Re: [PATCH] arm64: dts: imx8m: add syscon node for display_blk_ctrl module regs

[Tommaso Merciai <tomm.merciai@gmail.com>]

On Mon, Nov 01, 2021 at 11:22:21PM -0500, Adam Ford wrote:
> On Mon, Nov 1, 2021 at 5:58 PM Tommaso Merciai <tomm.merciai@gmail.com> wrote:
> >
> > On Mon, Nov 01, 2021 at 11:35:49PM +0100, Ahmad Fatoum wrote:
> > > Hello Tommaso,
> > >
> > > On 01.11.21 23:28, Tommaso Merciai wrote:
> > > > Add system controller node for registers of module Display Block Control
> > > > (DISPLAY_BLK_CTRL, base address: 0x32e28000).
> > > > The DISPLAY_BLK_CTRL module contains general purpose registers (GPRs),
> > > > which control varied features of the associated peripherals.
> > > > Reference: IMX8MMRM Rev. 3, 11/2020, p 3897
> > > > ---
> > > >  arch/arm64/boot/dts/freescale/imx8mm.dtsi | 5 +++++
> > > >  1 file changed, 5 insertions(+)
> > > >
> > > > diff --git a/arch/arm64/boot/dts/freescale/imx8mm.dtsi b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > > index 2f632e8ca388..3e496b457e1a 100644
> > > > --- a/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > > +++ b/arch/arm64/boot/dts/freescale/imx8mm.dtsi
> > > > @@ -961,6 +961,11 @@ aips4: bus@32c00000 {
> > > >                     #size-cells = <1>;
> > > >                     ranges = <0x32c00000 0x32c00000 0x400000>;
> > > >
> > > > +                   dispmix_gpr: display-gpr@32e28000 {
> > > > +                           compatible = "fsl, imx8mm-iomuxc-gpr", "syscon";
> > >
> > > Please read vendor patches before submitting them. The space
> > > is out-of-place in the compatible and the compatible is wrong:
> > > This doesn't look like a i.MX8MM pin controller.
> > >
> > > Cheers,
> > > Ahmad
> >
> >   Hi Ahmad,
> >   Thanks for your review. Do you think this is correct?
> >
> >   compatible = "fsl,imx8mm-dispmix-gpr", "syscon";
> >
> >   Let me know.
> 
> There was already a driver created for the blk-ctrl stuff and it has a
> device tree binding at 32e28000.  It's tied into the power-domain
> system, so if you want to enable the csi, dsi, or lcd, etc. you can
> just reference the blt-ctrl power domain index, and it enables the
> device's gpc power domain and takes the corresponding device out of
> reset.

  Hi Adam,
  You mean using the gpcv2.c driver?
  
  drivers/soc/imx/gpcv2.c

  With the following node, to put out of reset eLCDIF and mipi_dsi:

  gpc: gpc@303a0000 {
	compatible = "fsl,imx8mm-gpc";
	reg = <0x303a0000 0x10000>;
	interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH>;
	interrupt-parent = <&gic>;
	interrupt-controller;
	#interrupt-cells = <3>;

	pgc {

	 #address-cells = <1>;
	 #size-cells = <0>;
	 pgc_mipi: power-domain@0 {
					#power-domain-cells = <0>;
					reg = <IMX8M_POWER_DOMAIN_MIPI>;
 				  };

	pgc_disp: power-domain@7 {
					#power-domain-cells = <0>;
					reg = <IMX8M_POWER_DOMAIN_DISP>;
 				 };
   };
  };

  Let me know.

  Thanks,
  Tommaso

> 
> adam
> >
> >   Thanks,
> >   Tommaso
> >
> > >
> > > > +                           reg = <0x32e28000 0x100>;
> > > > +                   };
> > > > +
> > > >                     usbotg1: usb@32e40000 {
> > > >                             compatible = "fsl,imx8mm-usb", "fsl,imx7d-usb";
> > > >                             reg = <0x32e40000 0x200>;
> > > >
> > >
> > >
> > > --
> > > Pengutronix e.K.                           |                             |
> > > Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
> > > 31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
> > > Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel