[PATCH 5.10 027/135] ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM

[PATCH 5.10 027/135] ARM: dts: stm32: Disable LAN8710 EDPD on DHCOM

[Greg Kroah-Hartman]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 36862c1ebc92a7e6fcc55002965c44b8ad17d4ca ]

The LAN8710 Energy Detect Power Down (EDPD) functionality might cause
unreliable cable detection. There are multiple accounts of this in the
SMSC PHY driver patches which attempted to make EDPD reliable, however
it seems there is always some sort of corner case left. Unfortunatelly,
there is no errata documented which would confirm this to be a silicon
bug on the LAN87xx series of PHYs (LAN8700, LAN8710, LAN8720 at least).

Disable EDPD on the DHCOM SoM, just like multiple other boards already
do as well, to make the cable detection reliable.

Fixes: 34e0c7847dcf ("ARM: dts: stm32: Add DH Electronics DHCOM STM32MP1 SoM and PDK2 board")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
index 8221bf69fefe..000af7177701 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-som.dtsi
@@ -133,6 +133,7 @@
 			reset-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
 			reset-assert-us = <500>;
 			reset-deassert-us = <500>;
+			smsc,disable-energy-detect;
 			interrupt-parent = <&gpioi>;
 			interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
 		};
-- 
2.30.2




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5.10 028/135] ARM: dts: stm32: Fix touchscreen IRQ line assignment on DHCOM

[Greg Kroah-Hartman]

From: Marek Vasut <marex@denx.de>

[ Upstream commit 15f68f027ebd961b99a1c420f96ff3838c5e4450 ]

While 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
fixed the LED0 assignment on the PDK2 board, the same commit did not
update the touchscreen IRQ line assignment, which is the same GPIO line,
shared between the LED0 output and touchscreen IRQ input. To make this
more convoluted, the same EXTI input (not the same GPIO line) is shared
between Button B which is Active-Low IRQ, and touchscreen IRQ which is
Edge-Falling IRQ, which cannot be used at the same time. In case the LCD
board with touchscreen is in use, which is the case here, LED0 must be
disabled, Button B must be polled, so the touchscreen interrupt works as
it should.

Update the touchscreen IRQ line assignment, disable LED0 and use polled
GPIO button driver for Button B, since the DT here describes baseboard
with LCD board.

Fixes: 7e5f3155dcbb4 ("ARM: dts: stm32: Fix LED5 on STM32MP1 DHCOM PDK2")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
To: linux-arm-kernel@lists.infradead.org
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi | 24 +++++++++++--------
 1 file changed, 14 insertions(+), 10 deletions(-)

diff --git a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
index 59b3239bcd76..633079245601 100644
--- a/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
+++ b/arch/arm/boot/dts/stm32mp15xx-dhcom-pdk2.dtsi
@@ -37,7 +37,7 @@
 		poll-interval = <20>;
 
 		/*
-		 * The EXTi IRQ line 3 is shared with touchscreen and ethernet,
+		 * The EXTi IRQ line 3 is shared with ethernet,
 		 * so mark this as polled GPIO key.
 		 */
 		button-0 {
@@ -46,6 +46,16 @@
 			gpios = <&gpiof 3 GPIO_ACTIVE_LOW>;
 		};
 
+		/*
+		 * The EXTi IRQ line 6 is shared with touchscreen,
+		 * so mark this as polled GPIO key.
+		 */
+		button-1 {
+			label = "TA2-GPIO-B";
+			linux,code = <KEY_B>;
+			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
+		};
+
 		/*
 		 * The EXTi IRQ line 0 is shared with PMIC,
 		 * so mark this as polled GPIO key.
@@ -60,13 +70,6 @@
 	gpio-keys {
 		compatible = "gpio-keys";
 
-		button-1 {
-			label = "TA2-GPIO-B";
-			linux,code = <KEY_B>;
-			gpios = <&gpiod 6 GPIO_ACTIVE_LOW>;
-			wakeup-source;
-		};
-
 		button-3 {
 			label = "TA4-GPIO-D";
 			linux,code = <KEY_D>;
@@ -82,6 +85,7 @@
 			label = "green:led5";
 			gpios = <&gpioc 6 GPIO_ACTIVE_HIGH>;
 			default-state = "off";
+			status = "disabled";
 		};
 
 		led-1 {
@@ -185,8 +189,8 @@
 	touchscreen@38 {
 		compatible = "edt,edt-ft5406";
 		reg = <0x38>;
-		interrupt-parent = <&gpiog>;
-		interrupts = <2 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
+		interrupt-parent = <&gpioc>;
+		interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* GPIO E */
 	};
 };
 
-- 
2.30.2




_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel