]

A test with rockchip-io-domain.yaml gives notifications
for supply properties in io-domains nodes.
Fix them all into ".*-supply$" format.

Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Link: https://lore.kernel.org/r/20210606181632.13371-1-jbx6244@gmail.com
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/rk3288-rock2-som.dtsi | 2 +-
 arch/arm/boot/dts/rk3288-vyasa.dts      | 4 ++--
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/rk3288-rock2-som.dtsi b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
index 44bb5e6f83b1..76363b8afcb9 100644
--- a/arch/arm/boot/dts/rk3288-rock2-som.dtsi
+++ b/arch/arm/boot/dts/rk3288-rock2-som.dtsi
@@ -218,7 +218,7 @@ &io_domains {
 	flash0-supply = <&vcc_flash>;
 	flash1-supply = <&vccio_pmu>;
 	gpio30-supply = <&vccio_pmu>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
diff --git a/arch/arm/boot/dts/rk3288-vyasa.dts b/arch/arm/boot/dts/rk3288-vyasa.dts
index aa50f8ed4ca0..b156a83eb7d7 100644
--- a/arch/arm/boot/dts/rk3288-vyasa.dts
+++ b/arch/arm/boot/dts/rk3288-vyasa.dts
@@ -379,10 +379,10 @@ &io_domains {
 	audio-supply = <&vcc_18>;
 	bb-supply = <&vcc_io>;
 	dvp-supply = <&vcc_io>;
-	flash0-suuply = <&vcc_18>;
+	flash0-supply = <&vcc_18>;
 	flash1-supply = <&vcc_lan>;
 	gpio30-supply = <&vcc_io>;
-	gpio1830 = <&vcc_io>;
+	gpio1830-supply = <&vcc_io>;
 	lcdc-supply = <&vcc_io>;
 	sdcard-supply = <&vccio_sd>;
 	wifi-supply = <&vcc_18>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 60/88] ARM: dts: stm32: fix i2c node name on stm32f746 to prevent warnings

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit ad0ed10ba5792064fc3accbf8f0341152a57eecb ]

Replace upper case by lower case in i2c nodes name.

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32f746.dtsi | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32f746.dtsi b/arch/arm/boot/dts/stm32f746.dtsi
index 81a6fe653e66..d49e481b3aa6 100644
--- a/arch/arm/boot/dts/stm32f746.dtsi
+++ b/arch/arm/boot/dts/stm32f746.dtsi
@@ -360,9 +360,9 @@ i2c2: i2c@40005800 {
 			status = "disabled";
 		};
 
-		i2c3: i2c@40005C00 {
+		i2c3: i2c@40005c00 {
 			compatible = "st,stm32f7-i2c";
-			reg = <0x40005C00 0x400>;
+			reg = <0x40005c00 0x400>;
 			interrupts = <72>,
 				     <73>;
 			resets = <&rcc STM32F7_APB1_RESET(I2C3)>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 61/88] ARM: dts: stm32: move stmmac axi config in ethernet node on stm32mp15

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit fb1406335c067be074eab38206cf9abfdce2fb0b ]

It fixes the following warning seen running "make dtbs_check W=1"

Warning (simple_bus_reg): /soc/stmmac-axi-config: missing or empty
reg/ranges property

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp151.dtsi | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp151.dtsi b/arch/arm/boot/dts/stm32mp151.dtsi
index 84757901cd8d..b479016fef00 100644
--- a/arch/arm/boot/dts/stm32mp151.dtsi
+++ b/arch/arm/boot/dts/stm32mp151.dtsi
@@ -1395,12 +1395,6 @@ crc1: crc@58009000 {
 			status = "disabled";
 		};
 
-		stmmac_axi_config_0: stmmac-axi-config {
-			snps,wr_osr_lmt = <0x7>;
-			snps,rd_osr_lmt = <0x7>;
-			snps,blen = <0 0 0 0 16 8 4>;
-		};
-
 		ethernet0: ethernet@5800a000 {
 			compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
 			reg = <0x5800a000 0x2000>;
@@ -1424,6 +1418,12 @@ ethernet0: ethernet@5800a000 {
 			snps,axi-config = <&stmmac_axi_config_0>;
 			snps,tso;
 			status = "disabled";
+
+			stmmac_axi_config_0: stmmac-axi-config {
+				snps,wr_osr_lmt = <0x7>;
+				snps,rd_osr_lmt = <0x7>;
+				snps,blen = <0 0 0 0 16 8 4>;
+			};
 		};
 
 		usbh_ohci: usbh-ohci@5800c000 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 62/88] ARM: dts: stm32: fix the Odyssey SoM eMMC VQMMC supply

[Sasha Levin]

From: Grzegorz Szymaszek <gszymaszek@short.pl>

[ Upstream commit f493162319788802b6a49634f7268e691b4c10ec ]

The Seeed SoM-STM32MP157C device tree had the eMMC’s (SDMMC2) VQMMC
supply set to v3v3 (buck4), the same as the VMMC supply. That was
incorrect, as on the SoM, the VQMMC supply is provided from vdd (buck3)
instead.

Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
index 6cf49a0a9e69..b5601d270c8f 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -269,7 +269,7 @@ &sdmmc2 {
 	st,neg-edge;
 	bus-width = <8>;
 	vmmc-supply = <&v3v3>;
-	vqmmc-supply = <&v3v3>;
+	vqmmc-supply = <&vdd>;
 	mmc-ddr-3_3v;
 	status = "okay";
 };
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 63/88] ARM: dts: stm32: Drop unused linux, wakeup from touchscreen node on DHCOM SoM

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 5247a50c8b53ca214a488da648e1bb35c35c2597 ]

Fix the following dtbs_check warning:
touchscreen@38: 'linux,wakeup' does not match any of the regexes: 'pinctrl-[0-9]+'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index a2d903c0d57f..59b3239bcd76 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -187,7 +187,6 @@ touchscreen@38 {
 		reg = <0x38>;
 		interrupt-parent = <&gpiog>;
 		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
-		linux,wakeup;
 	};
 };
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 64/88] ARM: dts: stm32: Rename spi-flash/mx66l51235l@N to flash@N on DHCOM SoM

[Sasha Levin]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 9b8a9b389d8464e1ca5a4e92c6a4422844ad4ef3 ]

Fix the following dtbs_check warning:
spi-flash@0: $nodename:0: 'spi-flash@0' does not match '^flash(@.*)?$'

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: kernel@dh-electronics.com
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 2 +-
 arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi | 2 +-
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 2d027dafb7bc..f496bbfa0be6 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -330,7 +330,7 @@ &qspi {
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: mx66l51235l@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
index 803eb8bc9c85..a9eb82b2f170 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcor-som.dtsi
@@ -194,7 +194,7 @@ &qspi {
 	#size-cells = <0>;
 	status = "okay";
 
-	flash0: spi-flash@0 {
+	flash0: flash@0 {
 		compatible = "jedec,spi-nor";
 		reg = <0>;
 		spi-rx-bus-width = <4>;
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 65/88] ARM: dts: stm32: fix stpmic node for stm32mp1 boards

[Sasha Levin]

From: Alexandre Torgue <alexandre.torgue@foss.st.com>

[ Upstream commit 4bf4abe19089245b7b12f35e5cafb5477b3e2c48 ]

On some STM32 MP15 boards, stpmic node is not correct which generates
warnings running "make dtbs_check W=1" command. Issues are:

-"regulator-active-discharge" is not a boolean but an uint32.
-"regulator-over-current-protection" is not a valid entry for vref_ddr.
-LDO4 has a fixed voltage (3v3) so min/max entries are not allowed.

Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp157a-stinger96.dtsi   | 7 ++-----
 arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi | 5 +----
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi   | 5 +----
 arch/arm/boot/dts/stm32mp15xx-osd32.dtsi       | 7 ++-----
 4 files changed, 6 insertions(+), 18 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
index 58275bcf9e26..4dd138d691c7 100644
--- a/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
+++ b/arch/arm/boot/dts/stm32mp157a-stinger96.dtsi
@@ -184,8 +184,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -208,7 +206,6 @@ v1v8: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -219,13 +216,13 @@ bst_out: boost {
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
index b5601d270c8f..2d9461006810 100644
--- a/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c-odyssey-som.dtsi
@@ -173,8 +173,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -197,7 +195,6 @@ v1v2_hdmi: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			 bst_out: boost {
@@ -213,7 +210,7 @@ vbus_otg: pwr_sw1 {
 			 vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			 };
 		};
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index f496bbfa0be6..998ea30ae024 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -226,8 +226,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -249,7 +247,6 @@ v1v8: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -265,7 +262,7 @@ vbus_otg: pwr_sw1 {
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
diff --git a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
index 713485a95795..6706d8311a66 100644
--- a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
@@ -146,8 +146,6 @@ vtt_ddr: ldo3 {
 
 			vdd_usb: ldo4 {
 				regulator-name = "vdd_usb";
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
 				interrupts = <IT_CURLIM_LDO4 0>;
 			};
 
@@ -171,7 +169,6 @@ v1v2_hdmi: ldo6 {
 			vref_ddr: vref_ddr {
 				regulator-name = "vref_ddr";
 				regulator-always-on;
-				regulator-over-current-protection;
 			};
 
 			bst_out: boost {
@@ -182,13 +179,13 @@ bst_out: boost {
 			vbus_otg: pwr_sw1 {
 				regulator-name = "vbus_otg";
 				interrupts = <IT_OCP_OTG 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 
 			vbus_sw: pwr_sw2 {
 				regulator-name = "vbus_sw";
 				interrupts = <IT_OCP_SWOUT 0>;
-				regulator-active-discharge;
+				regulator-active-discharge = <1>;
 			};
 		};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 66/88] ARM: OMAP2+: Block suspend for am3 and am4 if PM is not configured

[Sasha Levin]

From: Tony Lindgren <tony@atomide.com>

[ Upstream commit 093a474ce10d8ea3db3ef2922aca5a38f34bab1b ]

If the PM related modules are not loaded and PM firmware not configured,
the system suspend fails to resume. Let's fix this by adding initial
platform_suspend_ops to block suspend and warn about missing modules.

When pm33xx and wkup_m3_ipc have been loaded and m3 coprocessor booted
with it's firmware, pm33xx sets up working platform_suspend_ops. Note
that we need to configure at least PM_SUSPEND_STANDBY to have
suspend_set_ops().

Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/mach-omap2/pm33xx-core.c | 40 +++++++++++++++++++++++++++++++
 1 file changed, 40 insertions(+)

diff --git a/arch/arm/mach-omap2/pm33xx-core.c b/arch/arm/mach-omap2/pm33xx-core.c
index 56f2c0bcae5a..bf0d25fd2cea 100644
--- a/arch/arm/mach-omap2/pm33xx-core.c
+++ b/arch/arm/mach-omap2/pm33xx-core.c
@@ -8,6 +8,7 @@
 
 #include <linux/cpuidle.h>
 #include <linux/platform_data/pm33xx.h>
+#include <linux/suspend.h>
 #include <asm/cpuidle.h>
 #include <asm/smp_scu.h>
 #include <asm/suspend.h>
@@ -324,6 +325,44 @@ static struct am33xx_pm_platform_data *am33xx_pm_get_pdata(void)
 		return NULL;
 }
 
+#ifdef CONFIG_SUSPEND
+/*
+ * Block system suspend initially. Later on pm33xx sets up it's own
+ * platform_suspend_ops after probe. That depends also on loaded
+ * wkup_m3_ipc and booted am335x-pm-firmware.elf.
+ */
+static int amx3_suspend_block(suspend_state_t state)
+{
+	pr_warn("PM not initialized for pm33xx, wkup_m3_ipc, or am335x-pm-firmware.elf\n");
+
+	return -EINVAL;
+}
+
+static int amx3_pm_valid(suspend_state_t state)
+{
+	switch (state) {
+	case PM_SUSPEND_STANDBY:
+		return 1;
+	default:
+		return 0;
+	}
+}
+
+static const struct platform_suspend_ops amx3_blocked_pm_ops = {
+	.begin = amx3_suspend_block,
+	.valid = amx3_pm_valid,
+};
+
+static void __init amx3_block_suspend(void)
+{
+	suspend_set_ops(&amx3_blocked_pm_ops);
+}
+#else
+static inline void amx3_block_suspend(void)
+{
+}
+#endif	/* CONFIG_SUSPEND */
+
 int __init amx3_common_pm_init(void)
 {
 	struct am33xx_pm_platform_data *pdata;
@@ -337,6 +376,7 @@ int __init amx3_common_pm_init(void)
 	devinfo.size_data = sizeof(*pdata);
 	devinfo.id = -1;
 	platform_device_register_full(&devinfo);
+	amx3_block_suspend();
 
 	return 0;
 }
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 69/88] arm64: dts: ls208xa: remove bus-num from dspi node

[Sasha Levin]

From: Mian Yousaf Kaukab <ykaukab@suse.de>

[ Upstream commit 8240c972c1798ea013cbb407722295fc826b3584 ]

On LS2088A-RDB board, if the spi-fsl-dspi driver is built as module
then its probe fails with the following warning:

[   10.471363] couldn't get idr
[   10.471381] WARNING: CPU: 4 PID: 488 at drivers/spi/spi.c:2689 spi_register_controller+0x73c/0x8d0
...
[   10.471651] fsl-dspi 2100000.spi: Problem registering DSPI ctlr
[   10.471708] fsl-dspi: probe of 2100000.spi failed with error -16

Reason for the failure is that bus-num property is set for dspi node.
However, bus-num property is not set for the qspi node. If probe for
spi-fsl-qspi happens first then id 0 is dynamically allocated to it.
Call to spi_register_controller() from spi-fsl-dspi driver then fails.
Since commit 29d2daf2c33c ("spi: spi-fsl-dspi: Make bus-num property
optional") bus-num property is optional. Remove bus-num property from
dspi node to fix the issue.

Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi | 1 -
 1 file changed, 1 deletion(-)

diff --git a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
index e7abb74bd816..4d34d82b898a 100644
--- a/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
+++ b/arch/arm64/boot/dts/freescale/fsl-ls208xa.dtsi
@@ -625,7 +625,6 @@ dspi: spi@2100000 {
 			clocks = <&clockgen 4 3>;
 			clock-names = "dspi";
 			spi-num-chipselects = <5>;
-			bus-num = <0>;
 		};
 
 		esdhc: esdhc@2140000 {
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 70/88] arm64: dts: imx8mq: assign PCIe clocks

[Sasha Levin]

From: Lucas Stach <l.stach@pengutronix.de>

[ Upstream commit 15a5261e4d052bf85c7fba24dbe0e9a7c8c05925 ]

This fixes multiple issues with the current non-existent PCIe clock setup:

The controller can run at up to 250MHz, so use a parent that provides this
clock.

The PHY needs an exact 100MHz reference clock to function if the PCIe
refclock is not fed in via the refclock pads. While this mode is not
supported (yet) in the driver it doesn't hurt to make sure we are
providing a clock with the right rate.

The AUX clock is specified to have a maximum clock rate of 10MHz. So
the current setup, which drives it straight from the 25MHz oscillator is
actually overclocking the AUX input.

Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mq.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
index 5e0e7d0f1bc4..c86cf786f406 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi
@@ -1258,6 +1258,14 @@ pcie0: pcie@33800000 {
 			         <&src IMX8MQ_RESET_PCIE_CTRL_APPS_EN>,
 			         <&src IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF>;
 			reset-names = "pciephy", "apps", "turnoff";
+			assigned-clocks = <&clk IMX8MQ_CLK_PCIE1_CTRL>,
+			                  <&clk IMX8MQ_CLK_PCIE1_PHY>,
+			                  <&clk IMX8MQ_CLK_PCIE1_AUX>;
+			assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>,
+			                         <&clk IMX8MQ_SYS2_PLL_100M>,
+			                         <&clk IMX8MQ_SYS1_PLL_80M>;
+			assigned-clock-rates = <250000000>, <100000000>,
+			                       <10000000>;
 			status = "disabled";
 		};
 
@@ -1287,6 +1295,14 @@ pcie1: pcie@33c00000 {
 			         <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_EN>,
 			         <&src IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF>;
 			reset-names = "pciephy", "apps", "turnoff";
+			assigned-clocks = <&clk IMX8MQ_CLK_PCIE2_CTRL>,
+			                  <&clk IMX8MQ_CLK_PCIE2_PHY>,
+			                  <&clk IMX8MQ_CLK_PCIE2_AUX>;
+			assigned-clock-parents = <&clk IMX8MQ_SYS2_PLL_250M>,
+			                         <&clk IMX8MQ_SYS2_PLL_100M>,
+			                         <&clk IMX8MQ_SYS1_PLL_80M>;
+			assigned-clock-rates = <250000000>, <100000000>,
+			                       <10000000>;
 			status = "disabled";
 		};
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 73/88] thermal/drivers/imx_sc: Add missing of_node_put for loop iteration

[Sasha Levin]

From: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>

[ Upstream commit 3da97620e8d60da4a7eaae46e03e0a494780642d ]

Early exits from for_each_available_child_of_node() should decrement the
node reference counter.  Reported by Coccinelle:

  drivers/thermal/imx_sc_thermal.c:93:1-33: WARNING:
    Function "for_each_available_child_of_node" should have of_node_put() before return around line 97.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210614192230.19248-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/thermal/imx_sc_thermal.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/thermal/imx_sc_thermal.c b/drivers/thermal/imx_sc_thermal.c
index b01d28eca7ee..8d76dbfde6a9 100644
--- a/drivers/thermal/imx_sc_thermal.c
+++ b/drivers/thermal/imx_sc_thermal.c
@@ -93,6 +93,7 @@ static int imx_sc_thermal_probe(struct platform_device *pdev)
 	for_each_available_child_of_node(np, child) {
 		sensor = devm_kzalloc(&pdev->dev, sizeof(*sensor), GFP_KERNEL);
 		if (!sensor) {
+			of_node_put(child);
 			of_node_put(sensor_np);
 			return -ENOMEM;
 		}
@@ -104,6 +105,7 @@ static int imx_sc_thermal_probe(struct platform_device *pdev)
 			dev_err(&pdev->dev,
 				"failed to get valid sensor resource id: %d\n",
 				ret);
+			of_node_put(child);
 			break;
 		}
 
@@ -114,6 +116,7 @@ static int imx_sc_thermal_probe(struct platform_device *pdev)
 		if (IS_ERR(sensor->tzd)) {
 			dev_err(&pdev->dev, "failed to register thermal zone\n");
 			ret = PTR_ERR(sensor->tzd);
+			of_node_put(child);
 			break;
 		}
 
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH AUTOSEL 5.10 76/88] arch/arm64/boot/dts/marvell: fix NAND partitioning scheme

[Sasha Levin]

From: Konstantin Porotchkin <kostap@marvell.com>

[ Upstream commit e3850467bf8c82de4a052619136839fe8054b774 ]

Eliminate 1MB gap between Linux and filesystem partitions.

Signed-off-by: Konstantin Porotchkin <kostap@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm64/boot/dts/marvell/cn9130-db.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/marvell/cn9130-db.dts b/arch/arm64/boot/dts/marvell/cn9130-db.dts
index ce49a70d88a0..d24294888400 100644
--- a/arch/arm64/boot/dts/marvell/cn9130-db.dts
+++ b/arch/arm64/boot/dts/marvell/cn9130-db.dts
@@ -258,7 +258,7 @@ partition@0 {
 			};
 			partition@200000 {
 				label = "Linux";
-				reg = <0x200000 0xd00000>;
+				reg = <0x200000 0xe00000>;
 			};
 			partition@1000000 {
 				label = "Filesystem";
-- 
2.30.2


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel