Re: [PATCH v2] thermal: imx: implement runtime PM support

[Oleksij Rempel <o.rempel@pengutronix.de>]

On Wed, Nov 10, 2021 at 11:07:31AM +0100, Michal Vokáč wrote:
> On 25. 10. 21 13:06, Petr Benes wrote:
> > Hi Oleksij,
> > 
> > On Thu, 21 Oct 2021 at 19:21, Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> > > 
> > > Hi Petr,
> > > 
> > > On Wed, Oct 20, 2021 at 05:53:03PM +0200, Petr Benes wrote:
> > > > On Wed, 20 Oct 2021 at 07:05, Oleksij Rempel <o.rempel@pengutronix.de> wrote:
> > > > > 
> > > > > Hi Petr and Michal,
> > > > > 
> > > > > I forgot to add you for v2 in CC. Please test/review this version.
> > > > 
> > > > Hi Oleksij,
> > > > 
> > > > It works good. with PM as well as without PM. The only minor issue I found is,
> > > > that the first temperature reading (when the driver probes) fails. That is
> > > > (val & soc_data->temp_valid_mask) == 0) holds true. How does
> > > > pm_runtime_resume_and_get() behave in imx_thermal_probe()?
> > > > Does it go through imx_thermal_runtime_resume() with usleep_range()?
> > > 
> > > How exactly did you reproduce it? Even more or less understanding how
> > 
> > I just placed my debug print into get_temp()
> > 
> >      if ((val & soc_data->temp_valid_mask) == 0) {
> >          dev_dbg(&tz->device, "temp measurement never finished\n");
> >          printk("Wrong temperature reading!!!!!!\n");
> >          return -EAGAIN;
> >      }
> > 
> > > this can potentially happen, i never had this issue on my HW. Is it something
> > > HW specific?
> > 
> > IMHO it is just product of the following sequence:
> > 
> > pm_runtime_set_active(&pdev->dev);
> > pm_runtime_enable(data->dev);
> > pm_runtime_resume_and_get(data->dev);
> > thermal_zone_device_enable(data->tz);
> > 
> > With assumption imx_thermal_runtime_resume() didn't run,
> > hence the sensor didn't get enough time to come up.
> > 
> > I didn't have time to spend it on and you have better knowledge of the
> > area. If it is not that straightforward I can try to diagnose it better.
> > 
> Hi Oleksij,
> Did you manage to further debug and reproduce this problem?
> Do you plan to send the v3?
> 
> Regarding your question about the HW - this problem occured once we
> upgraded the SoC on our SBC from i.MX6DL to i.MX6Q/QP. With the DualLite
> we never had this problem but the Quad is getting hot quite fast.
> We have pretty limited cooling options so the core is operated at its
> upper temperature limits when fully loaded.

Hi Michal,

Sorry, I was busy and lost this topic from my radar. I was not able to
reproduce it on my i.MX6Q and i.MX6QP died after other thermal voltage
experiments. Please, if you able to reproduce it, try to investigate
what is wrong, for example increasing wakeup time and/or and tracing
sleap/wake/get sequences.

Regards,
Oleksij
-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel